Professional Documents
Culture Documents
With the Pitzl - RIGID, the designer has the possibility to work with joints with a very
high rotational spring stiffness. Due to the assembling of the beam to the column near-
by the totally height of the inner lever can be used. This is one of the great advantages
compared to other systems where the beams are directly supported on the head of the
columns. Since in most of the constructions the height of the beams are greater than
the dimensions of columns, the sideward connection enables a optimized joint method.
By a combination with the HVP connector, which enables to hang in the beam and after-
wards the fixing of the tension plate - the system is very easy to install.
Beam
Column
Functionality 3
Assembly and installation
The HVP connector is mounted to the column and girding beam (milled into the column).
During assembling, the columns are mounted and then the girders are hang in with the HVP-connectors.
Afterwards the the tension plate is screwed in with inclined screws. Also in that case the plate can milled in.
Beam
Column
48
80
34
23
16
15
250
Ø17
120
Ø9
29
31
17
15
325
Tension plate 325 x 120 x 15
31
Ø17
120
Ø9
58
31
48 60 59 45 38 41 34
17
15
4 RIGID
Modelling of the RIGID joint
In the calculation the rotational bending stiffness must be taken into account. At a negatic bending moment in the
frame corner the RIGID system is working. The rotational stiffness Kφ can be taken from the table. For example for the
88318.4000 the characteristic value is 249 kNm/rad. In the other direction the bending stiffness of the HVP-connec-
tor can be calculated according to the ETA-15/0187. So the PITZl RIGID is a joint with a bilinear bending moment-ro-
tation behavior, and can be calculated with the following diagram:
Example carport
Description
The carport is 3.5 m wide, 5.0 m long and 2.7 m high. The long side is braced diagonally.
The narrow side (entrance) is stiffened with the RIGID 88318.4000.
Wind load:
Schneelast: Zone 2,Zone
wind suction
2, Höhe 480 m,and pressure sk = 0,8
Flachdach wk*=(0,5+0,8)*0,65 kN/m² = 0,85 kN/m²
1,53 kN/m² = 1,22 kN/m²
onto the columns: 0,85 kN/m² * 0,14 m = 0,12 kN/m
Windlast: onto the
Zoneroof:
2, Windsog und Winddruck 0,85 kN/m²kN/m²
wk=(0,5+0,8)*0,65 * 0,4= 0,85
m =kN/m²
0,34 kN/m
auf Stützen: 0,85 kN/m² * 0,14 m = 0,12 kN/m
auf Dachseite: 0,85 kN/m² * 0,4 m = 0,34 kN/m
Load case
LF 1: Permanent
Lastfälle
load
Lastfälle LF 2: Snow load LF 3: Wind in x - direction
Lastfälle Lastfälle
LF 4: Wind in y - Richtung
LF 4: Wind in y - Richtung
LF 4: Wind in y - Richtung
Schnittgrößen in der Ergebniskombination im GZT
LF 4: Wind Schnittgrößen in der Ergebniskombination im GZT
in y - Richtung
Schnittgrößen in der Ergebniskombination im GZT
N Vy Vz
N Vy Vz
N Vy Vz
6 RIGID
N Vy Vz
LF 4: Wind in y - Richtung
LFLF4:4:Wind
Windininy4:
LF y- -Richtung
Richtung
Wind in y - Richtung
LF 4: Wind in y - Richtung
Stress resultant for the decisive load combination in the ultimate limit state (ULS)
Schnittgrößen in der Ergebniskombination im GZT
Schnittgrößen
Schnittgrößen ininder Schnittgrößen
derErgebniskombination
Ergebniskombination
Schnittgrößen imin
im der Ergebniskombination
GZT
GZT
in der Ergebniskombination im GZT im GZT
N Vy Vz
N Vy Vz
N NN Vy VVyy Vz Vz Vz
N Vy Vz
My Mz
My Mz
My My Mz Mz
My My Mz Mz
in x
Verformung inVerformung
der maßgebenden Verformung inErgebniskombination
maßgebenden der maßgebenden
in der Ergebniskombination Ergebniskombination
char. /quasi ständigchar. /quasi ständig in z
in y /quasi ständig
char.
in x in y
in x in x in x in y in y in yin z in z in z
Nachweis Rigid 88318.4000
Nachweis Rigid 88318.4000 Nachweis Rigid 88318.4000
Die maßgebende Beanspruchung resultiert aus der Einwirkung Wind
Nachweis Rigid 88318.4000
Die maßgebende Beanspruchung resultiert
Die aus der Einwirkung
maßgebende KLEDWind
= k./s.k,
Beanspruchung Nutzungsklasse
resultiert 1 -> kmod
aus der Einwirkung = 1,0
Wind
Proof of the DieRIGID connector
maßgebende Beanspruchung resultiert aus der Einwirkung Wind
KLED = k./s.k, Nutzungsklasse 1 -> KLED
kmod ==1,0
k./s.k, Materialsicherheitsbeiwert:
Nutzungsklasse 1 -> k mod = 1,0 γ = 1,3
Decisive stress situation
KLED = k./s.k, γdue
Materialsicherheitsbeiwert:
to wind forces
Nutzungsklasse 1 -> kmod = 1,0 m
m = 1,3Materialsicherheitsbeiwert: γm = 1,3
LDC=short/instantaneous
Materialsicherheitsbeiwert: γm = 1,3service class 1 -> kmod = 1,0
action,
Beanspruchung:Material partial safety-factor:
Tragfähigkeit:
Beanspruchung:
γm = 1,3 Nachweis:
Tragfähigkeit: Nachweis:
Beanspruchung:
NEd = 2,87 kNBeanspruchung:NRd =N31,4 kN * Tragfähigkeit:
1,0/1,3 = kN2,87 Tragfähigkeit:
N=Ed24,2 kN2,87/24,2 = 0,12 Nachweis:
<1,0
Nachweis:
NRd = 31,4 kN * 1,0/1,3 = 24,2 kN 2,87/24,2 = 0,12 <1,0
Ed = 2,87 kN N Rd = 31,4 kN * 1,0/1,3 = 24,2 kN 2,87/24,2 = 0,12 <1,0
VStresses: N = 2,87 kN VRd = 72,6 kN * 1,0/1,3
z,Ed = 1,72 kN Ed V=z,Ed
NRd = 31,4 =
kN * 1,72 kN
1,0/1,3 =
Bearing Vcapacity:
55,8 kN 24,2
1,72/55,8kN = 0,03 V =
2,87/24,2
<1,0
Rd 72,6
= kN
0,12* 1,0/1,3
<1,0 = 55,8
Proof: kN 1,72/55,8 = 0,03 <1,0
Vz,Ed = 1,72 kN Rd = 72,6 kN * 1,0/1,3 = 55,8 kN 1,72/55,8 = 0,03 <1,0
M = -2,34
NEd = 2,87 kN V
kNmz,Ed = 1,72 kN My,Rd = 6,5 kN * 1,0/1,3
V Rd = 72,6
M = kN
5,0= *
kN 1,0/1,3
-2,34 =
kNm 55,8
2,34/5,0 kN= 0,47 1,72/55,8
M
<1,0 = =
6,50,03
kN * <1,0
1,0/1,3 = 5,0 kN 2,34/5,0
< 1,0 = 0,47 <1,0
y,Ed My,Ed = -2,34 kNm NRd = 31,4
y,Ed kN= *6,51,0/1,3
My,Rd = 24,2
kN * 1,0/1,3 y,Rd
= 5,0kNkN 2,34/5,02,87/24,2 = 0,12
= 0,47 <1,0
My,Ed = -2,34 kNm My,Rd = 6,5 kN * 1,0/1,3 = 5,0 kN 2,34/5,0 = 0,47 <1,0
Vz,Ed = 1,72 kN VRd = 72,6 kN * 1,0/1,3 = 55,8 kN 1,72/55,8 = 0,03 < 1,0
My,Ed = -2,34 kNm My,Rd = 6,5 kN * 1,0/1,3 = 5,0 kN 2,34/5,0 = 0,47 < 1,0
Pitzl Metallbau GmbH & Co. KG Tel.: +49 (0) 8703 9346-0 Downloads, technical Need help? Contact to our
Siemensstraße 26 Fax: +49 (0) 8703 9346-55 Information, installation videos: competent employees:
DE-84051 Altheim, Germany info@pitzl-connectors.com www.pitzl-connectors.com +49 (0) 8703 9346-0
All rights reserved. Reproduction and publication - even in part - only with the permission of Pitzl Metallbau GmbH & Co. KG. Changes and errors excepted. Similar pictures. Date 05/2019.