Professional Documents
Culture Documents
Sikaflex®-221
1-COMPONENT ADHESIVE SEALANT
PRODUCT DATA SHEET TEMPLATE FOR TRANSLATION. ONLY FOR INTERNAL USE.
Sikaflex®-221
Version 02.01 (01 - 2019), en_AU
012001202210001000
1/2
CURE MECHANISM Sikaflex®-221 can be processed with hand, PACKAGING INFORMATION
Sikaflex®-221 cures by reaction with atmo- pneumatic or electric driven piston guns as
spheric moisture. At low temperatures the well as pump equipment. For advice on se- Cartridge 310 ml
water content of the air is generally lower and lecting and setting up a suitable pump sys- Unipack 600 ml
the curing reaction proceeds somewhat tem, contact the System Engineering Depart-
slower (see diagram 1). ment of Sika Industry.
BASIS OF PRODUCT DATA
Tooling and finishing All technical data stated in this document are
Tooling and finishing must be carried out based on laboratory tests. Actual measured
within the skin time of the sealant. It is re- data may vary due to circumstances beyond
commended using Sika® Tooling Agent N. our control.
Other finishing agents must be tested for suit-
HEALTH AND SAFETY INFORMATION
ability and compatibility prior to use. For information and advice regarding trans-
Removal portation, handling, storage and disposal of
Uncured Sikaflex®-221 can be removed from chemical products, users shall refer to the ac-
tools and equipment with Sika® Remover-208 tual Safety Data Sheets containing physical,
or another suitable solvent. Once cured, the ecological, toxicological and other safety-re-
material can only be removed mechanically. lated data.
Hands and exposed skin have to be washed DISCLAIMER
Diagram 1: Curing speed for Sikaflex®-221 immediately using hand wipes such as Sika® The information, and, in particular, the re-
Cleaner-350H or a suitable industrial hand commendations relating to the application
CHEMICAL RESISTANCE cleaner and water. Do not use solvents on
Sikaflex®-221 is generally resistant to fresh and enduse of Sika products, are given in
skin! good faith based on Sika's current knowledge
water, seawater, diluted acids and diluted
caustic solutions; temporarily resistant to and experience of the products when prop-
Overpainting
fuels, mineral oils, vegetable and animal fats erly stored, handled and applied under nor-
Sikaflex®-221 can be best painted after form-
and oils; not resistant to organic acids, glycol- mal conditions in accordance with Sika's re-
ation of a skin. Painting could be improved by
ic alcohol, concentrated mineral acids and commendations. In practice, the differences
treating the joint surface with Sika® Aktivator-
caustic solutions or solvents. in materials, substrates and actual site condi-
100 or Sika® Aktivator-205 prior to paint pro-
tions are such that no warranty in respect of
cess. If the paint requires a baking process (>
METHOD OF APPLICATION merchantability or of fitness for a particular
80 °C), best performance is achieved by allow-
Surface preparation purpose, nor any liability arising out of any
ing the sealant to fully cure first. All paints
Surfaces must be clean, dry and free from legal relationship whatsoever, can be inferred
have to be tested by carrying out preliminary
grease, oil and dust. either from this information, or from any writ-
trials under manufacturing conditions.
Surface treatment depends on the specific ten recommendations, or from any other ad-
The elasticity of paints is usually lower than
nature of the substrates and is crucial for a vice offered. The user of the product must
that of sealants. This could lead to cracking of
long lasting bond. Suggestions for surface pre- test the product's suitability for the intended
the paint in the joint area.
paration may be found on the current edition application and purpose. Sika reserves the
of the appropriate Sika® Pre-Treatment Chart. FURTHER INFORMATION right to change the properties of its products.
Consider that these suggestions are based on The information herein is offered for general The proprietary rights of third parties must be
experience and have in any case to be verified guidance only. Advice on specific applications observed. All orders are accepted subject to
by tests on original substrates. is available on request from the Technical De- our current terms of sale and delivery. Users
partment of Sika Industry. must always refer to the most recent issue of
Application Copies of the following publications are avail- the local Product Data Sheet for the product
Sikaflex®-221 can be processed between 5 °C able on request: concerned, copies of which will be supplied
and 40 °C but changes in reactivity and applic- ▪ Safety Data Sheets on request.
ation properties have to be considered. The ▪ Sika Pre-treatment Chart
optimum temperature for substrate and seal- Polyurethane
ant is between 15 °C and 25 °C. ▪ General Guidelines
Bonding and Sealing with Sikaflex® and
SikaTack®
2/2