Professional Documents
Culture Documents
Multistage pumps
SPX has many years experience in designing,
You can put pressure on them!
manufacturing and maintaining self-priming
Flange dimensions, bolt circle and number of holes are according DIN 2535
ND 40.
The horizontal pumps are driven by a standard IEC foot motor. The vertical
pumps are driven by a standard IEC flange motor, which is connected to
the lantern piece of the pump. A fitting edge ensures that alignment is not
required. For all pumps the power is transmitted through a flexible coupling.
Shaft sealing options available are mechanical seals as well as gland packing.
Te s t b e d S PX F l o w Te ch n o l o g y i n A s s e n , t h e N e t h e r l a n d s
I S S U E D 1 2 / 2 01 2 J P-MCV-MCH-MCHZ-E N
Multi-stage pump types Typical product applications
Utility
Multistage pumps are used for
pressure booster sets for water
MCH
supply in high rise buildings.
They are used for sinking piles
by water injection on building
M CV
projects. Other main duties
comprise fire fighting units.
T Y P I CA L C H A R A CT E R I S T I C S
• Rigid, reliable construction General industry
In general industry typical
• Available in cast iron and bronze
applications are pumping of
• High pump efficiency
condensate and boiler feeding,
• Suitable for a wide range of duties circulation of hot water or cooling
• Low maintenance cost water.
• Including a self-priming version
• Shaft sealing by means of mechanical seal or gland packing Shipbuilding
Multistage pumps can handle
fresh water as well as sea
water, both clean and slightly
contaminated. Their compact,
space saving build makes them
ideal pumps for engine rooms
T E C H N I CA L DATA
and general duties.
M A X . CA PAC I T Y 10 0 M 3 / H
4 0 BA R , M I N U S 3 x I N L E T
M A X . WO R K I N G P R E S S U R E
PR E SSU R E
M A X . T E M P E R AT U R E - 2 0 ° C / + 15 0 ° C
I S S U E D 1 2 / 2 01 2 J P-MCV-MCH-MCHZ-E N 3
Features and benefits B EAR I NG HOUS I NG
• fitted with 2 apertures
• easily accessible gland housing
MCH
WEAR R I NG S
• on all stages casing wearrings
are applied
MCH FE ET
• pump casing support in • increased maintainability
vertical centre line with
flange and piping
• optimal distribution of forces
MCH Z S E LF-PR I M I NG
S E CT I O N
• contains a built-in vacuum pump
• operates according to the liquid ring
principle
• always ready for immediate duty
• good air and gas handling, discharged
immediately via the pressure pipe
MCHZ
4 I S S U E D 1 2 / 2 01 2 J P-MCV-MCH-MCHZ-E N
P U M P CA S I N G S
• cast flanges on suction and pressure casing
• cast foot on MCV suction casing
• fitted with connections for pressure gauge, balance line, possible
barrier liquid and drain
• versatile casing design
• very rigid and durable construction
• exact positioning in pipework
S TAG E CA S I N G S
• fitted with exchangeable wear
S U CT I O N C O V E R rings
• with 2 anti-rotation vanes located in front of • with radial diffusors
the first impeller
• longer pump life
• prevents for turbulence at impeller entry
• minimal radial forces resulting
• better NPSHr values in low vibration
I M PE LLE R S
M CV CON N E CTI ON
• closed impellers
• pressure flange can be
• designed with 2 sealing edges and balance fitted in 4 ways
holes
• versatile connection
• better hydraulic performance possibilities
• axial forces reduced to a minimum
B EAR I NG
• axially mounted
bearing
• absorbing the
remaining axial thrust
M CV S LI D E B EAR I N G
• lubricated by the pumped
liquid
• fitted in the inlet casing
• requires no maintenance
MCV
I S S U E D 1 2 / 2 01 2 J P-MCV-MCH-MCHZ-E N 5
Shaft sealing is available in two variants:
Shaft sealing • Standardized gland packing rings. When the pressure in the gland becomes too
high the pumps are provided with a balance pipe. For the horizontal pump types
a water cooled stuffing box is optional.
• Mechanical seal with bellows. Cooling and lubrification of this seal is achieved
by circulation of the pumped liquid via a balance pipe.
Cooled
Uncooled
Bearing
• The horizontal pumps are designed
with 2 deep-groove ball bearings.
The largest types have a double-row
angular contact bearing on pressure
side. MCH 14 can be supplied with
a reinforced bearing, consisting of 2
singlerow angular contact bearings on
pressure side. The bearing on pres-
sure side is axially fixed.
• The vertical types are fitted with a
double-row angular contact bearing
which is axially fixed in the lantern
piece. MCV 16 has a deep groove ball
bearing.
• All bearings are grease-lubricated.
• In the suction casing the MCV types
have a slide bearing, lubricated by the
pumped liquid.
6 I S S U E D 1 2 / 2 01 2 J P-MCV-MCH-MCHZ-E N
Performance = limits MCV
= limits MCH
= limits MCHZ
15 0 0 r p m 3000 rpm
85 340
80 320
75
300
10
70
12 10 6 6 280
12
65
260
11 11 9 9
60 5
5 240
5
55 10 8
8 5
10 220
12 9
50 12 10 10
11
9 200 9 7
8 7 4 9
45 11 4
8 4 8
H [m]
10 180 4
10 8
40 7 6 H [m] 6
9 7 160 (9) 7
16
3 (8) 9 7
35 8 6 5 3 5 3
6 140 14 6 3
(7) 6
30 7 8
5 5 4 120 12 5 4
(6) 7 5
25 6 4 11
4 2 2 100 4 2
5 3 (5) 6 2
9 4 3
20
4 3 3 80 8 (4) 5
3 3
15 3 2 6 4
2 1 1 60 (3) 2
2 5 1
10 2 3 2 2 1
40 4
1 1 (2)
1 3 2 1
5 1 1
2 (1) 1
20 1
0
1.2 1.8 2.4 3 4.2 6 9 12 18 24 30 48 0
1.2 1.8 2.4 3 4.2 6 9 12 18 24 30 42 60 90
12.5 14a 14b 16 20a 20b 10 12.5 14a 14b 16 20a 20b
12.5(MCHZ)
Q [m3/h]
Q [m3/h]
18 0 0 r p m 3600 rpm
128 400
120 375
112 350
104 325
12 10 7
12 6 6
96 300
9
88 11 11 275 10 8 6
5 8
5
80 8 250
10 10
12 7 5
72 9 225 9 7
9 7 3
4
64 4
H [m] 8 6 3
11 8 8 H [m] 200 (7)
6 6
56 10 7 4
7 7 175 12
9 5 5
3 3 11 (6)
48 6 150 5
8 6 6 2
2
4 (5) 4 3
40 7 5 5
125 9 4
5
6 2 2 8
32 4 4 (4)
5 3 100 4 3 3
6 2
24 3 3 (3)
4 75 5 3
2 2 2 1 1
3 2 1 1 4 (2)
16 2 2
2 50 3 1
1 1
1 1 2 (1) 1
8 1 25
1
0 0
2 3 4 5 6 7 8 10 15 20 30 40 50 60 1 1.5 2 3 4 5 6 7 8 10 15 20 30 40 50 60 70 80 100
12.5 14a 14b 16 20a 20b 10 12.5 14a 14b 16 20a 20b
Q [m /h] 3
12.5(MCHZ)
Q [m3/h]
I S S U E D 1 2 / 2 01 2 J P-MCV-MCH-MCHZ-E N 7
MCV - MCH -
MCHZ
Multistage pumps
http://www.johnson-pump.com/JPIndustry/JohnsonPump_distributors.htm
S PX F LO W T E C H N O L O GY A S S E N B . V.
SPX reserves the right to incorporate our latest design and material changes without notice or obligation.
Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless
confirmed in writing. Please contact your local sales representative for product availability in your region. For more information visit www.spx.com and www.johnson-pump.com.
The green “>” is a trademark of SPX Corporation, Inc..
ISSUED 12/2012 JP-MCV-MCH-MCHZ-EN
COPYRIGHT © 2009, 2012 SPX Corporation