Professional Documents
Culture Documents
Note: RSA is qualifying support for the major version. In case of any configuration changes or logs not
parsing in a minor version, please open a case and we will add support for it.
II. Configure R
SA NetWitness Platform for Syslog Collection
Configuration Steps
Field Action
Host Enter the IP address of the RSA NetWitness Log Decoder or Remote
Address Log Collector.
Description Type NetWitness
Server Enter 514
Port
4. Click Save.
5. To add logs for System Events:
a. From the left menu, choose Administration > External Servers > Syslog Export
Filters
Export Filters window in the General tab:
Field Action
c. Click Save.
6. To add logs for Audit Records:
a. Click Add Syslog Filter again, and enter the information provided below in the
Syslog Export Filters window in the General tab:
Field Action
b. Click Save.
7. To add Session Logs (with support for limited columns):
a. Click Add Syslog Filter again, and enter the information provided below in the
Syslog Export Filters window in the General tab:
Configuration Steps 17
Event Source Log Configuration Guide
Field Action
Note: RSA supports all of the Data Filter options.
d. Select a list of columns to be appended to the Syslog event from the Predefined
Field Groups and Available Columns drop-down lists.
Note: There is a list of columns that RSA currently supports in the Supported
Columns for Session Logs section. All Predefined Field Groups are currently
supported by RSA except for Posture Request and RADIUS Response.
e. Click Save.
8. Perform the following steps to add Insight logs.
a. Click Add Syslog Filter again, and enter the information provided below in the
Syslog Export Filters window in the General tab.
Field Action
18 Configuration Steps
Event Source Log Configuration Guide
Field Action
3.
c. Choose a data filter from the drop-down list.
Note: There is a list of columns that RSA currently supports in the Supported
Columns for Insight Logs section.
e. Click Save.
user_session_id username
l Configure Syslog Collection
2. In the Services grid, select a Log Decoder, and from the Actions menu, choose View
> Config.
3. In the Service Parsers Configuration panel, search for your event source, and ensure
that the Config Value field for your event source is selected.
Note: The required parser is arubacppm.
Note: You only need to configure Syslog collection the first time that you set up an event
source that uses Syslog to send its output to NetWitness.
You should configure either the Log Decoder or the Remote Log Collector for Syslog. You
do not need to configure both.
2. In the Services grid, select a Log Decoder, and from the Actions menu, choose View
> System.
3. Depending on the icon you see, do one of the following:
l If you see , click the icon to start capturing Syslog.
l If you see , you do not need to do anything; this Log Decoder is
already capturing Syslog.
2. In the Services grid, select a Remote Log Collector, and from the Actions menu,
choose View > Config > Event Sources.
3. Select Syslog/Config from the drop-down menu.
The Event Categories panel displays the Syslog event sources that are configured, if
any.
4. In the Event Categories panel toolbar, click +.
The Available Event Source Types dialog is displayed.
5. Select either syslog-tcp or syslog-udp. You can set up either or both, depending on
the needs of your organization.
7. Enter 514 for the port, and select Enabled. Optionally, configure any of the
Advanced parameters as necessary.
Click OK to accept your changes and close the dialog box.
Once you configure one or both syslog types, the Log Decoder or Remote Log Collector
collects those types of messages from all available event sources. So, you can continue
to add Syslog event sources to your system without needing to do any further
configuration in NetWitness.
Copyright © 2019 Dell Inc. or its subsidiaries. All Rights Reserved.
Trademarks
For a list of RSA trademarks, go to www.emc.com/legal/emc-corporation-
trademarks.htm#rsa .