Professional Documents
Culture Documents
80010292V03 PDF
80010292V03 PDF
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
6-Port Antenna
85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
85010008 1 downtilt kit Downtilt angle: 0° – 8° 4.3 | 9.5 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
2598 | 102.3
2633 | 103.7
2671 | 105.2
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
936.4880/b ngmn 04.19.01.01 Subject to alteration.
Adjustment mechanism
with integrated scale
All dimensions
in mm | inches
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
6-Port Antenna
Layout of interface:
35 | 1.4
146 | 5.7 *
167 | 6.6 *
145 | 5.7
108 | 4.3
49 | 1.9
46 | 1.8
60 | 2.4
167 | 6.6
184 | 7.2
261 | 10.3 *
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Correlation Table
Frequency range Array Connector
936.4880/b ngmn 04.19.01.01 Subject to alteration.
B1
R1
152 [5.98]
100 [3.94]
[0.79–0.98]
40 [1.57]
72 [2.83]
20–25
40 [1.57]
15
2–1
4 4.53]
5–
[1.6
M10 MA = 25 Nm
M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]
20–25
[0.79–0.98]
Subject to alteration.
936.3920/c
Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions
for Adjustment Mechanism
1
2
2
➀ Adjustment wheel with twist-lock ➀ Thread for fixing the protective To set the downtilt angle exactly,
function. cap or the RCU (Remote Control you must look horizontally at the
➁ Downtilt spindle with integrated Unit). scale. The lower edge of the gear-
scale. ➁ Gearwheel for RCU power drive. wheel must be used for alignment.
0° – max.°
0° – max.°
Remove the protective cap. Set downtilt angle by rotating the Screw on the protective cap again.
adjustment wheel.
For a description of RCU installation please refer to the respective data sheet.
Page 1 of 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions for Feederline Installation
for Triple-band Antennas
Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To
tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool
(as shown below) in combination with a standard torque-wrench.
7
Adjustment mechanism Ventilation hole
(protective cap removed)
8 9
1 2
6 5 3 4