Professional Documents
Culture Documents
Shutdown SIS
Previous Screen
Welcome: a3yn3412
Product: MAR INE ENGINE
Mode l: C 32 MAR INE ENGINE R NY00807
C onfiguration: C 32 Marine Engine R NY00001-UP
Specifications
C32 Marine and Auxiliary Marine Engines
Media Number -SENR9772-06 Publication Date -01/06/2011 Date Updated -08/06/2011
i04403751
Cylinder Head
SMCS - 1100
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 1/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
Illustration 1 g02592153
Bolt tightening sequence
Illustration 2 g02592118
(3) Oil gallery
(5) Oil holes
Table 1
Specification for 274-5129 Cylinder Head Gp and 298-6405 Cylinder Head Gp
Item Qty
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 2/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
Use
194 mm (7.6 inch) length for the following bolts: bolt 1 through bolt 10, bolt 15,
32 124-1855 Bolt bolt 17, bolt 19, bolt 21, bolt 23, and bolt 25.
Use
216 mm (8.5 inch) length for the following bolts: bolt 11 through bolt 14, bolt
16, bolt 18, bolt 20, bolt 22, bolt 24, and bolt 26.
Use
149.9 mm (5.90 inch) length for the bolt 27 through bolt 39.
Use the following procedure in order to tighten the cylinder head bolts:
124-1854 Bolt
1 20 Before assembly, apply 4C-5592 Anti-Seize Compound to the bolt threads and
to both sides of the washers for bolt 1 through bolt 26.
1. Tighten the bolt 1 through bolt 26 in a numerical sequence to
270 ± 15 N·m (200 ± 11 lb ft) as shown in the Illustration 1.
2. Tighten the bolt 1 through bolt 26 in a numerical sequence to
450 ± 15 N·m (330 ± 11 lb ft) as shown in the Illustration 1.
248-0036 Bolt 3. Again, tighten the bolt 1 through bolt 26 in a numerical sequence to
26
450 ± 15 N·m (330 ± 11 lb ft) as shown in the Illustration 1.
4. Tighten the bolt 27 through bolt 39 in a numerical sequence to
45 ± 7 N·m (33 ± 5 lb ft) as shown in the Illustration 1.
2W-0482 Install the taperlock studs so that the letter "Y" is showing.
24
2 Taperlock Stud Torque to
35 ± 5 N·m (26 ± 4 lb ft).
Installation depth of the bushing for camshaft is important. Install the bushing to
the following depths:
Dimension (B) is
8.0 ± 0.5 mm (0.31 ± 0.02 inch).
Dimension (C) is
227.5 ± 0.5 mm (8.96 ± 0.02 inch).
Dimension (D) is
216-5582 411.7 ± 0.5 mm (16.21 ± 0.02 inch).
4 7
Bushing Dimension (E) is
595.8 ± 0.5 mm (23.46 ± 0.02 inch).
Dimension (F) is
780.0 ± 0.5 mm (30.71 ± 0.02 inch).
Dimension (G) is
964.1 ± 0.5 mm (37.96 ± 0.02 inch).
Dimension (H) is
1140.3 ± 0.5 mm (44.89 ± 0.02 inch).
NOTICE
Camshaft bearings must be installed into their correct position. Failure to
do so will result in engine damage.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 3/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
Illustration 3 g02592138
Top view
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 4/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
Illustration 4 g02594826
Bottom view
Table 2
Specification for 274-5129 Cylinder Head Gp and 298-6405 Cylinder Head Gp
Item Qty
Part Specification Description
Before assembly, apply green Loctite 620 to press fit diameter of the lower
263-4920 Injector
7 6 end of injector sleeves.
Sleeve
Press the injector sleeve to the bottom of the face (8).
C opyright 1993 - 2014 C ate rpillar Inc. Sat May 03 2014 11:38:45 GMT-0300 (Hora oficial do Brasil)
All R ights R e se rve d.
Private Ne twork For SIS Lice nse e s. a3yn3412
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 5/5