Professional Documents
Culture Documents
Norme Des Brides En1092-1 PDF
Norme Des Brides En1092-1 PDF
Flanges PN 6 EN 1092-1
Dimensions of PN 6 Flanges EN 1092-1
NOTE 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 1/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 2/15
FLANGES ACCORDING TO EN1092-1
Flanges PN 10 EN 1092-1
NOTE 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 3/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter,
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 4/15
FLANGES ACCORDING TO EN1092-1
Flanges PN 16 EN 1092-1
NOTE 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 5/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter,
** 8 holes is preferred however 4 holes may be supplied upon special request by the purchaser.
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 6/15
FLANGES ACCORDING TO EN1092-1
Flanges PN 25 EN 1092-1
NOTE 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 7/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 8/15
FLANGES ACCORDING TO EN1092-1
Flanges PN 40 EN 1092-1
NOTE 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 9/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter,
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 10/15
FLANGES ACCORDING TO EN1092-1
Flanges PN 63 EN 1092-1
NOTE: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 11/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 12/15
FLANGES ACCORDING TO EN1092-1
NOTE: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the
flange.
© IET 13/15
FLANGES ACCORDING TO EN1092-1
Dimensions in mm
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter,
NOTE: The p/t ratings from EN 1092-1 apply only for flange types 05, 11, 12, 13 and 21 having nominal sizes up to
and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.
© IET 14/15
FLANGES ACCORDING TO EN1092-1
© IET 15/15