Professional Documents
Culture Documents
AAT1011A
Features
www.DataSheet4U.com General Description
z 3-Channel PC Power Supply Supervisor with The AAT1011 is a 3-channel power supply
Minimized External Components
supervisor with 8KV ESD protection. It provides
z Over Voltage Protection for 3.3V / 5V / 12V Over Voltage Protection (OVP), Under Voltage
Output
Protection (UVP), and Power Good Indicator to
z Under Voltage Protection for 3.3V / 5V
monitor and control the output of the switching
Output with 75 ms Enable Delay
power supply system.
z Fault Protection Output with Open Drain
Output
Remote function from external signal, i.e., On/Off
z Open Drain Power Good Output
Control ( ONCTL ), is also implemented.
z 300 ms Power Good Delay
z 2.3 ms ONCTL to FPO Turn Off Delay Over voltage fault protection and under voltage
z 49 ms ONCTL Signal De-bounce fault protection can be directly triggered without
z 73 µs De-bounce external voltage divider.
TOP VIEW
PGI 1 8 PGO
GND 2 7 Vcc
FPO 3 6 V5
ONCTL 4 5 V33
(PDIP-8 PACKAGE)
*Spec is subject to change without notice in this document.
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0
Advanced Analog Technology, Inc.
AAT1011A
FPO (Fault Protection Output) OVP and UVP
NORMAL=“LOW”, FAULT=“HIGH” OVP monitors 3.3V, 5V, and 12V (via Vcc pin)
FPO indicates the fault condition of either Over UVP monitors 3.3V and 5V. OVP and UVP
Voltage or Under Voltage. When a fault state levels are determined by internal voltage dividers.
occurs, the FPO latched high and combined with a The typical values are 3.9V, 6.1V, 13.8V for OVP
low PGO output.
www.DataSheet4U.com and 2.83V, 4.3V for UVP, respectively.
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0
Advanced Analog Technology, Inc.
AAT1011A
Pin Description
Pin # Name I/O Description
1 PGI I Power Good Input signal
2 GND Ground
3 FPO O Inverted Fault Protection Output, open drain output stage
4 ONCTL I ON/OFF control input
www.DataSheet4U.com
5 V33 I Over and Under Voltage Protection for 3.3V
6 V5 I Over and Under Voltage Protection for 5V
7 VCC I Supply voltage and 12V over voltage protection input
8 PGO O Power Good Output signal, open drain output stage
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0
Advanced Analog Technology, Inc.
AAT1011A
Electrical Characteristics, VCC = 5 V (Unless Otherwise Specified)
Over Voltage Protection and Under Voltage Protection
Parameter Test Condition Min Typ Max Unit
V33 3.7 3.9 4.1
Over voltage threshold V5 5.7 6.1 6.5 V
VCC 13.3 13.8 14.3
www.DataSheet4U.com
Under-voltage V33 2.71 2.83 2.95
threshold V5 4.1 4.3 4.47 V
VCC 3.8
PGO and FPO
Parameter Test Condition Min Typ Max Unit
ILKG Leakage current (PGO) PGO = 5 V 5 µA
VOL Low level output voltage Isink = 10 mA 0.4 V
(PGO)
ILKG Leakage current ( FPO ) V( FPO ) = 5 V 5 µA
VOL Low level output voltage Isink = 10 mA 0.3 V
( FPO ) Isink = 30 mA 0.7
Operating Current
Parameter Test Condition Min Typ Max Unit
ICC Supply current ONCTL = 5 V 1 mA
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0
Advanced Analog Technology, Inc.
AAT1011A
Vcc
UVLO
VINT Power on Reset
OV12
GND V INT =3.58 V Reset
www.DataSheet4U.com
FPO
Level
Shift
Vref
OV12 R
POD
Vref 73 µs S POD2
S
Debounce
OV5
Q
Reset R Q
Vref R R
OV33
R
V5
UV5 OV5 75 ms
Delay
V33 R
PGO
UV33 OV33 Level
73 µs Shift
Debounce
Vref
UV5 R Q
POD
Vref 73 µs 300 ms
CLR Delay
Debounce
UV33
Vref
PGI Reset
POD2
Vcc POD Oscillator
Reset
150 uA
* 2.3 ms VBG =1.28 Bandgap
49 ms CLR Delay Reference
ONCTL POD
Debounce
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0
Advanced Analog Technology, Inc.
AAT1011A
Timing Chart
AAT1011
www.DataSheet4U.com
Vcc
Reset
ONCTL
FPO
PGI
3.3 V
5V
12 V
PGO
td1 td1 td1
tb1 tb1 PG OFF delay
td3
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0
Advanced Analog Technology, Inc.
AAT1011A
Package Dimension (Unit: Mil)
R10Max
(4X)
www.DataSheet4U.com
312 12
35020
250 4
R40
10
654 554
374 10
7Typ. 310Max.
355
15 Min.
115Min.
– 台灣類比科技股份有限公司 –
Advanced Analog Technology, Inc. V 1.0