Professional Documents
Culture Documents
Before operating and using the device, the appropriate safety and
performance tests must be carried out.
If the yellow LED does not light when the cable ends are shorted,
the cable connection is defective and the cable set should be
replaced.
(For replacement of the integrated electrode cable see point 4 of
the service manual.)
Chart 1
If the time for achieving the initial or final value is exceeded or has
fallen below it significantly, the RC is defective and has to be sent
back for repair.
Position the Stimuplex® Dig RC on a soft base and turn the device
with its bottom panel at the top:
– remove rubber stoppers from the botton panel
– unscrew the 4 screws of the bottom panel with a screw-
driver for recessed-head screws
– pull off the bottom panel carefully upwards and position
it side by side to the device (take care of the battery-
connecting cable!)
– disconnect the electrode cable plug from the plate and
take the electrode cable out of the clamping arrange-
ment of the front panel
– press the new electrode cable with its rubber bushing
into the clamping arrangement of the front panel and
adjust the cable position
– take care of the coding, do not use excessive force;
attach the plug of the electrode cable to the counter
plug on the plate
– replace the bottom panel carefully to seal. Take care
that no cables are being squashed (battery cable)
– screw in the four screws of the botton panel
7
Repair addresses:
B. Braun Melsungen AG
LO-WF-DEOB P
D-34209 Melsungen
D-34209 Melsungen
e-mail: nadja.machal@bbraun.com
Phone (0 56 61) 71-47 89
Fax (0 56 61) 75-47 87
Check Protocol Stimuplex® Dig RC 8
Inspections Status
1. Check the external condition of the device:
– housing clean and undamaged
– labels legible
– current regulator and frequency switch functional
2. Functional Checkups: tests
Turn on the device and adjust a current value of 1 mA:
– brief audio signal sounds in synchrony with the selected frequency
– digital display is flashing
Check the frequency switch (toggle switch):
– signal sounds in time of a second (1 Hz) or in time of 0.5 seconds (2 Hz)
Short the electrode cable:
– prolonged audio signal sounds
– yellow LED is flashing
– digital display indicates the present current (no flashing)
3. Check and observe the output signal (pulsed current):
Blank off the electrode cable with a load resistance of 1000 ohms,
connect the oscilloscope in parallel. Set a pulsed current of 5.0 mA.
Check the output signal with the oscilloscope:
– impulse form monophasic rectangular impulse
– impulse width 0.1 msec. 앐 10 %
– impulse amplitude 5.0 volt (Vp) 앐 10 %
– impulse frequency 1 Hz and 2 Hz 앐 10 %
Set further current values to check:
Current mA Voltage Vp Tolerance
5.0 5.0 앐 10 %
1.0 1.0 앐 10 %
0.5 0.5 앐 10 %
4. Check the monitoring functions
Slowly increase the current when the load resistance is switched on
and check the digit repetition of the digital display:
– the display is 3 digits until 4.99 mA, from 5.0 mA onwards it is 2 digits
– the yellow LED is flashing with each current impulse
– the audio signal is proportional to the selected current
Deenergize the load resistance and slowly increase the current again:
– digital display is flashing on the whole area
– abridged audio signal in proportion to the selected current
Red LED "Batt":
– is flashing briefly when the device is turned on
– is flashing when battery voltage drops below 5.6 V (battery empty)
9
Inspections Status
Battery needs to be replaced during Technical Safety Test.
5. Accessory: Remote Control (Option)
Connect the RC and turn on the Stimuplex® Dig RC:
– digital display indicates initial value of 0.2 mA (± 10 %)
Press the "Up" button until the final value of 5.0 mA is reached.
Press the "Down" button until the initial value of 0.2 mA is reached.
– time duration "Up" and "Down" for each is approximately 20 seconds
Repair
Code number :
Detailed description
of the fault :
Contact Person
(Name/Telephone) :
Supply address :
0123
Caution:für Österreich:
Vertrieb Vertrieb für die Schweiz: B. Braun Melsungen AG
B. Braun Medical
Federal (U.S.A.) Vertriebsgesellschaft
law restricts mbH B. Braun Medical AG HOSPITAL CARE P.O. Box 11 20
In dendevice
this Langäckern 3-5by or on the order
to sale Postfach 21 34201 Melsungen
A-2344 Maria Enzersdorf a. Geb. (NÖ) CH-6203 Sempach-Station
of physicians.
Tel (0 22 36) 8 65 41 Telefon 041 4 62 62 44 Tel (0 56 61) 71-0
Fax (0 22 36) 2 5118 www.bbraun.com
W. 03.03.05/6 Nr. 604 3810