Professional Documents
Culture Documents
FLUID MECHANICS
3rd Exam/Civil/0510/Feb'2021
Duration: 1.15Hrs. M.Marks:25
SECTION-A
Q1. Attempt any three questions. 3x5=15
i. What is water hammer?
ii. Explain various types of flows.
iii. What is venturimeter?
iv. Differentiate between notch and weir.
v. Differentiate between steady and unsteady flow
vi. What is total energy line?
vii. What is pascal’s law? What are its applications?
SECTION-B
Attempt any one question. 1x10=10
Q2. If the specific gravity of a liquid is 0.8 find /or make calculation for its mass density, specific volume and
specific weight?
Q3. A channel of rectangular cross section is 4.5m wide and 1.5 m deep .discharge of water through channel is
8.5m3/sec .find the bed slope if chezy ‘constant is 52
Q4. A square plate 3mx3m hangs in water from one of its corners and its centroid lies at a depth of 10m from
the free water surface calculate its.
a. Total pressure on plate
b. Position of centre of pressure w r.t .its centroid
Q5. Find the head lost due to friction in a pipe of diameter200mm and length 60m, through which water is
flowing at a velocity of 2.5 m/s using
a) Darcy formula (assuming f=0.005) b) Chezy’s formula for which C=55.
S.B. Roll No………………………………………….
FLUID MECHANICS
3rd Exam/Civil/7651/Feb'2021
(For 2018 batch onwards)
Duration: 1.15Hrs. M.Marks:25
SECTION-A
Q1. Attempt any three questions. 3x5=15
i. Write a short note on Vapor Pressure.
ii. What is a hydraulic press?
iii. Write a short note on differential manometer.
iv. Write short note on dead weight pressure gauge.
v. State Bernoulli’s theorem. What are its assumptions?
vi. What different types of Notches?
vii. What is Reynold’s Number?
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Explain Different types of Fluid flows in details.
b. Explain Total Energy line and Hydraulic gradient line in details with diagram.
c. A triangular plate of base 3m and height 4m lies immersed vertically in water with the apex
downward. The base of plate is 1m below the free water surface. Determine the total Pressure and
center of pressure.
d. Find the discharge through trapezoidal notch which is 1.5m wide at the top and 0.54m at bottom. The
height of notch is 0.4m and head of water on the notch is 0.3m. Take Cd = 0.60
S.B. Roll No………………………………………….
SECTION-B
Attempt any one question. 1x10=10
Q2. Describe the various varnishes used for electrical purposes as well as give their uses.
Q3. Describe the classification of ceramic materials.
Q4. a) Discuss applications of following insulating materials: i) Glass ii) Porcelain
b) Name at least 5 parts of a DC machine & the material used for construction of those parts.
Q5. Explain the classification of magnetic materials. Also explain some of the properties of magnetic
materials.
S.B. Roll No………………………………………….
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Explain classification of materials into conductor, semiconductor and insulator on the basis of atomic
structure?
b. What are bundle conductors and write its applications?
c. What are the differences between thermosetting materials and thermo-plastic materials?
d. List the materials used for the construction of transformer?
S.B. Roll No………………………………………….
MATERIAL SCIENCE
3rd Exam/Mech./RAC/Prod/0536/Feb'2021
Duration: 1.15Hrs. M.Marks:25
SECTION-A
Q1. Attempt any three questions. 3x5=15
i. Define the term resilience and fatigue.
ii. Explain the plastic deformation by Twining.
iii. Write any six properties of copper.
iv. What is the difference between substitutional solid solution and interstitial solid solution?
v. Explain Induction Hardening Process.
vi. Define various Thermoplastic materials.
vii. Write any six applications of ceramics.
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Calculate the Atomic packing factor (A.P.F.) for BCC and FCC structure.
b. Write the effects of any five alloying elements on the properties of steel.
c. Explain Iron-Carbon diagram.
d. Explain various case hardening methods.
S.B. Roll No………………………………………….
ENGINEERING MATERIALS
3rd Exam/Mech./3053/Feb'2021
(For 2018 batch onwards)
Duration: 1.15Hrs. M.Marks:25
SECTION-A
Q1. Attempt any three questions. 3x5=15
a. Explain Nitriding Process with its merit and demerits.
b. Difference between Hot working and Cold working process.
c. State the effects of adding the following alloying elements to steel: Nickel, Chromium, Manganese,
Vanadium, Tungsten, Silicon and Copper.
d. Explain High Speed Steel, Stainless Steel, Spring Steel and Silicon Steel.
e. How do Thermoplastics differ from thermosetting materials?
f. What are the special properties of plastics that make them useful engineering materials?
g. What is the difference between Normalising and Quenching?
SECTION-B
Q2. Attempt any one question. 1x10=10
i. Explain the various types of Annealing Process.
ii. Explain Iron-Carbon Equilibrium Diagram with Sketch.
iii. Classify the Ceramics and explain its properties and applications.
iv. Explain the behavior of Mild steel under load using Stress-Strain Diagram.
S.B. Roll No………………………………………….
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Classify the different types of analog instrument.
b. Explain the working of CRO with diagram.
c. Define the following terms: Accuracy, Precision, Sensitivity, Resolution, and Range.
d. Explain the working of repulsion type moving iron instrument. Derive the expression for torque
produced.
S.B. Roll No………………………………………….
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Draw the block diagram of C.R.O and explain the function of each block in detail.
b. Write down the working and Operation of LVDT in detail.
c. Write a short note on
i) Loading effect. ii) Precision iii) Accuracy iv) Sensitivity.
d. Explain in detail the working of digital multi-meter and its applications.
S.B. Roll No………………………………………….
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Explain various phases of SDLC.
b. What is DFD? Explain various symbols used in DFD. List and Explain rules for drawing logical DFD.
c. What is testing? Explain various types of testing techniques in detail.
d. What is feasibility study? Explain technical, economic and behavioral feasibility study.
S.B. Roll No………………………………………….
SOFTWARE ENGINEERING
3rd Exam/CSE/IT/0095/Feb'2021
(For 2018 batch onwards)
Duration:1.15Hrs. M.Marks:25
SECTION-A
Q1. Attempt any three questions. 3x5=15
i. What is System? Name its Characteristics.
ii. Explain different activities in system maintenance.
iii. Write a short note on Development process models.
iv. Explain Economic Feasibility. Explain relation between technical and economical feasibility.
v. What are the advantages and disadvantages of Interviews?
vi. Explain data Dictionary. What are its advantages?
vii. Differentiate between Black BOX testing and White Box testing.
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Define System and Explain Various types of Systems
b. Explain SDLC and its different phases.
c. i) Explain Decision Tables b) Decision Tree
d. What are various types of TESTS done on system? Explain in detail.
e. What do you mean by DFD? List and explain rules for drawing logical DFD.
S.B. Roll No………………………………………….
AUTO ENGINE-I
3rd Exam/Auto/0934/Feb'2021
Duration: 1.15Hrs. M.Marks:25
SECTION-A
Q1. Attempt any three questions. 3x5=15
i. Classify engines on the basis of different categories.
ii. Discuss about magneto ignition system with neat sketch.
iii. Explain the terms: - mean effective pressure, relative efficiency, and volumetric efficiency.
iv. Describe briefly the characteristics of lubricants required for automobile engines.
v. Explain splash type lubrication system with sketch.
vi. What is cooling system? Explain Thermo-syphon type cooling system with neat sketch.
vii. Write down the working of 2-stroke engine with neat sketch.
SECTION-B
Q2. Attempt any one question. 1x10=10
a. Explain in details the working of multipoint fuel injection system (MPFI). Also give its merits and
demerits.
b. Explain the working of simple carburetor with neat sketches.
c. What is crankcase ventilation? Describe the various lubrication systems used in automotive engines.
S.B. Roll No………………………………………….
Fig .1