Professional Documents
Culture Documents
RTU Station
Release Notes
*B0780SB* *N*
B0780SB, Rev N
May 2020
https://www.se.com
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished
for informational use only. No part of this guide may be reproduced or transmitted in
any form or by any means (electronic, mechanical, photocopying, recording, or
otherwise), for any purpose, without the prior written permission of Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide
or its content, except for a non-exclusive and personal license to consult it on an "as is"
basis. Schneider Electric products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational
content of this material or consequences arising out of or resulting from the use of the
information contained herein.
RTU Station Release Notes
Table of Contents
Preface ...............................................................................................................5
Revision Information.........................................................................................5
Related Documents..........................................................................................5
Global Customer Support .................................................................................6
We Welcome Your Comments...........................................................................6
Chapter 1: Functionality and Compatibility ...................................................7
RTU Software ..................................................................................................7
SALL Support Files ..........................................................................................9
Superseded Versions .....................................................................................10
Chapter 2: Changes Since Previous Release ............................................ 11
Defects Corrected .......................................................................................... 11
Chapter 3: Known Problems and Limitations .............................................14
Chapter 4: Validation and Verification Statement ......................................17
B0780SB, Rev N 3
n k
Bla
ef t
y L
all
io n
n t
Inte
ge
P a
h i s
T
Preface RTU Station Release Notes
Preface
This document accompanies a major release of the EcoStruxure™ Foxboro SCADA
RTU Station software, identified as part number SY-1101211_K (built from internal
baseline 17.0.0). The Foxboro RTU Station is used for configuring Foxboro remote
devices and the RTU50. This document describes:
• Changes since the previous release of this software
• Outstanding problems detected and known limitations
• Procedures for installing and upgrading the software
• Activities conducted to verify that the product is ready for release
NOTE: Read this entire document before attempting to install or use the Foxboro
RTU Station. Also, read the Release Notes for the intermediate releases before
you upgrade from an earlier release.
This document lists the changes made in the Foxboro RTU Station software since the
previous release, SY-1101211, Revision G. You can create a desktop shortcut to
these release notes by installing them on your system.
There are known problems and limitations that remain at the time of product release.
For more information, see Chapter 3: Known Problems and Limitations, page 14. In
this revision, we corrected incidents that would reduce risks to projects worldwide. For
a more detailed assessment of the advantages and disadvantages of adopting SY-
1101211_K for specific projects, visit Global Customer Support at https://pasupport.
schneider-electric.com (registration required).
Revision Information
This revision of the document includes these changes:
Related Documents
For further information on installing, configuring, programming, and diagnosing
Foxboro remote devices and the RTU50, see the documents available on the Foxboro
RTU Product Documentation CD (Part Number: SY-2005654, Revision AA). You can
also see EcoStruxure™ Foxboro SCADA SCD6000 User Documentation CD Release
Notes (B0780SA) for a list of reference documents and their latest versions.
B0780SB, Rev N 5
RTU Station Release Notes Preface
The following list of documents have been updated for the current release:
• EcoStruxure™ Foxboro SCADA SCD6000 Hardware Programming Guide.
(B0780FB)
• EcoStruxure™ Foxboro SCADA RTU Station (SCD6000, SCD5200, RTU50/SVX)
User's Guide (B0780DQ)
• EcoStruxure™ Foxboro SCADA Remote Terminal Viewer (SCD6000, SCD5200,
RTU50/SVX) User's Guide (B0780DY)
• EcoStruxure™ Foxboro SCADA IEC 60870-5-104 Master (SCD6000, SCD5200,
RTU50/SVX) User’s Guide (B0780FC)
• EcoStruxure™ Foxboro SCADA IEC 60870-5-104 Slave (SCD6000, SCD5200,
RTU50/SVX) User’s Guide (B0780DT)
• EcoStruxure™ Foxboro SCADA IEC 60870-5-101 Master (SCD6000, SCD5200,
RTU50/SVX) User’s Guide (B0780EE)
• EcoStruxure™ Foxboro SCADA V.28 Dual Communication Board (SCD6000,
SCD5200, RTU50/SVX) User’s Guide (B0780EN)
• EcoStruxure™ Foxboro SCADA IEC 60870-5-101 Slave (SCD6000, SCD5200,
RTU50/SVX) User’s Guide (B0780EH)
• EcoStruxure™ Foxboro SCADA Intrinsic Database Functions (SCD6000,
SCD5200, RTU50/SVX) User’s Guide (B0780DR)
• EcoStruxure™ Foxboro SCADA DNP3 Slave (SCD6000, SCD5200, RTU50/SVX)
User’s Guide (B0780DC)
• EcoStruxure™ Foxboro SCADA Conitel Slave (SCD6000, SCD5200, RTU50/
SVX) User’s Guide (B0780EL)
• EcoStruxure™ Foxboro SCADA Modbus Slave (SCD6000, SCD5200, RTU50/
SVX) User’s Guide (B0780DG)
• EcoStruxure™ Foxboro SCADA RTU50/SCD5200 to SCD6000 Migration Guide
(B0780FA)
• EcoStruxure™ Foxboro SCADA SCD6000 Installation Guide (B0780EV)
• EcoStruxure™ Foxboro SCADA SCD6000 User Documentation CD Release
Notes (B0780SA)
• EcoStruxure™ Foxboro SCADA Connect Secure Release Notes (B0780SC)
• EcoStruxure™ Foxboro SCADA RTV Release Notes (B0780SD)
• EcoStruxure™ Foxboro SCADA SCD6000 Software Release Notes (B0780SF)
• EcoStruxure™ Foxboro SCADA Foxboro RTU Station CD Read Me First Release
Notes (B0799AX)
6 B0780SB, Rev N
Chapter 1: Functionality and Compatibility RTU Station Release Notes
RTU Software
This version of the Foxboro RTU Station supports:
• Foxboro SCD5200 and RTU50 Software versions (includes utilities) (SY-
1101155-K and later)
• Foxboro SCD6000 Software versions (includes utilities) (SY-1101207_A and
later)
• Foxboro RTU50 SVX Software versions (SY-1101207_C1 and earlier)
The table, “Features Supported by the Foxboro RTU Station”, lists the subsystems
supported by the Foxboro RTU Station for the Foxboro remote devices. For
information on the part numbers of these subsystems, refer to Appendix A, Summary
of Part Numbers in EcoStruxure™ Foxboro SCD6000 Hardware User’s Guide
(B0780DW).
Subsystem For SCD6000 For RTU50 SVX For SCD5200 For RTU50
Input/Output
AC Transducer Card Yes Yes Yes Yes
Type 2
Analog Output Card Yes Yes Yes Yes
32DI/4AI Card (ADI) Yes Yes Yes Yes
- Non-Isolated
32DI/4AI Card (ADI) Yes Yes Yes Yes
- Isolated
12 Digital Output Yes Yes Yes Yes
Card (12DO) (a)
20 Analog Input Yes Yes Yes Yes
Card (20AI) - Non-
Isolated
20 Analog Input Yes Yes Yes Yes
Card (20AI) -
Isolated
Multi I/O Card Yes Yes Yes Yes
Communications
8 Channel Serial Yes Yes Yes Yes
Card
12 Channel Serial Yes Yes Yes Yes
Card (b)
Conitel Master/Slave Yes Yes Yes Yes
B0780SB, Rev N 7
RTU Station Release Notes Chapter 1: Functionality and Compatibility
Subsystem For SCD6000 For RTU50 SVX For SCD5200 For RTU50
Input/Output
C300/C3000 Conitel No No Yes Yes
Slave
DNP3 Master Yes Yes Yes Yes (c)
DNP3 Slave Yes Yes Yes Yes (c)
IEC 60870-5-101 Yes Yes Yes Yes
Master
IEC 60870-5-101 Yes Yes Yes Yes
Slave
IEC 60870-5-103 Yes Yes Yes Yes
Master
IEC 60870-5-104 Yes No No No
Master
IEC 60870-5-104 Yes Yes Yes Yes
Slave
IEC 61850 Client/ Yes Yes Yes Yes
GOOSE Subscriber
IEC 61850 Server/ Yes Yes Yes Yes
GOOSE Publisher
Modbus Master Yes Yes Yes Yes
Modbus Slave (d) Yes Yes Yes Yes
OptoNet Yes Yes Yes Yes
TCP/IP Yes Yes Yes Yes
WISP+ Master No No Yes Yes
WISP+ Slave No No Yes Yes
Calculations
Intrinsic Database Yes Yes Yes Yes
Functions
SALL calculations Yes Yes Yes Yes
(including floating
point and gas
calculations)
IEC 61131-3 No No Yes Yes
(ISaGRAF) (e)
Expansion Bus Yes Yes No Yes
Miscellaneous
Control Interlock Yes Yes Yes Yes
Serial Event Logger Yes Yes Yes Yes
(type 2)
Terminal Server Yes Yes Yes Yes
Diagnostic Router Yes Yes Yes Yes
Diagnostic Server Yes Yes Yes Yes
8 B0780SB, Rev N
Chapter 1: Functionality and Compatibility RTU Station Release Notes
Subsystem For SCD6000 For RTU50 SVX For SCD5200 For RTU50
Input/Output
Analog Logger and Yes Yes Yes Yes
Event logger
SALL HLSI Yes Yes Yes Yes
SNTP Protocol Yes Yes Yes Yes
Zone SEL Yes No No No
Protocol List Yes No No No
Mapping
(a) The 8 Digital Output Card is configured as 12 DO card with relays 9-12 left unconfigured.
(b)
The 12 Channel Serial card is supported only in RTU50. However, the 12 Channel Serial card can be configured
and used in SCD5200, SCD6000, and RTU50 SVX as an 8 Channel Serial card. Channels 9 to 12 cannot be
configured.
(c) Only the SCD6000 supports the DNP3 SAv2 and SAv5 Secure Authentication feature.
(d)
Modbus Slave is only supported on serial communication for all RTU models listed in the table. However,
Modbus TCP Slave is supported for SCD6000 only.
(e)
ISaGRAF is not supported on Windows 7 (64-bit) or later versions of operating system. ISaGRAF Workbench
V3.xx (3.32 or higher, but lower than 4.00) supports RTU50 and SCD5200 running on Windows XP machine.
SCD6000 and RTU50 SVX do not support ISaGRAF.
NOTE: The new modules (Expansion Bus, Zone SEL, and Protocol List Mapping)
will be supported from RTU station version _E or later for SCD6000 with the
firmware version_F or later.
B0780SB, Rev N 9
RTU Station Release Notes Chapter 1: Functionality and Compatibility
You can also buy support for the SALL Compiler using the part numbers in this table.
Superseded Versions
The SY-1101211_K release supersedes these versions of the Foxboro RTU Station
software:
• SY-1101191 (all versions up to revision M, including maintenance releases)
• SY-1101211 (all versions up to revision G, including maintenance releases G13)
10 B0780SB, Rev N
Chapter 2: Changes Since Previous Release RTU Station Release Notes
B0780SB, Rev N 11
RTU Station Release Notes Chapter 2: Changes Since Previous Release
12 B0780SB, Rev N
Chapter 2: Changes Since Previous Release RTU Station Release Notes
B0780SB, Rev N 13
RTU Station Release Notes Chapter 3: Known Problems and Limitations
14 B0780SB, Rev N
Chapter 3: Known Problems and Limitations RTU Station Release Notes
• RTU Station does not launch and it cannot access the postgresql database if
there are any User permission issues.
• RTU Station sometimes is non-responsive when user tries to generate multiple
PLM file in parallel.
• When User account control settings are set to low for non admin users, below
issues will be observed on RTUstation:
◦ RTU station does not launch.
◦ Backup/Restore functionality may not work.
◦ IEC61850 configuration does not import.
• You must first install RTV/RTU Connect Secure/SCD6000 software and then
install RTU Station to avoid any read/write permission issues. RTU Station does
not have weak ACL Implementation, installing it in the end provides access
permissions to the Foxboro folder.
• RTU Station displays exception while restoring the backup database created in
SY01101211_D and earlier versions (Defect#413753 and Defect#413595).
• RTU Station truncates the default point names if the derived names exceed 25
characters (CAR#57806091).
• When you export the basic configuration and import it as a 5200, it deletes the
cards and shows the 10 I/O slot file. When you import it as a 6000, the cards are
pushed over to one slot and a new OptoNet card is placed into the slot
(CAR#57845630).
• IEC points are missing during the import (CAR#57714271).
• When you configure protocol points under slot zero serial and ethernet,
duplication of entity numbers are generated resulting in the detected failure of
control operation (CAR#54233504).
• When uninstalling RTU station version SY-1101211_B3, a detected error
message "1628:failed to complete installation" appears (CAR#58095279).
• IEC61850 client points are deleted when IEC61850 client points in one RTU are
mapped to DNP3 Slave in another RTU, and if any configuration changes are
made in any of the RTUs (CAR#58438281).
• The RTU Station does not allow point names configuration starting with a
numeral. (CAR#58619671).
• Foxboro RTU station SY-1101211 does not launch after installation since Cygwin
bash.exe gets blocked by Cylance Protect or an equivalent end point security
software due to additional security control. You should set up a security exception
for bash.exe application (whitelist) on your operating system (Windows®10 (64-
bit) and Windows Server® 2016 (64-bit)) to overcome this.
◦ To perform whitelisting, do the following:
1. Type secpol.msc in Run dialog box, press Enter. The Local Security
Policy Editor window opens.
2. In the security settings window, look for the policy in Software Restrictions
Policies (SRP).
3. If no policies are found, create a new policy.
4. After a new policy is created, double-click on the Enforcement,
Designated File Types & Trusted Publishers object types for whitelisting
the Cygwin bash.exe application.
◦ However, we recommend you contact the Schneider Electric network support
team and get bash.exe whitelisted.
• While downloading RTU CFG files viewing them in RTV, the Optonet signal ID
suddenly changes to 7362 (CAR#53629222).
• The RTU Station software allows privilege escalation (Standard User to System
Administrator) in the operating system. Consequently, vulnerability exists due to
write permissions being provided to a service executable that can be modified by
any standard user. Upon replacing this executable with a different file and
B0780SB, Rev N 15
RTU Station Release Notes Chapter 3: Known Problems and Limitations
rebooting the system, the 'new file' executes with administrator privileges. This
issue has been tested for both supported operating systems, Windows 10 (1803)
and Windows Server 2016 (CAR#64041681).
• Importing files and CSV import does not work for SCD6000 RTU nodes with two
file electrobus expansion files (CAR#67645711).
• Re-importing a .CID file containing an underscore "_" in the IED name, results in
missing IEC61850 configuration in the RTU station (Defect#474612).
• RTU Station displays an detected validation error message in the DNP3 Slave
serial even if the primary phone number is entered (Defect#445677).
• RTU station displays an detected error and does not map the points to packed
single points of IEC-101 Slave from select point window. You can map the points
individually for each point from the drop down (Defect#446092).
• RTU Station displays an unhandled exception due to the heap size issue
(Defect#462852).
• The DNP3 Slave .csv files are not imported into RTU Station configured with
9000 counter points (Defect#464929).
• Unable to map Conitel Master points in the IEC104 Slave command objects and
DNP3 slave objects (Defect#469361).
• RAIF report generation fails for the IEC61850 Server configuration
(Defect#444080/469900).
• The IDF equations do not have input validations (Defect#475972).
• The Integrated totals are not updated in the IEC101 Master for more than 2500
counter points (Defect#464922).
• You cannot import .csv files into files 2 and 3 on an electrobus expansion file
(Defect#465881).
• When you import and regenerate the Optonet configuration files, some points
disappear from the export block of regenerated CFG files. Those points are
related to IEC104 Slave and double command second slave points
(Defect#475985).
• Foxboro RTU Station version SY–1101211_G5 and above does not have
selection for Floating point in “Reg_IP” group of the Modbus IED. It is available for
selection in the older versions of the RTU Station. (Defect#478614).
16 B0780SB, Rev N
Chapter 4: Validation and Verification Statement RTU Station Release Notes
B0780SB, Rev N 17
Schneider Electric Systems USA, Inc.
38 Neponset Avenue
Foxboro, Massachusetts 02035–2037
United States of America