Professional Documents
Culture Documents
Technical Specification Simba 1354 - 9851 2556 01 - tcm833-1533193
Technical Specification Simba 1354 - 9851 2556 01 - tcm833-1533193
Simba 1354
Technical specification
Standard features
»»Rock drill »»Control system
• Atlas Copco COP 1800-series • Electrical Direct System (EDS)
• Dual-damping system for shock wave absorption and • Anti-jamming system
continuous rock contact for high penetration
• Lubricated and pressurized mating surfaces giving long »»Carrier
service intervals
• Shank adapters suitable for the given hole range • Mine-adapted carrier for small- to medium-sized drifts with
articulated steering and four-wheel drive
»»Drilling unit
»»General
• Mechanized rod handling system
• Feed with hydraulic two-stage cylinder • Trolley-mounted operator panel
• Front- and rear-mounted stinger • FOPS-approved protective roof
• Drill steel support for guidance during collaring and • Electrical cable reel
as support during rod handling • Working lights on tripods
»»Positioning unit
• Tilt, rotation, pendulum arm and slide table
• Accurate and smooth movements
• Mine-adapted, sturdy components
Simba 1354
Specifications
ROCK DRILL »»Electrical system
COP 1838ME
• Total installed power......................................................70 kW
• Main motor at 50 Hz......................................................55 kW
Shank adapter R32, T38, T45, (T51) • Voltage..................................................................380–1 000 V
Hole diameter 51–89 mm
• Frequency..................................................................50–60 Hz
• Starting method..........star/delta (380–690 V) direct (1 000 V)
Impact power 18 kW
• Thermal overload protection for electric motors
Impact rate 54 Hz • Percussion hour meters on A-panel
Hydraulic pressure, max. 250 bar • Digital volt/amperage meter in electric cabinet
Rotation motors Separate rotation • Phase sequence indicator
Rotation speed 0–210/0–140 rpm • Earth fault indicator
Lub. air consump. (at 3 bar) 5 l/s • Battery charger
Water consumption 50 l/min • Transformer.....................................................................4 kVA
• Cable reel
Weight 171 kg
• Limit switch for cable reel
• Working lights on tripods................................2 x 200 W, 24 V
FEED
BMH 200 BMH 214 BMH 215 BMH 216
»»Air system
• Lubricated air for the rock drill
Total length 3 160 mm 3 465 mm 3 770 mm
• Compressor...................................................Atlas Copco LE7
Drill rod length 1 220 mm 1 525 mm 1 830 mm • Capacity at 5 400 rpm and 7 bar......................................12 l/s
Total length with extractor 3 365 mm 3 670 mm 3 975 mm • Air pressure gauge
• Adjustable flow/pressure
• Hole blowing kit with external air
»»Drilling unit • Air flow guard
• Lubrication oil consumption
• Rod Handling System, RHS 17................................ 17+1 rods
• Adaptable to 4′, 5′ and 6′ rods
• Adaptable to R32, T38, T45, (T51) Speedrods »»Water system
• Adaptable to TDS 56 and TDS 64 drill tubes
• Mechanized drilling up to 32 m • Electrically driven water booster pump
• Capacity at 10 bar boost.................................... max 100 l/min
• Min water inlet pressure................................................... 2 bar
»»Positioning system • Water pressure gauge
• Feed extension (with 4′ drill steel).............................. 900 mm • Water flow guard
• Feed extension (with 5′ and 6′ drill steel)................ 1 200 mm
• Rotary Acurator BHR 60–2 for 360º ring drilling »»Carrier
• Sliding table BHT 150 gives 1.5 m feed parallel positioning
• Pendulum arm, BHP 150 gives 1.5 m feed parallel positioning • Deutz 4-cylinder D914 L04, EPA III/COM III (Tier 3/Stage
in the side walls. Adds additional 1.5 m feed parallel position- IIIA) approved 4-stroke prechamber diesel engine
ing upwards/downwards. • Power rating at 2 300 rpm................................. 55 kW (75 hp)
• Stinger backward on feed . ......................................BSJ 8-200 • Torque at 1 500 rpm ....................................................270 Nm
• Stinger forward on feed . ......................................... BSJ 8-115 • Fixed seat for tramming, including safety belt
• Feed dump, drilling.............. +20º forward and -65º backward • Articulated steering................................... ±41° steering angle
• Rig Alignement Laser.................................................RAL650 • Four-wheel drive
• FOPS-approved protective roof
• Hydrostatic power steering system
»»Control system • Hydrodynamic transmission................................Dana T12000
• Electrical Direct System, EDS • Front axle ................................................................. Dana 176
• Basic functions such as semi-automatic drilling and • Rear axle........................................... Dana 176, ±8º oscillation
anti-jamming included • Tyres......................................................................12.00 x R20
• Clearence outside axles....................................................... 15º
• Hydraulic jacks, front........................................... 2 extendable
»»Power pack • Hydraulic jacks, rear...............................................................2
• Service brakes .2 separate circuits (hydraulically applied, fully
• Hydraulic pump for percussion, positioning, feed enclosed wet disc brakes)
• Hydraulic pump for rotation • Emergency and parking brakes......................................SAHR
• Pumps unloaded at start • Fuel tank, volume............................................................... 60 l
• System pressure, max................................................... 230 bar • Electric system..................................................................24 V
• Hydraulic oil tank, volume............................................... 160 l • Batteries.....................................................................2 x 70 Ah
• Low oil level indicator and shut-down • Tramming lights......................................................... 8 x 70 W
• Oil temperature gauge on oil tank • Brake lights
• Electric oil filling pump • Illuminated stairs for platform
• Filtration, absolute.......................................................... 16 μm • Central lubrication system
• Oil filter indicator • Catalyser and silencer
• Water cooled oil cooler in stainless steel • Fire extinguisher
• Mineral hydraulic oil • Spirit levels
• Rock drill lubrication warning kit • Gradeability at max load on drive wheels........................... 1:4
• Hydraulic oil thermostat • Tramming speed, flat ground/incline 1:8............>10/>4 km/h
• Horn, beacon and reverse alarm
• 12V Outlet
• Rig Alignment Laser, RAL 650
Simba 1354
Specifications
DRILL STEEL
Rock drill Hole diameter, mm Drill rod Shank adapter Guide tube
Optional equipment
»»Drilling system »»Electrical system
• Water mist flushing, water oil cooler, external air supply • Electrical cable on reel, Buflex
• Water mist flushing, air oil cooler, external air supply • Plug PC4
• COP 1838MUX, COP 1838HE, COP 1838HUX, • Socket PC4
COP 2550UX • Switch gear
• Electrics according to local standards
»»Positioning system • Working lights on tripods, 2x500 W, 230 V
• Angle Reading Instrument, ARI 6C, with/without
hole depth measurement »»Water system
• Thread lubrication kit • Waterhose reel
• Rod handling system RHS 27 (up to 51 m)
• Automatic lubrication for positioning/drilling system »»Miscellaneous
• Central lubrication for positioning/drilling system
• Additional stinger backwards • Manual lubrication kit
• Rig washing kit
• Shelf for drill bits and tools
»»Carrier • Manual spotlight
• Fire suppression system ANSUL (manual, Checkfire
or automatic)
Simba 1354
Measurements
SIDE VIEW 20º
65º
700
© Copyright 2011, Atlas Copco Rock Drills AB, Örebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos
may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information.
3180
2260
1845
2304 1555 1500 2301
8763 with BMH 216 (B)
945
750 1500 750
RD=Ring drilling 3000 (PH)
PH=Parallel holes
1150
R 750 1500 750 45º 45º
29
1500
70
(R
D) 380o
5220
4890
(PH)
R 27
90 (P
H)
255
7440 1950
2380
2000
2430
WEIGHT
gross weight
kg Total 15 000