Professional Documents
Culture Documents
Standard Practice
Developed and Approved by the
MSS
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
This MSS Standard Practice was developed under the consensus of the MSS Technical Committee 114 and the
MSS Coordinating Committee. The content of this Standard Practice is the result of the efforts of competent and
concerned volunteers to provide an effective, clear, and non-exclusive specification that will benefit the industry
as a whole. This MSS Standard Practice is intended as a basis for common practice by the manufacturer, the
user, and the general public. The existence of an MSS Standard Practice does not in itself preclude the
manufacture, sale, or use of products not conforming to the Standard Practice. Mandatory conformance is
established only by reference in a code, specification, sales contract, or public law, as applicable.
Unless otherwise specifically noted in this MSS SP, any standard referred to herein is identified by the date of
issue that was applicable to the referenced standard(s) at the date of issue of this MSS SP. (See Annex B.)
Non-toleranced dimensions in this Standard Practice are nominal, and, unless otherwise specified, shall be
considered “for reference only”.
In this Standard Practice all notes, annexes, tables, and figures are construed to be essential to the understanding
of the message of the standard, and are considered part of the text unless noted as "supplemental". All
appendices appearing in this document are construed as "supplemental". Supplemental" information does not
include mandatory requirements.
Substantive changes in this 2007 edition are “flagged” by parallel bars as shown
on the margins of this paragraph. The specific detail of the change may be
determined by comparing the material flagged with that in the previous edition.
Any part of this standard may be quoted. Credit lines should read `Extracted from MSS SP-118, 2007
with permission of the publisher, the Manufacturers Standardization Society. ' Reproduction prohibited
under copyright convention unless written permission is granted by the Manufacturers Standardization
Society of the Valve and Fittings Industry Inc.
Copyright ©, 1996 by
Manufacturers Standardization Society
of the
Valve and Fittings Industry, Inc.
Printed in U.S.A.
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
i
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
TABLE OF CONTENTS
SECTION PAGE
1 SCOPE ................................................................................................................................................. 1
2 MARKING .......................................................................................................................................... 1
3 DESIGN AND MATERIALS ............................................................................................................. 2
4 EXAMINATION AND TEST ............................................................................................................. 5
5 SHIPPING INFORMATION............................................................................................................... 5
TABLE
FIGURE
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
3 Typical Union Bonnet Inside Screw (ISRS) Globe Valve................................................................. 15
4 Typical Seal Weld Bonnet Outside Screw and Yoke (OS&Y) Globe Valve..................................... 15
5 Typical Piston Check Valve............................................................................................................... 16
6 Typical Ball Check Valve .................................................................................................................. 16
7 Typical Swing Check Valve .............................................................................................................. 17
8 Typical In-Line Check Valve, Flangeless or Insert Type .................................................................. 18
9 Typical In-Line Check Valve, Threaded Type .................................................................................. 18
ANNEX
ii
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
valves covered by this Standard Practice as and an OS&Y globe valve with bolted bonnets are
reduced seat port(2) valves. Valve sizes correspond presented in Figure 1 and Figure 2. Figures 3 and
to nominal pipe sizes listed in ASME B36.10M and 4 illustrate ISRS and OS&Y globe valves with
B36.19M. Flanged, flangeless, and butt weld end union and threaded and seal welded bonnet design,
valves are limited to NPS 4 and smaller; threaded respectively. Figures 5, 6, 7, 8, and 9 illustrate
and socket welding end valves are limited to NPS 2 typical check valves. The illustrations are provided
1/2 and smaller. Valves covered under this Standard to clarify certain design features. They are not
Practice shall meet the requirements of ASME intended to require products conforming in any
B16.34, "Standard Class". The following valves are detail to the valves shown.
covered by this Standard Practice:
2. MARKING
a) Class 800 valves with threaded, socket-
2.1 Valves shall be marked in accordance with
welding, or butt-welding ends: an inside screw with
the requirements of ASME B16.34 and shall
rising stem (ISRS) and threaded packing nut or an
include, but not be limited to the requirements of
outside screw and yoke (OS&Y) with rising stem
Sections 2.2 and 2.3.
and bolted, union, welded or threaded and seal
welded bonnet joint. 2.2 Valve bodies shall be marked as follows:
b) Class 1500 valves with threaded, socket- a) Threaded-end or socket-welding-end —
welding, buttwelding, or flanged ends; an OS&Y 150, 300, 600, 800, or 1500.
with rising stem and bolted packing-gland flange;
and a bolted, union, welded or threaded and seal b) Flanged-end or flangeless valves —
welded bonnet joint. 150, 300, 600, or 1500.
c) Buttwelding-end valves —
c) Classes 150, 300, and 600 flanged-end, 150, 300, 600, 800, or 1500.
flangeless end, threaded, socket-welding, or
buttwelding-end OS&Y valves with rising stem, 2.3 Each valve shall have a corrosion-resistant
bolted packing-gland flange, threaded gland, and metal identification plate, securely attached, giving
a bolted, union, welded or threaded and seal welded sufficient information to identify the product. The
bonnet joint. following information shall be included and may be
on the identification plate or on the body (See
Section 2.2.):
(1)
This Standard Practice is not intended for valves developed
for and predominantly used in instrument piping systems. a) Manufacturer
See MSS SP-99, or MSS SP-105. b) Manufacturer's model, type, figure number, etc.
c) Size
(2)
The term "reduced port" is defined by comparison to a full d) Applicable pressure rating at 100°F
port as identified in Appendix A of ASME B16.34 for the e) Body material
appropriate pressure class. f) Trim material
g) MSS SP-118 may be included
1
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
2.4 For valves with welded on flange or 3.2.3 End flanges shall conform to ASME B16.5.
buttwelding stub ends, the material grade, along
with the post-weld treatment conditions, shall be 3.2.4 Flanged-end valves may have the flanges
indicated on the identification plate, stamped on integral with or welded to the body. The
the body, or both requirements of Paragraph 2.1.6, ASME B16.34
shall apply to valves with welded flanged ends.
2.5 The body of the globe valve may include an
arrow marking to indicate preferred direction of 3.2.5 Flanged-end valves shall have face-to-face
flow. Check valves require a flow direction dimensions conforming to ASME B16.10
arrow. This directional marking shall be integral 3.2.6 Unless otherwise specified in the purchase
with the body, forged-in, cast-in, or permanently order, the facing finish of end flanges and flangeless
etched or stamped on. end valves shall be in accordance with the
3. DESIGN AND MATERIALS requirements of ASME B16.5.
3.1 Pressure-Temperature Ratings 3.2.7 The end-to-end dimensions for Classes 150,
300, 600, and 1500 buttwelding-end valves shall
3.1.1 The pressure-temperature ratings for Class conform to ASME B16.10. Buttwelding-end
800 valves shall be as shown in Table 1. The valves may have stub ends integral with or welded
pressure-temperature ratings in Table 1 are an to the body. Welded ends shall be welded on to the
interpolation between Standard Class 600 and body in accordance with the requirements of 3.2.4.
Standard Class 900 pressure-temperature ratings
listed in ASME B16.34 for the appropriate valve 3.2.8 The end-to-end dimensions for socket-weld-
material. ing-end, threaded-end valves, Class 800
buttwelding-end valves and flangeless valves shall
3.1.2 The pressure-temperature ratings for Class be the manufacturer's standard.
150, 300, 600, and 1500 valves shall conform to
the corresponding Standard Class pressure- 3.2.9 Unless otherwise specified in the purchase
temperature ratings listed in ASME B16.34 for the order, buttwelding ends shall conform to ASME
appropriate valve material. B16.25 for the bore specified in the purchase order
for use without backing rings.
3.2 End Connections
3.2.10 For all austenitic stainless steel valves,
3.2.1 Threaded-end valves shall be internally taper- welded on flange or buttwelding stub end valves
threaded as specified in ASME B1.20.1. All internal shall be solution annealed after welding unless both
threads shall be countersunk a distance of the body and the flanges or buttwelding stub ends are
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
approximately one-half the pitch of the thread at an solution annealed L (low carbon) grades or stabilized
angle of approximately 45 degrees with the axis of grades of stainless steel. Post weld heat treatment shall
the thread. Counterstriking shall be concentric with be in accordance with Paragraph 2.1.6, ASME B16.34.
the threads. The valve end shall meet Table 4,
ASME B16.34 requirements for the appropriate 3.3 Body and Bonnet
pressure class. 3.3.1 The valve body, bonnet, check valve covers,
3.2.2 Socket-welding-end preparation shall and union nuts shall be made from a material
conform to ASME B16.11. The bottom of the specified in the purchase order using one of the
socket shall be square and flat. The minimum wall product form materials listed in Table 1 of ASME
thickness of socket welding end valves shall be in B16.34.
accordance with requirements of Table 4, ASME
B16.34.
2
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
3.3.2 The minimum body wall thickness at any 3.5.2 If an overlay weld-deposit is used for the disc
point (except at end connections - See Sections or piston seat and/or body seating surface, the base
3.2.1 and 3.2.2) shall be in accordance with ASME material for the disc/piston and/or body seat shall
B16.34. Class 800 values are given in Table 3 for have a corrosion resistance at least equal to the
convenience. material of the valve body.
3.3.3 The minimum bonnet wall thickness at any 3.5.3 Table 4 lists the nominal seating surface
point below the bottom ring of packing shall not be materials categorized by trim numbers.
less than the values required by ASME B16.34.
Class 800 values are given in Table 3 for 3.5.4 Except as provided in a) through c) below,
convenience. the standard trim number shall be specified in Table
2. When a trim other than standard is desired, it
3.4 Body-Bonnet Joint shall be specified on the purchase order by a trim
number from Tables 4 and 5. The typical
3.4.1 The body-bonnet joint design shall be either
specifications included in Tables 4 and 5 are listed
bolted, union, welded, or threaded and seal welded.
to illustrate generally accepted material
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
3.4.2 The bolted body-bonnet joint design shall compositions and are not intended to be exact
have a minimum of four cap screws, studs, or stud material requirements.
bolts. Cap screws shall be external wrenching type.
a) If a specified trim number listed below is
3.4.3 Bolting material shall conform to Table 2 required by either Table 2 or the purchase order, the
except that other bolting combinations (not listed in manufacturer may at his option furnish an
Table 2) may be used by agreement between the alternative trim number as follows:
purchaser and the manufacturer provided they are in
Specified Alternative
accordance with ASME B16.34.
Trim No. Trim No.
3.4.4 Unless otherwise specified in the purchase
1 8 or 8A
order, bolted and union body-bonnet joints shall be 101 108 or 108A
designed to confine the gasket and prevent over 2 10
compression. 5A 5
105A 105
3.4.5 Unless otherwise specified in the purchase 6 8
order, the body-bonnet joint, including the gasket, 106 108
shall be suitable for the pressure-temperature rating 8A 8
of the valve. The metallic portion of the gasket shall 108A 108
have a corrosion resistance at least equal to the 10 12
corrosion resistance of the shell material. 15 16
3.5.5 Trims not listed in Tables 4 and 5 may be 3.7.4 The stem shall have a surface finish Ra of
used by agreement between the purchaser and the 32 microinch or smoother in the area of contact
manufacturer. with the packing.
3.6.1 The disc of globe valves shall be of either 3.8.1 Globe valve discs shall be accurately guided
(a) flat-faced type, (b) plug type, or as specified by a stem or body guide throughout the travel
by purchaser (e.g., needle-point type). distance to its seat. Check valve piston, balls, or
discs shall be accurately guided to the seat by the
3.6.2 The check mechanism of check valves shall body, bonnet, or separate cage.
be either of the piston type, ball type, inline type,
or swing check type. 3.9 Seats
3.6.3 The covers of check valves shall be of the 3.9.1 The body seats shall be threaded, with or
bolted, welded, or union nut design. without welded overlays, welded or brazed-in
type, or integral with the body.
3.6.4 The check mechanism of check valves shall
be designed to close by gravity when installed in 3.10 Port Opening
a horizontal position. Inline check valves shall
use a spring to close the check mechanism. At 3.10.1 The bore of the body seats for globe and
the manufacturer's option, a spring may be installed check valves shall not be less than that shown in
in the piston, ball or inline designs to preload the Table 7, except inline check valve bores shall be
closure mechanism. Swing check valves may be the manufacturer's standard.
used in vertical lines where the normal flow is in 3.11 Threaded Packing-Gland Assembly
the upward direction.
3.11.1 The packing-gland assembly shall include
3.7 Stem a steel gland located under the packing nut. A
3.7.1 Globe valve stem or disc nut shall have a separate packing ring or washer at the base of the
shoulder that will backseat against the bonnet in packing is permissible and shall be of a material
the fully open position. The stem-to-disc connection whose nominal composition is equal to valve
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
4
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
3.12.4 Swinging eyebolts should be of either the 4.1.3 Supplementary examinations are required
hinge-pin or trunnion type. only if specified in the purchase order and only to
the extent specified. Magnetic particle,
3.13 Packing Material radiographic, liquid penetrant, and ultrasonic
3.13.1 Unless otherwise specified in the purchase examination of steel forgings and castings shall be
order, the packing shall be suitable for the pressure in accordance with MSS SP-53, SP-54, SP-93, and
temperature rating of the valve within a design SP-94 or with the purchaser's own acceptance
temperature range of -20°F to 1000°F. The packing criteria.
shall contain a corrosion inhibitor. 4.2 Pressure Test
3.13.2 The minimum depth of packing material 4.2.1 Except as noted in Section 4.2.2, each valve
furnished shall be as listed in Table 8 for Class 800 shall be pressure tested by the manufacturer as
and 1500 valves. For Class 150, 300, and 600 globe specified in MSS SP-61 and ASME B16.34.
valves minimum depth of packing shall be
manufacturer's standard. Packing-gland adjustment 4.2.2 No visually detectable leakage is allowed for
length remaining after testing with the gland tight the duration of the closure test of NPS 2" and
shall be greater than 10 percent of the minimum smaller globe valves and resilient seated check
packing depth listed in Table 8. valves. The maximum allowable closure leakage for
metal seated check valves shall be 3 ml of
3.14 Stuffing Box liquid/min./unit of NPS or 1.5 cu ft. of gas/hr./unit
3.14.1 The stuffing box finish shall be Ra of 125 of NPS.
microinch or smoother unless otherwise specified in 4.3 Repair of Defects
the purchase order.
4.3.1 Defects in the shell of a cast or forged valve,
3.15 Stem Nut revealed by inspection or test, shall be repaired as
3.15.1 Stem nuts of OS&Y globe valves shall be permitted by the applicable material specification or
made of a material resistant to galling and corrosion ASME B16.34.
and have a minimum melting point of 1750°F. Gray 5. SHIPPING INFORMATION
cast iron is prohibited.
3.16 Handwheel 5.1 End Protection for Female Threaded and
Socket-Welding Ends
3.16.1 Handwheels shall be of a spoked design;
shall be made of carbon steel, ductile iron, or 5.1.1 Except for individually packaged valves,
malleable iron; and shall be of ample size for easy the female ends of threaded and socket-welding
opening and closing. Clockwise rotation of the ends shall be protected with metal, wood, or
handwheel shall close the valve. Cast iron or non- plastic plugs.
ferrous materials shall not be used.
5.2 End Protection of End Flanges and Butt-
4. EXAMINATION AND TEST Welding Ends
4.1 Examination 5.2.1 End flanges and buttwelding ends shall be
4.1.1 A visual examination shall be performed by covered to protect gasket surfaces, welding ends,
the valve manufacturer of all bodies, bonnets, and valve internals. Covers shall be wood fiber,
covers, and closure elements to assure conformance wood, plastic, or metal.
with material specifications and ASME B16.34.
Castings shall comply with the requirements of
MSS SP-55.
4.1.2 All nondestructive examinations shall be
performed in accordance with written procedures.
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
5
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
TABLE 1 Pressure-Temperature Ratings for Class 800 Globe & Check Valves (a)
(a) For a material shown in Table 1 that is acceptable for low temperature service, the pressure rating for a service at any
temperature below -20°F shall be no greater than the rating shown in Table 1 for -20°F to 100°F.
(b) Upon prolonged exposure to temperature above 800°F, the carbide phase of steel may be converted to graphite. Permissible
but not recommended for prolonged use above about 800°F.
(c) Only killed steel shall be used over 850°F.
(d) Not to be used over 650°F.
(e) Use normalized and tempered material only.
(f) Permissible but not recommended for prolonged use above about 1100°F.
(g) Not to be used over 1100°F.
(h) At temperature over 1000°F, use only when the carbon content is 0.04% or higher.
(i) Not to be used over 800°F.
(j) Not to be used over 850°F.
(k) For temperature over 1000°F, use only if the material is heat treated by heating to a minimum temperature of 2000°F.
(l) Not to be used over 1000oF.
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
6
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
TABLE 1 Pressure-Temperature Ratings for Class 800 Globe & Check Valves (a)
(Continued)
7
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
Source: This table and the following notes are extracted from ASME B16.34, Table 1, except for standard trim
and bolting columns and notes a, b, c, d, and e,. Reprinted by courtesy of ASME International, Three
Park Ave., New York, New York 10016.
NOTES: (a) Temperature limitations on bolting are as follows: Gr B7, 1000°F; Gr L7, 1000°F; Gr B16,
1000°F;
Gr B8-CL 1, Gr B8A-CL 1A, Gr B8M-CL 1, and Gr B8MA-CL 1A, 1500°F; Gr B8-CL 2,
Gr B8M-CL 2, Gr B8M2-CL 2B and Gr B8M3-CL 2C, 1000°F.
(b) ASTM A 320, Gr L7 bolts, and ASTM A 194, Gr 4 nuts are also acceptable.
(c) ASTM A 193, Gr B8-CL 1, Gr B8A-CL 1A, Gr B8M-CL 1, Gr B8MA-CL 1A, Gr B8M2-CL 2B,
and B8M3-CL 2C bolting may be subsituted, provided that the requirements of Section 3.4 are met.
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
8
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
1/4 0.12
3/8 0.13
1/2 0.16
3/4 0.19
1 0.22
1 1/4 0.23
1 1/2 0.24
2 0.28
2 1/2 0.33
3 0.38
4 0.47
9 --`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
10
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
Typical
Trim Material Hardness Specification
Number (Note) Type (HB) (Type)
1 13Cr 200 Min. ASTM A 276-T410 or T420
ASTM A 276-T410 or T420
101 13Cr 200 Min.
ASTM A 582-T416
2 18Cr-8Ni Manufacturer’s Standard ASTM A276-T304
3 25Cr-20Ni Manufacturer’s Standard ASTM A276-T310
4 through 8A 13Cr 200 Min. ASTM A 276-T410 or T420
104
105
105A
ASTM A 276-T410 or T420
106 13Cr 200 Min.
ASTM A 582-T416
107
108
108A
9 and 11 Ni-Cu Alloy Manufacturer’s Standard Manufacturer’s Standard
10 and 12 18Cr-8Ni Manufacturer’s Standard ASTM A276-T316
13 and 14 19Cr-29Ni Manufacturer’s Standard ASTM B473
15 18Cr-8Ni Manufacturer’s Standard ASTM A276-T304
16 18Cr-8Ni Manufacturer’s Standard ASTM A276-T316
17 18Cr-8Ni Manufacturer’s Standard ASTM A276-T347
18 19Cr-29Ni Manufacturer’s Standard ASTM B473
Note: Trims 1 and 4 through 8A denote trims that prohibit free-machining grades of 13 % Cr material.
11
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
(a) See Section 3.7.2 A finish machining tolerance of 0.005 inches is permitted.
(a) In-line check valves minimum bore diameters shall be manufacturer’s standard.
12
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
13
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
PART NAMES
PART NAMES
1. Handwheel Nut
1. Handwheel Nut
2. Handwheel
2. Handwheel
3. Identification Plate
3. Identification Plate
4. Stem
4. Stem
5. Packing Nut
5. Stem Nut
6. Gland
6. Yoke
7. Packing
7. Gland Bolting
8. Packing Ring (when used)
8. Gland
9. Bonnet
9. Packing
10. Bonnet Bolting
10. Bonnet Bolting
11. Gasket
11. Bonnet
12. Disc Nut
12. Gasket
13. Disc
13. Disc Nut
14. Body
14. Disc
15. Body
FIGURE 1 FIGURE 2
Typical Inside Screw with Rising Typical Outside Screw and Yoke
Stem (ISRS) Globe Valve (OS&Y) Globe Valve
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
14
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
PART NAMES
PART NAMES
1. Handwheel Nut
2. Identification Plate
3. Handwheel 1. Handwheel Nut
4. Stem 2. Identification Plate
5. Gland 3. Handwheel
6. Packing Nut 4. Stem
7. Packing 5. Stem Nut
8. Packing Ring (when used) 6. Yoke
9. Bonnet 7. Gland Bolting
10. Gasket 8. Gland
11. Bonnet Nut 9. Packing
12. Disc Nut 10. Bonnet
13. Disc 11. Disc Nut
14. Body 12. Disc
13. Body
FIGURE 3 FIGURE 4
Typical Union Bonnet Inside Screw Typical Seal Weld Bonnet Outside
(ISRS) Globe Valve Screw and Yoke (OS&Y) Globe Valve
15
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
FIGURE 5 FIGURE 6
Typical Piston Check Valve Typical Ball Check Valve
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
16
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
PART NAMES
1. Fastener
2. Identification Plate
3. Bonnet Bolting
4. Gasket
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
5. Hinge
6. Bonnet/Cover
7. Disc
8. Hinge Pin
9. Seat Ring
10. Disc Nut
11. Body
12. Alignment Pin
FIGURE 7
Typical Swing Check Valve
17
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
1. Yoke 1. Yoke
2. Spring 2. Spring
3. Body 3. Body
4. Cap (Disc) 4. Cap (Disc)
FIGURE 8 FIGURE 9
Typical In-Line Check Valve Typical In-Line Check Valve
Flangless or Insert Type Threaded Type
18
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
ANNEX A
Referenced Standards and Applicable Dates
This Annex is an integral part of this Standard Practice and is placed after the main text for convenience.
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
B16.10-2000 Face-to-Face and End-to-End Dimensions of Ferrous Valves
B16.11-2005 Forged Steel Fittings, Socket-Welding and Threaded
B16.25-2003 Butt-Welding Ends
B16.34-2004 Valves -- Flanged, Threaded, and Welding-End
B36.10M-2004 Welded and Seamless Wrought Steel Pipe
B36.19M-2004 Stainless Steel Pipe
AWS
19
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
MSS STANDARD PRACTICE SP-118
ANNEX A
Referenced Standards and Applicable Dates
(continued)
MSS
SP-53-1999 (R 02) Quality Standard for Steel Castings and Forgings for Valves, Flanges, and Fittings and
Other Piping Components -- Magnetic Particle Examination Method
SP-54-1999 (R 02) Quality Standard for Steel Castings for Valves, Flanges and Fittings and Other
Piping Components -- Radiographic Examination Method
SP-55-2001 Quality Standard for Steel Castings for Valves, Flanges and Fittings, and Other Piping
Components -- Visual Method
SP-61-2003 Pressure Testing of Steel Valves
SP-93-1999 (R 04) Quality Standard for Steel Castings and Forgings for Valves, Flanges, and Fittings and
Other Piping Components -- Liquid Penetrant Examination Method
SP-94-1999 (R 04) Quality Standard for Ferritic and Martensitic Steel Castings for Valves, Flanges, and
Fittings and Other Piping Components -- Ultrasonic Examination Method
SP-99-1994 (R 05) Instrument Values
SP-105-1996 (R 05) Instrument Valves for Code Applications
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
Three Park Avenue
New York, NY 10016-5990
MSS Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.
127 Park Street, N.E.
Vienna, VA 22180-4602
20
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT
List of MSS Standard Practices
(Price List Available Upon Request)
Number
SP-6-2001 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings
SP-9-2001 (R 05) Spot Facing for Bronze, Iron and Steel Flanges
SP-25-1998 Standard Marking System for Valves, Fittings, Flanges and Unions
SP-42-2004 Class 150 Corrosion Resistant Gate, Glove, Angle and Check Valves with Flanged and Butt Weld Ends
SP-43-1991 (R 01) Wrought Stainless Steel Butt-Welding Fittings
SP-44-2006 Steel Pipeline Flanges
SP-45-2003 Bypass and Drain Connections
SP-51-2007 Class 150LW Corrosion Resistant Flanges and Cast Flanged Fittings
SP-53-1999 (R 07) Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components - Magnetic Particle
Examination Method
SP-54-1999 (R 07) Quality Standard for Steel Castings for Valves, Flanges, and Fittings and Other Piping Components - Radiographic Examination Method
SP-55-2006 Quality Standard for Steel Castings for Valves, Flanges and Fittings and Other Piping Components - Visual Method for Evaluation of
Surface Irregularities
SP-58-2002 Pipe Hangers and Supports - Materials, Design and Manufacture
SP-60-2004 Connecting Flange Joint Between Tapping Sleeves and Tapping Valves
SP-61-2003 Pressure Testing of Steel Valves
SP-65-2004 High Pressure Chemical Industry Flanges and Threaded Stubs for Use with Lens Gaskets
SP-67-2002a Butterfly Valves
SP-68-1997 (R 04) High Pressure Butterfly Valves with Offset Design
SP-69-2003 Pipe Hangers and Supports - Selection and Application (ANSI/MSS Edition)
SP-70-2006 Gray Iron Gate Valves, Flanged and Threaded Ends
SP-71-2005 Gray Iron Swing Check Valves, Flanged and Threaded Ends
SP-72-1999 Ball Valves with Flanged or Butt-welding Ends for General Service
SP-75-2004 Specification for High Test Wrought Butt Welding Fittings
SP-77-1995 (R 00) Guidelines for Pipe Support Contractual Relationships
SP-78-2005a Gray Iron Plug Valves, Flanged and Threaded Ends
SP-79-2004 Socket-Welding Reducer Inserts
SP-80-2003 Bronze Gate, Globe, Angle and Check Valves
SP-81-2006 Stainless Steel, Bonnetless, Flanged, Knife Gate Valves
SP-83-2006 Class 3000 Steel Pipe Unions, Socket-Welding and Threaded
SP-85-2002 Gray Iron Globe & Angle Valves, Flanged and Threaded Ends
SP-86-2002 Guidelines for Metric Data in Standards for Valves, Flanges, Fittings and Actuators
SP-88-1993 (R 01) Diaphragm Valves
SP-89-2003 Pipe Hangers and Supports - Fabrication and Installation Practices
SP-90-2000 Guidelines on Terminology for Pipe Hangers and Supports
SP-91-1992 (R 96) Guidelines for Manual Operation of Valves
SP-92-1999 MSS Valve User Guide
SP-93-1999 (R 04) Quality Standard for Steel Castings and Forgings for Valves, Flanges, and Fittings and Other Piping Components - Liquid Penetrant
Examination Method
SP-94-1999 (R 04) Quality Std for Ferritic and Martensitic Steel Castings for Valves, Flanges, and Fittings and Other Piping Components - Ultrasonic
Examination Method
SP-95-2006 Swage(d) Nipples and Bull Plugs
SP-96-2001 (R 05) Guidelines on Terminology for Valves and Fittings
SP-97-2006 Integrally Reinforced Forged Branch Outlet Fittings - Socket Welding, Threaded and Buttwelding Ends
SP-98-2001 (R 05) Protective Coatings for the Interior of Valves, Hydrants, and Fittings
SP-99-1994 (R 05) Instrument Valves
SP-100-2002 Qualification Requirements for Elastomer Diaphragms for Nuclear Service Diaphragm Valves
SP-101-1989 (R 01) Part-Turn Valve Actuator Attachment - Flange and Driving Component Dimensions and Performance Characteristics
SP-102-1989 (R 01) Multi-Turn Valve Actuator Attachment - Flange and Driving Component Dimensions and Performance Characteristics
SP-104-2003 Wrought Copper Solder Joint Pressure Fittings
SP-105-1996 (R 05) Instrument Valves for Code Applications
SP-106-2003 Cast Copper Alloy Flanges and Flanged Fittings, Class 125, 150 and 300
SP-108-2002 Resilient-Seated Cast-Iron Eccentric Plug Valves
SP-109-1997 (R 06) Welded Fabricated Copper Solder Joint Pressure Fittings
SP-110-1996 Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends
SP-111-2001 (R 05) Gray-Iron and Ductile-Iron Tapping Sleeves
SP-112-1999 (R 04) Quality Standard for Evaluation of Cast Surface Finishes -Visual and Tactile Method. This SP must be sold with a 10-surface, three
Dimensional Cast Surface Comparator, which is a necessary part of the Standard. Additional Comparators may be sold separately.
SP-113-2001 Connecting Joint between Tapping Machines and Tapping Valves
SP-114-2001 Corrosion Resistant Pipe Fittings Threaded and Socket Welding, Class 150 and 1000
SP-115-2006 Excess Flow Valves, 1 1/4 NPS and Smaller, for Fuel Gas Service
SP-116-2003 Service Line Valves and Fittings for Drinking Water Systems
SP-117-2006 Bellows Seals for Globe and Gate Valves
SP-118-2007 Compact Steel Globe & Check Valves - Flanged, Flangeless, Threaded & Welding Ends (Chemical & Petroleum Refinery Service)
SP-119-2003 Factory-Made Belled End Socket Welding Fittings
SP-120-2006 Flexible Graphite Packing System for Rising Stem Steel Valves (Design Requirements)
SP-121-2006 Qualification Testing Methods for Stem Packing for Rising Stem Steel Valves
SP-122-2005 Plastic Industrial Ball Valves
SP-123-1998 (R 06) Non-Ferrous Threaded and Solder-Joint Unions for Use with Copper Water Tube
SP-124-2001 Fabricated Tapping Sleeves
SP-125-2000 Gray Iron and Ductile Iron In-Line, Spring-Loaded, Center-Guided Check Valves
SP-126-2000 Steel In-Line Spring-Assisted Center Guided Check Valves
SP-127-2001 Bracing for Piping Systems Seismic-Wind-Dynamic Design, Selection, Application
SP-128-2006 Ductile Iron Gate Valves
SP-129-2003 Copper-Nickel Socket-Welding Fittings and Unions
SP-130-2003 Bellows Seals for Instrument Valves
SP-131-2004 Metallic Manually Operated Gas Distribution Valves
SP-132-2004 Compression Packing Systems for Instrument Valves
SP-133-2005 Excess Flow Valves for Low Pressure Fuel Gas Appliances
SP-134-2006a Valves for Cryogenic Service Including Requirements for Body/Bonnet Extensions
SP-135-2006 High Pressure Steel Knife Gate Valves
(R-YEAR) Indicates year standard reaffirmed without substantive changes
A large number of former MSS Practices have been approved by the ANSI or ANSI Standards, published by others. In order to maintain a single source
of authoritative information, the MSS withdraws its Standard Practices in such cases.
Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.
127 Park Street, N.E., Vienna, VA 22180-4620 (703) • 281-6613 Fax # (703) 281-6671
MSS-IHS SP
--`,`,`,`,,``,`````,`,`,,``,,,,,-`-`,,`,,`,`,,`---
Copyright MSS
Provided by IHS under license with MSS Licensee=Inelectra Panama s de RL/5983191001, User=Gonzalez, Arturo
No reproduction or networking permitted without license from IHS Not for Resale, 08/01/2012 17:28:29 MDT