Professional Documents
Culture Documents
PACKER RETRIEVER
NATIONAL OILWELL VARCO
Introduction
Designed for Engagement of Smooth I.D. Bores
National Oilwell Varco’s Bowen® Smooth Bore Packer Retriever is
designed to be directly connected to a packer mill and to engage a Mandrel
packer with a smooth ID. It allows for constant rotation while milling
and remains in the engaged position to prevent the packer from
falling if it breaks loose. It can transfer torque to the packer if
required and can also be engaged and released multiple times if
needed.
Upper Bearing
Technical Specifications
Size inch 3¾" 4¼" Placing the Retriever Engaging the Packer Milling the Packer Retrieving the Packer Releasing the Packer
and Tubing (if required)
Complete Assembly Grapple Carrier
(less Grapple) Part No. 503845 501650 Operation
Mandrel OD inch 3¾ 4¼ The operation of the retriever is simple. The grapple is locked to the grapple Milling the Packer
carrier in a manner that prevents rotation while still allowing up and down The packer may be milled at any speed and weight. The retriever will travel
mm 95.3 107.9
movement between the grapple and grapple carrier. The grapple carrier is free to downward with the mill while staying in the engaged position should the packer break
ID inch s 1 rotate on the mandrel unless the teeth are engaged between the grapple carrier loose and fall.
mm 15.9 25.4 and nut. Only right hand rotation and movement up and down are required for
Packer Size Range inch 4.000 - 6.000 4.500 - 6.000 Splined Ring complete operation of this tool. Retrieving the Packer and Tubing
mm 101.6 - 152.4 114.3 - 152.4 Placing the Retriever Engagement of the grapple may be tested at any time during the milling operation by
Nominal Catch Range inch ±z ±z stopping rotation and lifting the entire assembly. After the packer has broken free, it is
The retriever is placed far enough under the packer mill to locate the grapple
mm ± 1.59 ± 1.59 inside of the bore to be caught before milling begins. The length of the recommended that rotation be ceased. Upward movement will engage the grapple.
Maximum Tensile lbf. 402,000 512,000 stinger/extension between the packer mill and the retriever is varied to adjust the It is best if the entire assembly can be pulled out of the hole without any right hand
Yield Strength kN 1,788 2,277 location of the tool. rotation to prevent the risk of the retriever releasing from the packer.
Maximum Torsional ft. lbs. 9,500 11,000 Nut Engaging the Packer Releasing the Packer
Yield Strength Nm 12,880 14,914 The milling assembly is run into the hole and the top of the packer located. At any point during the milling operation, the grapple may be released by first setting
Free Stroke inch 12 Standard (36 Optional) 12 Rotation should be ceased or slowed to a minimum while entering the packer down load and then lifting upward slightly while rotating to the right. The grapple will
mm 304.8 (914.4) 304.8 bore. As the retriever enters the bore, the grapple and grapple carrier will slide up unscrew by an amount equal to the lead of the wickers for each rotation.
Overall Length inch 47½ 488 to the shoulder on the mandrel. Additional downward force will compress the
mm 1,206.5 1,222.4 grapple to enter the bore. The entire assembly may now be lowered until the mill
contacts the top of the packer. Once the grapple is positioned in the bore to be
Splined Ring Yes Yes
engaged, rotation may be resumed.
w w w . n o v . c o m
dht.customerser vice@nov.com