Professional Documents
Culture Documents
Section K Horizontal Lifeline Systems PDF
Section K Horizontal Lifeline Systems PDF
A-0
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
EASY SLIDERTM
HORIZONTAL LIFELINE
FALL PROTECTION SYSTEMS
TABLE OF CONTENTS
Thaler Or Equal K-0
WHAT IT TAKES TO BE
THALER OR EQUAL
When specifications read Thaler or Equal, it is the responsibility of specifiers and building owners to determine what it means to be “Or
Equal”. The following data has been presented to quickly help assess the comparative merits of “competitive” products. Thaler Horizontal
Lifeline products have a number of Value Added features that should be considered when trying to equate the “Or Equal”.
Protects up to 4 workers simultaneously; depending on anchor spacing, and number of shuttle runners
provided, Thaler “EASY SLIDER” is designed to protect up to 4 workers from falling, on same system.
Superior cable composition; 3/8” (10 mm) diameter Type 304 stainless steel, 7 x 19 structure provides
unlimited line strength, added strength, and extra margin of safety.
Added anchor strength; all anchor posts are designed to resist without fracture a pullout force of 5400 lbs
(24.02 kN), applied in the most adverse direction.
Specify any angle for corners; in addition to common corner angles such as 45°, 90°, 135°, any angle in 1°
increments way be specified without additional cost.
Cost advantage to building owner; most Thaler “EASY SLIDER” system components are fabricated in-house
thereby eliminating middle-man suppliers which can result in significant savings. “EASY SLIDER” is one of the
most cost-efficient horizontal lifeline systems on the market. Be sure to obtain accurate cost data before making
specifying decision.
“EASY SLIDER” means hands free movement; users travel full length of horizontal lifeline without disconnect-
ing while having both hands free.
Aesthetically pleasing flashing; pre-formed Thaler STACK JACK flashing used with roof anchor posts are
arguably the best , most reliable, maintenance-free flashing product on the market today. The STACK JACK relies
on memory in the EPDM seals to prevent leaks from above and condensation from below (air barrier design). See
Thaler STACK JACK flashing literature (Section A of manual), or Thaler EPDM Flashing Seals literature.
Long distance between supports; a single line horizontal lifeline system such as the Thaler K-703 “EASY
SLIDER” reduces the number of roof penetrations by providing up to 80’-0” (24.4 m) distance between supports
using a double TEA (Thaler Energy Absorber) in the horizontal cable, or 60’-0” (18.3 m) distance using single TEA.
Maintenance-Free; except for occasional wiping of any dirt that has accumulated on the stainless steel horizon-
tal cable, and annual inspection (by others), the “EASY SLIDER” requires no maintenance. In addition the STACK
JACK flashing used for the anchor posts is simply and cleanly installed without messy vaulking seals.
20 year Warranty; guaranteed against leaks and defects in materials and/or manufacture when installed in
accordance with Thaler "Installation Instructions".
K-0
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
(TEA)
PRIMER
A Pre-Engineered, Hands Free Fall Protection System For Roof,
Wall & Overhead Applications
K-1
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com K-1
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
A fall from elevation (the uncontrolled drop from one level to Can anyone know if a serious or fatal fall will occur in
another) is similar to winning the lottery. You never know the first few seconds of a worker’s career or 30 years later
when it is going to happen. in the last few seconds? Professionally, any safety approach
must assume the first few seconds, and building owners or
The quality management concept that 99.9% reliability is not their agents must immediately act to control a fall hazard,
good enough should be the watchword for building design- which is likely to result in serious or fatal injury if the fall
ers or owners when it comes to fall protection. occurs.
Fall protection can be profitable. At present, the losses in
injury/fatality costs and suffering are staggering. The cost of Fall protection is the back-up system planned for a worker
fall protection currently is incurred at the legal and compen- who could potentially lose his or her balance at height. It is
sation end of the economic cycle, rather than at the planning a planned response used to control or eliminate injury
or equipment use stage. Plaintiff lawyers know that the vio- potential where foreseeable fall hazards are present.
lation of OSHA, CSA or department of labor standards or
rules, and the general lack of common sense when it comes Fall protection can minimally be applied by the use of per-
to fall hazards, is rampant in almost every industry in North sonnel fall protection equipment with pre-designated
America. anchorage points, and a cable-type horizontal lifeline,
mounted on roof, wall or overhead surfaces, to provide safe
mobility at elevation, including travel to and from worksta-
tions e.g. window cleaning, mechanical equipment, roof
edge, around skylights (interior falls), narrow roof areas and
similar locations.
Single Span horizontal lifeline used to access and provide fall protection
for window cleaning operations.
TM EASY SLIDER is a registered trade mark of Thaler Metal industries Ltd. Patent and design pending
K-1A
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
HORIZONTAL LIFELINES
The EASY SLIDER horizontal lifeline designs offered by However, the heart of the EASY-SLIDER systems are embod-
Thaler Metal Industries consists of a stainless steel cable ied in the mobile shuttle runner and Thaler Energy Absorber.
installed horizontally and used for the attachment of a work- Here’s how they work.
er’s lanyard or lifeline device (self-retracting lifeline or syn-
thetic lifeline with rope grab) while moving horizontally. It is
used to control dangerous pendulum-like swing falls by lim-
iting free fall distance.
Intermediate Carabiner
Bracket
Shackle
Tensioner
Shuttle
K-1B
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
Minimum Clearance
lowing chart.
INITIAL SAG REQUIREMENT, 450 lbs (204 kg), 2 men falling 6’-0” (1.8 m)
PLANNING ASSISTANCE
Without obligation, Thaler Metal Industries Ltd. will provide
layout drawings for EASY SLIDER systems in compliance with
all applicable standards, safety regulations and local build-
ing codes.
K-1D
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
RELATED DATA
Refer to the following specific product data or other Thaler EPDM Triple Pressure Grommet
literature for Thaler EASY SLIDER Horizontal Lifeline fall pro- Seal Features:
Eliminates Leaks
tection systems (Section K of Thaler Manual). Eliminates Maintenance EPDM Base Seal Features:
- K-700 (Roof Application) Eliminates Removable Cap Eliminates Condensation &
- K-701 (Wall Application) Condensation Build-Up
Eliminates Vapour Return
- K-702 (Overhead Application) Eliminates Urethane Insulation
- K-703 (Single Span Application) Aluminum, Copper or
Incorporates Air Barrier Principles
- Specification (Section of Work, 3-Part Format) Stainless Steel Flashing
- Components
- What It Takes To Be “Thaler Or Equal”
- STACK JACK Flashings (Section A of Manual)
- EPDM Flashing Seals (Section A of Manual)
- Horizontal Lifeline For Metal roofs (Section D of Manual)
- Fall Arrest Roof Anchors (Section I of Manual)
Deck Flange
Thaler STACK JACK Flashing meets the requirements for air leakage
control better than any protrusion flashing on the market to-day (better
looking too).
THALER THALER
Thaler EASY-SLIDER Horizontal Lifeline for Metal Roofs (see Section D Metal USA Inc. Metal Industries Ltd.
of Manual)
Canada 1-800-387-7217 U.S. 1-800-576-1200 Internet: www.thalermetal.com e-mail: info@thalermetal.com
K-1E
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
ROOF SPECIALTIES
K-700 EASY SLIDERTM
Mechanical
K-700 HORIZONTAL
EASY SLIDERLIFELINE
TM FALL
PROTECTION SYSTEM
HORIZONTAL LIFELINE FALL
Equipment 1/2" (13 mm) (Roof Application)
throut 3/8" (10 mm) 304 PROTECTION SYSTEM
S.S. CABLE
S.S. INTERMEDIATE (Roof Application)
BRACKET 2-1/4" (57 mm) 3/4" 1/4" x 3-1/2" (6 mm x 89 mm) DESCRIPTION:
DESCRIPTION
(19 mm) HSS WELDED TO 1/2" x 8" x 8" The Thaler K-700 EASY SLIDERTM Horizontal Lifeline Fall
The Thaler K-700 EASY SLIDERTM Horizontal Lifeline
(12 mm x 203 mm x 203 mm) Protection System is a complete pre-engineered multi-span
Fall ProtectionflexibleSystem is a consisting
complete of endpre-engi-
BASE PLATE USING lifeline system anchors, intermediate
ea neered multi-span flexible lifeline system consist-devices
Ar 5/16" (8 mm ) FILLET WELD, anchors, stainless steel cable, mobile attachment
oof ALL HOT DIP GALVANIZED
ing of end (shuttle
anchors, runners),intermediate
in-line fittings anchors,
(tensioner, energystain-absorber,
R less steel corner
cable, mobile
w fittings, etc.) andattachment
up to 4 shuttles as devices
standard. Full body
rro Less Than 6’-0” (1.8 m), EPDM TRIPLE PRESSURE AND URETHANE INSULATED
Na Common Fall Hazard Area GROMMET TOP SEAL TO PREVENT CORROSION (shuttle runners),
harnesses in-line
with 6’-0” fittings
(1.8 m) (tensioner, energy lanyards
long shock absorbing
(by others)
absorber, corner completes
fittings, etc.)theand assembly.
up to End4 and intermediate
shuttles
THALER SJ-35 NEW-STANDARD as standard. anchors
Full body consistharnesses
of urethane insulated
with 6’-0” hollow
(1.8 steel
m)posts (HSS)
STACKJACK FLASHING (ALUMINUM,long shockequipped absorbing with different
lanyards type (by
headsothers)
to accommodate
com- the cable,
2005
(swaged end, energy absorber, double locking carabiner, shuttles end tensioner, intermediate brackets, corner pieces); Type 304 s.s. cable, 3/8” (10 mm) (continued on left)
cable, 3/8” (10 mm) dia. 7 x 19 structure); [2][4] full body harnesses with integral shock absorber by others; [SJ-34, CAL OSHA, AISC, AWS, and other references.
dia. 7 x 19 structure); [2][4] full body harnesses with integral shock absorber by others; [SJ-34, 7” (178 mm) high] [ SJ-35 13” (330 mm) high]
7” (178 mm) high] [ SJ-35 13” (330 mm) high] New-Standard STACK JACK Flashing of [.064” (1.6 mm) mill finish 1100- See Thaler EASY SLIDER Horizontal Lifeline Primer
New-Standard STACK JACK Flashing of [.064” (1.6 mm) mill finish 1100-0T alloy aluminum] [.032” (0.831 mm) 24 oz. copper] [.031” (0.79 mm) 22 ga.
0T alloy aluminum] [.032” (0.831 mm) 24 oz. copper] [.031” (0.79 mm) 22 ga. Type 304 stainless steel] to CSA B272- literature for introductory data on subject of fall
Type 304 stainless steel] to CSA B272-93, with EPDM Triple Pressure Grommet Top Seal and EPDM Base Seal and [bituminous painted deck flange] [PVC
93, with EPDM Triple Pressure Grommet Top Seal and EPDM Base Seal and [bituminous painted deck flange] [PVC protection.
coated deck flange]; manufactured by Thaler Metal Industries, 1-800-387-7217 (Mississauga, Ontario, Canada) or 1-800-576-1200 (New Braunfels, TX),
Thaler STACK JACK coated deck flange]; manufactured by Thaler Metal Industries, 1-800-387-7217 (Mississauga, Ontario, Canada) or WARRANTY
THALER
information. Products are typically available from stock.
Canada 1-800-387-7217 U.S. 1-800-576-1200 Internet: www.thalermetal.com e-mail: info@thalermetal.com K-2 K-2
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Note: All Anchors are designed to resist without fracture a pull-out force of 5400 lbs (24.02 kN), applied in the most adverse direction Note: Anchor to roof slab fastening shows adhesive bolt securement
(for retrofit applications)
3/8" (10 mm) STAINLESS STEEL END 30-0" (9.15 m) MAX. SPACING BETWEEN ANCHORS 3/8" (10 mm) STAINLESS STEEL END
BRACKET WELDED TO 4-1/2" (114 mm) FOR SYSTEM WITH ONE ENERGY ABSORBER BRACKET WELDED TO 4-1/2" (114 mm)
DIA x 1/4 (6 mm) GALVANIZED HSS S.S. INTERMEDIATE BRACKET AND 30'-0" TO 60'-0" (9.15 m to 18.30 m) DIA x 1/4 (6 mm), HSS
BOLTED TO TOP PLATE FOR SYSTEM WITH TWO ENERGY ABSORBERS 316L STAINLESS STEEL STAINLESS STEEL
SHUTTLE SWAGED END
1/2" 2-1/4"
2-1/4"
(12 mm) (57 mm)
(57 mm) 7/8" (22 mm)
TENSIONER TYPE 304 3/8" (10 mm) TYPE 304 3/8" (10 mm)
STAINLESS NOTE: UP TO 4 PERSONNEL PERMITTED STAINLESS
STEEL CABLE, ON SYSTEM AS STANDARD WITH STEEL CABLE,
1/2"
7 x 19 STRUCTURE MAXIMUM OF 2 WORKERS BETWEEN 7 x 19 STRUCTURE
(12 mm)
ANCHORS AT ANY ONE TIME
THALER ENERGY ABSORBER (TEA).
ONE TEA REQUIRED FOR ANCHOR
CARABINER, LANYARD SPACING UP TO 30'-0" (9.15 m) AND
OR SELF RETRACTING INVERTED ROOF
ILLUSTRATED 12-5/8" 321 mm) TWO TEA'S FOR ANCHOR SPACING
LIFELINE BY OTHERS FROM 30'-0" (9.15 m) TO 60'-0" (12.3 m)
CONVENTIONAL ROOF
ILLUSTRATED (BUR)
MIN. 5" (127 mm)
END ANCHOR WITH TENSIONER INTERMEDIATE ANCHOR INTERMEDIATE ANCHOR END ANCHOR WITH ENERGY ABSORBER CORNER ANCHOR
Intermediate Shackle
Bracket
Carabiner
MINIMUM 6"
WELDED TO
(152 mm)
BOLTS, LOCK WASHERS BASE PLATE
AND NUTS
DEFORM THREADS
AS PER CSA OR OSHA
GUIDELINE
(9.15 m) thereafter
1" (25 mm)
1/4" X 4" x 4" HSS FLANGE IN LAYER
TYPE 304 S.S.
(6 mm x 102 mm x 102 mm) OF PLASTIC CEMENT (BUR)
BOLT AND NUT
BY OTHERS
WELDED TO
Tensioner
FOUR 5/8"(16 mm) S.S.
BOLTS, LOCK WASHER BASE PLATE
AND NUTS
5/8" x 8" x 8"
(16 mm x 203 mm x 203 mm)
Shuttle
STEEL PLATE
On Cable
Terminal Corner
Anchor With Intermediate
HORIZONTAL LIFELINE SYSTEM Bolt-Around OWSJ (K-FARA-6-700) Hollow-Core Slab (K-FARA-7-700)
Tensioner And Corner Anchor
(Single Straight Line)
Energy Absorber
K- 2A K-2A
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
ROOF SPECIALTIES
K-701 EASY SLIDERTM
Inset Shows Top View of Corner Scenario K-701 EASY SLIDER LIFELINE
HORIZONTAL TM
CONTINUOUS CAULKING
FALL PROTECTION
HORIZONTAL LIFELINE SYSTEM
AROUND WALL PLATES 3/8" (10 mm) S.S.
END BRACKET WELDED TO
(Wall Application)
FALL PROTECTION SYSTEM
(BY OTHERS)
Intermediate TO 5/8" x 8" x 8"
(Wall Application)
(16 mm x 203 mm x 203 mm)
Anchor 2-3/4" (70 mm) S.S. WALL PLATE
DESCRIPTIONDESCRIPTION:
304 3/8" (10 mm) STAINLESS
The Thaler
STEEL CABLE,
The Thaler K-701, EASY K-701,
SLIDEREASYTMSLIDERTM
Horizontal Horizontal
LifelineLifeline Fall
7 x 19 STRUCTURE
Protection
SHACKLE Fall Protection SystemSystem for walls
for walls is ais complete
a complete pre-engineered
pre-
EASY SLIDER 6’-6” (1.98 m)
multi-span flexible
engineered multi-span flexiblelifeline systemsystem
lifeline consistingcon- of end wall
anchors, intermediate anchors, stainless steel cable, mobile
Lifeline Recommended Typical sisting of end wall anchors, intermediate anchors,
attachment devices (shuttle runners), in-line fittings (tensioner,
Corner Anchor Spacing From Roof Edge stainless steeltension
cable, mobile
indicator, energy attachment
absorber, corner devices
fittings, etc.) and up
(90° Illustrated) STAINLESS STEEL (shuttle runners),
to 4 in-lineas fittings
shuttles standard. (tensioner,
Full body tension
harnesses with 6’-0” (1.8
SWAGED END
indicator, energy absorber, corner
m) long shock absorbing lanyards (by others) fittings, etc.)
completes the
and up to 4system.
shuttles End as
and standard. Full body
intermediate anchors consist har-
of stainless
End nesses with 6’-0”
steel (1.8 m) long
base plates with shock
s.s. end absorbing
bracket with two lan-holes.
Intermediate Wall Anchor FRONT VIEW Anchors
yards (by others) are also available
completes the with different
system. End typeand bases for
MINIMUM
Anchor Roof Access 5" (127 mm) CONTINUOUS 5/16 (8 mm)
THALER ENERGY ABSORBER (TEA)
intermediatefastening
anchors to wall or similarof
consist structures.
stainless All anchors
steel are
K-FARA-93-710 Hatch
FILLET WELD base plates with s.s. end bracket with two holes. of 5400 lbs
designed to resist without fracture a pull-out force
K-700 EASY SLIDER MINIMUM
Anchors are(24.02 alsokN), applied in the most adverse direction.
With Thaler EASY 6" (152 mm) available with different type
(Roof Application) FOUR 5/8" (16 mm) 30'-0" (9.15 m) MAX. SPACING
bases for fastening to wall or similar structures. All
SLIDER Shuttle ADHESIVE FASTENERS BETWEEN ANCHORS FOR SYSTEM PROMINENT FEATURES:
anchors are Designed
designed to resist
(RETROFIT APPLICATION) WITH ONE ENERGY ABSORBER to protect up to without
2 workersfracture
against fallsafrom height
SECTION VIEW pull-out forceforofsystems
5400 lbs in (24.02
length up tokN), applied
200’-0” (61 m) in
andthe 4 workers for
30'-0" TO 60'-0" (9.15 TO 18.3 m)
FOR SYSTEM WITH TWO ENERGY
most adversethedirection.
systems more than 200’-0” (61 m) as standard (from
ABSORBERS Prominent Features:
falling moreDesigned
than 6’-0” orto 1.8protect
m). Handsup freeto 2 allows
system
workers againstusers falls
to walkfrom heightthefor
uninterrupted systems
entire length of in system. Thaler
length up to Energy
200’-0” Absorber
(61 m) (TEA),andseparate from harness
4 workers for the shock absorber
Any-Angle systems more assists
than in dissipating
200’-0” or(61 reducing
m) as fall arrest
standardforces. EASY
End Anchor SLIDER shuttle permits worker to connect or disconnect at any
Corner Anchor (from falling more than 6’-0” or 1.8 m). Hands free
position on cable. Line length is unlimited. Maintenance free.
NOTE: ADHESIVE FASTENING ANCHOR system allowsAnchor users to walk uninterrupted the entire
integrity is backed by high $7,000.000.00 liability
SHACKLE SECUREMENT IS ILLUSTRATED length of system.
insurance.Thaler Energy Absorber (TEA),
(RETROFIT APPLICATION). SEE PAGE K-3Aseparate from harness shock absorber assists in
CARABINER FOR OTHER FASTENING METHODS dissipating orOPTIONS:
reducing fall arrest forces. EASY SLID-
ER shuttle permits
Any-angleworkercornertounits
connect
availableorasdisconnect
standard. Any type
Corner Anchor at any position on cable.
securement to suitLine length
structural is unlimited.
substrate (cast-in-place, bolted,
(Any Angle) Top View of End Wall Anchor Maintenancewelded,free. etc.).
Anchor integrity is backed by
high $7,000.000.00 liability insurance.
Corner Wall With Mobile Shuttle Runner RECOMMENDED
Options: Any-angle cornerUSE: units available as stan-
Anchor K-701 EASY dard. Any type Suitable for both travel restraint and fall arrest using full body
securement to suit structural sub-
K-FARA-93-711 SLIDER (Wall PLAN VIEW
THALER ENERGY
harness and lanyard, self retracting lifeline or lifeline with rope
strate (cast-in-place, bolted, welded, etc.).
grab. Provides fall protection for servicing rooftop equipment,
With Application) ABSORBER (TEA)
roof inspection, accessing window cleaning stations and
RECOMMENDED similarUSE
EASY SLIDER Suitable for both
applications. Designed to protect up to four workers as
travel
standard. Seerestraint
K-700 andand
K-702fall arrest
system forusing
roof and overhead
Shuttle (90° Angle full body harness and lanyard, self retracting life-
applications.
Illustrated) Top View of line or lifeline with rope grab. Provides fall protec-
APPLICABLE STANDARDS:
Internal Corner tion for servicing
Thaler
rooftop
K-700 EASY
equipment, roof inspec-
SLIDER stations
conforms to all Canadian
tion, accessing window cleaning and sim- and U.S.
Anchor standards,
ilar applications. provincialto
Designed andprotect
state labor/safety
up to codes
four and
materials standards relating to anchor fabrication and
workers as standard. See K-700 and K-702 system
Montage Illustration Shows K-701 EASY SLIDER Horizontal Lifeline Fall Protection horizontal lifeline applications. Conformance includes CSA,
for roof and overhead applications.
System For Walls OML, ASME, ANSI, IWCA, OSHA, CAL OSHA, AISC, AWS, and
other references. See Thaler EASY SLIDER Horizontal Lifeline
TERMINAL END HORIZONTAL LIFELINE ANCHOR (K-FARA-93-709)
APPLICABLE STANDARDS
Primer literature for introductory data on subject of fall
Swaged End PATENT PENDING Thaler K-701 EASY SLIDER conforms to all
protection.
Canadian and U.S. standards, provincial and state
WARRANTY:
labor/safety codes and materials standards relat-
PLANNING SERVICE: 20 year warranty (lifetime
ing to anchor fabrication and on all stainless lifeline
horizontal steel) against
Thaler will provide layout drawings for the K-701 EASY SLIDER in compliance with all standards, safety regulations and local building codes.
PLANNING SERVICE applications.defects in materials and/or
Conformance manufacture
includes CSA,when OML,installed in
accordance with Thaler “Installation Instructions”.
Thaler SPECIFICATION
will provide layout drawings for the K-701 EASY SLIDER in compliance with all standards, safety regulations ASME, ANSI, IWCA, OSHA, CAL OSHA, AISC, AWS,
(Short Form):
and local building codes. and other references. See Thaler EASY SLIDER
Horizontal lifeline system: Thaler K-701 EASY SLIDER Horizontal Lifeline fall protection system for walls to [CSA-Z91-02][OSHA 1910.66, Subparts D MAINTENANCE:
and F] with: stainless steel 3/8” (10 mm) brackets welded to stainless steel base plates 5/8” x 8” x 8” (16 mm x 203 mm x 203 mm), securement Horizontal
to Lifeline Primer
Regulatory literature
authorities forthe
require introducto-
horizontal lifeline system be
SPECIFICATION (Short
suit substrate; Form)
Stainless ry 304
steel fittings (swaged end, energy absorber, double locking carabiner, end tensioner, intermediate brackets, corner pieces); data on subject
inspectedofannually
fall protection.
with inspection data (date, inspector’s
Horizontal lifeline
s.s. cable, 3/8”system: Thaler
(10 mm) dia. 7 x 19K-701 EASY
structure; [2][4]SLIDER
fully bodyHorizontal Lifeline
harnesses with fallshock
integral protection
absorber by system for walls toby[CSA-Z91-
others; manufactured Thaler Metal name and comments) recorded in the Fall Protection
Carabiner Shackle
2005
Terminal End Anchor (10 mm) dia. 7 x 19 structure; [2][4] fully body harnesses with integral shock absorber by others; manufactured by ture when installed
INSTALLATION:
movementinof accordance
the shuttle component.
with InThaler
the event of a fall, the
K-FARA-93-709 With Thaler Energy K-FARA-93-712 And EAASY SLIDER “Installation Instructions” are provided with every Thaler product. However, only Thaler or Thaler approved installers may install the the system “Installation
which
system including any affected harness, must be re-approved
Instructions”.
Thaler Metal Industries, 1-800-387-7217 (Mississauga, Ontario, Canada) or 1-800-576-1200 (New Braunfels, TX), by a professional engineer before being placed back in
Absorber (TEA). Adhesive Bolt Shuttle must
installed asbepercertified by a professionalwritten
manufacturer’s engineerinstructions.
prior to initial use. Essentially,
Provide 20 theyearK-701 EASy SLIDER
warranty Horizontal
against Lifelineinis installed
defects materials by fastening MAINTENANCE
and/oranchors to service. Inspection of caulking around wall plates should be
the wall,
manufactur e.orCaulking
other structural substrate,
of wall plates installing cable, including fittings, and sealing the wall plates to surfaces where applicable.
by others. Regulatory authorities
carried underrequire theinspection
horizontal life-
Fastening For Retrofit Applications regular roof
line system be inspected annually with inspec-
procedures.
Maintenance
CONTINUOUS
CAULKING
5/8" x 8" x 8" (16 mm x
(BY OTHERS)
GUSSET PLATES 203 mm x 203 mm)
BY OTHERS PLATES
(WHEN REQUIRED)
Shackle
2-3/4"
FOUR 5/8" (16 mm) S.S. (70 mm)
DEFORM THREADS BOLTS, LOCK WASHERS
CONTINUOUS AS PER CSA OR OSHA AND NUTS
Energy 5/16 (8 mm) GUIDELINE
2-3/4"
(70 mm)
GUSSET PLATES
BY OTHERS
(WHEN REQUIRED)
Tensioner
Bracket
S.S. CAST IN PLACE BOLTS
Available STAINLESS STEEL 3/8" (10 mm)
END BRACKET WELDED TO
TO STAINLESS STEEL 5/8" x 5" x 5"
(16 mm x 127 mm x 127 mm) PLATE
MINIMUM 6"
(152 mm)
INTERNAL CORNER ANCHOR (90° EXTERNAL CORNER ANCHOR (90° EXTERNAL CORNER ANCHOR TERMINAL END ANCHOR WITH WELDED TO BEAM (K-FARA-701) CAST-IN-PLACE
Angle Illustrated) Angle Illustrated) (Any Angle Bracket Available As TENSIONER (Inset shows Underside FASTENING (K-FARA-92-701)
Standard) of Shuttle) SECTION DETAIL
K-3A
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
K-702 EASY SLIDER TM
ROOF
ROOF SPECIALTIES
SPECIALTIES
HORIZONTAL LIFELINE
End End FALL
K-702 PROTECTION SYSTEM
EASYEASY SLIDER TM
Anchor K-702 SLIDER TM
Anchor Any-Angle
Any-Angle Corner
Corner (Overhead
HORIZONTAL Application)
LIFELINE
K-702K-702
EASYEASY Anchors Terminal End Anchor With Thaler HORIZONTAL LIFELINE
SLIDER Lifeline Anchors Terminal End Anchor With Thaler
SLIDER Lifeline Energy
Energy Absorber
Absorber (TEA)(TEA) FALLFALL PROTECTION
PROTECTION SYSTEM
SYSTEM
(Overhead
(Overhead Application)
Application)
DESCRIPTION:
DESCRIPTION The Thaler K-702, EASY SLIDERTM Horizontal Lifeline Fall
Intermediate
Intermediate Anchors
Anchors DESCRIPTION
Protection System for overhead application is a complete
The Thaler The K-702,
Thaler K-702,
EASY SLIDER EASY SLIDER
TM
TM
Horizontal Horizontal
Lifeline Lifeline
Fall pre-engineered
Protection System multi-span for flexible lifeline
overhead system consisting
application
Fall Protection of Systemend
terminal foranchors,
overhead application
intermediate anchors, isstainlessissteel
a complete a complete pre-engineered pre-engineered multi-span flexible
cable, mobile attachmentmulti-span devices (shuttle flexible
runners), in-line
lifeline lifeline
system system
consisting
fittings
consisting
(tensioner, ofenergy
terminal of terminal
endcorner
absorber,
end anchors,
anchors, fittings, etc.) and
intermediate anchors, stainless steel cable,
End Anchor
End Anchor
intermediate up to anchors,
4 shuttles. stainless
Full body harnesses steelwith cable,
6’-0” (1.8 m) long
mobilemobile shock
attachment attachment
absorbing devices devices
lanyards (shuttle
(by others)
(shuttle runners),
completes
runners), in-the assembly.in-
With Tensioner
With Tensioner line fittings (tensioner,
End and intermediate energy absorber, corner fit-base
line fittings (tensioner, energy anchors absorber, consist of a stainless
corner fit- steel
tings,and etc.)and
plate and end upshuttles.
bracket towith 4 shuttles.
two holes. Full har-
Anchors body are also har-
CloseClose Up View of Mobile Shuttle tings, etc.) up to 4 Full body
Up View of Mobile Shuttle nesses nesses with(1.8
available
with 6’-0” 6’-0” m)(1.8
with different
long m)
type long
shock shock
bases for fastening
absorbing absorbingto a variety of
Runner
Runner With Carabiner
With Carabiner Attached
Attached CONCRETE CORNICE, lanyards overhead (by orothers)
similar structures.completes All anchors the are designed to
assembly.
CONCRETE CORNICE, lanyards (byresistothers)without
completes
fracture a pull-out
theforce assembly.
of 5400
OR SOFFIT ILLUSTRATED End and End and intermediate
intermediate anchors anchors
consist consist
of a stain- of a (24.02
lbs stain-kN),
OR SOFFIT ILLUSTRATED applied in the platemost adverse direction.
MINIMUM MINIMUM less steel base plate and end bracket with two two
less steel base and end bracket with
THALER 05 11 24 23
or similar applications to [CSA-Z91-02][OSHA 1910.66, Subparts D and F][OSHA 1926.500, Subpart M (Construction)] or against K-702 defects
EASY in materials
SLIDER stainless and/or
steel cablemanufac-
only requires
THALER 05 11 24 23
or similar
bodyapplications
harnesses with integral to [CSA-Z91-02][OSHA
shock absorber (by others);1910.66, Subparts
manufactured by D andMetal
Thaler F][OSHA
Industries,1926.500,
1-800-387-7217Subpart M (Construction)]
(Mississauga, Ontario, Canada) against defects in materials and/or manufac-
Operable
Operable with: stainless steel 3/8” (10 mm) brackets welded to written
stainless steelplates
base plates 5/8” x 8” x mm
8” (16 mm x 203
with: stainless
1-800-576-1200steel 3/8” (New (10 mm)
Braunfels, brackets
TX), installed welded to stainless
as per manufacturer’s steelinstructions.
base Provide 5/8”
20 yearx 8” x 8”
warranty (16
against x 203
defects in mm x mm
materials and/or x ture when
ture when
occasional
installed installed wiping with
in accordance in accordance
a damp cloth to ensure
with Thaler with Thaler free and easy
Window,
Window, 203securement
mm),Caulkingsecurement to plates
suit substrate; Stainless steel fittings (swaged end, energy absorber, double locking cara- “Installation movement of the shuttle component. In the event of a fall, the
Instructions”.
2005
203 mm),
manufacture. to
of suit
anchors substrate; by Stainless
others. steel fittings (swaged end, energy absorber, double locking cara- “Installation Instructions”.
2005
biner, end tensioner, intermediate brackets, system including any affected harness, must be re-approved
AccessAccess biner, end tensioner, intermediate brackets, corner corner
pieces); pieces);
304 s.s.304 cable, s.s. cable,
3/8” (103/8” mm) (10dia.mm) 7 xdia.19 7 x 19 structure;
structure; [2][4] [2][4]
MAINTENANCEMAINTENANCE
by a professional engineer before being placed back in
fully body
INSTALLATION: harnesses with integral shock absorber (by others); manufactured by Thaler Metal Industries, 1-800-387- Regulatory authorities require the horizontal life-
Hatch,Hatch,
Roof Roof
fully body harnesses with integral shock absorber (by others); manufactured by Thaler Metal Industries, 1-800-387- Regulatory authorities service. Inspection require the horizontal
of caulking around plates life- should be carried
7217 (Mississauga,
“Installation Instructions” Ontario,
are provided Canada)
with every or 1-800-576-1200
Thaler product. However, (New
only Braunfels,
Thaler Metal
7217 (Mississauga, Ontario, Canada) or 1-800-576-1200 (New Braunfels, TX), installed as per manufacturer’s written line system be TX),
Industries, installed
Thaler as
approvedper manufacturer’s
installers or competent written line system be inspected annually with inspec-
inspected annually with inspec-
Area Area
Or Or
out under regular roof inspection procedures.
instructions.
installers
instructions. following
Provide Provide
Thaler
20 year 20warranty
year Instruction
Installation warranty
against against
may install defects
defects theinthe in materials
system
materials which
and/or mustand/or
be certified
manufactur manufactur
by e. e. Caulking
a professional
Caulking engineer
of anchors of anchors
prior toplates plates tion data (date, inspector’s name and com-
initial use. tion data (date, inspector’s name and com-
Other
Other Safe Safe by others.
Essentially, the K-702 EASY SLIDER Horizontal Lifeline is installed by fastening the anchors to a soffit, cornice, or other structural substrate, installing
by others. ments) recorded
ments) recorded in the Fall Protection in the Fall Protection
THALER
information. Products are typically available from stock.
CANADA:
TM EASY
TM1.800.387.7217
EASY SLIDERSLIDER
U.S.: is
is a registered
a registered
1.800.576.1200 trade
WEB:
trade of
mark mark
Thalerof Thaler
www.thalermetal.com
Metal industries
Metal info@thalermetal.com
EMAIL: industries Ltd. Patent
Ltd. Patent and design
and design pending.
pending. Canada 1-800-387-7217
1-800-387-7217 U.S. 1-800-576-1200
U.S. 1-800-576-1200 Internet:
Internet: www.thalermetal.com e-mail:e-mail:
www.thalermetal.com info@thalermetal.com
info@thalermetal.com THALER K-4 K-4K-4
Note: All Anchors are designed to resist without fracture a pull-out force of 5400 lbs (24.02 kN), applied in the most adverse direction Note: The Thaler K-700 EASY SLIDER
Horizontal Lifeline is designed to protect
30-0" (9.15 m) MAX. SPACING BETWEEN ANCHORS
3/8" (10 mm) STAINLESS STEEL
BRACKET WELDED TO 5/8" x 8" FOR SYSTEM WITH ONE ENERGY ABSORBER S.S. INTERMEDIATE BRACKET up to 2 workers against falls from height
x 8" (16 mm x 203 mm x 203 mm) AND 30'-0" TO 60'-0" (9.15 m to 18.30 m) BOLTED TO 1/2" (12 mm)
PLATE 316L STAINLESS STEEL for systems of length up to 200’-0” (61 m)
S.S. MOUNTING PLATE FOR SYSTEM WITH TWO ENERGY ABSORBERS
TENSIONER and 4 workers for systems more than 200’-
0” (61 m) long as standard.
I-BEAM MINIMUM
MIN. 6"
(152 mm) 6" (152 mm)
HORIZONTAL LIFELINE SYSTEM GALVANIZED FOUR 5/8"
(16 mm)
316L STAINLESS
SINGLE STRAIGHT LINE CABLE FOR CONSTUCTION SITE CLAMP
STEEL EASY S.S. BOLTS
SLIDER MOBILE
SHUTTLE
RUNNER
316L 3/8" (10 mm) STAINLESS CONTINUOUS
STEEL CABLE, FOUR 5/8" (16 mm) CAULKING
7 x 19 STRUCTURE S.S. CAST-IN-PLACE AROUND MOUNTING
CONTINUOUS BOLTS PLATE
CAULKING AROUND
(BY OTHERS)
PLATES (BY OTHERS)
FOUR 5/8" (10 mm)
S.S. BOLTS STAINLESS STEEL
SHACKLES
CONTINUOUS 5/16 (8 mm) SWAGED END
SOLID S.S. INTERMEDIATE SOLID STAINLESS STEEL
BRACKET BOLTED TO 1/2" FILLET WELD
INTERMEDIATE BRACKET
(12 mm) PLATE 3/8" (10 mm) S.S END BRACKET
WELDED TO 5/8" x 8" x 8"
(16 mm x 203 mm x 203 mm)
CAST-IN-PLACE (K-FARA-92-702)
THALER ENERGY
S.S. PLATE ABSORBER (TEA) SECTION DETAIL
TEMPORARY CLAMP AROUND BEAM
FLANGE (K-FARA-91-702) SECTION BOLT THROUGH (K-FARA-91-702)
DETAIL FOR CONSTRUCTION SECTION DETAIL
APPLICATIONS
2-3/4"
(70 mm)
OSHA GUIDELINE
GUSSET
PLATES
Shackle FOUR 5/8" (16 mm) S.S.
BY OTHERS
Tensioner Corner
BOLTS, LOCK WASHERS
AND NUTS (WHEN
REQUIRED)
Energy Bracket
Absorber BOLT AROUND BEAM
(K-FARA-91-702)
TERMINAL END ANCHOR WITH SECTION DETAIL
ENERGY ABSORBER AND INTERMEDIATE ANCHOR
SWAGED END CONSTRUCTION CLAMP (Temporary) TERMINAL END ANCHOR WITH TERMINAL END ANCHOR WITH 5/8" x 8" x 8" (16 mm x
203 mm x 203 mm)
TENSIONER (Temporary. View From Above) TENSIONER (Temporary. View From Below) S.S. PLATE
K-3A
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice. Please
Please be be advised
advised Thaler products
Thaler products may undergo
may undergo improvements
improvements from from
time time to time
to time and and are subject
are subject to change
to change without
without notice.
notice.
ROOF SPECIALTIES
ROOF SPECIALTIES
ROOF SPECIALTIES
K-703 EASY SLIDER TM
K-703 EASY
K-703HORIZONTALSLIDER
EASY SLIDER
TM
LIFELINE
TM
12-5/8" (321 mm )
GROMMET THALER SEALSJ-37 NEW- THALER ENERGY Prominent Features: Designed to protect up to 2
Vertical Attached
Lifelines To (byHorizontal
others) Lifeline
OR STAINLESS
ILLUSTRATED STEEL)(BUR)
the most againstfree systemdirection.
adverse allows users to walk uninterrupted the entire
STANDARD STACK JACK ABSORBER (TEA). workers falls from
INVERTED ROOF ThalerheightEnergy for systems(TEA), of
12-5/8" (321 mm )
length of system. Absorber
THALERFLASHING
SJ-37 NEW- (ALUMINUM, TWO TEAS
THALER ENERGY REQUIRED Prominent Features: Designed to standard
protect up(pre- toseparate
2 from
Attached To Horizontal Lifeline COPPER ORJACK STAINLESS STEEL)
ILLUSTRATED (BUR)
FOR 80'-0"(TEA).
ABSORBER (24.4 m) POST length up harness shock (24.4
to 80’-0” absorber, m)assists as in dissipating or reducing fall
End Anchor STANDARD
FLASHING (ALUMINUM,
STACK
SPACING,
TWO TEAS REQUIRED ONE TEA FOR
workers
vents against
users from falls
falling frommore height
than for
6’-0”
arrest forces. EASY SLIDER shuttle permits worker to connect
systems
or 1.8 m). of
With Tensioner COPPERCONVENTIONAL
OR STAINLESS ROOF STEEL) FOR 60'-0"
80'-0"(18.3
(24.4m) m)SPACING
POST length
Hands up free orto 80’-0” allows
system
disconnect at(24.4 m) as
users
any position ontostandard
walkCondensation
cable. uninter- (pre- free and
End Anchor ILLUSTRATED (BUR) SPACING, ONE TEA FOR vents
rupted users
the from
entirefalling
maintenance freemore
length of system.
(attractive, than neat 6’-0”
Thaler orEnergy
flashing 1.8
neverm). needs
With Tensioner CONVENTIONAL ROOF 60'-0" (18.3 m) SPACING Hands
Absorber free system
(TEA),
caulking. allows
separate
See Thaler EPDM users
from to
harness
Flashing walk
Seals uninter-
shock Anchor
literature.
ILLUSTRATED (BUR) rupted
absorber, theintegrity
entireislength
assists in
backed ofhigh
dissipating
by system. Thaler liability
or reducing
$7,000.000.00 Energy fallinsurance.
Absorber
arrest forces. (TEA), EASYseparateSLIDER shuttle frompermits harness worker shock to
connect or
absorber, OPTIONS:
disconnect
assists in dissipatingat any position or reducing on cable. fall
Condensation
arrest forces. Any typeEASYsecurement
freeSLIDER and to suit
shuttle structural
permitssubstrate
maintenance worker freeto
NOTE: BOLT (attractive,
connect or(cast-in-place,
neat flashing
disconnect bolted, welded,
atnever
any etc.). PVC
needs
position oncoated
caulking.
cable. flashing deck
Worker Attached AROUND BEAM See Thalerflange
Condensation EPDM for PVC roof membrane,
Flashing
free andSeals
bituminousAnchor
literature.
maintenance
painted flashing
free
With Rope Grab To NOTE:ANCHOR BOLT integrity isdeck
(attractive, backed flange by
neat aluminum,
for BUR
flashing highand ModBit roof membrane.
$7,000.000.00
never liabilityFlashing is
EMBED DECK FLANGE 18 GA. GALVANIZED
SECUREMENT insurance. available copper orneeds
stainless caulking.
steel.
Suspension Worker Attached
Lifeline (by others)
IN LAYER OF PLASTIC CLOSURE PLATE SCREW AROUND BEAM See Thaler EPDM Flashing Seals literature. Anchor
CEMENT (BUR) ILLUSTRATED.
ANCHOR Options:is Any type by securement to suit structural
Line With Rope Grab To EMBED DECK FLANGE
FASTENED TO STEEL DECK
18 GA. GALVANIZED SEE SECTION “I”
integrity backed
RECOMMENDED high
substrate (cast-in-place, bolted, welded, etc.).
USE: $7,000.000.00 liability
Suspension IN LAYER 5/8"OF x 8" x 8" (16 mm x
PLASTIC EPDM PLATE BASE SEAL SECUREMENT insurance. Suitable for both travel restraint and fall arrest using full body
End Anchor With Tensioner Lifeline (by others) CEMENT203 (BUR)mm x 203 mm) PLATE
CLOSURE
BONDED TO METAL SLEEVE
SCREW (FALL ARREST
ILLUSTRATED. PVC coated
Options: Any
harness
flashing
type
deck
securement
and lanyard,
flange forlifeline
self retracting
PVCorroof
to suit structural lifeline with rope
Line GUSSET PLATES
FASTENED TO STEEL DECK
(SEE THALER EPDM FLASHING ROOF
SEE SECTION “I”
ANCHORS) membrane, bituminous
substrate grab. Provides fall protection
(cast-in-place,
painted
bolted, for flashing
window
welded,
deck servicing
cleaning,
etc.).
5/8" x 8" xBY 8"OTHERS
(16 mm x SEALS
EPDM BASE SEAL LITERATURE) SECTION OF flange for BURequipment,and ModBit roof membrane.
Illustration Shows K-703 EASY SLIDER Horizontal Lifeline Fall Protection System For Single Span Application 203 mm x(WHEN (FALL ARREST PVC coated rooftop flashing deck roof inspection,
flange for accessing
PVC window roof
End Anchor With Tensioner 203 mm) PLATE
REQUIRED) BONDED FOURTO 5/8"METAL(16 mm) SLEEVE
S.S.
ROOF
MANUAL
ANCHORS)
FOR Flashing iscleaning available stations aluminum,
andpainted copper oronstain-
similar applications flat or low slope
GUSSET PLATES
(SEEBOLTS, THALER LOCK EPDM FLASHING
WASHERS OTHER FASTEN- membrane, bituminous
less steel.roofs. Designed to protect up to two workers (as standard) on
flashing deck
BY OTHERS
AND NUTS
SEALS LITERATURE) SECTION
ING METHODS OF flange for BUR and ModBit roof membrane.
Illustration Shows K-703 EASY SLIDER Horizontal Lifeline Fall Protection System For Single Span Application MANUAL FOR RECOMMENDED system. USE
(WHEN REQUIRED) FOUR 5/8" (16 THREADS
DEFORM mm) S.S. Flashing
Suitable isfor available
both travel aluminum, restraint copper and fallorarrest stain-
60'-0" (18.3 m) MAX. SPACING BETWEEN ANCHORS BOLTS, AS LOCK
PER CSA WASHERS
OR OSHA OTHER FASTEN- less steel.
FOR SYSTEM WITH ONE ENERGY ABSORBER AND GUIDELINE
NUTS (2 THREADS ING METHODS using full body
APPLICABLE harness and
STANDARDS: lanyard, self retract-
TYPE 304 3/8" (10 mm) 80'-0" (24.4 m) MAX. SPACING MINIMUM) RECOMMENDED
ing lifelineThaler or lifeline
K-703USEEASYwith SLIDERrope grab. conforms Provides
to all Canadian fall and U.S.
FOR SYSTEM WITH TWO ENERGY ABSORBERS DEFORM THREADS
STAINLESS Suitable
protection for forboth
standards,window travel
provincial restraint
and state
cleaning, and fall
labor/safety
servicing arrest
codes
rooftop and
STEEL CABLE, 60'-0" (18.3 m) MAX. SPACING BETWEEN ANCHORS AS PER CSA OR OSHA
using full body
equipment, materials
roof harness
standards
inspection, and
relating lanyard,
to anchorself
accessing retract-
fabrication
window and
SHACKLE 7 x 19 STRUCTURE FOR SYSTEM WITH ONE ENERGY ABSORBER
80'-0" (24.4 m) MAX. SPACING
TERMINAL END HORIZONTAL LIFELINE GUIDELINE (2ANCHOR THREADS (K-FARA-13-717) ing horizontal
lifeline stations
cleaning or lifeline lifeline
and with applications.
ropeapplications
similar Conformance
grab. Provides includes
on flat fall CSA,
TERMINAL END HORIZONTAL LIFELINE ANCHOR (K-FARA-13-717)
TYPE 304 3/8" (10 mm) MINIMUM)
STAINLESS FOR SYSTEM WITH TWO ENERGY ABSORBERS PATENT PENDING protection
or low slope OML, ASME,Designed
forroofs.
window ANSI, IWCA, to
cleaning, OSHA, CAL OSHA,
servicing
protect AISC,
up rooftop
to twoAWS, and
STEEL CABLE, other references. See Thaler EASY SLIDERwindow Horizontal Lifeline
PATENT
of a fall,PENDING workers (as
equipment, standard)
roof on
inspection, system. accessing
SHACKLE 7 x 19 STRUCTURE TERMINAL
movement ENDcomponent.
of the shuttle HORIZONTAL In the event LIFELINE the ANCHOR
system including (K-FARA-13-717)
any affected harness, must be
APPLICABLE
cleaning Primer literature for introductory data on subject of fall
STANDARDS
stations and similar applications on flat
TENSIONER re-approved by a professional engineer before being placed back in service. protection.
TYPE 316L STAINLESS
LANYARD, SELF RETRACTING PATENT PENDING orThaler
low slope K-703 roofs. EASY Designed SLIDER toconforms protect uptoto two all
STEEL SHUTTLE
LIFELINE OR LIFELINE WITH ROPE PLANNING
PLANNING SERVICE: SERVICE
GRAB BY OTHERS IS ATTACHED
Thaler willtheprovide layout drawings Canadian
workers (as and U.S. on
standard) standards,
system. provincial and
TO SHUTTLE
Thaler
movement willofprovide layout drawings
shuttle component. for the K-703 Inforthetheevent
EASY K-703
SLIDERofEASY SLIDER
inacompliance
fall, the with in compliance
system all standards,
including withany
safety all standards,
regulations
affected safety
and harness,
local regulations
building must codes.be WARRANTY:
state labor/safety
APPLICABLE codes and materials stan-
THALER ENERGY ABSORBER (TEA) TENSIONER and local
re-approved by a building
professionalcodes.engineer before being placed back in service. 20 STANDARDS
year warranty (lifetime on all stainless steel) against leaks,
TYPE 316L STAINLESS
NOTE: UP TO 2LANYARD,
PERSONNEL SELF RETRACTING
PERMITTED
SPECIFICATION
SPECIFICATION (Short (Short
Form): Form) dards relating
Thaler K-703condensation
to
EASY anchor
andSLIDER
fabrication
defects inconforms
and hori-
materials and/or tomanufacture
all
ON SYSTEM AS LIFELINE
STANDARD OR LIFELINE WITH ROPE PLANNING SERVICE zontal lifeline applications.
INVERTED ROOF STEEL SHUTTLE GRAB BY OTHERS IS ATTACHED
Thaler Horizontal
Horizontal
will providelifeline lifeline
system:
layout system:
drawings Thaler
Thaler K-703 for EASYK-703
the SLIDER
K-703EASY SLIDER
Horizontal
EASY Horizontal
Lifeline
SLIDER in Lifeline
fallcompliance
protection fall
system withprotection
to [CSA-Z91-02][OSHA
all standards, systemsafety to
1910.66, Subparts D and F] Canadian
[CSA-Z91-02][OSHA
regulations whenand U.S.
installed accordance Conformance
instandards, provincial
with Thaler “Installation and Instruct-
2005
ROOF INVERTED ROOF Horizontal system: Thaler K-703 SLIDER Horizontal Lifeline fall to [CSA-Z91-02][OSHA literature Regulatory
for introductory authorities datarequire on subject of lifeline
fall
ANSI,theIWCA, horizontal OSHA, system be
2005
ROOF ish 1100-0T
flange] [PVC coated alloy
deck aluminum]
flange]; [.032” (0.831
manufactured by Thaler Metal24Industries,copper]
1-800-387-7217 (0.79 mm) 22Ontario,
(Mississauga, ga. Type
Canada) stainless
1-800-576-1200 steel] literature for introductory
shows adhesive bolt securement ble locking carabiner, shuttles, end tensioner); Type 304 s.s. cable, 3/8” (10 mm) dia. 7 x 19 structure); [1][2] full body against K-703
leaks, EASY SLIDER data
condensation stainless
and onsteelsubject
defects cable only
inof fall requires
ish 1100-0T
warranty alloy aluminum]
against leaks, [.032” (0.831 mm)
condensation and 24 oz. copper]
defects in materials [.031” and/or (0.79 mm) 22 ga.
manufactur e. Type 304 stainless steel] to 20 year warranty
ions”. system including (lifetime any onaffectedall stainless
harness, must steel) be re-approved
INSTALLATION: against by a professional
leaks, condensation engineerand before being placed
defects in back in
Essentially, the K-703 EASY SLIDER Horizontal Lifeline is installed by fastening the anchor posts on the roof structural substrate, installing flashing, and
warranty must
cable, against
be certified
including leaks, condensation
fittings. by a professional and defectsprior
engineer in materials
to initial use. and/or manufactur
Essentially, the K-703e. EASY SLIDER Horizontal Lifeline is ions”. tion data (date, inspector’s name and com-
installed by fastening the anchor posts on the roof structural substrate, installing flashing, and cable, including fittings. MAINTENANCE ments) recorded in the Fall Protection
INSTALLATION
FOUR 5/8" (16 mm)
Recommended Layout: Maximum spacing between anchor posts is 80’-0” (24.4 m) for system with two energy Maintenance
Regulatory Log book.
authorities Apartthe
require from this require-
horizontal life-
ADHESIVE ANCHOR BOLTS K-703 Horizontal Lifeline Single Span Application “Installation
Recommended Instructions”
Layout: Maximumare provided spacing between with every Thaler
anchor posts product.
is 80’-0” (24.4 m) However,
for system with onlytwo Thaler
energy Metal
absorbers, Industries,
and 60’-0” Thaler (18.3 m) for
absorbers, and 60’-0” (18.3 m) for system with one energy absorber. Horizontal lifeline should not be located closer ment,
line systemthe be K-703 inspected EASY SLIDER annually stainless
with inspec- steel
(RETROFIT APPLICATION) approved
system with installers
one energy or competent
absorber. Horizontal installers
lifelinefollowing
should not be Thaler
locatedInstallation
closer than 6’-6” Instructions
(1.98 m) from may anyinstall
roof edge. theFor the system
minimum which cable only requires occasional wiping
clearance with a
than
mustrequired
be 6’-6” (1.98am)
certified
below theby
from any roof edge. prior
professional
level of the horizontal engineer
For minimum
lifeline, see page K-1. to Consult
initial use. clearance
Essentially,
with Thaler
required
for layout the belowEASY
K-703
recommendations.
the level
SLIDER of Horizontal
the horizontal Lifeline is tion
lifeline, data (date, inspector’s name and com-
damp cloth to ensureinfreethe and Fall easy Protection
Note: For Minimum Fall Clearance Required Below System See Page K-1 see page K-1. Consult with Thaler for layout recommendations.
installed by fastening the anchor posts on the roof structural substrate, installing flashing, and cable, including fittings. (continued on left) ments) recorded
Ordering and
Recommended Availability:
Layout: Maximum Available spacing throughout
between North America.
anchor posts Contact
is of80’-0” Thaler (24.4for m) list offordistributors
system andtwo
with currentenergy cost Maintenance Log book. Apart from this require-
K-703 Horizontal Lifeline Single Span Application Ordering and Availability: Available throughout North America. Contact Thaler for list distributors and current cost information. Products are typically
60’-0” (18.3 m) for system with one energy absorber. Horizontal lifeline should not be located closer ment, the K-703 EASY SLIDER stainless steel
THALER
absorbers,information.
available and from stock.
TM EASY SLIDER is a registered trade mark of Thaler Metal industries Ltd. Patent and design pending
than 6’-6” (1.98
Canada m) from any U.S.
1-800-387-7217 roof edge.
1-800-576-1200For minimum clearance
Internet: required below thee-mail:
www.thalermetal.com the horizontal lifeline, cable only requires occasional wiping with
level ofinfo@thalermetal.com
damp cloth to ensure free and easy
K-5a
Note: For Minimum Fall Clearance Required Below System See Page K-1 see page K-1. Consult with Thaler for layout recommendations.
Ordering and Availability: Available throughout North America. Contact Thaler for list of distributors and current cost (continued on left)
THALER
information.
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com Canada 1-800-387-7217 U.S. 1-800-576-1200 Internet: www.thalermetal.com e-mail: info@thalermetal.com K-5 K-5
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
K-700 EASY SLIDER HORIZONTAL LIFELINE K-701 EASY SLIDER HORIZONTAL LIFELINE K-702 EASY SLIDER HORIZONTAL LIFELINE EASY SLIDERTM
HORIZONTAL LIFELINES FALL
FALL PROTECTION SYSTEM (Roof Application) FALL PROTECTION SYSTEM (Wall Application) FALL PROTECTION SYSTEM (Overhead PROTECTION SYSTEM
3/8” (10 mm) Application) COMPONENTS
Thickness End
Anchor Bracket
with two 3/4” (19
mm) holes welded
to top plate of HSS K-703 EASY SLIDER HORIZONTAL
3/8” (10 mm)
anchor post
Thickness End Anchor
LIFELINE FALL PROTECTION
Bracket with two 3/4” SYSTEM (Single Span Application)
(19 mm) holes, welded
to plate
Intermediate Bracket
bolted to plates
Side View
Note: This horizontal lifeline specification, with minor editing, has been written as a separate sectionof work. Alternatively, the appro-
priate clauses may be incorporated as part of a roofing specification in regions where this feature is desired.
PART 1: GENERAL
1.01 SECTION INCLUDES
1.03 REFERENCES
Canadian
K-7
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
HORIZONTAL LIFELINE
FALL PROTECTION SYSTEM
SPECIFICATION
A. CGSB-51-GP 46MP (Manual for Installers of Spray Urethane Foam Thermal Insulation).
United States
C. OSHA 1910.66, SubPart F (Powered Platforms, Manlifts, and Vehicle-Mounted Work Platforms).
E. CAL OSHA, Title 8, Section 3291(f), Article 5. Window Cleaning (General Industry Safety Order, California Code of Regulations),
Article 6, Powered Platforms for Exterior Building Maintenance, Article 23, Suspended Scaffolds (Construction), and Article 24,
Fall Protection (construction).
A. ASME A120.1-1996 (Safety Requirements for Powered Platforms for Building Maintenance).
C. ASTM A123 (Standard Specification for Zinc Coating Hot Dip Galvanizing of Iron and Steel Products).
K-8
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
HORIZONTAL LIFELINE
FALL PROTECTION SYSTEM
SPECIFICATION
A. Design horizontal lifeline fall protection system to provide for safe execution of window washing or other suspended maintenance
operations [including travel restraint].
B. Co-ordinate work of this Section with [Section 07500 - Membrane Roofing], to provide continuous waterproof protection.
C. Design anchors to resist without fracture a pull-out force of 5400 lbs (24.03 kN), applied in the most adverse direction.
1.05 SUBMITTALS
A. Manufacturer’s descriptive literature for each product, including section or other type details.
C. Shop drawings and samples, when required, in accordance with Section [01300]. Shop drawings to show roof layout indicating
location and spacing of anchors and horizontal lifeline, including dimensions, detail drawings of securement to structure, design details,
and similar data. Drawings to bear stamp of Professional Engineer licensed in the [Province] [State] in which the project is located.
D. Upon completion of project, provide Owner with Log Book for mandatory annual inspection.
E. Upon completion of project, provide Owner with roof plan showing layout of safety anchor system.
A. Horizontal lifeline fall protection system manufacturer to have minimum 5 years documented experience in the design and fabrication
of fall protection systems.
A. Warrant products installed under this section of work to be free of leaks, condensation and defects in materials and/or manufacture,
as applicable, for a period of 20 years when installed in accordance with the manufacturer’s written instructions.
K-9
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
HORIZONTAL LIFELINE
FALL PROTECTION SYSTEM
SPECIFICATION
PART 2: PRODUCTS
2.01 MANUFACTURER
A. Provide products as manufactured by Thaler Metal Industries, 1-800-387-7217 (Mississauga, Ontario, Canada) or 1-800-576-1200 (New Braunfels,
TX) or provide equal products by another manufacturer approved in advance by the [Architect], based upon:
1. 20 year warranty against leaks, condensation and defects in materials and/or manufacture, as applicable;
2. structural rating for up to 12,000 lbf (53.28 kN) strength for anchors equipped with forged round eye;
3. structural integrity backed by $7,000,000.00 liability insurance;
4. injection molded urethane insulation to CGSB-51-GP 46MP and ASTM C1029-90, as applicable;
5. air barrier flashing design using EPDM seals only complying with CSA B272-93 flashing standard;
6. maintenance free design;
7. materials and sizes options, and thickness;
8. treated flashing deck flange, as applicable;
9. written installation instructions.
K-700 EASY SLIDERTM Horizontal Lifeline Fall Protection System (Roof Application)
A. Horizontal lifeline system (roof application): Thaler K-700 EASY SLIDER Horizontal Lifeline fall protection system to [CSA-Z91-02][OSHA 1910.66,
Subparts D and F] with: 3-1/2” (89 mm) dia. urethane insulated HSS anchor posts, wall thickness 1/4” (6 mm), hot dipped galvanized ASTM 500, 12”
(305 mm) high, welded and bolted to 1/2” x 8” x 8” (12 mm x 203 mm x 203 mm) 44W base plate, securement to suit substrate; Stainless steel fittings
(swaged end, energy absorber, double locking carabiner, shuttles, end tensioner, intermediate brackets, corner pieces); Type 304 s.s. cable 3/8” (10 mm)
dia. 7 x 19 structure); [2][4] full body harnesses with integral shock absorber (by others); [SJ-34, 7” (178 mm) high] [ SJ-35 13” (330 mm) high]
New-Standard STACK JACK Flashing of [.064” (1.6 mm) mill finish 1100-0T alloy aluminum] [.032” (0.831 mm) 24 oz. copper] [.031” (0.79 mm) 22 ga.
Type 304 stainless steel] to CSA B272-93, with EPDM Triple Pressure Grommet Top Seal and EPDM Base Seal and [bituminous painted deck flange] [PVC
coated deck flange].
K-701 EASY SLIDERTM Horizontal Lifeline Fall Protection System (Wall Application)
A. Horizontal lifeline system (wall application): Thaler K-701 EASY SLIDER Horizontal Lifeline fall protection system for walls to [CSA-Z91-02][OSHA
1910.66, Subparts D and F] with: stainless steel 3/8” (10 mm) brackets welded to stainless steel base plates 5/8” x 8” x 8” (16 mm x 203 mm x 203 mm),
securement to suit substrate; stainless steel fittings (swaged end, energy absorber, double locking carabiner, shuttles, end tensioner, intermediate
brackets, corner pieces); Type 304 s.s. cable, 3/8” (10 mm) dia. 7 x 19 structure; [2][4] fully body harnesses with integral shock absorber (by others).
K-702 EASY SLIDERTM Horizontal Lifeline Fall Protection System (Overhead Application)
A. Horizontal lifeline system (Overhead Application): Thaler K-702 EASY SLIDER OverheadHorizontal Lifeline fall protection system for overhead or
similar applications to [CSA-02][OSHA 1910.66, Subparts D and F][OSHA 1926.500, Subpart M (Construction)] with: stainless steel 3/8” (10mm)
brackets welded to stainless steel base plates 5/8” x 8” x 8” (16 mm x 203 mm x 203 mm), securement to suit substrate; stainless steel fittings (swaged
end, energy absorber, double locking carabiner, end tensioner, shuttles, intermediate brackets, corner pieces); Type 304 s.s. cable, 3/8” (10 mm) dia. 7 x 19
structure; [2][4] fully body harnesses with integral shock absorber (by others).
K-10
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
HORIZONTAL LIFELINE
FALL PROTECTION SYSTEM
SPECIFICATION
K-703 EASY SLIDERTM Horizontal Lifeline Fall Protection System (Single Span Application)
A. Horizontal lifeline system (Single Span Application): Thaler K-703 EASY SLIDER Horizontal Lifeline fall protection system to [CSA-Z91-02][OSHA
1910.66, Subparts D and F] with: 3-1/2” (89 mm) dia. urethane insulated HSS anchor posts, wall thickness 1/4” (6 mm), hot dipped galvanized ASTM
500, 12” (305 mm) high, welded and bolted to 1/2” x 8” x 8” (12 mm x 203 mm x 203 mm) 44W base plate, securement to suit substrate; stainless
steel fittings (swaged end, energy absorber, double locking carabiner, shuttles, end tensioner); Type 304 s.s. cable, 3/8” (10 mm) dia. 7 x 19 structure);
[1][2] full body harnesses with integral shock absorber (by others); [SJ-34 (uninsulated) or SJ-37 (insulated), 7” (178 mm) high] [SJ-35 (uninsulated) or
SJ-38 (insulated), 13” (330 mm) high] New-Standard STACK JACK Flashing of [.064” (1.6 mm) mill finish 1100-0T alloy aluminum] [.032” (0.831 mm)
24 oz. copper] [.031” (0.79 mm) 22 ga. Type 304 stainless steel] to CSA B272-93, with EPDM Triple Pressure Grommet Top Seal and EPDM Base Seal
and [bituminous painted deck flange] [PVC coated deck flange].
PART 3: EXECUTION
3.01 EXAMINATION
A. Report to the Contractor in writing, defects of work prepared by other trades and other unsatisfactory site conditions. Verify site dimensions.
Commencement of work will imply acceptance of prepared work.
Note: Review design criteria for tapered roof insulation systems if necessary for specific projects.
B. For roofs employing tapered insulation systems, height adjustments may be necessary i.e. ensure centre line of cable anchor bracket is
minimum 9” (229 mm) above roof surface.
3.02 PREPARATION
A. For re-roofing or retrofit work, remove existing roof assembly as necessary to allow for installation of roof anchors.
B. In the event of structural deficiencies, deck corrosion or deterioration, ensure that a structural engineer has assessed and approved all
surfaces upon which the work of this Section depends. Institute repairs and/or reinforcement where necessary.
C. If necessary, protect building interior and contents against ingression of water, dust, debris or other material.
D. Where possible and as directed by Roofing Consultant, reuse any salvageable materials and restore roofing system to match original.
3.03 INSTALLATION
1. Install anchors or equipment in accordance with manufacturer’s printed instructions, shop drawings and as specified.
2. Ensure anchors or equipment is installed under the direct supervision of a Professional Engineer [and Roofing Consultant].
3. Where necessary, provide protection against deterioration due to contact of dissimilar materials.
4. Where bolting is used for fastening anchors, no fewer than two threads is to be exposed and the nut is to be positively locked by deforming
threads, welding, pinning or equivalent method.
K-11
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com
Please be advised Thaler products may undergo improvements from time to time and are subject to change without notice.
ROOF SPECIALTIES
HORIZONTAL LIFELINE
FALL PROTECTION SYSTEM
SPECIFICATION
B. Flashing
BUR
2. Set flashing deck flange in layer of plastic cement and flash in with 3 overlapping layers of felt flashing.
Modified Bitumen
3. Torch membrane until bitumen is fluid and set flashing deck flange into fluid. Flash in flange with two overlapping layers of ModBit and
seal with asphalt sealer. Do not overheat (melt) EPDM Base Seal.
Single Ply
4. Set deck flange in layer of membrane adhesive and extend single ply up sleeve to highest elevation possible and clamp membrane to STACK JACK
Flashing.
Note: For PVC membrane, specify PVC coated flashing; weld roofing to deck flange using PVC torch
6. Structural adequacy of [roof][wall][soffit] or other part of the building on which the support system is placed shall be verified by a
professional engineer before installing horizontal lifeline.
B. All anchor work to be inspected by a qualified testing agency, Professional Engineer [and Roof Consultant] upon completion of work.
Note: Field testing of roof, wall or overhead anchor products is not required. Only the field testing of adhesive fasteners is required. In
rare instances where adhesive fasteners must be tested after roof anchors have been roofed in, consult a Professional Engineer for
calculation of the load requirement prior to testing.
A. Verify that all manufactured units have been installed in accordance with specifications and details, and will function as intended.
Adjust any items where necessary to ensure proper operation.
B. Provide necessary documentation certifying system is acceptable for service (Engineer’s Certificate of Acceptance).
3.06 CLEANING
A. Clean manufactured units using materials and methods approved by manufacturer. Do not use cleaners or techniques which could
impair performance of the roofing system.
End Of Section
K-12
CANADA: 1.800.387.7217 U.S.: 1.800.576.1200 WEB: www.thalermetal.com EMAIL: info@thalermetal.com