Professional Documents
Culture Documents
Latest News
On-Demand Mobility As 'Important in Thales to supply 70 mm rocket Developers of U
Aviation As the Dawn of the Jet Age' launchers for Indian attack helicopters Management A
2/14/raytheon-
(https://www.rotorandwing.com/2019/02/23/demand-
(https://www.rotorandwing.com/2019/02/23/thales-
Short on Details
Services (/category/services)
Helicopter vibration adversely a ects rotor blade structural integrity, component life, rewalls, instrumentation, structural
members, and operator comfort and control. Despite large reductions in vibration due to improved helicopter design, the current
overall levels (approximately 0.05 to 0.1g) remain signi cantly higher than that of jet-engine aircraft, which are below 0.01g.
Minimizing these vibration levels, while understanding that they can never be fully eliminated, is essential to ensure a helicopter’s
safety and longevity.
Helicopter vibration is so serious that FAA recently announced its plan to have all U.S.-certi ed rotorcraft install or be serviced
using some type of mechanical condition monitoring or HUMS (health and usage monitoring system). FAA prompted this action
due to the number of helicopter crashes caused by mechanical component failures worldwide, including many that have resulted
in fatalities. The European Union and the Intl Helicopter Safety Team (IHST) also are going ahead with this action due to a series of
fatal accidents that could have been prevented using such technologies.
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 1/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
Why It Happens
Vibrations are inherent in all helicopters. Rotating components are the primary source of helicopter vibration. “By far the biggest
vibration amplitude is seen in the main rotor N-per-revolution (RPM x number of blades) which increases with density altitude,
airspeed and weight,” says Jim Fackler, sole proprietor of Jim Fackler Dynamics of Duarte, Calif. “Being an aerodynamic
phenomena, its severity is logarithmic with airspeed. Next are N-per-revolutions from the tail rotor, then driveshafts because they
cover large areas of the airframe and transmit inordinately to the airframe, followed by higher main rotor harmonics.”
“The primary causes of rotating machinery vibration are unbalance, misalignment, looseness and the excitation of structural
resonances by rotating shaft running frequencies and their harmonics,” says Arun Menon, product manager of San Diego, Calif.-
based Data Physics Corp. “Other sources of vibration can be bearing defects, insu cient lubrication and dirt entrapment between
moving/rotating surfaces. Excessive vibration of main and tail rotors can cause the tail section of helicopters to be physically
ripped from the main structural assembly, and result in catastrophe. Severe imbalance in the rotating parts also can lead to
instabilities during ight making control di cult, if not impossible. Severe vibration can also a ect avionics and navigation
equipment onboard the ght deck.”
Unequal distribution of mass between two opposite rotor blades will create a forcing function when a rotor is spun. “A drive shaft
can have irregular wall thickness or the weight of bolts may be slightly di erent, resulting in a 1/rev (1 x the rotating speed)
vibration each time the heavy spot passes a xed point in space,” says Dave Lilly, manager of technical applications at Honeywell
Aerospace, which is working jointly with Diagnostic Solutions Inc. “Misalignments can cause both 1/rev and 2/rev (1 x and 2 x the
rotating speed) vibrations but using modern installation and maintenance practices these are much rarer today.”
Aerodynamic vibration can be recurring, such as a single blade “lifting” or working harder or less harder than the others in the
group. “These di erences can be the result of mismatching the blade time, small di erences in the airfoil, or such things as
cumulative wear of the leading edge or repeated eld repairs,” says Brian Hatcher, owner of Diagnostic Solutions. “Aerodynamic
vibration of a transitional nature are usually attributed to air ow over irregular surfaces, such as wing stores, and can appear and
disappear as the aircraft moves through ‘conditional’ ow patterns.”
Gears are notorious for vibration issues. Gear manufacturing defects, incorrect assembly tolerances and material defects are all
major contributors of problems that can manifest in high vibration levels, Menon says. Gearbox vibration most often requires a
gearbox overhaul or replacement. Gearbox or drive train vibrations can be harmful to a pilot. The most severe being pain,
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 2/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
Rotor track and balance (RT&B) smoothes and reduces vibrations in helicopters caused by the rotor system. RT&B attempts to
bring each rotational component in the assembly with each other. According to Neil Seamon, senior applications engineer at
Diagnostic Solutions, a number of portable and onboard systems help automate some or all of the process:
• Installation of the equipment (processor, vibration sensors at preselected locations for the task),
One adjustment made during RT&B involves mass imbalance, such as one blade ‘weighing’ more or less than its opposite. “This is
generally solved by adding/removing weights to the root or tip in order to bring the group into harmony,” says Seamon.
“Sometimes referred to as balancing, this is generally done to remove vibration in the lateral, or ‘in-plane’ [with respect to the rotor
disk] vibration.”
Additionally, some aerodynamic tuning is possible on most modern rotor blades through small, semi-rigid tabs installed on the
trailing edge of the blades. These are usually bent, using a specialized tool, up or down as needed to make very small
adjustments to the aerodynamics of a speci c blade. This makes it more closely resemble the others in the rotor system. These
most often are adjusted to reduce the vertical vibrations, or the “hop.” Depending upon the aircraft design, there are also
adjustable pitch links or control rods, which a ect the relationship of the individual blade to the rotating swashplate and a ects
both the lateral and vertical vibration axis. There also may be additional weights moved within a blade (forward and aft) for
additional tuning for speci c faults.
Most RT&B focuses on the 1/rev, or the force that is imparted once per revolution of the rotor system or rotating assembly. “An
additional source of vibration is typically referred to as N/rev, where N equals the number of rotor blades,” says Lilly. “These are
caused by a number of factors such as the ‘work’ of each individual blade and the downward force each blade exerts on the
fuselage as it passes over. Several aircraft employ some form of N/rev absorber and a comprehensive RT&B program will
encompass the tuning of, or at least or assessing the health of these devices.”
Manufacturers have become very good at producing matching blades, but some small variations are bound to occur. These
variations can include chord and span balance and torsional ex. Even if the manufacturer produces matched blades, di erences
can occur during normal use and repair. These small di erences can have an aerodynamic e ect on the way the blade ies and
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 3/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
thus on its track and balance. Sometimes a blade that is slightly out of track is creating the same amount of lift as its neighbors
and thus the same balance. “Even with all these factors, the history of blade track and balance has ingrained a sense of comfort in
the pilot and operators when the aircraft is well tracked,” Hatcher says.
“Manufacturers (not operators) typically yellow arc critical operating modes,” says Fackler. “It’s done in ight test before and during
certi cation. No one operates at criticals, or better said, they won’t for long. Some other helicopters have main rotor RPMs to be
avoided.”
Dynamic signal analyzers are instruments that measure the vibration amplitudes and phase as a function of operating speed for
machinery. “They are integral in the analysis of systems like helicopters and other aircraft,” Menon says. “Dynamic signal analyzers
can o er a variety of tools for total diagnostics of helicopter systems and components including acoustic signature analysis,
vibration analysis with both time and frequency domain tools, synchronous averaging, modal and operating de ection shape
analysis, order analysis and demodulation analysis.”
ShipShape
An accelerometer is the most common type of transducer used to measure vibration. A typical accelerometer hooked to a signal
conditioner produces a voltage that is directly proportional to the instantaneous acceleration of the accelerometer transducer.
This variable signal is produced using the piezoelectric e ect. A small mass acts on the piezoelectric crystal creating a charge
proportional to the force applied. Since the mass and crystal experience no rubbing and very little movement, the accelerometer
has the advantage of long life and a high-frequency range.
A velometer is a transducer that measures the instantaneous velocity of vibration. This is accomplished with a velocity output
accelerometer. This is an accelerometer with a built-in circuit that integrates the acceleration signal into a velocity signal, or coil-
based velometer. In the case of the former, a signal conditioner must be used to provide a proportional voltage output although
proportional to velocity in this case, not acceleration, Menon says.
The coil-based velometer uses a metal coil moving through a magnetic eld producing a voltage proportional to the velocity of
the coil. The principal at work is the Hall E ect. This type of sensor can be big enough to not require signal conditioning, and can
have a sensitivity that is accurate down to lower frequencies than a typical accelerometer. The primary disadvantage can be
mechanical wear since there are moving parts involved.
Spectral Analysis
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 4/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
With advances in sensor technologies, spectral analysis of helicopter components is now possible. Similar to ultrasound
monitoring in medicine, these new digital mechanical microsensors convert vibrations across a spectrum of frequencies into a
signal that can be remotely monitored using wireless transmitters.
In a helicopter’s main rotor gearbox, a frequency is generated for each gear and bearing turning. An individual gear set will
generate a speci c vibration pro le (teeth x RPM). “A malfunctioning helicopter gearbox will show an unusual spectral pro le, like
a murmur in your heart,” says Mark Rose, helicopter pilot of 35 years and manager of Alpine Lift Helicopters, Albany, Ore. “A recent
accident involving a multi-million dollar helicopter and loss of life due to not re lling the tail rotor gearbox could have been
prevented. A low-cost, on-board, temperature/vibration reporting system would have warned the crew in time to land.”
Spectral analysis closely monitors helicopter components for any change that may occur in the normal cycle. It may help detect if
a premature failure is about to occur. These failures can include cracks, loose attachments or bearing failures. In actual operation,
spectral analysis can report and detect vibrations and/or temperatures that exceed normal levels so the cockpit crew can
instantly be alerted via the cockpit-mounted computer display. This wireless system assists the crew in making critical decisions
about continuing ight before a catastrophic in- ight failure occurs. “These systems are required to be FAA accepted but the
guidelines are broad to attract wider use, not to deter use or creativity,” Rose says.
“When an absorbing mass-spring system is attached to a main system mass and the resonance of the absorber is tuned to match
the main system, the motion of the main mass may be signi cantly reduced at its resonance frequency,” Menon says. “Thus, the
energy of the main mass is apparently ‘absorbed’ by the tuned dynamic absorber.”
There are both dynamic and active vibration absorbers. “Dynamic absorbers are like shock struts, dampers and elastomeric
bearings,” says Rose. “Active types are electric-based anti-vibration or absorption panels that may be computer controlled.
Eurocopter has experimented with anti-slap trailing edges in rotor blades that are electrically activated to reduce ight noise in
di erent ight con gurations.”
Fackler says there are basically two types of active absorbers. The rst are those that cancel by applying an equal force opposite
the o ending vibration, typically sprung masses that are tuned to the helicopters N-per rev at its operating frequency. The second
are those absorbers that accumulate energy and return it later in the operating cycle: bi lars and lead lag dampers.
Similar to absorption techniques, isolation removes the transmission path for vibration energy, so if the main rotor and
transmission are isolated from the airframe the airframe will not be susceptible to vibration from these components. Isolation
oating or soft mounting allows the “big pieces” to shake a bit without directly transmitting that motion to the cabin. “This is not a
total solution however, as vibration in those components can still lead to local failure resulting in loss of power and/or control,”
cautions Menon.
Hatcher agrees that since this force is now being taken up by the isolation mounts themselves, they must become an item for
periodic inspection and/or replacement. “The role of the isolation mechanism simply becomes the ‘collection point’ for the
vibration, and therefore must be closely monitored for degradation,” he cautions.
Predictive Mx
Vibration analysis is a very important part of a helicopter’s predictive maintenance program. Predictive maintenance can prevent
breakdowns, unscheduled shutdowns, operational instabilities and expensive repairs.
“Predictive maintenance programs monitor vibration and other system parameter levels over time and track their rate and extent
of deviation from acceptable baseline levels,” says Menon. These types of programs are available commercially and have features
that simplify the data comparison e ort. Ultimately, a predictive maintenance program’s main goal is to identify the failure level of
the component and remove it before a preset threshold.
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 5/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
Predictive maintenance can be handled in-house or by external consultants. Menon believes internal analysis teams should
complete these programs because of knowledge of equipment, regular and frequent access to equipment and regular dialog
with equipment operators and pilots.
Fackler believes it takes both. “I’ve found the operators know their machines the best, but often lack the detail skills in vibration
management,” he says. “Outside consultants are for the most part engineers that feel obliged to nd something whether it is there
or not. Both have vested interests. If you are looking for a company or person to administer a vibration program, look for someone
that has a track record in nding the problem before it is torn down and found. Many analysts point to how their systems identi ed
a problem only after nding the problem post mortem then going back through the data to prove the data.”
Once vibration has been analyzed and discovered, it’s time to tighten, balance, align, lubricate, weight, trim, remove, replace,
repair and correct. “There will never be vibration cessation,” says Fackler. “There will be identi cation of vibration outside the norm
which could trigger a maintenance action that might not otherwise be taken. While there are general rules about helicopter
dynamics, each aircraft is unique and it is best to look at the aircraft against itself rst, then against eet averages. Pragmatically
speaking, helicopters are made to earn a living, not test to death. When you reach a return on the testing—if you reach a return on
the testing—you are doing pretty good.”
(/subscribe/?utm_source=EditorialButton&utm_medium=Article&utm_campaign=EditorialSignUp)
Planned Bristow Acquisition of Columbia Nixed Amid Bristow Bell Singapore Receives Certi cation for MRO Work in China
Financial Loss, Decline in Share Price (https://www.rotorandwing.com/2019/01/22/bell-singapore-
(https://www.rotorandwing.com/2019/02/12/planned- receives-certi cation-mro-work-china/)
bristow-acquisition-columbia-nixed-amid-bristow- nancial-
loss-decline-share-price/)
Leonardo Wins Nearly $400 Million Contract To Maintain U.K. Distilled Water System in Use to Prevent Engine Corrosion in
Apaches Army National Guard UH-72A Fleet
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 6/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
(https://www.rotorandwing.com/2019/01/18/leonardo-wins- (https://www.rotorandwing.com/2018/12/27/distilled-water-
nearly-400-million-contract-maintain-u-k-apaches/) system-use-prevent-engine-corrosion-army-national-guard-
uh-72a- eet/)
LOG IN WITH
OR SIGN UP WITH DISQUS ?
Name
✉ Subscribe d Add Disqus to your siteAdd DisqusAdd 🔒 Disqus' Privacy PolicyPrivacy PolicyPrivacy
Also On RWI
Report: Afghan AF Leader Criticizes MD-530Fs Cassidian to Support German Forces in Afghanistan
(https://www.rotorandwing.com/2015/09/28/report-afghan- (https://www.rotorandwing.com/2012/09/21/cassidian-to-
af-leader-criticizes-md-530fs/) support-german-forces-in-afghanistan/)
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 7/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 8/9
2/26/2019 Vibration Identification & Minimization - Rotor & Wing International
(https://www.facebook.com/rotorandwing)
(https://twitter.com/rotorandwing)
(https://www.linkedin.com/c
&-wing-international)
Quick Links
Personal/Corporate (https://www.rotorandwing.com/category/personalcorporate/)
Commercial (https://www.rotorandwing.com/category/commercial/)
Military (https://www.rotorandwing.com/category/military/)
Public Service (https://www.rotorandwing.com/category/public-service/)
Training (https://www.rotorandwing.com/category/training/)
Products (https://www.rotorandwing.com/category/products/)
Services (https://www.rotorandwing.com/category/services/)
Regulatory (https://www.rotorandwing.com/category/regulatory/)
Safety (https://www.rotorandwing.com/category/safety/)
Webinars (https://www.rotorandwing.com/webinars/)
Podcasts (https://www.rotorandwing.com/podcasts/)
Advertise (https://www.rotorandwing.com/advertising/)
Subscribe to R&WI (https://www.rotorandwing.com/subscribe/)
Contact Us (https://www.rotorandwing.com/contact-us/)
© 2019, Access Intelligence, LLC. All rights reserved. Learn more about licensing or reproducing content on this site. | privacy policy (http://www.accessintel.com/privacypolicy)
https://www.rotorandwing.com/2010/11/01/vibration-identification-minimization/ 9/9