SYLV. Ny
MECHANICAL DATA
Bulb T6%
Base ‘i a 1, Small Burton 9-Pin
Outline ‘ 2 62
Basing . . ae Bo 9A
Cathode Coated Unipotencial
‘Mounting Position ‘Any
ELECTRICAL DATA
HEATER CHARACTERISTICS
6aX7 12AXT
Heater Voltage Series/Parallel 63/315 126/63 Volts
Heater Current Series/Parallel 300/600 150/300 Ma
Heater Warm-up Time! «* : itt Seconds
Heater-Cathode Voltage
(Design Center Values)
Heater Negative with Respect to Cathode
Total DC and Peak 200 200 Volts Max.
Heater Positive with Respect to Cathode
De 100 100 Volts. Max.
Total DC and Peak 200 200 Volts. Max.
DIRECT INTERELECTRODE CAPACITANCES
Section 1? Section 22
Shielded? Unshielded Shielded? Unshielded
Grid co Plate Ww Wy 17 LT mn
Input (gtoh+k) | 18 16 18 16 pat
Output (ptoh+k) 19 046 19 034 ink
RATINGS (Design Center Values) Each Section
Plate Voluge . =. + ss + +300 Volts Max
Pate Dinipation tt Lt D1) 210 Wart Max
Positive DC Grid Voltage L120 Volts Mex.
Negative DC Grid Volage 2D ~50 Volts Max
CHARACTERISTICS AND TYPICAL OPERATION
Class A; Amplifier —~ Each Section
Plate Voleage . - oe 250 Votes
Grid Voleage =2 Volts
Plate Current << 12 Me
Plate Resistance 62,500 Ohms
Transconductance , 1600 mbox
Amplifestion Factor. | | 100
SYLVANIA
engineering data service jax7
GAX7
QUICK REFERENCE DATA
‘The Sylvania Type 12AX7 is a
miniature high-mu twin triode
having separate cathodes. It is
designed for service as an audio
voltage amplifier or phase in-
verter. The center tapped heater
| of the Type 12AX7 permits oper
ation on 12.6 or 6.3 volts, The
12AX7 is identical to the 6AX7
except for heater characteristics.
‘The 6AX7 employs a 600 Ma
heater and controlled heater
warm-up time for use in series
ig television receivers.
SYLVANIA ELECTRIC
PRODUCTS INC.
RADIO TUBE DIVISION
EMPORIUM, PA.
Prepared and Released By The
‘TECHNICAL PUBLICATIONS SECTION
EMPORIUM, PENNSYLVANIA
SEPTEMBER 1955
PAGE 1 OF 4SYLVANIA
12AX7
GAX7
PAGE 2
NOTES:
1. Heater Warm-up Time is defined as the time required in the circuit shown below for the voltage across the heater
terminals 40 increase from zero to the heater teit voltage (V1). The conditions used im conjunction with the test
circuit depend upon the rated heater voltage and current of the tube under se
For this type: E = 12.5 Volts, R — 15.8 Obms, VI — 25 Volts,
E— Applied Voltage, RMS or DC
= R—Total Series Revistonce
— V1—Heater Test Voltage, RMS or DC
. a (80% Rated Heater Voltage)
2. Section No. 1 connects to Pins 6, 7 and 8.
Section No. 2 connects to Pins 1, 2 and 3.
3. External shield No, 315 connected 10 cathode of section under ses.
4. Controlled Heater Warmup Time applies 10 parallel connection only.SYLVANIA
12AX7
GAX7
PAGE 3
AVERAGE PLATE CHARACTERISTICS
EACH SECTION
500
RATED VALUE,
400
or
300
PLATE VOLTAGE
200
100
3 g 2
S3Y3dMVITTIN NI LNSEUND
40SYLVANIA
V2AX7
GAX7
PAGE 4
AVERAGE TRANSFER CHARACTERISTICS
EACH SECTION
3
£
100 8
3
90
5
z
=
0.4 80
0.12
2
3
a
= 0.10 2800 3
a g
= i
y 0.08 2000 :
5 é
a 5
# 0.06 1500
# g
5 -
one 1000 8
0.02 500 =
-4 =3 =2 = °
CONTROL GRID VOLTS