Professional Documents
Culture Documents
ASTM C 226 Standard Specification For Air-Entraining Additions For Use in The Manufacture of Air PDF
ASTM C 226 Standard Specification For Air-Entraining Additions For Use in The Manufacture of Air PDF
This standard has been approved for use by agencies of the Department of Defense.
--`-`-`,,`,,`,`,,`---
air-entraining addition to be interground with the clinker in the
manufacture of air-entraining hydraulic cement conforming to Mortar4
Specifications C 150, C 595, and C 1157. C 187 Test Method for Normal Consistency of Hydraulic
1.2 The values stated in SI units are to be regarded as the Cement4
standard. C 191 Test Method for Time of Setting of Hydraulic Ce-
1.3 This standard does not purport to address all of the ment by Vicat Needle4
safety concerns, if any, associated with its use. It is the C 192 Practice for Making and Curing Concrete Test Speci-
responsibility of the user of this standard to establish appro- mens in the Laboratory3
priate safety and health practices and determine the applica- C 204 Test Method for Fineness of Hydraulic Cement by
bility of regulatory limitations prior to use. (Warning—Fresh Air Permeability Apparatus4
hydraulic cementitious mixtures are caustic and may cause C 231 Test Method for Air Content of Freshly Mixed
chemical burns to skin and tissue upon prolonged exposure.2) Concrete by the Pressure Method3
C 293 Test Method for Flexural Strength of Concrete (Us-
2. Referenced Documents ing Simple Beam with Center-Point Loading)3
2.1 ASTM Standards: C 595 Specification for Blended Hydraulic Cements4
C 33 Specification for Concrete Aggregates3 C 596 Test Method for Drying Shrinkage of Mortar Con-
C 39 Test Method for Compressive Strength of Cylindrical taining Hydraulic Cement4
Concrete Specimens3 C 666 Test Method for Resistance of Concrete to Rapid
C 109/C 109M Test Method for Compressive Strength of Freezing and Thawing3
Hydraulic-Cement Mortars (Using 2-in. or 50-mm Cube C 1157 Performance Specification for Hydraulic Cement4
Specimens)4 2.2 ACI Standards:6
C 114 Test Methods for Chemical Analysis of Hydraulic ACI 211.1-77 Recommended Practice for Selecting Propor-
Cement4 tions for Normal and Heavyweight Concrete
C 115 Test Method for Fineness of Portland Cement by the
3. Materials
Turbidimeter4
C 138 Test Method for Density, (Unit Weight), Yield, and 3.1 Cements:
Air Content (Gravimetric) of Concrete3 3.1.1 In cases where it is desired that the proposed air-
C 143 Test Method for Slump of Hydraulic Cement Con- entraining addition be accepted for general use, tests shall be
crete3 made on six lots of cement ground at cement plants, using
C 150 Specification for Portland Cement4 commercial grinding equipment. From each of three different
samples of clinkers, two lots of cement shall be ground,
representing respectively: a Type I portland cement containing
not less than 9 % tricalcium aluminate (C3A), calculated as
1
This specification is under the jurisdiction of ASTM Commitee C01 on Cement specified in Table 1 of Specification C 150 and a Type II and a
and is the direct responsibility of Subcommittee C01.20 on Additions.
Type III portland cement conforming to Specification C 150.
Current edition approved June 10, 2002. Published August 2002. Originally
published as C 226 – 50 T. Last previous edition C 226 – 96.
2
See the section on Safety, Manual of Cement Testing, Annual Book of ASTM
5
Standards, Vol 04.01. Discontinued, see 1949 Annual Book of ASTM Standards, Part 3.
3 6
Annual Book of ASTM Standards, Vol 04.02. Available from the American Concrete Institute, P.O. Box 19150, Detroit, MI
4
Annual Book of ASTM Standards, Vol 04.01. 48219.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
--`-`-`,,`,,`,`,,`---
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).