Professional Documents
Culture Documents
3 662.2 640.2 --- --- --- --- --- --- --- --- ---
3-1/8 725.5 703.6 679.0 622.1 --- --- --- --- --- --- ---
3-1/4 791.5 769.5 744.9 688.0 --- --- --- --- --- --- ---
3-3/8 --- --- 813.5 756.6 689.3 --- --- --- --- --- ---
3-1/2 --- --- 884.6 827.7 760.5 --- --- --- --- --- ---
3-3/4 --- --- 1,034.6 977.7 910.5 --- --- --- --- --- ---
3-7/8 --- --- 1,113.5 1,056.6 989.4 911.8 823.8 --- --- --- ---
4 --- --- --- 1,138.1 1,070.9 993.3 905.3 --- --- --- ---
4-1/8 --- --- --- 1,222.2 1,154.9 1,077.3 989.4 --- --- --- ---
4-1/4 --- --- --- 1,308.8 1,241.6 1,164.0 1,076.0 --- --- --- ---
4-1/2 --- --- --- 1,489.9 1,422.6 1,345.0 1,257.1 --- --- --- ---
4-3/4 --- --- --- 1,681.3 1,614.0 1,536.4 1,448.5 1,350.2 --- --- ---
5 --- --- --- 1,883.0 1,815.8 1,738.2 1,650.3 1,552.0 --- --- ---
5-1/4 --- --- --- 2,095.2 2,027.9 1,950.3 1,862.4 1,764.1 1,626.7 --- ---
5-1/2 --- --- --- 2,317.6 2,250.3 2,172.7 2,084.8 1,986.5 1,849.1 1,758.9 ---
5-3/4 --- --- --- 2,550.4 2,483.1 2,405.5 2,317.6 2,219.3 2,081.9 1,991.7 ---
6 --- --- --- 2,793.5 2,726.3 2,648.7 2,560.7 2,462.4 2,325.0 2,234.8 2,105.5
6-1/4 --- --- --- 3,047.0 2,979.8 2,902.2 2,814.2 2,715.9 2,578.5 2,488.3 2,359.0
6-1/2 --- --- --- 3,310.9 3,243.6 3,166.0 3,078.1 2,979.8 2,842.4 2,752.1 2,622.8
6-3/4 --- --- --- 3,585.0 3,517.8 3,440.2 3,352.2 3,253.9 3,116.5 3,026.3 2,897.0
7 --- --- --- 3,869.6 3,802.3 3,724.7 3,636.8 3,538.5 3,401.1 3.310.9 3,181.5
7-1/4 --- --- --- 4,164.4 4,097.2 4,019.6 3,931.6 3,833.3 3,695.9 3,605.7 3.476.4
7-1/2 --- --- --- 4,469.7 4,402.4 4,324.8 4,236.9 4,138.6 4,001.2 3,910.9 3,781.6
7-3/4 --- --- --- 4,785.2 4,718.0 4,640.4 4,552.4 4,454.1 4,316.7 4,226.5 4,097.2
8 --- --- --- 5,111.1 5,043.9 4,966.3 4,878.3 4,780.0 4,642.6 4,552.4 4,423.1
8-1/4 --- --- --- 5,447.4 5,380.1 5,302.5 5,214.6 5,116.3 4,978.9 4,888.7 4,759.4
8-1/2 --- --- --- 5,794.0 5,726.7 5,649.1 5,561.2 5,462.9 5,325.5 5,235.3 5,106.0
8-3/4 --- --- --- 6,150.9 6,083.7 6,006.1 5,918.2 5,819.9 5,682.4 5,592.2 5,462.9
9 --- --- --- --- 6,451.0 6,373.4 6,285.4 6,187.2 6,049.7 5,959.5 5,830.2
9-1/4 --- --- --- --- 6,628.6 6,751.0 6,663.1 6,564.8 6,427.4 6,337.2 6,207.9
9-1/2 --- --- --- --- 7,216.6 7,139.0 7,051.1 6,952.8 6,815.4 6,725.2 6,595.8
9-3/4 --- --- --- --- 7,615.0 7,537.4 7,449.4 7,351.1 7,213.7 7,123.5 6,994.2
10 --- --- --- --- --- 7,946.1 7,858.1 7,759.8 7,622.4 7,532.2 7,402.9
10-1/4 --- --- --- --- --- 8,365.1 8,277.1 8,178.8 8,041.4 7,951.2 7,821.9
10-1/2 --- --- --- --- --- 8,794.5 8,706.5 8,608.2 8,470.8 8,380.6 8,251.3
10-3/4 --- --- --- --- --- 9,234.2 9,146.2 9,047.9 8,910.5 8,820.3 8,691.0
11 --- --- --- --- --- --- --- 9,498.0 9,360.6 9,270.4 9,141.1
11-1/4 --- --- --- --- --- --- --- 9,958.4 9,821.0 9,730.8 9,601.5
11-1/2 --- --- --- --- --- --- --- 10,429.2 10,291.8 10,201.6 10,072.2
11-3/4 --- --- --- --- --- --- --- 10,910.3 10,772.9 10,682.7 10,553.3
12 --- --- --- --- --- --- --- 11,401.8 11,264.3 11,174.1 11,044.8
1,000 lb. of steel will displace .364 bbl. 490 lb. of steel will displace 1 ft. .
3
65.5 lb. of steel will displace 1 gal. 2,747 lb. of steel will displace 1 bb.
7.84 kg of steel will displace 1 liter.
70957 1-5/8 0.2500 Per 6.000 1,100- 14,000 8,400 43,200 200 420 0.13 70822 ---
Order 1,400 46,300
64460 1-13/16 0.3125 1-13/16 6.000 1,360- 18,100 10,800 59,400 370 640 0.195 74223
Wilson 1,800 21150 ---
FJ 78074
50640 2-1/4 0.3750 1-1/4 8.000 1,560- 20,700 13,800 118,500 1,700 2,200 0.211 18775
API 2,100 54020 ---
REG.
68262 2-29/32 1.0000 2-3/8 12.750 2,200- 37,000 24,600 194,800 1,600 5,200 0.692 68010 ---
PH-6 3,000
55867 3-1/8 1.0000 2-3/8 8.750 2,400- 30,000 21,000 229,200 3,500 7,600 0.375 42736 72888
API 3,300 52504
REG.
55895 3-3/4 1.2500 2-7/8 8.250 4,200- 52,000 36,000 345,000 3,800 13,500 0.820 38040 145737
API 5,700 13255
REG. 52506
55747 3-3/4 1.5000 2-3/8 7.875 3,400- 43,500 30,000 299,700 3,800 13,000 .630 37406 ---
API IF 4,600 52528
50660 3-3/4 1.8750 2-3/8 7.625 3,500- 43,000 30,000 179,500 2,500 8,200 0.613 41355
EUE 4,700 20150 ---
52497
3 4-1/4 1.9375 2-7/8 8.625 3,500- 43,000 30,000 430,300 6,600 24,500 0.920 44483 80468
API IF 4,700 13640
52502
50708 4-1/2 2.3750 2-7/8 10.375 3,600- 49,000 32,000 375,000 4,000 25,900 1.150 35849 ---
EUE 4,900 52653
50700 4-3/4 1.5000 3-1/2 8.875 6,300- 78,000 54,000 591,900 9,500 27,600 1.000 25960 ---
API FH 8,500 52530
55812 4-3/4 2.0000 3-1/2 10.125 5,600- 63,000 43,000 468,800 9,500 27,100 1.350 38110 79789
API 7,500 52500
FH IF
55860 6 2.0000 4-1/2 8.625 10,200- 128,500 77,000 937,000 17,000 52,600 1.570 14710 145484
API FH 13,800 52498
55905 6-1/4 2.2500 4-1/2 13.000 11,800- 147,000 102,000 917,400 21,000 56,900 4.240 12370 79691
API IF 16,000 52544
50720 6-3/4 2.3750 5-1/2 13.000 13,000- 172,900 102,000 1,013,800 24,000 74,200 3.450 11130 145440
API 17,500 52680
REG.
55910 7-3/4 3.0625 6-5/8 13.000 11,000- 126,000 88,000 1,587,900 45,000 145,300 4.650 15160
API 15,000 52711 ---
REG.
78964 7-3/4 3.0625 6-5/8 12.000 12,100- 220,000 123,000 1,600,000 45,500 130,000 72978
API 20,500 --- ---
REG.
66372 9 3.7504 7-5/8 13.000 12,000- 200,000 100,000 1,621,000 70,000 224,700 3.200 66346
API 16,000 ---
REG.
1) All jarring and pulling loads shown in this manual assume that the force is acting alone and is essentially along the major
axis of the tool. If torque and tension or bending and tension are used together, the resulting combined stresses may lead
to failure at substantially less than rated loads. Rotation and bending together can lead to fatigue.
2) Min. pull required (above weight of string and collars) to obtain effective blow (lb.).
3) The strengths shown are theoretical calculations based on yield strength of the material used in each case.
The strengths shown are therefore accurate, plus or minus 20%.
Assy. Threaded Dia. Lift Load Max. Low Pull Standard Lowest Full
Part # Connection (in.) After Recommended Load Test Load Allowable Stroke
Jarring Jar Load (tons*) (tons*) Test Load Length
Outside Inside (tons) (tons*) (tons*) (in.)
(Nom.)
Nom. Size Measured Mandrel Mandrel Spline Body Connector Connector Connector Pressure
Tool OD Pkg. Ret. Body To To Body To Body Body To Body To
To Mandrel Spline Body Connector Connector Adapter To Pressure Washpipe
Body (Left Hand Body Body Pressure Body Body
(Left Hand Joint) Adapter Body
Joint)
* 2,000 lb/ton**.
This field uses setting loads chosen to provide a good trip load over a wide range of hole conditions.
There is a tendency, however, for the BHA required to trip to increase with depth and mud weight. It may be necessary
in deeper holes to increase the trip load or lower the load at a faster rate.
70822 Sub Type 1-5/8 0.2500 15,400 46,300 420 1,100 to 1,450
74723 Sub Type 1-13/16 0.3125 18,000 59,400 640 1,360 to 1,800
54020 Integral Mandrel 2-1/4 0.3750 21,000 118,500 2,200 1,560 to 2,100
68010 Sub Type 2-29/32 1.0000 35,400 194,800 5,200 2,200 to 3,000
55670 Sub Type 3-1/16 1.5000 31,300 160,200 5,900 2,300 to 3,100
52504 Integral Mandrel 3-1/8 1.0000 32,400 229,200 7,600 2,400 to 3,300
52506 Integral Mandrel 3-3/4 1.2500 56,500 345,000 13,500 4,200 to 5,700
52528 Sub Type 3-3/4 1.5000 46,000 299,700 13,000 3,400 to 4,600
52497 Sub Type 3-3/4 1.8750 46,500 179,500 8,200 3,500 to 4,700
52502 Integral Mandrel 4-1/4 1.9375 46,700 430,300 24,500 3,500 to 4,700
52653 Integral Mandrel 4-1/2 2.3750 49,000 375,000 25,900 3,600 to 4,900
52530 Integral Mandrel 4-3/4 1.5000 85,000 591,900 27,600 6,300 to 8,500
52500 Integral Mandrel 4-3/4 2.0000 74,500 468,800 27,100 5,600 to 7,500
52544 Integral Mandrel 6-1/4 2.2500 159,000 917,400 56,900 11,800 to 16,000
52680 Integral Mandrel 6-3/4 2.3750 172,800 1,013,800 74,200 13,000 to 17,500
52711 Integral Mandrel 7-3/4 3.0625 149,000 1,587,900 145,300 11,000 to 15,000
Top 6-5/8 4-1/2 3-1/2 3-1/2 2-3/8 REG. 2-3/8 REG. 2-3/8 REG. 2-3/8 REG.
Conn. REG. REG. REG. REG. (2-7/8 PACDS) (2-7/8 PACDS) (2-7/8 PACDS) (2-7/8 PACDS)
Cement Mills
Dressed Top Conn. Fishing Neck Pin ID Yield Torque Tensile Yield
Dia. (lb.)
Dia. (ft-lbs)
Flat Bottom
Dressed Dia. Top Connection Fishing Neck Pin ID Yield Torque Tensile Yield
Dia. (ft-lbs) (lb.)
Wicker Size Top Connection Fishing Neck Pin ID Yield Torque Tensile Yield lb.
(box) Dia. ft-lbs
Wicker Size Top Connection Fishing Neck Pin ID Yield Torque Tensile Yield lb.
(box) Dia. ft-lbs
Impression Blocks
Tool OD Top Connection Fishing Neck Dia. Pin ID Yield Torque ft-lbs Tensile Yield lb.
(box)
Fishing Magnets
Hole Size Top Connection Fishing Neck Pin ID Yield Torque Tensile Yield lb.
(box) Dia. ft-lbs
Washpipe Size Max. OD Dmft ID Yield Torque ft-lbs Tensile Yield lb.
Tool Series Top Connection Fishing Neck Pin ID Yield Torque Tensile Yield lb.
Dia. ft-lbs
Tool Series Top Connection Fishing Neck Dia. Pin ID Yield Torque Tensile Yield
ft-lbs lb.
Circulating Subs
Tool Series Top Connection Fishing Neck Dia. Pin ID Yield Torque Tensile Yield
ft-lbs lb.
Rope Spear
Tool Series Top Connection Fishing Neck Dia. Pin ID Yield Torque Tensile Yield
ft-lbs lb.