Professional Documents
Culture Documents
80010966-2018-R1.0 Page 1 of 10
8-Port Antenna
Page 2 of 10 80010966-2018-R1.0
8-Port Antenna
80010966-2018-R1.0 Page 3 of 10
8-Port Antenna
85010097 2 clamps Mast diameter: 110 – 220 | 4.3 – 8.7 9.4 | 20.7 1
85010099 1 downtilt kit Downtilt angle: 0° – 10° 10.6 | 23.4 1
0.7 | 1.5
1.4 | 3.1
86010162 Gender Adapter Solely to be used in combination with 0.045 | 0.099 1
86010163 Port Extender the FlexRET module 86010153V01 0.16 | 0.35 1
2485 | 97.8
2223 | 87.5
2438 | 96.0
Accessories (included in the scope of supply)
85010096 2 clamps Mast diameter: 55 – 115 | 2.2 – 4.5 5.0 | 11.0 1
86010153V01 FlexRET 1
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
Material: Reflector screen: Aluminum.
Fiberglass housing: It covers totally the internal antenna components. The special
3-way 6-way
AISG AISG
1) 22 | 0.9
2) 150 | 5.9
BTS1 BTS2 BTS3 3) 11 | 0.4
BTS1 BTS2 BTS3 BTS4 BTS5 BTS6
All dimensions
in mm | inches
For more information please refer to the respective data sheets.
Page 4 of 10 80010966-2018-R1.0
8-Port Antenna
Layout of interface:
175 | 6.9 *
240 | 9.4 *
Y1 Y1 R1 R1 R2 R2 Y2 Y2
L 6 L 5 L 2 L 1 R 4 R 3 R 8 R 7
1695-2690 1695-2690 698 - 960 698 - 960 698 - 960 698 - 960 1695-2690 1695-2690
93 | 3.7 *
126 | 5.0
226 | 8.9
326 | 12.8
426 | 16.8
508 | 20.0 *
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Correlation Table
Frequency range Array Connector
Y1 Y2
R1 R2
Left Right
936.5298/d
80010966-2018-R1.0 Page 5 of 10
Mounting Hardware
Clamp
(Wind Load Category “XH”)
Clamp
Type No. 85010096
Suitable for mm 55 – 115
mast diameter inches 2.2 – 4.5
Scope of supply 1 x lower clamp
1 x upper clamp
Material – Clamp Hot-dip galvanized steel
– Screws Hot-dip galvanized steel
– Nuts Stainless steel
Weight kg 5.0
lb 11.0
F Torque
MA = 40 Nm
Torque
MA = 40 Nm
upper clamp
H
D
Torque
MA = 40 Nm
Torque
E G H MA = 40 Nm
A B C
lower clamp
lower clamp upper clamp
1)
Attention!
Square of the screw must be
A B C D E F G H positioned in the square hole
before tightening the nut.
Subject to alteration.
80010966-2018-R1.0 Page 6 of 10
FlexRET
Please note:
If the Primary which controls the FlexRET system does not support the default ex-factory interface
setting, then the FlexRET must be switched to the appropriate standard of the Primary before installation.
Please contact Kathrein for further information.
If the FlexRET of an antenna has to be replaced, the FlexRET gets the information stored in the antenna
Startup of FlexRET
cable and scanning the antenna line devices (ALD) the used primary (e.g. NodeB, ALC, etc.)
xing the
connector must be 0.5 – 1.0 Nm (‘hand-tightened’).
The connector should be tightened by hand or by a special torque screw driver (order no.
85010080).
See also data sheet for Kathrein AISG-cable (86010007, ...).
Please note: To ensure the tightness of the RET System, Kathrein recommend the use of
Kathrein components only.
Please note: If the daisy chain output is not used, do not remove the protection cap.
For daisy chain operation, remove the protection cap and attach a control cable to interconnect
with the daisy chain input of the subsequent FlexRET or external RCU.
Please note: Do not remove the protection cap on the daisy chain output of the last FlexRET
or RCU device.
Subject to alteration.
936.5204
Page 8 of 10 80010966-2018-R1.0
936.5204 Subject to alteration. FCC – Statements
FCC – Statements
Subject to alteration.
936.5204
Page 10 of 10 80010966-2018-R1.0