Professional Documents
Culture Documents
Huawei Test Case Description - DC-HSDPA (TC-WRAN12.0-UAE DC-V1.0-20100427)
Huawei Test Case Description - DC-HSDPA (TC-WRAN12.0-UAE DC-V1.0-20100427)
DC-HSDPA
Website: E-MAIL:
Huawei Technologies Co., Ltd.
http://support.huawei.com support@huawei.com
Email: support@huawei.com
All other trademarks and trade names mentioned in this document are the property of their
respective holders.
Notice
The information in this document is subject to change without notice. Every effort has been
made in the preparation of this document to ensure accuracy of the contents, but all
statements, information, and recommendations in this document do not constitute the
warranty of any kind, express or implied.
Huawei Test Cases Description
DC-HSDPA Internal use
Table of Contents
T01 Basic Feature........................................................................................................................................1
T01-01 Compatibility..........................................................................................................................1
T01-0101 DC-HSDPA service setup successfully with SRB on EDCH/DCH..........................1
T01-02 Service Bearer........................................................................................................................4
T01-0201 DC-HSDPA Service setup successfully with 16QAM on Primary and secondary
carriers.........................................................................................................................................4
T1 Basic Feature
T1.1 Compatibility
Global ID
DC-HSDPA A-0101
Priority
High1
Objective
During DC-HSDPA Service setup, the RNC selects appropriate channels to carry SRB. It is
based on the UE capability, cell capability, and service parameters to optimize the utilization
of cell resources and ensure the QoS.
The case verifies the system supports DC-HSDPA Service setup successfully with SRB
carried on EDCH/DCH.
Network diagram
Standard networking of acceptance, for details of standard networking, refer to Appendix 1.
(NE: RNC1, NodeB1, CELL_A11, CELL_A12 and they are DC cell group)
Prerequisites
1. WCDMA system is in normal operation.
2. DC-HSDPA CAT24 UE is subscribed to the interactive service at 5760 kbps (UL) and
43200 kbps (DL) on the HLR.
3. CELL_A11 and CELL_A12 supports HSUPA, 64QAM and DC-HSDPA function.
4. UE is in idle mode and camps on the CELL_A11.
5. Set the SRB channel type to EDCH/DCH and SRB channel type RRC effect flag to true
on RNC1 as follows:
SET UFRCCHLTYPEPARA: SrbChlType=HSUPA, SrbChlTypeRrcEffectFlag=TRUE;
6. The corresponding Uu, Iub, Iu tracing are created in the BSC6900 Local Maintenance
Terminal of RNC1.
Procedure Expected result
Remarks
1. Check RNC license "HSPA + Downlink 42 Mbit/s Per User" is "ON" on RNC1 through
the MML command: DSP LICENSE.
2. Local Cell Number Support DL 64QAM and DC-HSDPA on NodeB through the MML
command: DSP LICENSE.
3. Logical Cell support DL 64QAM and DC-HSDPA through the MML command: DSP
UCELLCHK.
4. Before the verification, backup the configuration.
5. Related protocol specifications are as follows:
3GPP TS 25.211: Physical channels and mapping of transport channels onto physical
channels (FDD)
3GPP TS 25.306: UE Radio Access capabilities
3GPP TS 25.321: Medium Access Control (MAC) protocol specification
3GPP TS 25.331: Radio Resource Control (RRC) Protocol Specification
6. Related Huawei feature specifications are as follows:
WRFD-010696 DC-HSDPA
WRFD-010683 Downlink 64QAM
T1.2.1 DC-HSDPA Service setup successfully with 16QAM on Primary and secondary
carriers
Global ID
DC-HSDPA A-0201
Priority
High1
Objective
When the service is setup, RNC selects appropriate channels and modulation method to carry
it. That is based on the UE capability, cell capability, and service parameters to optimize the
utilization of cell resources and ensure the QoS.
The case verifies the system supports DC-HSDPA with16QAM modulation method.
Network diagram
Standard networking of acceptance, for details of standard networking, refer to Appendix 1.
(NE: RNC1, NodeB1, CELL_A11, CELL_A12 and they are DC cell group)
Prerequisites
1. WCDMA system is in normal operation.
2. DC-HSDPA CAT24 UE is subscribed to the interactive service at 5760 kbps (UL) and
43200 kbps (DL) on the HLR.
3. CELL_A11 and CELL_A12 supports DC-HSDPA function
4. DC-HSDPA CAT24 UE is in idle mode and camps on the CELL_A11.
5. Set the modulation method to 16QAM on RNC1 as follows:
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_64QAM_SWITCH-0;
6. The corresponding Uu, Iub, Iu tracing are created in the BSC6900 Local Maintenance
Terminal of RNC1.
Procedure Expected result
Remarks
1. Check RNC license "HSPA + Downlink 42 Mbit/s Per User" is "ON" on RNC1 through
the MML command: DSP LICENSE.
2. Local Cell Number Support DL 16QAM and DC-HSDPA on NodeB through the MML
command: DSP LICENSE.
3. Logical Cell support DL 16QAM and DC-HSDPA through the MML command: DSP
UCELLCHK.
4. Before the verification, backup the configuration.
5. Related protocol specifications are as follows:
3GPP TS 25.211: Physical channels and mapping of transport channels onto physical
channels (FDD)
3GPP TS 25.306: UE Radio Access capabilities
3GPP TS 25.321: Medium Access Control (MAC) protocol specification
3GPP TS 25.331: Radio Resource Control (RRC) Protocol Specification
6. Related Huawei feature specifications are as follows:
WRFD-010696 DC-HSDPA
WRFD-010629 DL 16QAM Modulation
Radio Bearers Parameter Description
7. Operation Guide
(1) Check the HSDPA function of cell is active through the MML command: DSP UCELL.
(2) Check the 16QAM function, downlink L2 Enhanced function and DC-HSDPA function
are active through the MML command: LST UCORRMALGOSWITCH.
(3) Check the164QAM function, downlink L2 Enhanced function and DC-HSDPA function of
the two cells are active through the MML command: LST UCELLALGOSWITCH.
(4) Check the code resource of cell is enough through the MML command: LST
UCELLHSDPA.
(5) Check the HSUPA function of cell is active through the MML command: DSP UCELL.
(6) Check UE supports DC-HSDPA function through the "hsdsch-physical-layer-category-
ext2" IE in the RRC_RRC_CONNECT_SETUP_CMP message.
(7) Check "DL BE traffic threshold on HSDPA " is default value on RNC1 through the MML
command: LST UFRCCHLTYPEPARA.