Professional Documents
Culture Documents
Applications
• Measurement of flow, level or
FMD 230 Flush Mount differential pressure of gases, vapors
and liquids
• Measuring spans from 0.4 inH2O to
580 psi (1 mbar to 40 bar)
• Nominal pressure up to 6000 psi
(420 bar)
• Suitable for use in hazardous areas
ISO 9001
Selection
Differential
Level Flow
Ceramic sensor Silicon sensor pressure
PMD 230 PMD 235 PMD 230, PMD 235 PMD 230, PMD 235 PMD 230, PMD 235
Oval Flange
S
Z
S
10 inH2O to 1200 inH2O 4 inH20 to 580 psi Z
Z
FMD 230 FMD 630 FMD 230, FMD 630
Flange
Z S
metal
flush-mounted ceramic, diaphragm seal as required,
version with metal-free versions with extended
connection diaphragm seal
connections for
sanitary applications
Remote Seal and other diaphragm
seal applications
S
S
Z
Z
2
Mechanical Universal Solution Modular Process Interface
• NEMA 4X housing protected from • The process seals and flanges are
Construction corrosion by a polyester powder easily exchanged
coating – less units need to be stocked
• Separate electronics and connection – allows preventive replacement of
compartments. The display is in the wetted parts operating under
electronics compartment ensuring extremely corrosive conditions
that terminals in the connection • For level, application versions with
compartment are always accesible. flush-mounted ceramic sensors are
available as well as diaphragm seals
or remote seals for practically all
process interfaces.
Oval flange *
Seal *
Ceramic sensor *
Optional display
and cover Optional mounting kit
Test
4...
20
2
mA
3
Connection
1
compartment
0 - 10
BAR
ABS
* Wetted parts
Electronics
compartment
Certificates
The versatiltiy of the Deltabar S is
underlined by world-wide approvals:;
intrinsically safe, explosion proof (FM,
CSA, CENELEC, RIIS), overspill
protection to VbF and WHG (Germany).
3
Operating Principle ➆
aa
➀
➇
Ceramic sensor (left)
➁
➀ ceramic substrate
➁ thick diaphragm for abrasive
and corrosive media ➂ ➈
➂ capacitor electrodes
➃ fritted glass
aa
➄ integrated temperature sensor
for self-monitoring ➃ ➉
➅ fill liquid in a single chamber
Function
A digital communication signal is
superimposed on the 4 to 20 mA signal
line and provides all information
required for remote calibration (SMART).
Other devices connected to the current
output are not affected by this digital
signal.
other
Text
4...20 mA 0000 R instruments
1 2 3
HART® +
4 to 20 mA
protocol
PMD 230:LIC0001
Online PMD 230:LIC0001
1 >Group Select Online
2 PV 8.7 m 1 >Group Select
2 PV 8.7 m
HELP
Commubox
HELP
I
OR FXA 191
O I
O
Personal Computer
with Commuwin II
software
Connecting the handheld terminal
for HART® protocol. EX EX
Commubox FXA 191 is wired
identical to the hand held
terminal.
5
PROFIBUS PA
The PROFIBUS PA is an open fieldbus The number of instruments at one bus
standard for connecting sensors and segment:
actuators, which may also be in hazard- • up to 10 intrinsically safe Deltabar S
ous areas using one bus cable. The two- applications
wire sensors are supplied with power • up to 32 standard Deltabar S
over the PROFIBUS PA line and the applications for non-hazardous areas
process information of the sensor is The above quantities can be operated
digitally transmitted. on a bus segment, the Deltabar S
consumes a maximum of 11 mA per unit.
The Deltabar S with PA electronics is
connected to a segement coupler which PROFIBUS PA is an open bus which
supplies signal to a PLC or personal allows any PROFIBUS PA device to be
computer with Communwin II software. connected to the bus segment; such as
valves, actuators, or other measuring
devices.
PC with PLC
Commuwin II
operating
software
PROFIBUS DP
Deltabar S
p transmitter
Segment
coupler
ENDRESS + HAUSER
Z S
S
S
Z
6
Bus Address
Every device is given a unique bus Power
address. The address can be set using
Display
DIP switches inside the electronic module
housing or through the Communwin II
operating software (ensure DIP switch 8 1 2 3 4 5 6 7 8
Adjustment Range
Calibration Zero and span values are freely adjust-
able within the measuring limits:
lower limit: -100% of rating
upper limit: +100% of rating
• Shifting the zero point leaves the span
unchanged
• Non-linearity better than 0.1%
• Accurate measurement with 20 : 1
turndown
• 4 to 20 mA signal can be inverted
• Adjustable output damping; 0 to 16 s
via switch, 0 to 40 s via handheld
terminal
++
Z
Z
S
S
– –
-5 to 35 inH2O
In calibration mode, pressing a Z key
switches the zero point display
7
Installation Zero Point Correction
2.6"
The Deltabar S is calibrated in the (66.5)
factory according to the zero point
method as per DIN 16 086. There is a
5.63"
difference of 0.8 inH2O (2 mbar) for the (143)
zero point between the vertical and 1.77"
horizontal posititions due to the hydro- (45)
7.7"
static column of the fluid in the sensor. (195) 10.8"
Diaphragm seals thus influence the zero Wall Mount
(274)
secures piping.
_
Maximum
10 ft. glycerine
approximately
156 inH2O
3
= 1.3 sg (1.3 g/cm ) 8 ft H2O
approx. 96 inH2O
3
= 1 sg ( g/cm )
+
p= xgxh
Minimum
8
Planning Hints for Diaphragm Seal Fluid Mounting Instructions for Capillaries
To ensure reliable measurement, the If the transmitter is to be mounted above
FMD 630, PMD 235 process temperature and pressure must or below the measuring pressure point,
with Seals be taken into consideration when the then the maximum height difference
fluid for the diaphragm seal filling is should be 23 feet (7 m). With glycerine,
selected. The compatibility of the fluid the maximum height difference is 13 feet
with the process medium must also be (4 m). Faliure to observe this maximum
considered. will cause the liquid column in the
capillary to outgas and result in damage
• For food processing, only non-toxic to the remote seal. The minimum
liquids such as NEOBEE M-20 may bending radius of the capillary is 4
be used inches (100 mm).
• Special diaphragm seal fluids are to
be used with very low or high process When measuring in a vacuum (negative
temperatures pressure) in a tank, the transmitter
should always be mounted below the
Refer to the chart below for seal fluids position of the lower pressure tapping
currently available. point.
NOTE
To protect the transmitter or diaphragm seals, the
protective caps should be removed just before
installation. The isolating diaphragms or diaphragm
seals must not be depressed or cleaned with
pointed or hard objects. A diaphragm seal and the Recommended Spans and Temperature Effects
transmitter form a closed and calibrated system. It
is filled with diaphragm seal fluid through an Diaphragm Sizes Changes in temperature may have a
opening in the diaphragm seal and body of the The expansion of the diaphragm seal negative effect on the performance and
sensor. This opening is sealed shut and may not fluid with temperature introduces an or accuracy of a transmitter with seals.
be opened.
additional influence on the pressure The fill fluid expansion / contraction at
measurement. The following points varying temperatures will cause
should be noted when selecting the changes in pressure at the measuring
diaphragm seal: cell. By selecting the correct type of seal,
• The nominal width of the diaphragm fill fluid and length of capillaries, the
seal is determined by the diameter of effects may be reduced. Please contact
the diaphragm Endress+Hauser for selection of the best
• The larger the diameter of the solution for your application.
diaphragm, the smaller the
temperature effect.
• For small measuring spans, the
largest possible diaphragm diameter
should be used to limit the effects of
temperature and increase sensitivity.
9
Dimensions 4.1" X
Optional
Display 4.1" View X
(104) (104) 1.54"
(39)
3.15"
(80)
5.9"
(150)
5.35" Y
(without 0 - 40 inH2O
display)
(136)
10"
(255) 7/16-20 UNF
M 10
1-5/8"
(41.3) View Y
1/4-18 NPT
2-1/8"
3.78"
(54)
PMD 230 Deltabar S (96) Optional
with ceramic sensor 3.23" Mounting
(82) Bracket
10"
(255)
1-5/8"
(41.3)
1/4-18 NPT
PMD 230 Deltabar S
with PVDF flange for 2-1/8" 3.78"
metal-free applications (54) (96)
3.23"
(82)
7/16-20 UNF
9.25"
M 10 (M 12)
(235)
3.15" *
(85) 1-5/8"
(41.3) 1/4-18 NPT
2-1/8" 4.17" *
* 3.66" (93) for (54) (106)
6000 psig 3.35" * 4.33"" (110) for
version (85) 6000 psig version
PMD 235 Deltabar S
3.94" **
with silicon sensor (100)
** 5.31" (135) for
6000 psig version
3.15"
(85) 1-5/8"
(41.3)
2-1/8" 4.17"
(54) (106)
3.35"
(85)
3.94"
(100)
10
Dimensions
1.61"
7/16-20 UNF
(41)
M 10
1-5/8"
(41.3)
1-5/8"
7/16-20 UNF
(41.3)
M 10
5.90"
(150)
Vent
valve
1/4-18 NPT
6.94"
(176.3)
316 SS
1.93" Ceramic
(48.9) sensor
5.72"
(145.2) 5.22"
6.25" (133)
(158.8)
Weldspud
Part No.
61001673 2.11"
(54)
3.69"
(94)
0.50"
FMD 230 Deltabar S 5.98" (13)
with tank spud (152)
1.61"
(41)
1-5/8" 41
(41.3)
7/16-20 UNF M 10
M 10 8.27" 7/16-20 UNF 41.3
(210)
210
1/4-18 NPT 1/4-18 NPT
ø1.81" ø 46
(ø46) 0.94" 24
ø6 / 4 x ø0.75" (24) ø160 / 8 x ø22 (26)
(ø152.4 / 4 x ø20) (ø190 / 8 x ø26)
FMD 230 Deltabar S ø7.52" ø200
Flush mounted ceramic (ø191) (ø235)
11
Dimensions
FMD 630
Diaphragm seal - mounting dimensions per ANSI B 16.5
Pipe
Order Nominal Mounting Diaphragm
Code Diameter Flange Holes Seal
Temperature
14.2"
Diaphragm
Diaphragm
Diaphragm
Coefficient
Thickness
Weight of
Extended
Extended
Bolt Hole
Bolt Hole
Pressure
Diameter
Diameter
Diameter
(360)
FMD 630
Nominal
Number
Length
to top of
Width
Circle
Outer
transmitter
g2
in. psi D (in.) b (in.) L (in.) d3 (in.) g2 (in.) k (in.) dW (in) Tk (psi/10°F) lbs
b P 2 150 6 0.75 NA NA 4 0.75 4.75 1.75 0.040 19.8
FMD 630 R 3 150 8.25 0.937 NA NA 4 0.75 6 2.75 0.024 24.3
diaphragm S 3 150 8.25 0.937 2 3 4 0.75 6 2.75 0.024 28.7
dM
T 3 150 8.25 0.937 4 3 4 0.75 6 2.75 0.032 33.1
seal, k U 3 150 8.25 0.937 8 3 4 0.75 6 2.75 0.032 39.7
flush mount
W 4 300 10 1.5 NA NA 8 0.937 6 2.75 0.016 28.7
D
FMD 630 Diaphragm seal - mounting dimensions per DIN 2501
Pipe
Order Nominal Mounting Diaphragm
Code Diameter Flange Holes Seal
Temperature
Diaphragm
Diaphragm
Diaphragm
Coefficient
Thickness
Weight of
Extended
Extended
Bolt Hole
Bolt Hole
Pressure
Diameter
Diameter
Diameter
FMD 630
Nominal
Number
Length
Width
Circle
Outer
FMD 630 L
diaphragm mm bar D (mm) b (mm) L (mm) d3 (mm) g2 (mm) k (mm) dW (mm) Tk (mbar/10K) kg
seal, A 50 40 165 20 NA NA 4 18 125 46 +5 9
extended d3 C 80 40 200 24 NA NA 8 22 160 70 +3 11
D 80 40 200 24 50 76.5 8 22 160 70 +3 13
E 80 40 200 24 100 76.5 8 22 160 70 +4 15
F 80 40 200 24 200 76.5 8 22 160 70 +4 18
G 100 40 235 26 NA NA 8 26 190 70 +2 13
Three-valve Manifold
12
Technical Data Manufacturer Endress+Hauser
General Information
Product Name Deltabar S; PMD 230, PMD 235, FMD 230, FMD 630
Instrument Function Transmitter for differential pressure, flow, or level
Type of Pressure Differential, postive and negative overpressure
Measuring Principle PMD 230, FMD 230: capacitive single-chamber ceramic sensor
PMD 235, FMD 630: piezoresistive silicon sensor
Reference Conditions DIN IEC 770, Tamb = 77°F (25°C) or as stated
Interface 4 to 20 mA, can be superimposed with communications signal
as required (HART®). PROFIBUS PA digital communication is
also available
CE Approval By attaching the CE mark, Endress+Hauser confirms that the
Deltabar S fulfils all legal requirements of the relevant EC
directives.
Mechanical Construction Pressure Connection Common threaded connections and flanges as specified in the
Ordering Information section.
Electrical Connection Selectable entries, 1/2-14 NPT, PG 13.5, M 20 x 1.5, G 1/2 or
PG 13 cable gland. Wiring terminals are for AWG 20 to AWG 13,
interlock diode integrated. 2-wire connection using commercial
instrument cable (with shield for PROFIBUS connection).
Weight PMD 230, approximately 11 lbs (5 kg)
PMD 235, 8.8 to 13 lbs (4 to 6 kg) depending on version
FMD 230, with 3” flange, 17.6 lbs (8 kg)
Silicon Sensor:
Nominal Limits Span System Pressure Pressure
Value transmission
sensor fluid
PMD 235 lower-range upper-range minimum maximum overload overload
FMD 630 value value one side both sides
4 inH2O * -4 inH2O 4 inH2O 0.4 inH2O 4 inH2O 2000 psi 2000 psi silicon oil **
10 mbar * -10 mbar 10 mbar 1 mbar 10 mbar 140 bar 140 bar
16 inH2O * -16 inH2O 16 inH2O 2 inH2O 16 inH2O 2000 psi 2000 psi silicon oil **
40 mbar * -40 mbar 40 mbar 5 mbar 40 mbar 140 bar 140 bar
64 inH2O -64 inH2O 64 inH2O 4 inH2O 64 inH2O 2000 psi 2000 psi silicon oil **
160 mbar -160 bar 160 mbar 10 mbar 160 mbar 140 bar 140 bar
400 inH2O -400 inH2O 400 inH2O 20 inH2O 400 inH2O 6000 psi *** 6000 psi *** silicon oil **
1 bar -1 bar 1 bar 50 mbar 1 bar 420 bar *** 420 bar ***
87 psi -87 psi 87 psi 4.35 psi 87 psi 6000 psi *** 6000 psi *** silicon oil **
6 bar -6 bar 6 bar 300 mbar 6 bar 420 bar *** 420 bar ***
580 psi * -580 psi 580 psi 29 psi 580 psi 1450 psi 6000 psi *** silicon oil **
40 bar* -40 bar 40 bar 2000 mbar 40 bar 100 bar 420 bar ***
* PMD 235 only
** Voltalef 1A for oxygen service, grease free
*** Check nominal pressure rating of flange
13
Minimum Static Pressure PMD 230, PMD 235, FMD 230: pabs greater than 0.0145 psia
(1 mbar) for all sensors and measuring ranges
FMD 630: pabs greater than 0.145 psia (10 mbar) for all sensors
and measuring ranges
Wetted Parts Materials PMD 230, FMD 230: ceramic diaphragm, process connection
and seal as required
PMD 235, FMD 630: 316 SST for the sensor metallic separating
diaphragm, process connection and seal as required
PMD 235 with seals: metallic separating diaphragm of the
diaphragm seal and process connection as required.
Pressure Transmission PMD 230, FMD 230: silicon oil for sensors 10 inH2O (25 mbar)
Fluid and 40 inH2O (100 mbar), mineral oil for sensors 200 inH2O
(500 mbar), and 1200 inH2O (3000 mbar).
Voltalef 1A for oxygen service, grease free.
PMD 235, FMD 630: for sensor, silicon oil. Voltalef 1A for
applications in purified gas, e.g. oxygen. For diaphragm seal,
fluid as required.
14
Output, PROFIBUS PROFIBUS PA Function Slave
Transmission Rate 31.25 kByte/s
Response Time Slave; approximately 20 ms. PLC; approximately 600 ms for
approximately 30 devices
Signal on Alarm PROFIBUS PA, signal status bit is set, last valid measured value
held. Display, error code displayed.
Damping 0 to 40 seconds via communication
Communication Resistor None, separate PROFIBUS PA termination
Physical Layer IEC 1158-2
Power Supply Voltage Range Standard 11.5 to 45 VDC (refer to charts below). Refer to
PROFIBUS voltage below for power requirements.
Field of operation for Deltabar S Field of operation for Deltabar S
PMD 230 / FMD 230 PMD 235 / FMD 630
R/ for max 21.5 mA R/ for max 21.5 mA
1560 1560
1000 1000
860 860
500 500
0 0
11.5 20 30 45 U/V 11.5 20 30 45 U/V
Standard Intrinsically safe Standard Intrinsically safe
Explosion proof
16
PMD 235 Differential pressure PMD 235 - 1 2 3 4 5 6 7
transmitter with silicon sensor
1 Certificate / Cable Entry
C EEx ia IIC T4/T6, PG 13.5 cable entry
T EEx d IIC T5/T6, PG 13.5 cable entry
W FM approved intrinsically safe, CL I, II, III; Div. 1; Grps A-G
Non-incendive, CL I; Div. 2; Grps A-D
Dust-Ignition, CL II, III; Div. 1; Grps E-G
1/2” NPT conduit entry
U FM approved explosion proof, CL I, II, III; Div. 1: Grps A-G
1/2” NPT conduit entry
2 CSA IS (non-incendive), CL I, II, III; Div. 1; Grps A-G
1/2” NPT conduit entry
1 CSA explosion proof, CL I, II, III; Div. 1; Groups B-G
1/2” NPT conduit entry
Y Special version
2 Electronics, display, housing
B 4 to 20 mA HART, LCD display, top cover
H 4 to 20 mA HART, without display, top cover
U 4 to 20 mA HART, LCD display, side cover
M 4 to 20 mA HART, without display, side cover
D PROFIBUS PA, LCD display, top cover
I PROFIBUS PA, without display, top cover
P PROFIBUS PA, LCD display, side cover
X PROFIBUS PA, without display, side cover
Y Special version
3 Silicon sensor min/max span, sensor material (maximum static pressure)
4A 0.4 to 4 inH2O, 316 SS (2000 psi) 1 to 10 mbar (140 bar)
4C 2 to 16 inH2O, 316 SS (2000 psi) 5 to 40 mbar (140 bar)
4E 4 to 64 inH2O, 316 SS (2000 psi) 10 to 160 mbar (140 bar)
4G 20 to 400 inH2O, 316 SS (2000 psi) 50 to 1000 mbar (140 bar)
4K 4.35 to 87 psi, 316 SS (2000 psi) 0.3 to 6 bar (140 bar)
4M 29 to 580 psi, 316 SS (2000 psi) 2 to 40 bar (140 bar)
5G 20 to 400 inH2O, 316 SS (6000 psi) 50 to 1000 mbar (420 bar)
5K 4.35 to 87 psi, 316 SS (6000 psi) 0.3 to 6 bar (420 bar)
5M 29 to 580 psi, 316 SS (6000 psi) 2 to 40 bar (420 bar)
BA 0.4 to 4 inH2O,Hastelloy C (2000 psi) 1 to 10 mbar (140 bar)
BC 2 to 16 inH2O, Hastelloy C (2000 psi) 5 to 40 mbar (140 bar)
BE 4 to 64 inH2O, Hastelloy C (2000 psi) 10 to 160 mbar (140 bar)
BG 20 to 400 inH2O, Hastelloy C (2000 psi) 50 to 1000 mbar (140 bar)
BK 4.35 to 87 psi, Hastelloy C (2000 psi) 0.3 to 6 bar (140 bar)
BM 29 to 580 psi, Hastelloy C (2000 psi) 2 to 40 bar (140 bar)
HG 20 to 400 inH2O, Hastelloy C (6000 psi) 50 to 1000 mbar (420 bar)
HK 4.35 to 87 psi, Hastelloy C (6000 psi) 0.3 to 6 bar (420 bar)
HM 29 to 580 psi, Hastelloy C (6000 psi) 2 to 40 bar (420 bar)
4 Calibration / Units
C Nominal calibration 0.05%, psi, platinum version
1 Nominal value / mbar, bar; linear
2 Nominal value / kPa, MPa; linear
3 Nominal value / mmH2O; linear
4 Nominal value / inH2O; linear
5 Nominal value / kgf, cm2 ; linear
6 Nominal value / psi; linear
9 State initial and end value, units in writing; linear or square
5 Accessories (fittings)
EA Without
EB 2 blind taps, SS
ED 2 vent valves, SS
EG 2 blind taps, 1 mounting bracket
EH 2 vent valves, 1 mounting bracket
EM 1 mounting bracket for wall and pipe
EY Special version
6 Process seal (wetted parts)
1 FPM (Viton, fluoroelastomer)
2 NBR (Buna-N)
3 PTFE from 0.0145 psia (1 mBar)
6 FPM Viton, grease free for oxygen use (Tmax = 140°F, Pmax = 1000 psi)
8 Viton o-ring, grease free
9 Special version
7 Process connection (1/4-18 NPT)
A Oval flange, C22.8, DIN 19213, (PN140, M10 mounting, PN420, M12 mounting)
B Oval flange, C22.8, 7/16-20 UNF
C Oval flange, 316L SS, DIN19213, (PN140, M10 mounting, PN420, M12 mounting)
D Oval flange, 316L SS, 7/16-20 UNF
F Oval flange, Hastelloy C, 7/16-20 UNF
Y Special version
17
FMD 230 Differential pressure FMD 230 - 1 2 3 4 5 6 7 8
transmitter, flush mounted ceramic
sensor 1 Certificate / Cable Entry
C EEx ia IIC T4/T6, PG 13.5 cable entry
W FM approved intrinsically safe, CL I, II, III; Div. 1; Grps A-G
Non-incendive, CL I; Div. 2; Grps A-D
Dust-Ignition, CL II, III; Div. 1; Grps E-G
1/2” NPT conduit entry
2 CSA IS (non-incendive), CL I, II, III; Div. 1; Grps A-G
1/2” NPT conduit entry
Y Special version
2 Electronics, display, housing
B 4 to 20 mA HART, LCD display, top cover
H 4 to 20 mA HART, without display, top cover
U 4 to 20 mA HART, LCD display, side cover
M 4 to 20 mA HART, without display, side cover
D PROFIBUS PA, LCD display, top cover
I PROFIBUS PA, without display, top cover
P PROFIBUS PA, LCD display, side cover
X PROFIBUS PA, without display, side cover
Y Special version
3 Ceramic sensor min/max range, (maximum static pressure)
2D 2 to 40 inH2O (230 psi) 5 to 100 mbar (16 bar)
3F 10 to 200 inH2O (1450 psi) 25 to 500 mbar (100 bar)
3H 60 to 1200 inH2O (1450 psi) 150 to 3000 mbar (100 bar)
9Y Special veraion
4 Calibration / Units
1 Nominal value / mbar, bar; linear
2 Nominal value / kPa, MPa; linear
3 Nominal value / mmH2O; linear
4 Nominal value / inH2O; linear
5 Nominal value / kgf, cm2 ; linear
6 Nominal value / psi; linear
9 State initial and end value, units in writing; linear or square
5 Accessories (fittings)
EA Without
EC One vent valve, 316 SS
EY Special version
6 Process seal (wetted parts)
1 FPM (Viton, fluoroelastomer)
3 PTFE faced Hastelloy C-4 for pabs > 13 psia (900 mbar)
4 EPDM
6 FPM Viton for oxygen service, grease free (Tmax 140°F, Pmax 1000 psi)
7 Kalrez
8 Viton o-ring, grease free
9 Special version
7 Low side process connection (1/4-18 NPT)
A Oval flange, C22.8, DIN 19213, M10 threaded
B Oval flange, C22.8, 7/16-20 UNF
C Oval flange, 316L SS, DIN19213, M10 threaded
D Oval flange, 316L SS, 7/16-20 UNF
F Oval flange, Hasteloy C, 7/16-20 UNF
FMD 230 “WH” version Y Special version
8 High side process connection “+”
DK 3” 150 lb ANSI flange; 316L SS
DM 3” 150 lb ANSI flange; ECTFE coated (HALAR)
DN 3” 150 lb ANSI flange, Hastelloy C-276
DR 4” 150 lb ANSI flange; 316L SS
DS 4” 150 lb ANSI flange; ECTFE coated (HALAR)
DT 4” 150 lb ANSI flange, Hastelloy C-276
WH Sanitary tank weld spud, 2” extension, clamp mount
316L SS, low pressure side 1/4-18 FNPT
BK DN 80, PN 40; 316L SS
BM DN 80, PN 40; ECTFE coated flange
BN DN 80, PN 40; Hastelloy C-276 flange
BR DN 100, PN 40; 316L SS
BS DN 100, PN 40; ECTFE coated flange
BT DN 100, PN 40; Hastelloy C-276 flange
4” clamp YY Special version
18
FMD 630 Differential pressure FMD 630 - 1 2 3 4 5 6 7 8 9
transmitter with diaphragm seal
for level measurement 1 Certificate / Cable Entry
C EEx ia IIC T4/T6, PG 13.5 cable entry
T EEx d IIC T5/T6, 1/2” NPT
W FM approved intrinsically safe, CL I, II, III; Div. 1; Grps A-G
Non-incendive, CL I; Div. 2; Grps A-D
1/2” NPT conduit entry
U FM approved explosion proof, CL I; Div. 1; Grps A-D
Dust ignition proof, Class II, III; Div 1; Grps E-G
1/2” NPT conduit entry
2 CSA IS (non-incendive), CL I, II, III; Div. 1; Grps A-G
1/2” NPT conduit entry
1 CSA explosion proof, CL I, II, III; Div. 1; Grps B-G
1/2” NPT conduit entry
Y Special version
2 Electronics, display, housing
B 4 to 20 mA HART, LCD display, top cover
H 4 to 20 mA HART, without display, top cover
U 4 to 20 mA HART, LCD display, side cover
M 4 to 20 mA HART, without display, side cover
D PROFIBUS PA, LCD display, top cover
I PROFIBUS PA, without display, top cover
P PROFIBUS PA, LCD display, side cover
X PROFIBUS PA, without display, side cover
Y Special version
3 Ceramic sensor min/max span, (maximum static pressure)
4E 4 to 64 inH2O (2000 psi) 10 to 160 mbar (140 bar)
4G 20 to 400 inH2O (2000 psi) 50 to 1000 mbar (140 bar)
4K 4.35 to 87 psi (2000 psi) 300 to 6000 mbar (140 bar)
9Y Special veraion
4 Calibration / Units
1 Nominal value / mbar, bar; linear
2 Nominal value / kPa, MPa; linear
3 Nominal value / mmH2O; linear
4 Nominal value / inH2O; linear
5 Nominal value / kgf, cm2 ; linear
6 Nominal value / psi; linear
9 State initial and end value, units in writing; linear or square
5 Accessories (fittings)
EA Without
EC One vent valve, 316 SS
EY Special version
6 Process seal (wetted parts)
1 FPM (Viton, fluoroelastomer)
2 NBR (Buna-N)
3 PTFE
6 FPM Viton for oxygen service, grease free (Tmax 140°F, Pmax 1000 psi)
8 Viton o-ring, grease free
H Copper (for use with Process Connection “H” only)
9 Special version
7 Low side process connection (1/4-18 NPT)
A Oval flange, C22.8, DIN 19213, M10 threaded
B Oval flange, C22.8, 7/16-20 UNF
C Oval flange, 316L SS, DIN19213, M10 threaded
D Oval flange, 316L SS, 7/16-20 UNF
H Oval flange for diaphragm seal mounting
Y Special version
8 High side process connection “+”
P 2” 150 lb ANSI flange; 316L SS
R 3” 150 lb ANSI flange; 316L SS
S 3” 150 lb ANSI flange; 2” extension, 316L SS
T 3” 150 lb ANSI flange; 4” extension, 316L SS
U 3” 150 lb ANSI flange; 8” extension, 316L SS
W 4” 300 lb ANSI flange; 316L SS
A DN 50, PN 40; 316L SS flange
C DN 80, PN 40; 316L SS flange
D DN 80, PN 40; extension, 50 mm, 316L SS
E DN 80, PN 40; extension, 100 mm, 316L SS
F DN 80, PN 40; extension, 200 mm, 316L SS
G DN 100, PN 40; 316L SS flange
9 Special version
9 Diaphragm material and seal liquid
A Hastelloy C, Silicon fill
D Hastelloy C, high-temp oil fill
F Tanatlum, Silicon fill
G Tantalum, high-temp oil fill
1 316L SS, Silicon fill
2 316L SS, Neobee-M20 oil fill
3 316L SS, Glycerin fill
4 316L SS, high-temp oil fill
5 316L SS, oil fill for oxygen application
9 Special diaphragm and fill fluid
19
Deltabar S HART®
Program Matrix
Group Select
1 (H0) 2 (H1) 3 (H2) 4 (H3) 5 (H4) 6 (H5) 7 (H6) 8 (H7) 9 (H8) 10 (H9)
Set bias
Basic Measured Set Set Set 4mA Set 20 mA Set bias Output Pressure
1 (V0) calibration value 4 mA 20 mA automatically automatically pressure
pressure Damping
on alarm unit
automatically
Current Last
Transmitter Minimum Maximum Overload Current Minimum Maximum
2 (V2) information
diagnostic diagnostic Software no.
pressure pressure counter temperature temperature temperature Reset
code code
Lineari- Operating 4 mA after 20 mA after Unit after Density Low flow Level Table Entry Entry
3 (V3) zation mode linearization linearization linearization factor cut-off manual number level volume
Process Process
User Tag no. User text Device Sensor Process
6 (VA) information serial no. serial no.
connection connection Seal
diaphragm
Oil fill
P+ P–
Pressure Unit
Conversion Table
To Pa (N/m )
2
kPA MPa bar mbar mm H2O kg/cm2 atm inch Hg mm Hg inch H2O psi
From
2
Pa (N/m ) 1 10
-3
10
-6
10
-5 -2
0.1020 1.020 x 10
-5
9.869 x 10
-6 -4
10 2.953 x 10 7.501 x 10
-3
4.016 x 10
-3
1.451 x 10
-4
psi 6.895 x 103 6.895 6.895 x 10-3 0.0689 68.948 704.3 0.0704 0.0680 2.036 51.71 27.73 1