Professional Documents
Culture Documents
HTB1viwiFVXXXXXpXXXX PRXFXXXW
HTB1viwiFVXXXXXpXXXX PRXFXXXW
LCM Specification
( )Preliminary Specification
( ) Final Specification
VERSION: V0
GL Customer
INSPECTION
DESIGNED BY
RESULT
CHECKED BY TESTED BY
APPROVED APPROVED
BY BY
Revision History
Reason
Date Rev.
CONTENTS
GENERAL DESCRIPTIONG
GENERAL FEATURES
ELECTRICAL SPECIFICATIONS
OPTICAL SPECIFICATIONS
BLOCK DIAGRAM
PIN DESCRIPTION
OUTLINE DIMENSION
REGISTER VALUE
TIMING CHARACTERISTICS
INSPECTION CRITERION
PACKING DIMENSION
PRECAUTIONS
2. General Features
Item Display Panel Remark
Effective Area -
Drive IC OTA5180A
Note:
*1) Liquid Crystal driving voltage.
Due to the characteristics of LC Material, this voltage vary with environmental
temperature.
*2) Temp.>60℃, Absolute humidity shall be less than 90%RH at 60℃
*3) Temp.≤60℃, 90%RH MAX.
4. Electrical Specification
Main Window Display
(Unless specified, the ambient temperature Ta=25℃)
Properties Sym. Min Typ. Max Unit Note
Power for Circuit Driving VDD 1.65 2.8 3.3 V Note
Power for Circuit Logic VCI 2.7 2.8 3.0 V Note
BLU Driving Logic Vbat - - - V
Logic Input Low Voltage VIL 0 - 0.2VDD V
Voltage High Voltage VIH 0.8VDD - VDD V
Logic Output Low Voltage VOL 0 - 0.1VDD V
Voltage High Voltage VOH 0.9VDD - VDD V
White Pw T.B.D T.B.D T.B.D mW
Power
Black Pb T.B.D T.B.D T.B.D mW
Consumption
Vertical Stripe Pv T.B.D T.B.D T.B.D mW
Note:
The recommended operating conditions refer to a range in which operation of this product is
guaranteed. Should this range is exceeded, the operation cannot be guaranteed even if the
values may be without the absolute maximum ratings.
Accordingly, please make sure that the module is used within this range. And these current
values are measured under the condition that all devices are stopped, each component is
stable and logic signal is input.
5. Optical Specification
6. Block Diagram
SHENZHEN GELIVABLE OPTOELECTRONICS Co.,LTD.
480×(RGB)×272
Display Panel Gate
(TFT LCD signal
Transmissive) (272)
M
P WR, CS, RS, RESET, RD
U
& Data[(RGB)],Power(VDD)
Control Signal( WR, CS, RS, RESET, RD)
P
O
W K
E
R A
I/F
P/N: GL043015C0-40
GND
VCC
R0 105.50 LCM
R1
A R2 98.70 LCM VA 3.35
2.40
4.42
R3 95.04 LCD AA 5.19 2.92±0.1
R4
R5
R6
8. Outline Dimension
R7
TFT 4.3"
G0
B G1 480 X RGB X 272
G2
G3
57.50 LCM VA
53.86 LCD AA
67.20 LCM
G4
G5
G6
VIEW DIRECTION
G7 YD
B0
152 1
C B1
44.32
B6
B7
GND 单层区 单层区
D
VERSION:V0
30 CLK 1 40 40 1
PI补强
31 DISP
32 Hsync
33 Vsync
34 DEN A1 K1
35 NC
36 GND
B/L CIRCUIT DIAGRAM
37 XR(NC)
E 38 YD(NC)
GELIVABLE OPTOELECTRONICS Co.,LTD.
N.T.S
39 XL(NC)
40 YU(NC)
mm 深圳市给力光电有限公司
12.10.09 GL043015C0-40
480(RGB)X272 DOTS
1
01
Page 10
GELIVABLE OPTOELECTRONICS Co.,LTD.
9. Timing Characteristics
9. 3 Reset Operation
(VCC=1.65~3.1 V)
1) Ambient Condition:
a. Temperature: Room temperature 25±5℃
b. Illumination: Single fluorescent lamp non-directive(300 to 700 Lux)
2) Viewing distance
The distance between the LCD and the inspector’s eyes shall be at least 30-50cm.
3) Viewing Angle
Classification
No. Item Inspection Standard
of defects
(spot defect)
Black and Size Ф (mm) Acceptable Quantity
1 Minor
White spot Ф≤0.1 Ignore
pinhole
0.10≤Ф≤0.15 2
0.15≤Ф≤0.2 1
0.2<Ф 0
(line defect)
Black and Width(mm) Length(mm);Acceptable Qty
2 White line Minor
Polarizer Ф≤0.03 Ignore
scratch 0.03<W≤0.05 L≤3.0; N≤2
0.05<W≤0.1 L≤2.0; N≤2
0.1<W Define as spot defect
Minor
X Y Z
≤3.0 ≤S ≤T
Minor
X Y Z
Ignore ≤0.5 ≤T
Minor
Handing Precautions
(1) The display panel is made of glass and polarizer. As glass is fragile, it tends to become or
Storage Precautions
When storing the LCD modules, the following precaution is necessary.
SHENZHEN GELIVABLE OPTOELECTRONICS Co.,LTD.
Others
Liquid crystals solidify under low temperature (below the storage temperature range) leading to
defective orientation or the generation of air bubbles (black or white). Air bubbles may also be
generated if the module is subject to a low temperature.
If the LCD modules have been operating for a long time showing the same display patterns, the
display patterns may remain on the screen as ghost images and a slight contrast irregularity
may also appear. A normal operating status can be regained by suspending use for some time.
It should be noted that this phenomenon does not adversely affect performance reliability.
To minimize the performance degradation of the LCD modules resulting from destruction
caused by static electricity etc., exercise care to avoid holding the following sections when
handling the modules.
- Exposed area of the printed circuit board.
-Terminal electrode sections.