Professional Documents
Culture Documents
Dr諾 !ng卜 ‐ 80542E: Technical Report (Manual)
Dr諾 !ng卜 ‐ 80542E: Technical Report (Manual)
TMN 09/クタす E
:117124
O Yourinformalon
Sales agency
O End user
3.Notice
ExpOrt Controli
□ Contro‖ed(Related tem No oF Foreign Exchange Order Attachment List of Japani_____)
■ N o n t c o n t er do ‖f o r i t e m N o 2 t o 1 5 o f F o r e i g n E x c h a n g e O r d e ra Ap ta bn c h m e n t L i s t o f 」
│
i
万
孫
司
.L抽
「ホ l
The memory card for 30i series, 16i series, 0i series,
Power Mate i series, 20i series, 15i series and Data Server
This document describes the recommended memory cards and matters that require attention in the
following applied system.
The CF cards described in this document are recommended memory cards for the following applied
systems.
Owing to characteristics of the flash memory installed in CF cards, a quality of data written in a card
deteriorates through repetition of reading data for a long-term use. It is known that such
deterioration occasionally cause data error. In case of most CF cards on the market, such data error
is not taken into consideration sufficiently. Additionally, the written data in CF cards cannot be read
out immediately, depending on the condition of the memory. In case of DNC operation, this read-out
time delays the data transmission for CNC and influences the result of the processed goods.
The CF cards recommended in this document are designed in consideration of such data error.
These cards have much capability of correcting data automatically. Therefore, these cards do not
read out the wrong data even if such situation occurs. When these cards are used in the range of
conditions described in this document, the delay of read-out time does not influence the result of the
processed goods.
Applied system:
• 30i series
FANUC Series 30i/300i/300is/31i/310i/310is/32i/320i/320is-MODEL A
FANUC Series 31i/310i/310is-MODEL A5
• 16i series
FANUC Series 16i/160i/160is/18i/180i/180is/21i/210i/210is-MODEL A *1
FANUC Series 16i/160i/160is/18i/180i/180is/21i/210i/210is-MODEL B
FANUC Series 18i/180i/180is-M MODEL B5
• 0i series
FANUC Series 0i/0i Mate-MODEL B
FANUC Series 0i/0i Mate-MODEL C
7 FANUC Series 0i/0i Mate-MODEL D
• Power Mate i series
Power Mate i-MODEL D
Power Mate i-MODEL H
• 20i series
FANUC Series 20i-MODEL A
FANUC Series 20i-MODEL B
• 15i series
FANUC Series 15i/150i -MODEL A
FANUC Series 15i/150i -MODEL B
*1. For the information of supported hardware versions and software editions of
using ATA card with 16i series MODEL A, please refer to the CONNECTION
MANUAL (HARDWARE) (B-63003).
TITLE
06 07/08/30 Y.Sato Page 2 is error correction Shimura The memory card for 30i series, 16i series, 0i series,
Power Mate i series, 20i series, 15i series, and Data
05 07/08/06 Shimura Page 2 is modified Shimura Server
CUST.
07 09/07/08 Y.Sato ALL Page are modified DRAW. NO. A-80542E
Edit. DATE Design Description SHEET 1/4
1. The recommended memory card
Fanuc recommends the following memory card.
Table 1-1. A list of the recommended memory card
Purpose
Capacit Data Server *3 7
Specification Data DNC operation Remarks
y *10
Input/Output with memory card 100 Base 10 Base*4
*2
For 0i-B/C
A02B-0281-K601 128MB
A02B-0213-K211 256MB
A02B-0213-K212 1GB
3 A02B-0213-K214 4GB × × *9 × ×
5 A02B-0213-K220 128M × × × × ×
A02B-0213-K221 128M × × × × × This CF card cannot be
ordered newly.
6 A02B-0213-K222 1GB × × × × ×
7 A02B-0213-K230 128M × × × × △ This CF card it used only
7 A02B-0213-K231 by maintenance/capacity
256M × × × × △ change usage of the Fast
7 A02B-0213-K232 1GB × × × × △ Dataserver for 0i-B/C.
3 : Confirmed operation
× : Not guaranteed operation
4 *2. Except for 160is/180is/210is-A/B, 0i/0i Mate-B, Stand-alone type 0i-D and Power Mate i series. and 20i
series.
*3. Except for Power Mate i series and 20i series.
2
*4. Following software is required in order to use the CF card.
In case of 16 i series Control software for Ethernet function : 6561 Edition 15 or later
In case of 15 i series Control software for Ethernet function : 6563 Edition 10 or later
3 *9. Only Fast Data Server in 30i series.
7 *10. : Please order it only by the usages maintenance and the capacity change of the one shipped of the Fast
Data Server (order spec. : A02B-0299-J200, A02B-0309-J146, board spec. : A20B-8101-0450) for 0i-B/C
before October, 2007 (Total edition 01A).
Please use the CF card of a round sign of the one shipped by the Fast Data Server after November,
2007(Total edition since 02B).
Please refer to the column of 100 Base about 0i-D/0i Mate-D.
2 Fanuc uses CF card adapter (Fig. 1-1), A02B-0303-K150, made by FANUC, SDCF-31-03 or
SDAD-38-J60, made by SanDisk for confirming the operation.
7 About the following models (except for Data Server), Fanuc uses CF card adapter (Fig. 1-2),
A02B-0303-K150, made by FANUC for confirming the operation.
・30 i Series
・0 i Series(0i/0i Mate-D)
7
Fig. 1-1) CF card adapter Fig. 1-2) CF card adapter for 30i series
TITLE
07 09/07/08 Y.Sato 7 is modified
When operating DNC operation or Memory operation with these CF cards, pay attention to the
following matters.
4 (1) In case of 16i series, 20i series, 15i series and 0i-C/0i Mate-C, it is necessary to use the following
PCMCIA card attachment.
4 • 16i series, 20i series and 15i series (In case of using CF card, it is necessary to use CF card
adapter, too)
A02B-0236-K163 (for 7.2" or 8.4"LCD unit)
A02B-0236-K164 (for 9.5" or 10.4"LCD unit)
Fig. 2-1) PCMCIA card attachment Fig. 2-2) Appearance after connection
for 16i series and 15i series
• 0i-C/0i Mate-C (In case of using CF card, it is necessary to use CF card adapter, too)
A02B-0309-K160 (for all display unit)
Fig. 2-3) PCMCIA card attachment Fig. 2-2) Appearance after connection
for 0i-C/0i Mate-C
7 (2) In case of 30i series and 0 i series(0i/0i Mate-D), it is unnecessary to use PCMCIA card attachment.
You set a CF card in the CF card adaptor, A02B-0303-K150, and then insert the CF card adaptor
into the PCMCIA slot. You must fix it depressing the lock lever of the PCMCIA slot without fail.
Please close the lid in the memory card interface when you use it. (For all display unit)
TITLE
In case that it is necessary to operate the high performance or process the expensive work-piece,
please use DNC operation of Data Server. In DNC operation of Data Server, this delay of
read-out does not influence the result of process goods and so on.
• Series 16i/18i/21i-A/B, Series 0i/0i Mate-C
Please use the processing time of one block over 16ms.
• Series 15i-A/B
Please use the processing time of one block over 8ms.
7 • Series 30i/31i/32i-A,Series 31i-A5, Series 0i/0i Mate-D
In case of DNC operation, please use the processing time of one block over 4ms.
In case of Memory operation with memory card, please use the processing time of one block
over 24ms.
3. Matters to be attended to operate Memory operation with Data Server in 30i series
4. Matters to be attended to back the SRAM data, etc up in 16i/160is/18i/180is/21i/210is/20i-A and Power
Mate i series
In 16i/160i/160is/18i/180i/180is/21i/210i/210is-A *6, 20i-A, and Power Mate i series *7, it takes long time
to back the SRAM data, etc up to these cards. For example, it takes one and a half minutes to write
a 1MB file and it takes about 5 minutes to write the 3MB file.
And, in case that the vacant capacity of the CF card is not enough, it may take more time to write the
data. In this case, please delete the unnecessary files in the CF card or format the CF card.
*6: In case of 160i/160is/180i/180is/210i/210is-A, this matters that require attention is when using
PCMCIA port on a body of a stand-alone type CNC.
*7: It is restricted to use PCMCIA port on a display unit with touch panel in Power Mate i series.
Refer the details to the technical report, TMN00/180.
Concluded.
TITLE