Professional Documents
Culture Documents
cleansave
Contrast Training For Power and Explosiveness by Andrew Sacks |
by Andrew Sacks |
t-nation.com
Building explosive strength is key to reaching full potential in the weight room.
Contrast sets consist of a heavy lift followed by an explosive movement that mimics the mechanics of the heavy
lift.
Performing an explosive movement directly after a heavy resistance exercise causes post activation potentiation
(PAP), which increases explosiveness in high velocity movements.
What's a Contrast Set and Why Should I Do It?
Contrast sets consist of a heavy resisted exercise paired with an unweighted explosive exercise. The two
exercises share a common movement pattern, like squats and vertical jumps.
Performing a maximal or near-maximal muscular contraction before an explosive movement causes post-
activation potentiation (PAP), which allows for a more powerful explosive movement.
The ability to apply force quickly can mean the difference between a successful PR and a lift that stalls halfway
and results in a miss. In a squat competition, I'll put my money on the guy who explodes out of the hole with
authority versus the guy who has trouble generating force quickly.
Louie Simmons includes speed work as an integral part of his programs because it enables you to lift more
weight. For guys that don't have time to do separate Dynamic and Max Effort Days, contrast sets are a way to
build power while still getting heavy strength work at the same time.
We're not 100% sure yet. According to Bret Contreras, the potential mechanisms that cause PAP include
phosphorylation of myosin regulatory light chains, increased recruitment of higher order motor units, and
changes in pennation angle. Studies have also suggested that PAP is caused by increased synaptic excitation in
the spinal cord.
What we do know is that PAP increases the force exerted by a muscle due to its previous contraction. According
to scientist and Supertraining author Yuri Verkhoshanksy, the effect of PAP is like "lifting a half-can of water
when you think it's full."
Depending on the athlete's goals, we have two different variations of high-velocity contrast movements.
Rate of Force Development (RFD). RFD refers to the body's ability to accelerate from a standstill (similar to
starting strength). An example would be jumping from a seated position.
Elastic explosiveness. Refers to the body's ability to generate force by way of the stretch shortening cycle
through a countermovement. An example of this would be a squat jump in which the athlete flexes his hip and
knees quickly before jumping.
There's a simple test to determine which type of contrast movement will benefit you the most. Simply perform 3
vertical jumps, one with a normal countermovement, one with a paused start, and a depth jump from a 12-18
inch box.
If your paused jump is significantly lower than your normal jump (85% or less), you need to improve your
RFD.
If your depth jump is equal to or lower than your normal jump, you need to work on elastic explosiveness.
The depth jump should allow for a higher jump due to the effect of the stretch shortening cycle, so if your depth
jump isn't higher than your standing vertical jump, it means your muscles aren't effectively harnessing the
energy created by the drop from the box.
For each contrast set, the weight should be at or above 90% of 1RM so that the lifter performs 1-3 reps of the
heavy lift followed by 3-6 reps of the high-velocity movement.
Keeping the volume low during the heavy lift will lessen the effect of fatigue and allow for maximum force
production during the explosive movement while maximizing the effects of PAP.
You should add a 30-second rest interval between the heavy lift set and the explosive movement. This gives the
involved muscles time to recover, while still allowing the lifter to take advantage of PAP from the heavy lift.
Also, the addition of a 15-second rest after each rep of the explosive movement will allow for maximum
velocity on each rep. After finishing your explosive reps, rest for 3 minutes before the next set.
Since it's unwise to start off by throwing 90% of your 1RM around, include 3-5 warm-up sets before piling the
weight on. However, to avoid muscle fatigue before the work sets, only do enough warm-up reps to get your
blood flowing.
Three warm-up sets of 3-5 reps seems to work well, though advanced lifters dealing with very heavy weights
may need a fourth and fifth warm-up set.
For easy transition from heavy squats to speed squats, set up the bar so that your speed squat weight is on the
inside of the bar, and then add the extra weight to the bar so that the total weight is equal to your weight for
heavy squats. After completing your heavy set, simply strip the extra weights off the bar so that only the speed
squat total remains.
For example, if your max squat is 395 pounds, set up the bar with a 45-pound plate and a 35-pound plate on
each side, giving you 205 pounds on the bar. If you're doing a heavy set at 95% of your max (375), add another
170 pounds to the bar.
Then after doing the heavy set, strip off the extra 170 pounds and do the speed squats with 205. Taking off the
extra weight by yourself takes about 30-45 seconds, which is a good rest interval between heavy and explosive
movements.
If your goal is to improve rate of force development, pair speed box squats with your heavy squat. To do speed
box squats, simply sit onto a box that's set at or slightly below parallel. Come to a complete stop and then
explode up, squatting the weight as fast as possible.
To improve rate of force development, pair heavy deadlifts with explosive pull-throughs. Stand with your feet
slightly wider than shoulder width, holding a rope attached to a cable. Reach back between your legs while
maintaining a flat back.
If you don't have access to heavy kettlebells (at least 32 kilos), then use heavy dumbbells in their place.
Start with a 70-pound dumbbell and progress from there as your form allows.
The med ball chest press is a great choice to pair with the bench press, but if you don't have access to medicine
balls, plyo push-ups will also work.
To improve RFD, start with the med ball on your chest at a standstill, relax completely, then explosively chest
pass the ball upwards as hard as you can.
Choosing the weight of the medicine ball depends on the individual. Make sure to choose a weight that you can
throw with consistent velocity throughout the entirety of the set. It should be a weight that's challenging to
move fast, but not prohibitively so.
Contrast sets are best done at the start of your session. If your program already includes a day for squatting,
deadlifting, and benching, simply replace your regular sets with contrast sets.
To increase training density, it's a good idea to include a set of mobility work or other active recovery exercise
during the 3 minute rest periods between contrast sets.
Offseason athletes should use contrast sets for 3-4 weeks at a time, usually once per offseason. I don't like the
idea of doing explosive work during the competitive season. By saving them for the offseason, we're able to
develop explosiveness without sacrificing strength gains.
For those training solely to increase the big lifts, work contrast sets into your program every 3 months or so,
depending on your needs. Guys who feel they need to drastically increase their explosiveness could benefit
from using them every one or two months.