Professional Documents
Culture Documents
INSTRUCTION MANUAL
MULTI POWER TRANSDUCER MODEL LSMT4
n ENVIRONMENT
BEFORE USE .... • Indoor use
• Do not install the unit where it is directly exposed to rain,
Thank you for choosing M-System. Before use, please check
water droplets or sunlight.
contents of the package you received as outlined below.
• When heavy dust or metal particles are present in the
If you have any problems or questions with the product,
air, install the unit inside proper housing and ventilate it.
please contact M-System’s Sales Office or representatives.
• Do not install the unit where it is subjected to continuous
vibration. Do not apply physical impact to the unit.
■ PACKAGE INCLUDES:
• Environmental temperature must be within -10 to +55°C
Multi Power Transducer.............................................. (1)
(14 to 131°F) with relative humidity within 30 to 90% RH
Output label for users ................................................. (2)
in order to ensure adequate life span and operation.
Mounting slider ........................................................... (2)
n WIRING
■ MODEL NO.
• Do not install cables (power supply, input and output)
Confirm that the model number described on the product is
close to noise sources (relay drive cable, high frequency
exactly what you ordered.
line, etc.).
• Do not bind these cables together with those in which
■ INSTRUCTION MANUAL
noises are present. Do not install them in the same duct.
This manual describes necessary points of caution when
you use this product, including installation, connection and
n AND ....
basic maintenance procedures.
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
POINTS OF CAUTION sheet.
■ GENERAL PRECAUTION
• Before you remove or mount the unit, turn off the power
supply and the input signal for safety.
LIGHTNING SURGE PROTECTION
In order to protect the unit from lightning surges entering
n AUXILIARY POWER INPUT RATINGS through signal and power supply cables, use of appropriate
• Power input ratings are specified by the model number lightning surge protectors are recommended. Please con-
suffix code. tact M-System.
100 – 240V AC rating: 85 – 264V AC, 50/60 Hz, <20VA
110 – 240V DC rating: 99 – 264V DC, <9W
24V DC rating: 24V±10%, <9W
48V DC rating: 48V±10%, <9W
COMPONENT IDENTIFICATION
n FRONT PANEL CONFIGURATION
Output Terminals
DATA Display
Configuration Jack
Input Terminals
INSTALLATION
n WALL MOUNTING n DIN RAIL MOUNTING
Insert the provided slider into upper side of the unit, and Set the unit so that its DIN rail adaptor is at the bottom.
pull out the slider on the lower side. Fasten the M4 screw to Position the upper hook at the rear side of the unit on the
the hole (4.5 mm dia.) of the slider. (torque 1.4 Nm) DIN rail and push in the lower. When removing the unit,
To remove the slider, pull it out while pushing the latch to push down the DIN rail adaptor utilizing a minus screw-
inside as shown in the figure below. driver and pull.
DIN Rail
35mm wide
push push
Slider
DIN RAIL
35mm wide
119 (4.69) (DIN rail mounting)
140 (5.52)
126 (4.96)
115 (4.53)
75 (2.95) 4-M4
126 (4.96)
TERMINAL CONNECTIONS
■ TERMINAL ASSIGNMENT ■ ELECTRICAL CONNECTION
CH11+
Power Input Terminals CONTACT OUTPUT 1
CH11–
Input Terminals
CH12+
CONTACT OUTPUT 2
CH12–
U(+)
POWER
V(–)
FE
JACK CONFIGURATOR
System /
Application
Terminal
P1 P2 P3 1S 1L 3S 3L P1 P2 P3 1S 1L 3S 3L
unbalanced load
P1 P2 P3 1S 1L 3S 3L
u v v u
source k l load
U V V U
L1
K L k l
L2
System / L3
Application
Terminal K L
P1 N 1S 1L P1 N 1S 1L P1 N 1S 1L P1 N 1S 1L
P1 N 1S 1L balanced load P1 N 1S 1L
u v u v
source U V k l load k l
source U V load
L1 L1
K L K L
N L2
L3
N
P1 P2 P3 1S 1L P1 P2 P3 1S 1L
P1 P2 P3 N 1S 1L 2S 2L 3S 3L
source load source k l load
L1 L1
K L
L2 L2
Three phase / L3 L3 source load
3-wire, L1
L2
balanced load P1 P2 P3 1S 1L L3
N
u v v u
source k l load
U V V U
L1 P1 P2 P3 N 1S 1L 2S 2L 3S 3L
K L
L2
L3
Three phase /
4-wire, source k l load
k l
P1 N P3 1S 1L 3S 3L P1 N P3 1S 1L 3S 3L unbalanced load L1
K L k l
L2
K L
L3
K L
N
source load source k l load
L1 L1
K L k l
N N
P1 P2 P3 N 1S 1L 2S 2L 3S 3L
Single phase / L2 L2
K L
3-wire u v u v u v
P1 N P3 1S 1L 3S 3L
source k l load
U V U V U V k l
L1
u v v u K L k l
L2
K L
source k l load L3
U V V U K L
L1 N
K L k l
N
L2
K L
OPERATING MODE
The measurement display items
can be chosen with 4 buttons.
Phase to phase, 1 – 2 Active power, Phase 1 Power factor, Phase 2 Phase to phase THD, 1 – 2
Phase to phase, 2 – 3 Active power, Phase 2 Power factor, Phase 3 Phase to phase THD, 2 – 3
CHARACTER SET
0 1 2 3 4 5 6 7 8 9 – A B C D E F G H I J K L MN O P Q R S T U VWX Y Z
SETTING MODE
■ BUTTON OPERATION
Button Menu/Item Numeric Input
Operating Mode
Enter Passcode
Enter the passcode. Passcode range: 0000 to 9999.
When entered passcode is correct, the unit enters to setting menu.
When entered passcode is incorrect, the unit returns to operating mode with error message.
Incorrect Passcode
Setting Menu
Version
DEV.I
Each time is pressed, the firmware version and the
model number are alternately displayed.
Reboot
REBT
Item Operation
NO Return to Setting Menu
YES Reboot the unit
Change passcode
PASS
The passcode can be changed within 0000 to 9999.
Factory default is 0000.
Loop test
LOOP
By selecting output item of loop test; output selection can be changed.
Item Output Loop test operation
AO1 Analog output 1 → Select the digit in the engineering unit value
↑ Increase the value at selected digit
• •
• •
CT rating, primary
CT1
1 to 20 000 A [5A]
CT rating, secondary
CT2
1 to 5 A [5A]
VT rating, primary
VT1
0.05 to 400.00 kV [0.11 kV] *2
VT rating, secondary
VT2
50 to 480 V [110 V] *2
When this setting is changed, voltage range is automatically
set as shown in table below.
Voltage range
VRNG
50 to 480 (V) [150 V]
AC frequency
FREQ
Item Operation
U1N : Voltage 1 (*)
I1 : Current 1
Pulse weight
WEI
ID PARAMETER
0.001(*) p × 0.001 kWh/pulse
0.01 p × 0.01 kWh/pulse
0.1 p × 0.1 kWh/pulse
1.0 p × 1.0 kWh/pulse
Pulse width
DUR
Selectable within 100 to 2000 msec. by 100 msec. steps.
[100 msec.]
Linearization
LINA
Item Description
SCAL (*) Set 0 % and 100 % for input and output to convert
with Proportional output. Refer to the Proportional
output for settings.
TBL Set the linearization table to convert with the
linearization table. Refer to the linearization
table for settings.
Linearization table
TBL Set input/output of 10 points in the linearization table as shown
below.
Item Description Setting range
IN0 Input 1st point Refer to the Analog
: : output range
IN9 Input 10th point
OUT0 Output 1st point Refer to the Analog
: : output range
OUT9 Output 10th point
Adjustment
ADJ
By selecting item in the table below, output adjustment is
performed in the adjustable range.
12
4
Input (var)
1000 0 1000 0 1000
(LEAD) (LAG) (LEAD) (LAG)
Outgoing Incoming
12 12
4 4
input input
0 1 0 1 0 0 0.5 1 0.5 0 0.5 1 0.5 0
(LEAD) (LAG) (LEAD) (LAG) (LEAD) (LAG) (LEAD) (LAG)
Outgoing Incoming Outgoing Incoming
Option Setting
Menu
To Setting Analog limit
Group Menu ALIM
Select ON/OFF of Analog limit.
Item Description
ON Limit at -1 % and +101 %
OFF (*) No limit (output -5 to +105 %)
System a
configuration ON OFF
Single phase/2-wire 1 1
Single phase/3-wire 2 2
3-phase/3-wire 2 √3
3-phase/4-wire 3 3
Maintenance
Menu
To Setting Backup setting
BKUP
Group Menu
Item Description
NO Return to Maintenance Menu.
YES Backup present settings into internal memory.
Restore setting
REST
Item Description
NO Return to Maintenance Menu.
YES Restore settings in the internal memory.
Initialization
CLR.A
Item Description
NO Return to Maintenance Menu.
YES Initialize settings with default.