Professional Documents
Culture Documents
c VICTOR E. SAOUMA,
Fall 2001
Contents
1 INTRODUCTION 1–1
1.1 Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1.1 Concrete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1.1.1 Mix Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1.1.1.1 Constituents . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1.1.1.2 Preliminary Considerations . . . . . . . . . . . . . . . . 1–5
1.1.1.1.3 Mix procedure . . . . . . . . . . . . . . . . . . . . . . . 1–5
1.1.1.1.4 Mix Design Example . . . . . . . . . . . . . . . . . . . 1–8
1.1.1.2 Mechanical Properties . . . . . . . . . . . . . . . . . . . . . . . . 1–9
1.1.2 Reinforcing Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13
1.2 Design Philosophy, USD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
1.3 Analysis vs Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–15
1.4 Basic Relations and Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–16
1.5 ACI Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–16
2 FLEXURE 2–1
2.1 Uncracked Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
E 2-1 Uncracked Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
2.2 Section Cracked, Stresses Elastic . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
2.2.1 Basic Relations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
2.2.2 Working Stress Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
E 2-2 Cracked Elastic Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
E 2-3 Working Stress Design Method; Analysis . . . . . . . . . . . . . . . . . . . 2–6
E 2-4 Working Stress Design Method; Design . . . . . . . . . . . . . . . . . . . 2–7
2.3 Cracked Section, Ultimate Strength Design Method . . . . . . . . . . . . . . . . . 2–8
2.3.1 Whitney Stress Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.3.2 Balanced Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
2.3.3 Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
2.3.4 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
2.4 Practical Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
2.4.1 Minimum Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
2.4.2 Beam Sizes, Bar Spacing, Concrete Cover . . . . . . . . . . . . . . . . . . 2–13
2.4.3 Design Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13
2.5 USD Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–15
E 2-5 Ultimate Strength; Review . . . . . . . . . . . . . . . . . . . . . . . . . . 2–15
E 2-6 Ultimate Strength; Design I . . . . . . . . . . . . . . . . . . . . . . . . . . 2–16
E 2-7 Ultimate Strength; Design II . . . . . . . . . . . . . . . . . . . . . . . . . 2–17
Draft
0–2
. . . . . . 2–17
2.6.1 Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–19
2.6.2 Design, (balanced) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–19
E 2-8 T Beam; Moment Capacity I . . . . . . . . . . . . . . . . . . . . . . . . . 2–20
E 2-9 T Beam; Moment Capacity II . . . . . . . . . . . . . . . . . . . . . . . . . 2–21
E 2-10 T Beam; Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–22
2.7 Doubly Reinforced Rectangular Beams . . . . . . . . . . . . . . . . . . . . . . . . 2–23
2.7.1 Tests for fs and fs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–24
2.7.2 Moment Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–26
E 2-11 Doubly Reinforced Concrete beam; Review . . . . . . . . . . . . . . . . . 2–28
E 2-12 Doubly Reinforced Concrete beam; Design . . . . . . . . . . . . . . . . . . 2–30
2.8 Bond & Development Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–31
2.8.1 Moment Capacity Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2–35
3 SHEAR 3–1
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.2 Shear Strength of Uncracked Section . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
3.3 Shear Strength of Cracked Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
3.4 ACI Code Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
3.5 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
E 3-1 Shear Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
3.6 Shear Friction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
E 3-2 Shear Friction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
3.7 Brackets and Corbels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
3.8 Deep Beams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–12
5 SERVICEABILITY 5–1
5.1 Control of Cracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
E 5-1 Crack Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
5.2 Deflections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–4
5.2.1 Short Term Deflection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–4
5.2.2 Long Term Deflection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
E 5-2 Deflections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
6–1
6.1 Vertical Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
6.2 Horizontal Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4
6.2.1 Portal Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4
E 6-1 Approximate Analysis of a Frame subjected to Vertical and Horizontal
Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
8 COLUMNS 8–1
9 COLUMNS 9–1
9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
9.1.1 Types of Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
9.1.2 Possible Arrangement of Bars . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
9.2 Short Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–3
9.2.1 Concentric Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–3
9.2.2 Eccentric Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–3
9.2.2.1 Balanced Condition . . . . . . . . . . . . . . . . . . . . . . . . . 9–4
9.2.2.2 Tension Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–5
9.2.2.3 Compression Failure . . . . . . . . . . . . . . . . . . . . . . . . . 9–6
9.2.3 ACI Provisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–7
9.2.4 Interaction Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–8
9.2.5 Design Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–8
E 9-1 R/C Column, c known . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–8
E 9-2 R/C Column, e known . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–10
E 9-3 R/C Column, Using Design Charts . . . . . . . . . . . . . . . . . . . . . . 9–14
9.2.6 Biaxial Bending . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–15
E 9-4 Biaxially Loaded Column . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–18
9.3 Long Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–19
9.3.1 Euler Elastic Buckling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–19
9.3.2 Effective Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–20
9.3.3 Moment Magnification Factor; ACI Provisions . . . . . . . . . . . . . . . 9–22
E 9-5 Long R/C Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–25
E 9-6 Design of Slender Column . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–26
. . . . . . 10–8
10.3 Case Study: Walnut Lane Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–10
10.3.1 Cross-Section Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–12
10.3.2 Prestressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–12
10.3.3 Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–13
10.3.4 Flexural Stresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–13
11 FOOTINGS 11–1
List of Figures
. . . . . . . . 3–3
3.5 Shear Strength of Uncracked Section . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
3.6 Free Body Diagram of a R/C Section with a Flexural Shear Crack . . . . . . . . 3–5
3.7 Equilibrium of Shear Forces in Cracked Section . . . . . . . . . . . . . . . . . . . 3–5
3.8 Summary of ACI Code Requirements for Shear . . . . . . . . . . . . . . . . . . . 3–7
3.9 Corbel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
3.10 Shear Friction Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
3.11 Shear Friction Across Inclined Reinforcement . . . . . . . . . . . . . . . . . . . . 3–10
6.1 Approximate Analysis of Frames Subjected to Vertical Loads; Girder Moments . 6–2
6.2 Approximate Analysis of Frames Subjected to Vertical Loads; Column Axial Forces6–3
6.3 Approximate Analysis of Frames Subjected to Vertical Loads; Column Moments 6–3
6.4 Approximate Analysis of Frames Subjected to Lateral Loads; Column Shear . . . 6–5
6.5 Approximate Analysis of Frames Subjected to Lateral Loads; Girder Moment . . 6–5
6.6 Approximate Analysis of Frames Subjected to Lateral Loads; Column Axial Force6–6
6.7 Example; Approximate Analysis of a Building . . . . . . . . . . . . . . . . . . . . 6–7
6.8 Approximate Analysis of a Building; Moments Due to Vertical Loads . . . . . . . 6–9
6.9 Approximate Analysis of a Building; Shears Due to Vertical Loads . . . . . . . . 6–10
6.10 Approximate Analysis for Vertical Loads; Spread-Sheet Format . . . . . . . . . . 6–12
6.11 Approximate Analysis for Vertical Loads; Equations in Spread-Sheet . . . . . . . 6–13
6.12 Approximate Analysis of a Building; Moments Due to Lateral Loads . . . . . . . 6–14
6.13 Portal Method; Spread-Sheet Format . . . . . . . . . . . . . . . . . . . . . . . . . 6–16
6.14 Portal Method; Equations in Spread-Sheet . . . . . . . . . . . . . . . . . . . . . . 6–17
. 9–4
9.6 Strain and Stress Diagram of a R/C Column . . . . . . . . . . . . . . . . . . . . 9–5
9.7 Column Interaction Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–8
9.8 Failure Surface of a Biaxially Loaded Column . . . . . . . . . . . . . . . . . . . . 9–15
9.9 Load Contour at Plane of Constant Pn , and Nondimensionalized Corresponding
plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–16
9.10 Biaxial Bending Interaction Relations in terms of β . . . . . . . . . . . . . . . . . 9–17
9.11 Bilinear Approximation for Load Contour Design of Biaxially Loaded Columns . 9–17
9.12 Euler Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–19
9.13 Column Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–20
9.14 Critical lengths of columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–21
9.15 Effective length Factors Ψ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–22
9.16 Standard Alignment Chart (ACI) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–23
9.17 Minimum Column Eccentricity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–23
9.18 P-M Magnification Interaction Diagram . . . . . . . . . . . . . . . . . . . . . . . 9–24
List of Tables
1.1 ASTM Sieve Designation’s Nominal Sizes Used for Concrete Aggregates . . . . . 1–3
1.2 ASTM C33 Grading Limits for Coarse Concrete Aggregates . . . . . . . . . . . . 1–3
1.3 ASTM C33 Grading Limits for Fine Concrete Aggregates . . . . . . . . . . . . . 1–3
1.4 Example of Fineness Modulus Determination for Fine Aggregate . . . . . . . . . 1–5
1.5 Recommended Slumps (inches) for Various Types of Construction . . . . . . . . 1–6
1.6 Recommended Average Total Air Content as % For Different Nominal Maximum
Sizes of Aggregates and Levels of Exposure . . . . . . . . . . . . . . . . . . . . . 1–6
1.7 Approximate Mixing Water Requirements, lb/yd3 of Concrete For Different
Slumps and Nominal Maximum Sizes of Aggregates . . . . . . . . . . . . . . . . . 1–7
1.8 Relationship Between Water/Cement Ratio and Compressive Strength . . . . . . 1–7
1.9 Volume of Dry-Rodded Coarse Aggregate per Unit Volume of Concrete for Dif-
ferent Fineness Moduli of Sand . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8
1.10 Creep Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13
1.11 Properties of Reinforcing Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
1.12 Strength Reduction Factors, Φ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
2.1 Total areas for various numbers of reinforcing bars (inch2 ) . . . . . . . . . . . . . 2–14
2.2 Minimum Width (inches) according to ACI Code . . . . . . . . . . . . . . . . . . 2–14
Tentative Schedule
0–3
Fall 1994
1 Aug. 28 Intro; Material
Aug. 30 Concrete mix design
2 Sep. 4 Elastic Uncracked
Sep. 6 WSD; USD singly reinforced
3 Sep. 11 USD singly, examples
Sep. 13 T Beams
4 Sep. 18 T Beams, Doubly Reinf
Sep. 20 Doubly Reinf Development length
5 Sep. 25 Shear
Sep. 27 Shear
6 Oct. 2 TP Lab
Oct. 4 Fall Break
7 Oct. 9 Crack width
Oct. 11 EXAM I
8 Oct. 16 Deflection
Oct. 18 Crack Width-Defelction
9 Oct. 23 Deflection, Continuous Systems
Oct. 25 Continuous Systems; One way slabs
10 Oct. 30 Columns; Intro
Nov. 1 Columns
11 Nov. 6 LAB
Nov. 8 Columns
12 Nov. 13 Biaxial bending
Nov. 15 Long column
13 Nov. 20 Lab
Nov. 22 Thanksgiving
Chapter 1
INTRODUCTION
1.1 Material
1.1.1 Concrete
This section is adapted from Concrete by Mindess and Young, Prentice Hall, 1981
1 Concrete is a mixture of Portland cement, water, and aggregates (usually sand and crushed
stone).
2 Portland cement is a mixture of calcareous and argillaceous materials which are calcined in
a kiln and then pulverized. When mixed with water, cement hardens through a process called
hydration.
3 Ideal mixture is one in which:
1. A minimum amount of cement-water paste is used to fill the interstices between the
particles of aggregates.
2. A minimum amount of water is provided to complete the chemical reaction with cement.
Strictly speaking, a water/cement ratio of about 0.25 is needed to complete this reaction,
but then the concrete will have a very low “workability”.
In such a mixture, about 3/4 of the volume is constituted by the aggregates, and the remaining
1/4 being the cement paste.
4 Smaller particles up to 1/4 in. in size are called fine aggregates, and the larger ones being
coarse aggregates.
5 Portland Cement has the following ASTM designation
I Normal
111
000
000 11
111 000
111
000 111
00111 000 11
00
00111
11 11
00
00
11 111
000
000 11
111
0
1 11
00
00
11
INTRODUCTION
00
11
00000 00
111
000 0000
1111
0000
1111 000 0000
1111
0000
1111 000
11100
11 0000
11110
1 000
111 0
1 0000
1111
00
11
0 1111
1 0000 0 1111
00
11 0000
000
111
000
111
0000 111
1111 000
0000
1111
0000
1111
0000
1111 000
111 00
11
000011
111100
111
000
111
000
111 000
111
0000
1111
0000
1111
0000
1111 11
1
0
0
1 000
111
000
111
0000
1111
000
111
000
111
000
111 00
11
001
110
0
1
0000
1111
0000
1111
0000
1111000 111
111 00
11
000
11
00
00
11
000
111
111
000
000
111
0000 111
1111 00
11
1
00
11
00
11
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0001111
111 0000
1111
0000 0000
1111
000
111
0000
111100
11
00
11
000011
0001111
111 0000
1111
0000 0
1
00
11 000
111
0000
1111
000
111
0000
1111
000
11100
11
0000
1111
00
11 0000
1111
00
11
000
111
0
1 000
111
00
11
0000
1111
00
11
0000
1111
0001111
0
1 0000
1111
0000
0
1 0
1
00
11
0000
1111 0000
1111
0000
1111
0000
1111 0000
1111
000
111 00 0000
1111
0000
1111
0000
1111
001111
11 000
111
0000
1111
0000 1111
00 111
11 000
00000000
1111
0000
1111 00
11
000 111
00 1
0
000
0000
1111
0000 111000 0000
1111
0000
1111 0
1
00
11
111 111 00
11
0000 1111
1111 0000
0000
1111 1111 0000
1111
0000
1111 1111 0000
11110000
1111 11 0
1 1111 000
111 0000 1
1111 0
00
11
0000
1111
0000
1111
0000
1111
0000
1111
000
111
0000
1111
0000
1111
0000
1111
000000
11 00
11 00 111
11 000
0000
1111
0000
1111
0000
11110000
1111
0
1 000 000
111 00
11
0000
1111
000
111
000
111 0000
1111
00
11 11
00
0000
1111
0000
1111
0000
1111
0000 1111
1111 0000
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000 111
1111
00
11
000
000
111
000
111
0000
1111
0000
1111
0
1
0000
1111
0
1
0000
1111
0
1
0
1
0
1
00
11
00 1
11
0
1
0
1 000
111
0 111
1 000
000
111
0001
111
0
1
0
0000
1111
0000
1111
00
11
0000
1111
00
11
00
11
00
11
00
11
000
111
0
100
11
00
11
011
1
00
11
00 111
11 000
000
111
000
111
00
11
00
11
00011
00 111 000
111 00
11
0000
1111 0000
1111 0000
1111 0 111 0000
1111 00 111
0000 111
1111 000
000
111 0000
1111 000
111
0000 111
1111 000 000
111 0000
1111 000
111
000
111 000 0000
1111 000
111
000
111 000
000 1111
0000 000 0
1 0111
000
00010 00
11 00111
00000
11
0000
1111
111
000
111
000
111
0000
1111
0000
1111
111
0000111
000
000
111
000
111 00 11
11 00
000
111 1
0
1
0
0000
1111
0
1
11
00 000 111
111
000 1
111
000
111
0 111
1 000 000
0
1
0
1
111 0
1 11
00
11
00000
111
00
11
111
000 11 11
00
000 11
111
000
111
00 111
11 000 00
00
11
00
11
000
11100
11
0000
1111
0000
1111 0000
1111
0000
1111
0000
1111
1111
0000
1111000
111 0000
1111
0000
1111
0000
1111 00
11 0000
1111
0000
1111 00
11 00
11
0000
1111
00
11 000
111
0000
1111
0000
1111
000
111
000
111 000
111 0
1
000
111
0
1 11
00
0000
1111
0000
1111
0000
1111
0000
1111000
111
0000
1111
0000
1111
0000
1111
0000
1111
000
111 0000
1111
0000
1111
000
111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111000
111
000
111
000
111
000
111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0
1
0000
1111
0
1
0
1
00
11
0
1
00
11
000
111
000
111
000
111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0
1
0000
1111
0000
1111
0000
1111
0000
1111
00
11000
111
00111
11000
00 1
11
00
11 0
000
111
000
111
000
111
000
111
000
111
000111
111 000
0000
1111
0000
1111
0000
1111
00
11
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111 0000
1111 0000
1111 0000
1111 0000
1111 0
1 000
111 00
11
0000
1111000
111
0000
1111
000
111 0000
1111 000
111
111
000 0000
1111
0000
1111
000
111
00111
11
0
1
000
111000
000
1110000
1111 01111
0000
0000
1111
1 1
0 00
11 0111
1
000
111000
000111
111 000 001111
0000
0000
1111
11 11
00
0000
1111 0000
1111 000
111 0000
1111 000
111 1 11
0000
111100 000
111 0000
1111 0
1
0000
1111
0000
1111 0000
1111
0000
1111 000
111
000
111
000
111 0000
1111
000
111
0000
1111 00
11 000
111
000
111 00
11
000 111
00
111
11
00 000
11 1111
0
0000
1
0
0000
1111
00 0
11 1 000
111
000
111 00
11
000
1111
0 00
11
1 1111
0 1
0
0000
1
0
0000
1111
000
111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
0000
1111
000
111 111
000 111
000
000
111
0000
1111
000
111
0000
1111
0000
1111
000
111
0000
1111 00
11 000
111
11
00
1
0000
111 00
11
000 111
000
111
111
000
111 000
0000
1111
0
1
0000
1111
0
1 0
1 0
1
0
1
000
111
11
00
11
00000
111 11
00
000 11
111
000
111
000
111 00
11
0000
1111
00
11
0000
1111
0000
11 00
11
00
11
0000
1111 0001111
0000 0000
11110000
1111
00001111
0000 11111
000 0000
11110 1111
1 0000
0
1 1111
0000000
1111
00
1100
11 000
111
0000
1111
111
0000 111
1111 000 0000
1111
0000
1111 000 11
1110000
1111
0000
1111
1111
0000
11110000
1111
0000
1111 00111
11
1
0 00
11
00000
111
000
111
0000
1111
0000
1111 0000
1111
0
1
0000
1111
0
1
00 11
11
11
00 0
1
0 000
111
000
111
0000
1111
0000
1111 00111
11 00
11
000
111
000
0000 111
1111 000
000
111 0000
1111
0001111
0000 000 00
1110000
11110000
1111
0000
11110000
1111
00001111
00 111
11
0000 00000
1100
11000
111
000
111
0000
1111
0000
1111
00
11
0000
1111
0000
1111 0
1 00 00
11 0
1000
111
00
11
0000
1111
0000
1111
0
1
000
111
000
111
00
11
00 000 00
11 00
11
0000
1111
0000
1111 111 0000
1111 000
111
000
111 11110000
1111 000
111
00 11
11
000
111 00001111
1111
00 0000 0
1 000
111
000
1110
1 0000
1111
0
1 000
111
00
11
0000
1111
0000 1111
1111
0000
1111 0000
0000
1111
0000
1111
0000 1111
0000
000
111
11
00
11
000
111
000
111 000
111
0000
1111
000
111
0000
1111
000 1111
0000 000
111
000
111
000
111
000 1
111
000
111
00 1
11
0111
0
1 00
11
000
0
1
0
1
11
00
0 1111
0000
11
00
0000
1111
0000
1111
000
111
00
11
00
11
00011
111
000
111
0 1
1
00111
00
11 000
0
00
11
0
1
0
1
1
0
000
111
1
0
000
111
000
111
1111
0000 1111
1111 0000 0000
1111
0000
1111 00
11
000
111 111
000
111 00
11
0000
1111
0000
1111 000 111
111
000 1
111
000
000 1111
111
0111
000 0000
0000
1111 00
11
00011
111 00111
00
11
000
111
000 000
111
000
111
0000
1111
0000 1111
1111 0000
00
11
000
111
111 00
11
000 1111
0000
000
111
11
00
11
00 000
111
000
111
000 1111
111 0000
1
0
1
0 1
0
1
0
1
0
1
000
11 00
11
000
111
000 00
111 000
111
11 00
00
11 11
00
11
IV Low heat Portland cement, minimizes thermal cracking but must control initial temper-
ature
6 Aggregate usually occupy 70% to 80% of the volume of concrete. They are granular material
derived, for the most part, from natural rock, crushed stone, natural gravels and sands.
7 ASTM C33 (Standard Specifications for Concrete Aggregates) governs the types of rock which
can produce aggregates.
8 The shape can be rounded, irregular, angular, flaky, or elongated.
9 The surface texture can be glassy, smooth, granular, rough, crystalline or honeycombed.
10 The particle size distribution or grading of aggregates is very important as it determines
the amount of paste for a workable concrete, Fig. 1.1. Since cement is the most expensive
component, proper gradation is of paramount importance.
11The grading of an aggregate supply is determined by a sieve analysis. A representative
sample of the aggregate is passed through a stack of sieves aranged in order of decreasing size
opening of the sieve.
12 We divide aggregates in two categories
Coarse aggregate fraction is that retained on the No. 4 sieve, Table 1.1.
13 ASTM C33 sets grading limits for coarse and fine aggregates, Table 1.2 and 1.3 respectively.
14If a concrete does not comply with these limits, than there will be a need for more paste,
and there will be the possibility of aggregate segregation.
15Since aggregates contain some porosity, water can be absorbed. Also water can be retained
on the surface of the particle as a film or moisture. Hence, it is necessary to quantify the
moisture content of the aggregates in order to make adjustments to the water. Because dry
aggregates will remove water from the paste, then the w/c is effectively reduced. On the other
hand moist aggregates may effectively increase the w/c ratio.
ASTM Size
Design. mm in.
Coarse Aggregate
3 in. 75 3
21/2 in. 63 2.5
2 in. 50 2
11/2 in. 37.5 1.5
1 in. 25 1
3/4 in. 19 0.75
1/2 in. 12.5 0.50
3/8 in. 9.5 0.375
Fine Aggregate
No. 4 4.75 0.187
No. 8 2.36 0.0937
No. 16 1.18 0.0469
No. 30 0.60 (600 µm) 0.0234
No. 50 300 µm 0.0124
No. 100 150 µm 0.0059
Table 1.1: ASTM Sieve Designation’s Nominal Sizes Used for Concrete Aggregates
Table 1.2: ASTM C33 Grading Limits for Coarse Concrete Aggregates
Table 1.3: ASTM C33 Grading Limits for Fine Concrete Aggregates
Air-dry (AD): all moisture is removed from the surface, but internal pores are partially full.
Saturated-surface-dry (SSD): All pores are filled with water, but no film of water on the
surface.
Wet: All pores are completely filled with a film of water on the surface.
Absorption capacity (AC): is the maximum amount of water the aggregate can absorb
WSSD − WOD
AC = × 100% (1.1)
WOD
most normal -weight aggregates (fine and coarse) have an absorption capacity in the range
of 1% to 2%.
WW et − WSSD
SM = × 100% (1.2)
WSSD
18 The fineness modulus is a parameter which describe the grading curve and it can be used
to check the uniformity of the grading. It is usually computed for fine aggregates on the basis
of
cumulative percent retained on standard sieves
F.M. = (1.3)
100
where the standard sieves used are No. 100, No. 50, No. 30, No. 16, No. 8, and No. 4, and
3/8 in, 3/4 in, 11/2 in and larger.
19 The fineness modulus for fine aggregate should lie between 2.3 and 3.1 A small number
indicates a fine grading, whereas a large number indicates a coarse material.
20 Table 1.4 illustrates the determination of the fineness modulus.
21 Fineness modulus of fine aggregate is required for mix proportioning since sand gradation
has the largest effect on workability. A fine sand (low fineness modulus) has much higher paste
requirements for good workability.
22 The fineness modulus of coarse aggregate is not used for mix design purposes.
23 no-fines concrete has little cohesiveness in the frsh state and can not be compacted to a
void-free condition. Hence, it will have a low strength, high permeability. Its only advantage is
low density, and high thermal insulation which can be used if structural requirements are not
high.
1. Water/Cement ratio: where the strength in inversely proportional to the water to cement
ratio, approximately expressed as:
A
fc = (1.4)
B 1.5w/c
For fc in psi, A is usually taken as 14,000 and B depends on the type of cement, but may
be taken to be about 4. It should be noted that w/c controls not only the strength, but
also the porosity and hence the durability.
2. Aggregate Grading: In order to minimize the amount of cement paste, we must maximize
the volume of aggregates. This can be achieved through proper packing of the granular
material. The “ideal” grading curve (with minimum voids) is closely approximated by
the Fuller curve q
d
Pt = (1.5)
D
where Pt is the fraction of total solids finer than size d, and D is the maximum particle
size, q is generally taken as 1/2, hence the parabolic grading.
25Before starting the mix design process, the following material properties should be deter-
mined:
1. Slump1 must be selected for the particular job to account for the anticipated method
of handling and placing concrete, Table 1.5 As a general rule, adopt the lowest possible
slump.
2. Maximum aggregate size: in general the largest possible size should be adopted.
However, it should be noted that:
(a) For reinforced concrete, the maximum size may not exceed one-fifth of the mini-
mum dimensions between the forms, or three-fourths of the minimum clear spacing
between bars, or between steel and forms.
(b) For slabs on grade, the maximum size may not exceed one-third the slab depth.
3. Water and Air content Air content will affect workability (some time it is better to
increase air content rather than increasing w/c which will decrease strength). Air content
can be increased through the addition of admixtures. Table 1.6 tabulates recommended
values of air content (obtained through such admixtures) for different conditions (for
instance under severe freezing/thawing air content should be high).
Recommended water requirements are given by Table 1.7.
Sizes of Aggregates
Exposure 3/8 in. 1/2 in. 3/4 in. 1 in. 11/2 in.
Mild 4.5 4.0 3.5 3.5 3.0
Moderate 6.0 5.5 5.0 4.5 4.4
Extreme 7.5 7.0 6.0 6.05 5.5
Table 1.6: Recommended Average Total Air Content as % For Different Nominal Maximum
Sizes of Aggregates and Levels of Exposure
1
The slump test (ASTM C143) is a measure of the shear resistance of concrete to flowing under its own weight.
It is a good indicator of the concrete “workability”. A hollow mold in the form of a frustum of a cone is filled
with concrete in three layers of equal volume. Each layer is rodded 25 times. The mold is then lifted vertically,
and the slump is measured by determining the difference between the height of the mold and the height of the
concrete over the original center of the base of the specimen.
in. 3/8 in. 1/2 in. 3/4 in. 1 in. 11/2 in.
Non-Air-Entrained Concrete
1-2 350 335 315 300 275
3-4 385 365 340 325 300
6-7 410 385 360 340 315
Air-Entrained Concrete
1-2 305 295 280 270 250
3-4 340 325 305 295 275
6-7 365 345 325 310 290
Table 1.7: Approximate Mixing Water Requirements, lb/yd3 of Concrete For Different Slumps
and Nominal Maximum Sizes of Aggregates
4. Water/cement ratio: this is governed by both strength and durability. Table 1.8
provides some guidance in terms of strength.
5. Cement Content: Once the water content and the w/c ratio are determined, the amount
of cement per unit volume of concrete is determined simply by dividing the estimated
water requirement by the w/c ratio.
6. Coarse Aggregate Content: Volume of coarse aggregate required per cubic yard of
concrete depends on its maximum size and the fineness modulus of the fine aggregate,
Table 1.9. The oven dry (OD) volume of coarse aggregate in ft3 required per cubic yard
is simply equal to the value from Table 1.9 multiplied by 27. This volume can then be
converted to an OD weight by multiplying it by the dry-rodded2 weight per cubic foot of
coarse aggregate.
7. The fine aggregate content can be estimated by subtracting the volume of cement,
water, air and coarse aggregate from the total volume. The weight of the fine aggregate
can then be obtained by multiplying this volume by the density of the fine aggregate.
2
Dry Rodded volume (DRV) is the normal volume of space a material occupies.
Table 1.9: Volume of Dry-Rodded Coarse Aggregate per Unit Volume of Concrete for Different
Fineness Moduli of Sand
Concrete is required for an exterior column to be located above ground in an area where
substantial freezing and thawing may occur. The concrete is required to have an average 28-
day compressive strength of 5,000 psi. For the conditions of placement, the slump should be
between 1 and 2 in, the maximum aggregate size should not exceed 3/4 in. and the properties
of the materials are as follows:
Coarse Aggregates: Bulk specific gravity (SSD) = 2.70; absorption capacity= 1.0%; Total
moisture content = 2.5%; Dry-rodded unit weight = 100 lb/ft3
Fine Aggregates: Bulk specific gravity (SSD) = 2.65; absorption capacity = 1.3 %; Total
moisture content=5.5%; fineness modulus = 2.70
The sieve analyses of both the coarse and fine aggregates fall within the specified limits. With
this information, the mix design can proceed:
3. Estimation of mixing water: Because water will be exposed to freeze and thaw, it must
be air-entrained. From Table 1.6 the air content recommended for extreme exposure is
6.0%, and from Table 1.7 the water requirement is 280 lb/yd3
6. Coarse aggregate content, interpolating from Table 1.9 for the fineness modulus of
the fine aggregate of 2.70, the volume of dry-rodded coarse aggregate per unit volume of
concrete is 0.63. Therefore, the coarse aggregate will occupy 0.63 × 27 = 17.01 ft3 /yd3 .
The OD weight of the coarse aggregate is 17.01 × 100 = 1, 701 lb. The SSD weight is
1–9
7. Fine aggregate content Knowing the weights and specific gravities of the water, cement,
and coarse aggregate, and knowing the air volume, we can calculate the volume per yd3
occupied by the different ingredients.
Water 280/62.4 = 4.49 ft3
Cement 700/(3.15)(62.4) = 3.56 ft3
Coarse Aggregate (SSD) 1,718/(2.70)(62.4) = 1.62 ft3
Air (0.06)(27) = 1.62 ft3
19.87 ft3
Hence, the fine aggregate must occupy a volume of 27.0 − 19.87 = 7.13 ft3 . The required
SSD weight of the fine aggregate is 7.13 × 2.65 × 62.4 = 1, 179 lb.
8. Adjustment for moisture in the aggregate. Since the aggregate will be neither SSD or
OD in the field, it is necessary to adjust the aggregate weights for the amount of water
contained in the aggregate. Only surface water need be considered; absorbed water does
not become part of the mix water. For the given moisture contents, the adjusted aggre-
gate weights become:
Surface moisture contributed by the coarse aggregate is 2.5-1.0 = 1.5%; by the fine ag-
gregate: 5.5-1.3 = 4.2%; Hence the additional water required is then
280-1,718(0.015)-1,179(0.042) = 205 lb/yd3 .
Water 205 lb
Cement 700 lb
Wet coarse aggregate 1,744 lb
Wet fine aggregate 1,229 lb
3,878 lb/yd3
3,878
27 143.6 lb/ft3
26 Contrarily to steel to modulus of elasticity of concrete depends on the strength and is given
by
E = 57, 000 fc (1.6)
or
E = 33γ 1.5 fc (1.7)
27
INTRODUCTION
Normal weight and lightweight concrete have γ equal to 150 and 90-120 lb/ft3 respectively.
28 Poisson’s ratio ν = 0.15.
29Typical concrete (compressive) strengths range from 3,000 to 6,000 psi; However high strength
concrete can go up to 14,000 psi.
30 Stress-strain curve depends on
1. Properties of aggregates
2. Properties of cement
3. Water/cement ratio
4. Strength
5. Age of concrete
31 Non-linear part of stress-strain curve is caused by micro-cracking around the aggregates, Fig.
1.2
f’
c
Non-Linear
~ 0.5 cf’
Linear
εu
t
fct = f
4.0 + .85t c,28
or
t (days) 1 2 4 7 10 15
%fc,28 20 35 54 70 80 90
σ
1–11
f’
c
f’ / 2
c
εu = 0.003 ε
35 The tensile strength of concrete ft is very difficult to measure experimentally. Accepted
values
36 Rather than the tensile strength, it is common to measure the modulus of rupture fr , Fig.
1.4
11
00
00
11 11
00
00
11 00
11
00
11
σ
σ
fr ≈ 7.5 fc (1.9)
f’t
INTRODUCTION
f’c
1
f’t
σ2
σ1 σ1
σ2
f’c
3
For this reason a minimum amount of reinforcement is always necessary in concrete, and a 2% reinforcement,
can reduce the shrinkage by 75%.
ε
1–13
Elastic recovery
creep
Creep recovery
Residual
41 Coefficient of thermal expansion is 0.65 × 10−5 /deg F for normal weight concrete.
Weight
(in.) ( in2 ) in lb/ft
No. 2 2/8=0.250 0.05 0.79 0.167
No. 3 3/8=0.375 0.11 1.18 0.376
No. 4 4/8=0.500 0.20 1.57 0.668
No. 5 5/8=0.625 0.31 1.96 1.043
No. 6 6/8=0.750 0.44 2.36 1.5202
No. 7 7/8=0.875 0.60 2.75 2.044
No. 8 8/8=1.000 0.79 3.14 2.670
No. 9 9/8=1.128 1.00 3.54 3.400
No. 10 10/8=1.270 1.27 3.99 4.303
No. 11 11/8=1.410 1.56 4.43 5.313
No. 14 14/8 =1.693 2.25 5.32 7.650
No. 18 18/8 =2.257 4.00 7.09 13.60
49ACI refers to this method as the Strength Design Method, (previously referred to as the
Ultimate Strength Method).
where
Φ is a strength reduction factor, less than 1, and must account for the type of structural
element, Table 1.12 (ACI 9.3.2)
Type of Member Φ
Axial Tension 0.9
Flexure 0.9
Axial Compression, spiral reinforcement 0.75
Axial Compression, other 0.70
Shear and Torsion 0.85
Bearing on concrete 0.70
ΦMn ≥ Mu
ΦVn ≥ Vu
ΦPn ≥ Pu
1. 1.4D+1.7L
2. 0.75(1.4D+1.7L+1.7W)
3. 0.9D+1.3W
4. 1.05D+1.275W
5. 0.9D+1.7H
6. 1.4D +1.7L+1.7H
7. 0.75(1.4D+1.4T+1.7L)
8. 1.4(D+T)
where D= dead; L= live; Lr= roof live; W= wind; E= earthquake; S= snow; T= temperature;
H= soil. We must select the one with the largest limit state load.
52 Serviceability Limit States must be assessed under service loads (not factored). The
1. Deflections
3. Stability
Analysis: Given a certain design, determine what is the maximum moment which can be
applied.
Design: Given an external moment to be resisted, determine cross sectional dimensions (b and
h) as well as reinforcement (As ). Note that in many cases the external dimensions of the
beam (b and h) are fixed by the architect.
54 We often consider the maximum moment along a member, and design accordingly.
55 In developing a design/analysis method for reinforced concrete, the following basic relations
will be used:
1. Equilibrium: of forces and moment at the cross section. 1) ΣFx = 0 or Tension in the
reinforcement = Compression in concrete; and 2) ΣM = 0 or external moment (that is the
one obtained from the moment envelope) equal and opposite to the internal one (tension
in steel and compression of the concrete).
2. Material Stress Strain: We recall that all normal strength concrete have a failure strain
#u = .003 in compression irrespective of fc .
Plane section remain plane ⇒ strain is proportional to distance from neutral axis.
U = 1.4D + 1.7L
9.2.2 - If resistance to structural effects of a specified wind load W are included in design,
the following combinations of D, L, and W shall be investigated to determine the greatest
required strength U
U = 0.75(1.4D + 1.7L + 1.7W )
where load combinations shall include both full value and zero value of L to determine the more
severe condition, and
U = 0.9D + 1.3W
but for any combination of D, L, and W, required strength U shall not be less than Eq. (9-1).
9.3.1 - Design strength provided by a member, its connections to other members, and its
cross sections, in terms of flexure, axial load, shear, and torsion, shall be taken as the nominal
strength calculated in accordance with requirements and assumptions of this code, multiplied
by a strength reduction factor Φ.
9.3.2 - Strength reduction factor Φ shall be as follows:
9.3.2.1 - Flexure, without axial load 0.90
9.4 - Design strength for reinforcement Designs shall not be based on a yield strength of
reinforcement fy in excess of 80,000 psi, except for prestressing tendons.
10.2.2 - Strain in reinforcement and concrete shall be assumed directly proportional to
the distance from the neutral axis, except, for deep flexural members with overall depth to
clear span ratios greater than 2/5 for continuous spans and 4/5 for simple spans, a non-linear
distribution of strain shall be considered. See Section 10.7.
10.2.3 - Maximum usable strain at extreme concrete compression fiber shall be assumed
equal to 0.003.
10.2.4 - Stress in reinforcement below specified yield strength fy for grade of reinforcement
used shall be taken as Es times steel strain. For strains greater than that corresponding to fy ,
stress in reinforcement shall be considered independent of strain and equal to fy .
10.2.5 - Tensile strength of concrete shall be neglected in flexural calculations of reinforced
concrete, except when meeting requirements of Section 18.4.
10.2.6 - Relationship between concrete compressive stress distribution and concrete strain
may be assumed to be rectangular, trapezoidal, parabolic, or any other shape that results in
prediction of strength in substantial agreement with results of comprehensive tests.
10.2.7 - Requirements of Section 10.2.5 may be considered satisfied by an equivalent rect-
angular concrete stress distribution defined by the following:
10.2.7.1 - Concrete stress of 0.85fc shall be assumed uniformly distributed over an equiva-
lent compression zone bounded by edges of the cross section and a straight line located parallel
to the neutral axis at a distance (a = β1 c) from the fiber of maximum compressive strain.
10.2.7.2 - Distance c from fiber of maximum strain to the neutral axis shall be measured
in a direction perpendicular to that axis.
10.2.7.3 - Factor β1 shall be taken as 0.85 for concrete strengths fc up to and including
4,000 psi. For strengths above 4,000 psi, β1 shall be reduced continuously at a rate of 0.05 for
each 1000 psi of strength in excess of 4,000 psi, but β1 shall not be taken less than 0.65.
10.3.2 - Balanced strain conditions exist at a cross section when tension reinforcement
reaches the strain corresponding to its specified yield strength fy just as concrete in compression
reaches its assumed ultimate strain of 0.003.
10.3.3 - For flexural members, and for members subject to combined flexure and compres-
sive axial load when the design axial load strength (ΦPn ) is less than the smaller of (0.10fc Ag )
or (ΦPb ), the ratio of reinforcement p provided shall not exceed 0.75 of the ratio ρb that would
produce balanced strain conditions for the section under flexure without axial load. For mem-
bers with compression reinforcement, the portion of ρb equalized by compression reinforcement
need not be reduced by the 0.75 factor.
10.3.4 - Compression reinforcement in conjunction with additional tension reinforcement
may be used to increase the strength of flexural members.
10.5.1 - At any section of a flexural member, except as provided in Sections 10.5.2 and
10.5.3, where positive reinforcement is required by analysis, the ratio ρ provided shall not be
less than that given by
200
ρmin =
fy
Chapter 2
FLEXURE
1 This is probably the longest chapter in the notes, we shall cover in great details flexural
design/analysis of R/C beams starting with uncracked section to failure conditions.
3. Ultimate (failure)
h d
As
εs
2 Assuming perfect bond between steel and concrete, we have εs = εc Fig. 2.1
fs fc Es
ε s = εc ⇒ = ⇒ fs = fc ⇒ fs = nfc (2.1)
Es Ec Ec
Es
where n is the modular ratio n = Ec
11111111111111111
00000000000000000
00000000000000000
11111111111111111
FLEXURE
00000000000000000
11111111111111111
00000000000000000
11111111111111111
00000000000000000
11111111111111111
00000000000000000
11111111111111111
00000000000000000
11111111111111111
00000000000000000
11111111111111111
00000000000000000
11111111111111111
(n-1)A S 11111111111111111
00000000000000000
00000000000000000
11111111111111111 (n-1)A S
00000000000000000
11111111111111111
2 00000000000000000
11111111111111111
00000000000000000
11111111111111111 2
00000000000000000
11111111111111111
6
+
Make sure that σmax < ft
Given fc = 4,000 psi; ft = 475 psi; fy = 60,000 psi; M = 45 ft-k = 540,000 in-lb; As = 2.35
in2
+ , f − , and f
Determine fmax max s
yt
25" 23"
2
yb
As = 2.35 in
10"
Solution:
29, 000
n = √ = 8 ⇒ (n − 1)As = (8 − 1)(2.35) = 16.45 in2 (2.3-a)
57 4, 000
(10)(25)( 25
2 ) + (16.45)(2)
yb = (2.3-b)
(25)(10) + 16.45
yb = 11.8 in (2.3-c)
y t = 25 − 11.8 = 13.2 in (2.3-d)
(10)(25)3
I = + (25)(10)(13.2 − 12.5)2 + (16.45)(23 − 13.2)2 (2.3-e)
12
= 14, 722 in2 (2.3-f)
Mc (540, 000) lb.in(13.2)in
fcc = = = 484 psi (2.3-g)
I (14, 722) in4
fct = = 4
= 433 psi < 475 psi (2.3-h)
I (14, 722) in
Mc (540, 000)(23 − 13.2) in
fs = n = (8) = 2, 876 psi (2.3-i)
I (14, 722)
7 This is important not only as an acceptable alternative ACI design method, but also for the
8If fct > fr , fcc <≈ .5fc and fs < fy we will assume that the crack goes all the way to the
N.A and we will use the transformed section, Fig. 2.3
fc
11111111111111111
00000000000000000 111111111
000000000
00000000000000000
11111111111111111 000000000
111111111 kd/3
00000000000000000
11111111111111111 000000000
111111111 C
00000000000000000
11111111111111111 000000000
111111111 kd
00000000000000000
11111111111111111 000000000
111111111
00000000000000000
11111111111111111 000000000
111111111 d
00000000000000000
11111111111111111 000000000
111111111
00000000000000000
11111111111111111 000000000
111111111 (1-k/3)d=jd
00000000000000000
11111111111111111
(n-1)A S 11111111111111111
00000000000000000
00000000000000000
11111111111111111 (n-1)A S
00000000000000000
11111111111111111 11111111111111111
00000000000000000 T
00000000000000000
11111111111111111 00000000000000000
11111111111111111
2
00000000000000000
11111111111111111 2
00000000000000000
11111111111111111
00000000000000000
11111111111111111
b
9 To locate N.A, tension force = compressive force (by def. NA) (Note, for linear stress distri-
bution and with ΣFx = 0; σ = by ⇒ bydA = 0, thus b ydA = 0 and ydA = yA = 0, by
definition, gives the location of the neutral axis)
Es
10 Note, N.A. location depends only on geometry & n
Ec
11 Tensile and compressive forces are equal to C = bkd 2 fc & T = As fs and neutral axis is
determined by equating the moment of the tension area to the moment of the compression
area
kd
b(kd) = nAs (d − kd) 2nd degree equation (2.4-a)
2
M
M = T jd = As fs jd ⇒ fs (2.4-b)
As jd
bkd bd2 M
M = Cjd = fc jd = kjfc ⇒ fc = 1 2 (2.4-c)
2 2 2 bd kj
where j = (1 − k/3).
12 Referred to as Alternate Design Method (ACI Code Appendix A); Based on Working
Stress Design method.
13 Places a limit on stresses and uses service loads (ACI A.3).
fcc ≤ .45fc
fst ≤ 20 ksi for grade 40 or 50 steel (2.5)
fst ≤ 24 ksi for grade 60 steel
Design: Objective is to have fc & fs preset & determine As , Fig. 2.4, and we thus seek the
optimal value of k in such a way that concrete and steel reach their respective limits
simultaneously.
εc fc
C kd/3
kd
d
(1-k/3)d=jd
T
εs fs
εc
= kd
εs d−kd f c Es
= k
fc Ec f s 1−k n
εc = Es k= (2.7)
Ec
n =
n+r
εs = fs
Es
Ec
fs
r = fc
15 Balanced design in terms of ρ: What is the value of ρ such that steel and concrete will both
C = bkd
2 fc
fc
T = As fs 2 bkd = ρb fs bd n
ρb = (2.8-a)
C = T
n
k = n+r 2r(n+r)
ρ = Abds
Victor Saouma Mechanics and Design of Reinforced Concrete
Draft
2.2 Section Cracked, Stresses Elastic 2–5
16 Governing equations
M = As fs jd (2.9)
where
k = 2ρn + (ρn)2 − ρn
Design We define
1
R = fc kj (2.12)
2
solve for bd2 from
M
bd2 = (2.13)
R
assume b and solve for d. Finally we can determine As from
As = ρb bd (2.14)
17 Summary
Review Design
√ √
b, d, As M
M? b, d, As ?
ρ = Abds k = n+r n
j = 1 − k3
k = 2ρn + (ρn)2 − ρn r = ffsc
r = ffsc R = 12 fc kj
n n
ρb = 2r(n+r) ρb = 2r(n+r)
ρ < ρb M = As fs jd bd2 = M R
ρ > ρb M = 12 fc bkd2 j As = ρb bd or As = M
fs jd
Same problem as example 2.1 fc = 4,000 psi; ft = 475 psi; fy = 60,000 psi; As = 2.35 in2
FLEXURE
Based on previous example, fct would be 866 psi >> fr and the solution is thus no longer
valid.
The neutral axis is obtained from
As 2.35
ρ = = = 0.0102 (2.15-a)
bd (10)(23)
ρn = (0.010)(8) = 0.08174 (2.15-b)
k = 2ρn + (ρn)2 − ρn (2.15-c)
= 2(0.08174) + (0.08174)2 − (0.08174) = 0.33 (2.15-d)
kd = (.33)(23) = 7.6 in (2.15-e)
0.33
jd = 1− (23) = 20.47 in (2.15-f)
3
M
fs = (2.15-g)
As jd
(90)(1, 000)(12)
= = 22, 400 psi (2.15-h)
(2.35)(20.47)
2M
fc = (2.15-i)
bjkd2
(2)(90)(12, 000)
= = 1, 390 psi (2.15-j)
(10) (20.47) (7.6)
jd kd
2
(10)(7.6)3 7.6
I = + (10)(7.6) + 8(2.35)(23 − 7.6)2 = 5, 922 in4 (2.15-k)
12 2
Same problem as example 2.1 fc = 4,000 psi; ft = 475 psi; fy = 60,000 psi; As = 2.35 in2 .
Determine Moment capacity.
Solution:
As 2.35
ρ = = = .0102 (2.16-a)
bd (10)(23)
fs = 24 ksi (2.16-b)
fc = (.45)(4, 000) = 1, 800 psi (2.16-c)
k = 2ρn + (ρn)2 − ρn = 2(.0102)8 + (.0102)2 − (8)(.0102) = .331 (2.16-d)
k
j = 1 − = .889 (2.16-e)
3
N.A. @ (.331)(23) = 7.61 in (2.16-f)
n 8
ρb = = = .014 > ρ ⇒ Steel reaches elastic (2.16-g)
limit
2r(n + r) (2)(13.33)(8 + 13.33)
M = As fs jd = (2.35)(24)(.889)(23) = 1, 154 k.in = 96 k.ft (2.16-h)
Note, had we used the alternate equation for moment (wrong) we would have overestimated
the design moment:
1
M = = fc bkd2 j (2.17-a)
2
1
= (1.8)(10)(0.33)(0.89)(23)2 = 1, 397 k.in > 1, 154 k.in (2.17-b)
2
If we define αc = fc /1, 800 and αs = fs /24, 000, then as the load increases both αc and αs
increase, but at different rates, one of them αs reaches 1 before the other.
αs αc
1
Load
Design a beam to carry LL = 1.9 k/ft, DL = 1.0 k/ft with fc = 4, 000 psi, fy = 60, 000 psi,
L = 32 ft.
Solution:
(2.18-b)
Es 29, 000
n = = √ =8 (2.18-c)
Ec 57 4, 000
fs 24
r = = = 13.33 (2.18-d)
fc 1.8
n 8
k = = = .375 (2.18-e)
n+r 8 + 13.33
d .375
j = 1− =1− = .875 (2.18-f)
3 3
1 1
R = fc kj = (1, 800)(.375)(.875) = 295 psi (2.18-g)
2 2
n 8
ρb = = = .01405 (2.18-h)
2r(n + r) 2(13.33)(8 + 13.33)
(32)2
M = [(1.9) + (1.0 + .5)] = 435 k.ft (2.19-a)
8
M 435 k.ft in2 (12, 000) lb.in
bd2 = = = 17, 700 in3 (2.19-b)
R (295) lbs ft k
ε
γ f’c
βc a/2 = β c
c= a a
c β1
C=α f’cb
c C=γ f’ab
c
h d
As
fs fs
ε Actual
b
Figure
18 At failure we have, linear cross strain distribution (ACI 10.2.2) (except for deep beams),
non-linear stress strain curve for the concrete, thus a non-linear stress distribution.
19 Two options:
2. Replace exact stress diagram with a simpler and equivalent one, (ACI 10.2.6)
Thus
α
γ= (2.21)
β1
But the location of the resultant forces must be the same, hence
β1 = 2β (2.22)
21 From Experiments
a= β1c
C=0.85f’c ab
c
h d
d
As
εs T
Compression Failure:
εc = .003 (2.25-a)
fs
εs = (2.25-b)
Es
c .003
= ⇒ c= fs
.003
d (2.25-c)
d .003 + εs Es
+.003
Balanced Design:
24Balanced design occurs if we have simultaneous yielding of the steel and crushing of the
concrete. Hence, we simply equate the previous two equations
ρfy .003
ρbf 2d .003
.85fc β1 d = fs +.003
d
.85fc β1 = fs +.003
d ρb = .85β1 ffyc 87,000+f
87,000
Es E−s y (2.26-a)
ρ = ρb Es = 29, 000 ksi (ACI 8.4.3)
200
ρmin ≥ (ACI 10.5.1) (2.29)
fy
2.3.3 Review
ρact = Abds
(2.30)
ρb = (.85)β1 ffyc 87+f
87
y
s y A f
a = .85f ΣFx = 0
cb (2.31)
Md = φAs fy (d − a2 ) ΣM = 0
• ρact > ρb is not allowed by code, in this case we have an extra unknown fs .
31 We now have one more unknown fs , and we will need an additional equation (from strain
diagram).
As f s
c = .85f ΣFx = 0
c bβ1
c .003 (2.32)
d = .003+εs From strain diagram
β1 c
Md = φAs fs (d − 2 ) ΣM = 0
2.3.4 Design
or
fy
R = ρfy 1 − .59ρ (2.34)
fc
which does not depend on unknown quantities. Then solve for bd2 :
FLEXURE
Md
bd2 = (2.35)
ΦR
Solve for b and d (this will require either an assumption on one of the two, or on their
ratio).
As = ρbd
II b & d known & Md known ⇒ there is no assurance that we can have a design with ρb
If the section is too small, then it will require too much steel resulting in an over-reinforced
section.
Iterative approach
(a) Since we do not know if the steel will be yielding or not, use fs .
(b) Assume an initial value for a (a good start is a = d5 )
(c) Assume initially that fs = fy
(d) Check equilibrium of moments (ΣM = 0)
M
As = d (2.36)
Φfs d − a2
36 Reinforcing bars
1. Minimum spacing between bars, and minimum covers are needed to
(a) Prevent Honeycombing of concrete (air pockets)
(b) Concrete (usually up to 3/4 in MSA) must pass through the reinforcement
(c) Protect reinforcement against corrosion and fire
2. Use at least 2 bars for flexural reinforcement
3. Use bars #11 or smaller for beams.
4. Use no more than two bar sizes and no more than 2 standard sizes apart (i.e #7 and #9
acceptable; #7 and #8 or #7 and #10 not).
5. Use no more than 5 or 6 bars in one layer.
6. Place longest bars in the layer nearest to face of beam.
7. Clear distance between parallel bars not less that db (to avoid splitting cracks) nor 1 in.
(to allow concrete to pass through).
8. Clear distance between longitudinal bars in columns not less that 1.5db or 1.5 in.
9. Minimum cover of 1.5 in.
10. Summaries in Fig. 2.7 and Table 2.1, 2.2.
Table 2.1: Total areas for various numbers of reinforcing bars (inch2 )
Determine the ultimate moment capacity of example 2.1 fc = 4,000 psi; ft = 475 psi; fy =
60,000 psi; As = 2.35 in2
yt
25" 23"
2
yb
As = 2.35 in
10"
Solution:
As 2.35
ρact = = = .0102 (2.39-a)
bd (10)(23)
f 87 4 87 √
ρb = .85β1 c = (.85)(.85) = .0285 > ρact (2.39-b)
fy 87 + fy 60 87 + 60
As fy (2.35)(60)
a = = = 4.15 in (2.39-c)
.85fc b (.85)(4)(10)
a 4.15
Mn = As fy d − = (2.35)(60) 23 − = 2, 950 k.in (2.39-d)
2 2
Md = φMn = 0.9(2, 950) = 2, 660 k.in (2.39-e)
Note:
3. Alternative solution:
fy
Mn = ρact fy bd2 (1 − .59ρact ) (2.40-a)
fc
fy
= As fy d(1 − 59ρact ) (2.40-b)
fc
60
= (2.35)(60)(23)[1 − (.59) (.0102)] = 2, 950 k.in = 245 k.ft (2.40-c)
4
Md = φMn = (.9)(2, 950) = 2, 660 k.in (2.40-d)
Design a R/C beam with L = 15 ft; DL = 1.27 k/ft; LL = 2.44 k/ft; fc = 3,000 psi; fy =
40 ksi; Neglect beam own’s weight; Select ρ = 0.75ρb
Solution:
Design a R/C beam for b = 11.5 in; d = 20 in; fc = 3 ksi; fy = 40 ksi; Md = 1, 600 k.in
Solution:
d 20
Assume a = 5 = 5 = 4 in
Md (1, 600)
As = a = = 2.47 in2 (2.42)
φfy (d − 2 ) (.9)(40)(20 − 42 )
check assumption,
As fy (2.47)(40)
a=
= = 3.38 in (2.43)
(.85)fc b (.85)(3)(11.5)
Thus take a = 3.3 in.
(1, 600)
As = = 2.42 in2 (2.44-a)
(.9)(40)(20 − 3.32 )
(2.42)(40) √
⇒a = = 3.3 in (2.44-b)
(.85)(3)(11.5)
2.42
ρact = = .011 (2.44-c)
(11.5)(20)
3 87
ρb = (.85)(.85) = .037 (2.44-d)
40 87 + 40 √
ρmax = .75ρb = .0278 > ρact (2.44-e)
38 Equivalent width for uniform stress, Fig. 2.8 must satisfy the following requirements (ACI
8.10.2):
1. 1
2 (b − bw ) ≤ 8hf
39 Two possibilities:
1. Neutral axis within the flanges (c < hf ) ⇒ rectangular section of width b, Fig. 2.9.
be
hf 1111111111
0000000000
0000000000
1111111111
0000000000
1111111111
0000000000
1111111111
0000000000
1111111111
0000000000
1111111111
0000000000
1111111111
bw
h
00000000000000000
11111111111111111
11111111111111111
00000000000000000
f
h d
As
b
ε u =0.003 0.85 f’c
hf 11111111111111111
00000000000000000
00000000000000000
11111111111111111 a=β1 c
00000000000000000
11111111111111111
00000000000000000
11111111111111111 c
C=0.85f’ a
c
00000000000000000
11111111111111111
00000000000000000
11111111111111111
hd 00000000000000000
11111111111111111
d
As
εs T=As yf
bw
40
2–19
For T beams, we have a large concrete area, start by assuming that failure will occur by steel
yielding, Fig. 2.10.
41 The approach consists in decomposing As into 2 components Fig. 2.11.
2.6.1 Review
00000
11111
00000
11111 00000
11111
00000
11111 11111
00000
hf
00000
11111 00000
11111 00000
11111
00000
11111
00000
11111 00000
11111 00000
11111
00000
11111 c
00000
11111
00000
11111
00000
11111
= + 00000
11111
bw A sf A s − A sf
As (b−b w)h f bwc
Flanges:
.85fc (b−bw )hf
Asf = fy ΣF = 0
h
(2.45)
Mn1 = Asf fy (d − 2f ) ΣM = 0
Web:
s (A −A
sf y )f
a = .85fc bw ΣF = 0
(2.46)
Mn2 = (As − Asf )fy (d − 2 ) ΣM = 0
a
Total moment:
Mn = Mn1 + Mn2 (2.47)
thus,
ρb
As fy = .85fc β1 cbw + Asf fy
fc εu
As
ρ w = bw d ρw = .85 β1 +ρf (2.49)
Asf
fy εu + εy
ρf = bwd
Victor Saouma Mechanics and Design of Reinforced Concrete
Draft
2–20
Hence,
FLEXURE
ρwb = ρb + ρf (2.50)
ρw,max = .75(ρb + ρf ) (2.51)
For the following beam: As = 8 # 11 ( 12.48 in2 ); fc =3,000 psi; fy = 50,000 psi. Determine
Mn
30"
ε u=0.003 0.85 f’c
11111111111111111
00000000000000000 a= β1c
7" 00000000000000000
11111111111111111
00000000000000000
11111111111111111 C=0.85f’c ab
00000000000000000
11111111111111111 c
00000000000000000
11111111111111111
00000000000000000
11111111111111111
36" 00000000000000000
11111111111111111
d
εs T=Asfy
14"
Solution:
3. For a T section
.85fc hf (b − bw )
Asf = (2.53-a)
fy
(.85)(3)(7)(30 − 14)
= = 5.71 in2 (2.53-b)
50
Asf 5.71
ρf = = = .0113 (2.53-c)
bwd (14)(36)
Asw = As − Asw = 12.48 − 5.71 = 6.77 in2 (2.53-d)
Asw 12.48
ρw = = = .025 (2.53-e)
bw d (14)(36)
f 87
ρb = .85β1 c (2.53-f)
fy 87 + fy
3 87
= (.85)(.85) = .0275 (2.53-g)
50 87 + 50
Determine the moment capacity of the following section, assume flange dimensions to satisfy
ACI requirements; As = 6#10 = 7.59 in2 ; fc = 3 ksi; fy =60 ksi.
28"
ε u=0.003 0.85 f’c
11111111111111111
00000000000000000 a= β1c
6" 00000000000000000
11111111111111111
00000000000000000
11111111111111111 C=0.85f’c ab
00000000000000000
11111111111111111
00000000000000000
11111111111111111
c
00000000000000000
11111111111111111
26" 00000000000000000
11111111111111111
d
εs T=Asfy
10"
Solution:
(7.59)(60)
FLEXURE
given L = 24 ft; fy = 60 ksi; fc = 3 ksi; Md = 6, 400 k.in; Design a R/C T beam.
3"
20"
11"
47"
Solution:
2. Assume a = 3 in
Md 6, 400
As = a = = 6.40 in2 (2.58-a)
φfy (d − 2 ) 0.9)(60)(20 − 32 )
Victor Saouma Mechanics and Design of Reinforced Concrete
Draft
2.7 Doubly Reinforced Rectangular Beams
As fy (6.4)(60)
2–23
a =
= = 3.20 in > hf (2.58-b)
(.85)fc b (.85)(3)(47)
d 20
4. Now, this is similar to the design of a rectangular section. Assume a = 5 = 5 = 4. in
1, 830
As − Asf = = 1.88 in2 (2.60)
(.90)(60) 20 − 42
5. check
1.88)(60)
a = = 4.02 in ≈ 4.00 (2.61-a)
(.85)(3)(11)
As = 4.58 + 1.88 = 6.46 in2 (2.61-b)
6.46
ρw = = .0294 (2.61-c)
(11)(20)
4.58
ρf = = .0208 (2.61-d)
(11)(20)
3 87
ρb = (.85)(.85) = .0214 (2.61-e)
60 87 + 60
√
ρmax = .75(.0214 + .0208) = .0316 > ρw (2.61-f)
6. Note that 6.46 in2 (T beam) is close to As = 6.40 in2 if rectangular section was assumed.
2. Support stirrups
h d d−d’
= +
d
46 Approach will again be based on a strain compatibility analysis & equilibrium equation, Fig.
2.12.
47 If ρ ≤ ρmax = .75ρb we can disregard compression steel
48 As for T beams, we decompose the tension steel into two components
1. As to resist the force in the top steel (assuming both yield)
and we define
As
ρ = (2.62)
bd
I II III IV
f = fy f = fy f < fy f < fy
s s s s
f’ = f y f’ < f f’ = f f’ < f y
s s y s y s
Test 1 fs = fy ?
Assuming εs = εy , and fs = fy , we have from the strain diagram, Fig. ??
ε u =0.003
2–25
d’ εs’
A’s
h d
εs = εy
As
d
εs = εu − (εu + εy ) (2.63-a)
d
fs = Es εs (2.63-b)
εu
c = d (2.63-c)
ε u + εy
(2.63-d)
From equilibrium:
ρbdfy = ρ bdfs + .85fc β1 bc (2.64)
Combining:
fs f εu
ρb = ρ1 = ρ + .85 c β1 (2.65)
fy fy εu + εy
ρb
thus
fs
ρb = ρ1 = ρ + ρb (2.66)
fy
f
ρmax = 0.75ρb + ρ s (2.67)
fy
Note that 0.75 premultiplies only one term as in the other failure is ipso facto by yielding.
We also note the similarity with ρmax of T Beams (where 0.75 premultiplied both terms).
Test 2 fs = fy is fs = fy ?
We set εs = εy , and from the strain diagram
εu
c= d (2.68)
εu − ε y
from equilibrium
ρbdfy = ρ bdfy + .85fc β1 cb (2.69)
ε u =0.003
FLEXURE
d’ εs’ = εy
A’s
h d
εs > εy
As
combining
fc d 87
ρmin ≡ ρ2 = ρ + .85β1 (2.70)
fy d 87 − fy
which corresponds to the minimum amount of steel to ensure yielding of compression steel
at failure. Thus, if ρ < ρmin then fs < fy .
Test 3 fs < fy , is fs = fy ?
From strain diagram:
εu
c = d (2.71-a)
εu − ε y
d−c
εs = εy (2.71-b)
c − d
From equilibrium
ρbdfs = ρ bdfy + .85fc β1 bc (2.72-a)
combining
c − d f c
ρ = ρ3 = ρ + .85β1 c (2.73)
d−c fy d
a
MnI = .85fc ab d − + As fy (d − d ) (2.75)
2
ρmin ρ ρ
ρ
II I III IV
Figure 2.16: Summary of Conditions for top and Bottom Steel Yielding
Case II We have fs = fy and fs < fy (small bottom and large top reinforcement ratios, most
common case)
c − d
εs = εu (2.76-a)
c
fs = Es εs (2.76-b)
As fy = As fs + .85fc bβ1 c (2.76-c)
solve for c and fs by iteration.
Using a = β1 c
a
MnII = .85fc ab d − + As fs (d − d ) (2.77)
2
Case III fs < fy and fs = fy (large bottom and small top reinforcement ratios, rare)
d−c
ε s = εu (2.78-a)
c
fs = E s εs (2.78-b)
As fs = As fy + .85fc ab (2.78-c)
a = β1 c (2.78-d)
solve for a
a
MnIII = .85fc ab d − + As fy (d − d ) (2.79)
2
Case IV fs < fy and fs < fy (large bottom and top reinforcement ratios, rare)
c − d
εs = εu (2.80-a)
c
d−c
εs = εu (2.80-b)
c
As fs = As fs + .85fc ab (2.80-c)
a = β1 c (2.80-d)
solve for a
FLEXURE
a
MnIV = .85fc ab d − + As fs (d − d ) (2.81)
2
50 Note that in most beams of normal size and proportions, it will be found that fs < fy when
fs = fy . We nevertheless use As in order to ensure ductility, stiffness and support for the
stirrups.
Given, fc = 4, 000 psi, fy = 60,000 psi, As = 3 (1.56) = 4.68 in2 , As = 4 (1.56) = 6.24 in2 ,
determine the moment carrying capacity of the following beam.
A’s = 3 # 11 ε u =0.003 0.85 cf’ 0.85 f’
c
A’s f’s A’s f’y
3" εs’ a=β c a=β1 c
c 1
27.3" = d−d’ +
d
εs As sf (As − A’ )
s s
As yf
16"
As = 4 # 11
Solution:
1. Determine ρ:
fc 87 4 87
ρb = (.85)β1 = (.85)(.85) = .0285 (2.82-a)
fy 87 + fy 60 87 + 60
6.24
ρ = = .0143 (2.82-b)
(16)(27.3)
4.68
ρ = = .0107 (2.82-c)
(16)(27.3)
fc d εu
ρmin = ρ + .85 β1 (2.83-a)
fy d εu − εy
4 3 .003
= .0107 + (.85) (.85) = .0278 > ρ (2.83-b)
60 27.3 .003 − 29,000
60
Hence
ρ < ρmin < ρb
(2.84)
.0143 < .0278 < .0285
and thus fs = fy and fs < fy and we have case II
3. We have two equations (strain compatibility and summation of forces) and two unknowns
2–29
c and fs
c − d c−3
fs = Es εu = (29, 000)(.003) (2.85-a)
c c
c−3
= 87 (2.85-b)
c
As fy = As fs + .85fc bβ1 c (2.85-c)
(6.24)(60) = (4.68)fs + (.85)(4)(16)(.85)c (2.85-d)
374.4 = 4.68fs + 46.24c (2.85-e)
fs = −9.9c + 80.2 (2.85-f)
Note that if we were to plott those two equations,
50
25
2 3 4 5 6
-25
-50
-75
-100
We note that f s increases with c from the strain diagram, but fs decreases with c from
equilibrium. Graphically the solution is around 4.9.
4. Combining those two equations1
c2 + .7085c − 26.42 = 0 (2.86)
we obtain c = 4.80 in a = 0.85(4.8) = 4.078 in, and fs = (.003)(29, 000) 4.80−3
4.80 = 32.6 ksi
6. Check
fs
ρmax = .75ρb + ρ (2.88-a)
fy
32.6 √
= (.75)(.0285) + (.0107) =
.027 (2.88-b)
60
ρ
1
In this problem, unfortunately an iterative method diverges if we were to start with a = d5 .
Given Md = 505 k.ft, fc = 4 ksi, fy = 60 ksi, b = 12 in, h = 24.5 in, d = 21 in, and
d= 2.5 in, determine the reinforcement As and possibly As .
Solution:
1. Check if T or rectangular:
Note that if it turned out that fs < fy , then we will need to make an assumption on As (such
as As = A2s , as we will have three equations (2 of equilibrium and one of strain compatibility)
and four unknowns (As , As , fs and c).
51Considering the equilibrium of forces acting on an infinitesimal portion of a rebar, Fig. 2.17,
and defining U as the force per unit length, we have
M M +∆M
111
000
000
111
000
111
111
000 111
000
C C + dC
T 000000000000000000
111111111111111111 T+dT
Z 000000000000000000
111111111111111111
000000000000000000
111111111111111111
V V+dV
T T+dT
dx
dx
dT
U dx = dT ⇒ U = (2.92)
dx
M = T jd (2.93-a)
dM
dT = (2.93-b)
jd
u stresses on concrete
M M
u stresses on rebar
1111111111111111111111111111111111
0000000000000000000000000000000000
0000000000000000000000000000000000
1111111111111111111111111111111111
1111111111111111111111111111111111
0000000000000000000000000000000000
Bond stress u
58
Failure will initiate at points of high shear large dM
.
2–33
dx
59It frequently starts at diagonal cracks ⇒ dowel action increases the tendancy of splitting ⇒
shear and bond failures are often interrelated.
60Basedon tests with one single bar, ultimate average bond force/inch of length of bar is
Un ≈ 35 fc .
61If we have several bars in one layer spaced 6 in or less, then the ultimate bond capacity is
80% of the single bar case.
62 In terms of bond stress, Fig. 2.20
35 fc
un = (2.97)
Σ0
1111111111111111111111111111111111
0000000000000000000000000000000000
Ts = 0 Ld Ts= A yf
b
63 Putting it differently, the minimum length necessary to develop through bond a force As fy
is, Fig. ??.
A f
Ld = Ubny 0.028Ab fy
Un = un√ Σ0 ld = (2.98)
35 fc
fc
un = Σ0
U
A sf y
L
d
65
FLEXURE
If actual development length l is smaller than ld , then we must provide anchorage in order
to avoid a bond failure.
66 Note:
1. Un is independent of diameter
2. For a given fs
T = Ab fs
πd2 fs πd2b
= fs 4 b ld = (2.100-a)
Ab f s
4Un
ld = Un
ld increases with the square of db ⇒ small bar diameters require shorter development
length.
67Top bars, with more than 12 inch of concrete below them, will have a reduced bond stress
(due to rise of water during vibration). This reduction in bond results in an increase of ld by
40%
68 ACI 12.2.2 may be obtained from above but rather than use φ we increase ld by 15% for
safety.
ldb = .04 √b
A fy
#11 or smaller; and deformed wire
fc
.085 √
fy
= #14
fc (2.101)
.125 √y
f
= #18
fc
> 12 in. in all cases
Consult ACI 12.5 code for hooks geometry, and corrections to this basic equation.
69 Check ACI code for modifications related to top reinforcement, lightweight aggregate, high
strength reinforcement, excess reinforcement, and spiral confinement.
70 If not enough development length can be provided ⇒ provide hooks, Fig. 2.22 at
where
lhb = 1200 √db
fc (2.103)
ldh = λd lhb
and λd is given in the ACI code.
db
As in part (b)
Critical
section 12db
ldh
(a)
db
Critical
section 4db or 2 1/2 4db Nos. 3 through 8
in. min.
5db Nos. 9, 10, 11
ldh 6db Nos. 14 and 18
(b)
71 Ideally, the steel should be everywhere as nearly fully stressed as possible. Since the steel
force is proportional to the moment, then the steel area is nearly proportional to the moment
diagram.
72 Requirements include, Fig. 2.23:
1. At least A3s in simple beams and As
4 for continuous beams should be extended at least 6
in. into support.
2. If negative bars are cut, they must extend at least ld beyond face of support.
3. Negative bars must extend d or 12db beyond theoretical cutoff point defined by moment
diagram.
4. At least one third of top reinforcement at support must extend at least ld beyond the-
ln
oretical cutoff point of other bars, and d, 12db or 16 beyond the inflection point of the
negative moment diagram.
73 Determination of cutoff points can be rather tedious, for nearly equal spans uniformly loaded,
in which no more than about one half the tensile steel is to be cut off or bent, locations shown
in Fig. 2.24 are satisfactory (note that left support is assumed simply supported).
74 Fig. 2.25 is an illustration of the moment capacity diagram for a beam.
Theoretical
positive
moment
Face of support
Inflection point
for (+As) Moment Capacity
of bars O
of span
Theoretical
negative
Inflection point
moment for (-As)
L
Moment capacity
C
of bars M
Greatest of d, 12 d , ln/16 b
ld
Bars M ld Bars N
Bars L ld Bars O
ld d or 12 db
6" for at least
1/4 of (+AS)
(1/3 for simple spans)
L1 L1 L2 L2
4 3 3 3
0" 0" L2
L1 L2
6"
8
6" 6" 8
8
L1 L2
L1 L1 L2 L2
4 3 3 3
0" 0" L2
6" L1 L1 L2
7 4 6" 6" 4
4
L1 L2
Figure 2.24: Standard cutoff or bend points for bars in approximately equal spans with uni-
formly distributed load
A B C
5 bars
2 bars 4 bars AA
A B C
BB
Ld
Ld Mcap of 5 bars
CC
Mcap of 4 bars
Md=φMn
Ld
Mcap of 2 bars
d or 12’’
Chapter 3
SHEAR
3.1 Introduction
1 Beams are subjected to both flexural and shear stresses. Resulting principal stresses (or stress
trajectory) are shown in Fig. 3.1.
Tension trajectories
Compression trajectories
90 α
45
τ τ τ τ
σ1 σ2
τ
τ σ τ σ
α
τ
σ
τ σ τ
τ ο
45 τ σ2 σ1
2 Due to flexure, vertical flexural cracks develop from the bottom fibers.
3 As a result of the tensile principal stresses, two types of shear cracks may develop, Fig. 3.2:
Large V Large V
Small M Large M
Web shear cracks: Large V, small M. They initiate in the web & spread up & down at ≈ 45o .
6 We shall first examine the shear strength of uncracked sections, then the one of cracked
7 Q: What is the maximum shear force which can be applied before a flexural crack develop
8 Note that all shear resistance is provided by the concrete. As with flexural reinforcement,
steel is ineffective as long as the section is uncracked.
C vc τ
σ
jd +
Flexure Shear
T
9 Solution strategy:
1. Determine the flexural compressive stress fc in terms of M
2. Shear stress
3–3
Vn
vn = F2 (3.2)
bd
3. From Mohr’s circle, the tensile principal stress is
τ
vn
fc f1
σ
2
fc fc
f1 = + + vn2 (3.3)
2 2
Vn ft
= 2 1/2 (3.5)
bd
F E
F1 Ec Mn 1 c Mn 2
+ + F2
2 E ρVn d 2 Es ρVn d
s C 2
C1 C1
5. set ft = 4 fc
Vn 1
= 2 (3.6)
bd fc √ √
fc Mn C1 fc Mn
C1 ρ Vn d + ρ Vn d + C2
√
Mn fc
6. Let the variables be √n
V
&
bd fc ρVn d
7. This is how far we can go analytically. To determine the exact factors associated with
this equation, one has to undertake a series of tests.
Vn
bd f’c
3.5
2.0
1.9
Vn d
M f’
n c
Vn ρVn d
= 1.9 + 2, 500 ≤ 3.5 (3.7)
bd fc Mn fc
Vn
or if we set vc = bd , then
ρVn d
vc = 1.9 fc + 2, 500 ≤ 3.5 fc (ACI 11.3.2.1) (3.8)
Mn
Vn d
9. Note that vc is in terms of M or inverse of shear span ( M
V )
10. This equation is usually found acceptable for predicting the flexure shear cracking load
for shear span/depth ratio VMnnd of 2.5 to 6 & is found to be very conservative for lower
values
11. Increasing ρ has a beneficial effort as a larger amount of steel results in narrower & smaller
flexural tension cracks before formation of diagonal cracks ⇒ larger area of uncracked
concrete can resist the shear.
Vu Mu
12. Use of Vu & Mu instead of Vn = φ & Mn = φ
s
3–5
C
Vc
A v fv z
Va
T=As fs
Vd
Figure 3.6: Free Body Diagram of a R/C Section with a Flexural Shear Crack
where
Vc Shear resisted by uncracked section
p
n # of stirrup traversing the crack n = s
Av Area of shear reinforcement
fv Shear reinforcement stress
Vd Dowel force in steel
Va Aggregate interlock
V int
V cz
t
in
Vd
ΣV
V ay
Vs
Vext
Yield of stirups
Flexural cracking
Inclined cracking
Failure
2. Neglect Vd
3. Vext = Vn = Vc +nAv fy
unknown
4. We will assume that at failure the shear force provided
by concrete is equal to the one
which caused the diagonal crack to form ⇒ va = 1.9 fc + 2, 500ρ VMndd . Thus, Vc = va bw d
5. Finally, if we assume p = d (implying a crack at 45◦ )
d
Vn = Vc + Av fy (ACI 11.1.1) (3.10)
s
Vs
d
3–7
V
b wd
Vu
φ
10 f ’c
f ’c
6 f ’c Steel
8
f ’c
4
2 f ’c
f ’c Concrete
min. stirups
no stirups
A vfy d φ Avfy
s= Vu = (v u−φv c) b
50b w
−Vc
A v fy
φ
distance from support
s =
Figure 3.8: Summary of ACI Code Requirements for Shear
3.5 Examples
b = 12 in.; d=22 in.; wu = 8.8 k/ft; L= 20 ft.; As = 3# 11; fc = 4 ksi; fy = 40 ksi;
Design vertical stirrup
Solution:
2. At d from support Vu = 88 − 22
12 (8.8) = 71.9 k and vu = 71.9
(12)(22) = .272 ksi
√
3. vc = 2 fc = 2 4, 000 = 126 psi; φvc = (0.85)(126) = 107.1 psi
4. vc = 4 fc = 2(126) = 252 psi; φv2 c = 53.6 psi
√
5. vu − vc = 272 − 126 = 146 psi < 4 fc
psi d
SHEAR
333
Vu
272
107.1 φv c
φv c
53.6
2
x
19"
min. reinforcement no reinforcement
38.6"
6. vu − φvc = 0 ⇒ 333
(10)(12) x = 107.1 ⇒ x = 38.6 in = 3.2 ft from mid-span
φvc
7. vu − 2 =0⇒ 333
(10)(12) x = 53.6 ⇒ x = 19.3 in = 1.6 ft
9. at support
Av fy d φAv fy
s = = (3.17-a)
− Vc u − φvc )b
Vu (v
φ
(.85)(.22)(40, 000)
= (3.17-b)
(272 − 107.1)(12)
= 3.78 in (3.17-c)
(3.17-d)
15 Previous design procedure was applicable to diagonal tension cracks (where tension was
induced by shear), for those cases where we do have large pure shear, Fig. 3.9 use shear friction
concept.
16The crack for which shear-friction reinforcement is required may not have been caused by
shear. However once the crack has occurred a shear transfer mechanism must be provided, Fig.
#7 Vu
N uc
An=
φfy
weld
Nuc
A n part of A v f
close sriru
(usually #3)
Avf
assumed crack
+ shear plane
remainder of A v f
assumed crack
Vu
Vn Vn
Vn
crack
crack separation
µ A vf f y
due to slip
Vn Vn
Shear−transfer
reinforcement A fy
vf
Avf f y Avf f y
2 2
3.10. The shear friction theory is based on the assumption that a crack will occur and then
reinforcement across it will resist relative displacement along the crack.
17 If we assume separation to be sufficient⇒ steel will yield
Vn = µAvf fy (3.18)
18 If the shear reinforcement is inclined with respect to the crack, Fig. 3.11
Tsin α f
Tcos α f
assumed crack
applied shear=Vn
A vf fy
µC
C=Tsin α f
αf
T
Design reinforcement needed at the bearing region of a precast beam 14” wide & 28” deep
supported on a 4” bearing pad. Vu = 105k, horizontal force due to restraint, shrinkage, creep
is 0.3 Vu
possible crack
A vf
20
3#6
15
N uc
2#6 15
Vu N uc
4"
24" Vuc
Solution:
1. Assume all the shear Vu will be acting parallel to crack (small angle 20◦ )
2. Assume all Vu is parallel to crack ⇒ required Avf = Vu
φfy µ = 105
(0.85)(60)(1.4) = 1.47 in2
(0.3)(105)
3. As = N 2
φfy = (0.85)(60) = 0.62 in for horizontal force
ac
⇒ As = Avf + An = 1.47 + 0.62 in2 = 2.09 in2 ⇒ use 5# 6 (As = 2.20 in2 )
4. Note: ACI 11-9-3-4 Nuc > 0.2 Vu for Corbels;
compression, and (-ve) tension; Ah < As also Ah ≥ 0.50As distributed uniformly; thru
fc
3 d adjacent to As ; ρ = bd ≥ .04 fy .
2 As
Chapter 4
CONTINUOUS BEAMS
4.1 Continuity
1 R/C bldgs constructions commonly have floor slabs, beams, girders and columns continuously
placed to form a monolithic system
2
+ve
In a continuous system, load must be placed in such a way to maximize desired effect (Mmax
−ve V
Mmax max , Fig. 4.2
Max +ve M @
AB_CD_EF
A B C D E F G
Max -ve M @ B
Min -ve @ B
Max -ve @ C
Min -ve @ C
Max -ve @ D
Min -ve @ D
3 Given the moment diagram for various load cases, a designer should draw the moment
enveloppe and design for the maximum negative and positive moments (eventhough they may
not be caused by the same load case).
Draft
4–2
4 Two approaches:
1. Detailed analysis
5 Refer to CVEN3525/3535/4525
1. 2 or more spans
2. Spans are approximately equals, and the larger of adjacent ones not greater than the
shorter by more than 20%
4. LL < 3DL
5. Prismatic members
Positive Moment
End Spans
1 2
Continuous end unrestrained 11 wu Ln
1 2
Continuous end integral with support 14 wu Ln
1 2
Interior spans 16 wu Ln
Negative Moment
Negative moment at exterior face of first of first interior support
1 2
Two spans 9 wu Ln
1 2
> Two spans 10 wu Ln
1 2
Negative moment at other faces of interior support 11 wu Ln
...................................... ......
Shear
Shear in end member at face of first interior support 1.15 wu2Ln
wu Ln
Shear at face of all other supports 2
C
L column
C
L column
CL span
VaL
111
000 VaL
000
111
000
111 3
6
V
000
111
000
111
000
111 C
VaL VaL
L beam 2 VaL 3
aL 6
2
Column width aL
L
2
Moment curve based on prismatic member
aL
1111111111111111111111111
0000000000000000000000000
0000000000000000000000000
1111111111111111111111111
VaL
6
2
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
Adjusted Moment Curve
0000000000000000000000000 L
1111111111111111111111111 C beam
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000 CL beam
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
0000000000000000000000000
1111111111111111111111111
9 Negative moments should be the one at the face of the columns which is, Fig. 4.4
Vb
Md−ve ≈ Mmax
−ve
− (4.1)
3
M
4–5
Mp X
Curvature
Φy Φu
12 The beam has an elastic plastic moment curvature relation, Fig. 4.6
13 |M −ve | > |M +ve | as w , M −ve → Mp first ⇒
wL2 12Mp
= Mp ⇒ w =
12 L2
14 Thus we will have a plastic hinge at the support however this is not synonymous with collapse.
15Collapse or failure occurs when we have a mechanism or 3 adjacent hinges (plastic or other-
wise). This can be easily determined from statics, Fig. 4.7
M
p
M p
M p
wu L2
2Mp = 8
16Mp
wu = L2
16 Thus capacity was increased 33% after first plastic hinge occurred.
17This is accompanied by large rotation of the plastic hinges at the supports, and when com-
pared with the linear elastic solution M −ve and M +ve
18 The section must be designed to accomodate this rotation.
4.4.2 Concrete
19Concrete is brittle hence by itself no appreciable plastic deformation can occur, however in
R/C, Fig. 4.8
20 If certain rotation capacity exists (i.e., if ρ − ρ is low) M is controlled by yielding of the steel
while the concrete strain is still low compared to 0.003 ⇒ reserve rotation capacity θu − θy is
then available for a redistribution of moment to occur before ε → 0.003
ε ce
CONTINUOUS BEAMS
ε ce
fc fc
kd c
d−kd d−c
Asf y Asf y
ε s= ε y ε s> ε y
.003
M u
Steel yielding
εc
φ
M y
M cr
First crack
21M −ve moment at support of continuous flexural members calculated by elastic theory can
be decreased by no more than
ρ − ρ
∆M = 20(1 − )% ACI 8.4.1 (4.2)
ρb
where ρb = 0.85β1 ffyc ( 87+f
87
y
) provided that
2. ρ or ρ − ρ < 0.5ρb
Determine the moment redistribution for the following singly reinforced beam with ρ = 0.5ρb
2 2
WL WL
24 20
+ +
2 2
2 2 −
WL − − WL 0.9 WL − 0.9 W L
12 12 12 12
Solution:
4–7
4.5 Buildings
Vertical loads: DL and LL. This is typically done for a floor, through a grid analysis. No
need to model the entire structure. We can use
Lateral laod: WL, EL. This requires the analysis of a 2D or 3D frame. Two approaches:
1. Use ACI approximate equations for the design of the slab. Then, there is no need to worry
about optimal placement of load to maximize positive or negative moments, or moment
redistribution.
2. Once the slab is designed, use exact method for beams, girders. Reduce negative moments.
5. Can use approximate or “exact” method of analysis for frames. Tabulate results.
CONTINUOUS BEAMS
6. Add maximum positive and negative moments due to vertical and lateral loads.
7. Design accordingly.
h h h b
hf
DL w0 LL w0 PW PW WL w0 PW w0 WL
wu wu wu wu
M V M V
M V R M V R
L Span
hf Slab thickness N
h Beam/girder depth
M Flexure
V
R
Shear
Reation
Col
PW Partition wall W E
WL Wind load
W0
Wa
Self weight
Total factored load
Fou
Col Column
Fou Foundation S
R/C Bldg Design
Chapter 5
SERVICEABILITY
1 So far we have focused on the ultimate structural behaviour (failure), Vu & Mu , i.e the strength
of a member.
2 It is important to also control the behaviour of structural elements under service load (unfac-
tored)
1. Cracking
2. Deflection
3 As σy , εy ⇒ larger crack width is associated with large fy . This is why the ACI code
1. Appearance
2. Corrosion of steel
4. Effect on deflection
2. Steel stress
3. Concrete cover
Draft
5–2
7 Based on purely experimental research, the following emperical relation was determined, Fig.
5.1:
w = .076βfs 3 dc A Gergely & Lutz Eq. (5.1)
where
w width in 1/1,000 in
fs Steel service stress ksi (if not computed can be assumed as 0.6 fy )
dc Thickness of concrete cover measured from tension face to center of bar
closest to this face, in.
h2
β h1
A Area of concrete surrounding one bar = Total effective tensile area in2
# of bars
Neutral Axis
h
111
000 h1 2
000
111
000
111 Steel Centroid
2y
000
111
y 000
111
d
c
w
8 ACI
w
z= = fs 3 dc A (ACI 10.6.4) (5.2)
.076β
and assumes β = h2
h1 = 1.2 ⇒ w = .091z
Interior beams z ≤ 175 (w = .016 in)
Exterior beams z ≤ 145 (w = .013 in)
2. Only deformed bars can be used
4. fy < 80ksi
20"
11.5"
Solution:
√
1. w = .076βfs 3 dc A
√
2. Ec = 57 3, 000 = 3, 120 ksi
29×103
3. n = 3,120 = 9.29
b(kd)2
4. 2 − nAs (d − kd) = 0 ⇒ k = .393 ⇒ j = 1 − k
3 = .869 ⇒ kd = 7.85 in
2
5. fs = AM
s jd
⇒ fs = (1.27+2.44)(15) (12)
8(3.14)(.869)(20) = 22.9 ksi
Note that ACI allows 0.6fy = (0.6)(40) = 24 ksi conservative
22.5−7.85 14.65
6. β = 20−7.85 = 12.15 = 1.206 (note ACI stipulates 1.2)
(2.5)(2)(11.5)
7. A = 4 = 14.38 in2
1
8. w = (.076)(1.206)(22.9) 3 (2.5)(14.38) 1,000 = .00696 in .
√
9. or z = fs3 dc A = (22.9) 3 (2.5)(14.38) = 75.64
5.2 Deflections
SERVICEABILITY
1. Visually unacceptable
5. Machine misalignment
6. Vibration
18 f (w, l) and E are known, but how do we determine I?, Fig. 5.2
Ε cΙ ut Ε cΙ e 1 Ε cΙ e 2 Ε cΙ cr
Μ2
Μ1
Μ cr
Α B Α B Α B Α B Α B ∆ ∆
1 2
' (
Mcr 3 Mcr 3
Ieff = Ig + 1 − Icr (ACI 9.5.2.3) (5.3)
Ma Ma
where
Ieff ≤ Ig
Mcr = fr ygb
I
fr = 7.5 fc
and Ma is the maximum (service) moment at stage in which deflection is computed
21 For continuous beams average
22 For beams with one end continuous Ieff = 0.85Im + 15(Icon ) where Im , Ie are the moment of
δt
δ inst.
25 Creep coefficient:
εf
Cc = εi
σ σ Ec
Ect = ε = εi (1+Cc ) = 1+Cc
2. As concrete undergoes creep, the N.A. moves down ⇒ larger area of concrete is under
compression but since C = T ⇒ stress in concrete is slightly reduced
fci
b εi εt
fct
Cracked
elastic φi
neutral axis d
φt
kd
As A s fs
εs
3. But since C is now lower and we still satisfy Mext = Mint both stresses in steel & concrete
must increase with time
δt = δi × λ (5.4)
where
ξ
λ = 1+50ρ
As
ρ = bd
and
Time (months) 3 6 12 ≥ 60
ξ 1.0 1.2 1.4 2.0
A B C
LL short
DL sustained
1111
0000 1111
0000
0000
1111 1111
0000
A → δi,sust
B → δi,sust + δt,sust
C → δsust + δi,short
and
L
Flat roof not supporting nonstructural elements likely to be damaged δi,sh < 180
L
Floors not supporting nonstructural elements likely to be damaged δi,sh < 360
L
Roofs or floors supporting nonstructural elements likely to be damaged δt,sust + δi,sh < 480
L
Floors not supporting nonstructural elements not likely to be damaged δt,sus + δi,sh < 240
b = 11.5 in.; h = 22.5 in,; d = 20 in.; As = 4 # 8; fc = 3,000 psi; fy = 40 ksi; DL = 1.27
k/ft; LL = 2.44 k/ft; L = 15 ft.
2. Find the creep portion of the sustained load deflection & immediate live load deflections
Solution:
2. Moment of inertias:
3
3
Ieff = Mcr
Ma Ig + 1 − Mcr
Ma Ict
bh3 (11.5)(22.5)3
Ig = 12 = 12 = 10, 916 in4
11.5"
7.85"
20"
12.15"
b(kd)2
− nAs (d − kd) = 0 ⇒ k = .393 ⇒ kd = 7.85 in
2
(11.5)(7.85)3 2
Ict = + (11.5)(7.85) 7.85 + (9.29) (3.14)(12.152 ) = 6, 130 in4
12 2
√ n As
fr = 7.5 3, 000 = 410.8 psi
fI
Mcr = rybg
(410.8)(10,916)
= 11.25 = 33.2 k.ft = 399 k.in
7. Deflections √
E = 57 3, 000 = 3, 120 ksi
5 wL4
δ = 384 EI
5 (1.27+2.44)[(15)(12)]4
δi, short + sust = 384 (3,120)(6,209) = .218 in
4
5 (1.27)[(15)(12)]
δi, sust = 384 (3,120)(9,993) = .046 in
δi = .218 − .046 = .172 in
8. δcreep = λδi, sust
2.
λ= = 2. ⇒ δcreep = (2)(.046) = .092 in
1+0
Chapter 6
APPROXIMATE FRAME
ANALYSIS
1 Despite the widespread availability of computers, approximate methods of analysis are justi-
fied by
1. Inherent assumption made regarding the validity of a linear elastic analysis vis a vis of
an ultimate failure design.
6 The girders at each floor are assumed to be continuous beams, and columns are assumed to
(a) One tenth the span from both ends of each girder.
(b) Mid-height of the columns
4. Unbalanced end moments from the girders at each joint is distributed to the columns
above and below the floor.
Draft
6–2
8
APPROXIMATE FRAME ANALYSIS
Based on the first assumption, all beams are statically determinate and have a span, Ls
equal to 0.8 the original length of the girder, L. (Note that for a rigidly connected member, the
inflection point is at 0.211 L, and at the support for a simply supported beam; hence, depending
on the nature of the connection one could consider those values as upper and lower bounds for
the approximate location of the hinge).
9 End forces are given by
Maximum positive moment at the center of each beam is, Fig. 6.1
w
rgt
lft M
M
rgt
V
lft
V
0.1L 0.1L
0.8L
L
111
000
000
0000
1111
111 0000
1111
1
0
0
1 11
00
00
11
0
1 00
11
0
1 00
11
0
1 00
11
Figure 6.1: Approximate Analysis of Frames Subjected to Vertical Loads; Girder Moments
1 1
M + = wL2s = w (0.8)2 L2 = 0.08wL2 (6.1)
8 8
Maximum negative moment at each end of the girder is given by, Fig. 6.1
w w
M lef t = M rgt = − (0.1L)2 − (0.8L)(0.1L) = −0.045wL2 (6.2)
2 2
Girder Shear are obtained from the free body diagram, Fig. 6.2
wL wL
V lf t = V rgt = − (6.3)
2 2
Column axial force is obtained by summing all the girder shears to the axial force transmit-
ted by the column above it. Fig. 6.2
rgt
P dwn = P up + Vi−1 − Vilf t (6.4)
above
P
rgt lft
V i−1 Vi
below
P
Figure 6.2: Approximate Analysis of Frames Subjected to Vertical Loads; Column Axial Forces
h/2
h/2
above
M col
lft lft rgt
M rgt
Mi−1 Mi M
i−1
i
h/2
Figure 6.3: Approximate Analysis of Frames Subjected to Vertical Loads; Column Moments
Column Moment are obtained by considering the free body diagram of columns Fig. 6.3
rgt
M top = Mabove
bot
− Mi−1 + Milf t M bot = −top (6.5)
Column Shear Points of inflection are at mid-height, with possible exception when the columns
on the first floor are hinged at the base, Fig. 6.3
M top
V = h
(6.6)
2
Girder axial forces are assumed to be negligible eventhough the unbalanced column shears
above and below a floor will be resisted by girders at the floor.
Low rise buidlings, where the height is at least samller than the hrizontal dimension, the
deflected shape is characterized by shear deformations.
High rise buildings, where the height is several times greater than its least horizontal di-
mension, the deflected shape is dominated by overall flexural deformation.
11Low rise buildings under lateral loads, have predominantly shear deformations. Thus, the
approximate analysis of this type of structure is based on
2. Total horizontal shear at the mid-height of all columns at any floor level will be dis-
tributed among these columns so that each of the two exterior columns carry half as
much horizontal shear as each interior columns of the frame.
H/2 H H H/2
Figure 6.4: Approximate Analysis of Frames Subjected to Lateral Loads; Column Shear
Column Shear is obtained by passing a horizontal section through the mid-height of the
columns at each floor and summing the lateral forces above it, then Fig. 6.4
ext F lateral
V = V int = 2V ext (6.7)
2No. of bays
Column Moments at the end of each column is equal to the shear at the column times half
the height of the corresponding column, Fig. 6.4
h
M top = V M bot = −M top (6.8)
2
Girder Moments is obtained from the columns connected to the girder, Fig. 6.5
h/2
h/2
above
M col
lft rgt lft rgt
M i−1 M i−1 Mi Mi
rgt rgt
lft
Vi−1 V Vlft Vi
i−1 i
below
M col
Li−1/2 Li−1/2 Li /2 Li /2
h/2
h/2
Figure 6.5: Approximate Analysis of Frames Subjected to Lateral Loads; Girder Moment
Milf t = Mcol
above
− Mcol
below rgt
+ Mi−1 Mirgt = −Milf t (6.9)
Girder Shears Since there is an inflection point at the center of the girder, the girder shear
is obtained by considering the sum of moments about that point, Fig. 6.5
2M
V lf t = − V rgt = V lf t (6.10)
L
Column Axial Forces are obtained by summing girder shears and the axial force from the
column above, Fig. ??
above
P
rgt lft
V i−1 Vi
below
P
Figure 6.6: Approximate Analysis of Frames Subjected to Lateral Loads; Column Axial Force
Example 6-1: Approximate Analysis of a Frame subjected to Vertical and Horizontal Loads
Draw the shear, and moment diagram for the following frame. Solution:
Vertical Loads
0.25 k/ft
6–7
15 k
5 12 6 0.5 k/ft13 7 14 8
14
30 k
9 10 11
1 2 3 4 16
11
00 11
00 11
00 11
00
20’ 30’ 24’
M5top = lf t
+M12 =− 4.5 k.ft
M5bot = −M5top = 4.5 k.ft
M6top = rgt
−M12 lf t
+ M13 = −(−4.5) + (−10.1) =− 5.6 k.ft
top
M6bot = −M6 = 5.6 k.ft
M7top = rgt
−M13 lf t
+ M14 = −(−10.1) + (−6.5) =− 3.6 k.ft
M7bot = −M7top = 3.6 k.ft
M8top = rgt
−M14 = −(−6.5) = 6.5 k.ft
M8bot = −M8top =− 6.5 k.ft
7. Column Shears
M5top −4.5
V5 = H5 = 14 = − 0.64 k
2 2
M6top −5.6
V6 = H6 = 14 = − 0.80 k
2 2
M7top 3.6
V7 = H7 = 14 = 0.52 k
2 2
M8top 6.5
V8 = H8 = 14 = 0.93 k
2 2
M1top −4.5
V1 = H1 = 16 = − 0.56 k
2 2
M2top −5.6
V2 = H2 = 16 = − 0.70 k
2 2
M3top 3.6
V3 = H3 = 16 = 0.46 k
2 2
M4top 6.5
V4 = H4 = 16 = 0.81 k
2 2
0.25K/ft
5 12 6 13 7 14 8
0.50K/ft 14’
9 10 11
1 2 3 4 16’
-2.5K -3.75K
K
-3.0K
+5.0 K +7.5 +6.0 K
-5.0K -6.0K
-7.5K
1. Column Shears
15
V5 = (2)(3) = 2.5 k
V6 = 2(V5 ) = (2)(2.5) = 5k
V7 = 2(V5 ) = (2)(2.5) = 5k
V8 = V5 = 2.5 k
15+30
V1 = (2)(3) = 7.5 k
V2 = 2(V1 ) = (2)(7.5) = 15 k
V3 = 2(V1 ) = (2)(2.5) = 15 k
V4 = V1 = 7.5 k
2. Top Column Moments
(2.5)(14)
M5top = V12H5 = 2 = 17.5 k.ft
M5bot = −M5top =− 17.5 k.ft
(5)(14)
M6top = V62H6 = 2 = 35.0 k.ft
M6bot = −M6top =− 35.0 k.ft
V up H (5)(14)
M7top = 7 2 7 = 2 = 35.0 k.ft
M7bot = −M7top = − 35.0 k.ft
V up H (2.5)(14)
M8top = 8 2 8 = 2 = 17.5 k.ft
M8bot = −M8top = − 17.5 k.ft
3. Bottom Column Moments
V dwn H (7.5)(16)
M1top = 1 2 1 = 2 = 60 k.ft
M1bot = −M1top = − 60 k.ft
V dwn H (15)(16)
M2top = 2 2 2 = 2 = 120 k.ft
M2bot = −M2top = − 120 k.ft
V dwn H (15)(16)
M3top = 3 2 3 = 2 = 120 k.ft
M3bot = −M3top = − 120 k.ft
V dwn H (7.5)(16)
M4top = 4 2 4 = 2 = 60 k.ft
M4bot = −M4top = − 60 k.ft
4. Top Girder Moments
lf t
M12 = M5top = 17.5 k.ft
rgt lf t
M12 = −M12 =− 17.5 k.ft
lf t rgt
M13 = M12 + M6top = −17.5 + 35 = 17.5 k.ft
rgt lf t
M13 = −M13 =− 17.5 k.ft
lf t rgt
M14 = M13 + M7top = −17.5 + 35 = 17.5 k.ft
rgt lf t
M14 = −M14 =− 17.5 k.ft
A B C D E F G H I J K L M N O P Q
1
2 L1 L2 L3
3 Height Span 20 30 24
4 14 Load 0.25 0.25 0.25
5 16 Load 0.5 0.5 0.5
6 MOMENTS
7 Bay 1 Bay 2 Bay 3
8 Col Beam Column Beam Column Beam Col
9 Lft Cnt Rgt Lft Cnr Rgt Lft Cnt Rgt
AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAA AAAA
AAAAAAAAAAAA
AAAA AAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAA
10 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA -4.5 8.0 -4.5 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA -10.1 18.0 -10.1AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA A -6.5
AAAAA 11.5 -6.5 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA AA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA
11 -4.5 AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
-5.6 AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA 3.6 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
6.5
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA AA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA
12 4.5 AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAA
A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA
5.6
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAA
AAA
AAAAAAA
AAA
AAAA
-3.6 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
-6.5
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAA AAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAA AAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAA AAAA -20.3 36.0 -20.3AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAA AAAAAAAA
13 AAAAAAAA
AAAAAA -9.0 16.0 -9.0 AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA A -13.0 23.0 -13.0 AAAA
AAAAA AAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
A
AAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
14 -4.5 AAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA
AA -5.6 AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA
AAA
AAA
3.6 AAAA
AAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
6.5
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AA
AAAAAA AAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
15 4.5 AAAA AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
5.6 AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAA
AAAAAAA
AAA
-3.6 AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
-6.5
16 SHEAR
17 Bay 1 Bay 2 Bay 3
18 Col Beam Column Beam Column Beam Col
19 Lft Rgt Lft Rgt Lft Rgt
AAAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA
AAAAAAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA A 2.50AAAA AAAAAAAA
AAAA
AAAA -2.50 AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA 3.75 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAAAAAA
AAAAAAAAAAAA -3.00 AAAAAAAA
AAAA
20 AAAAAAAA
AAAA
AAAAAAAAA
AAAA
AAAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA
AAAA AAAA AAAA -3.75AAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAA 3.00 AAAA
A AAAAAAAA AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA A AAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAA
AAAA AAAA
AAAA AAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AA AAAA AAAA AAAAAAAA AAAAAAAA AAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
21 -0.64 AAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AA
AAAAAA -0.80 AAAA
AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA 0.52 AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA 0.93
AAAAAAAAAAAAAAAAAAAA
A AAAAAAAA
AAAAAAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAAAAA
AAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA
AAAAAAAA
AAAA
A AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA
AAAAAAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA A 5.00AAAA AAAAAAAA
AAAA
AAAA -5.00 AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA 7.50 AAAA AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAAAAAA
AAAAAAAAAAAA -6.00 AAAAAAAA
AAAA
22 AAAAAAAA
AAAA
AAAAAAAAA
AAAA
AAAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA
AAAA AAAAAAAA AAAA -7.50AAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAA 6.00 AAAA
A AAAAAAAA AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA A AAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAA
AAAA AAAA
AAAA AAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AA AAAA AAAAAAAAAAAAAAAA AAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
23 -0.56 AAAA AAAA AAAAAAAA AAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AA -0.70 AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA 0.46 AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA 0.81
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA AAAA
AAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
24 AXIAL FORCE
25 Bay 1 Bay 2 Bay 3
26 Col
AAAAAAAAAAAAAAAAA
Beam Column
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
Beam AAAAAAAA
Column
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
A
Beam Col
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
27 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAA
AAAA
A
AAAAAAAAAAAAAAAAAAAA
0.00 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAA
AAAA
AAAAAAAA 0.00 AAAAAAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAAAAAA
AAAA AAAAAAAA
AAAA AAAAA
AAAAA
A 0.00 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAA
AAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA AA AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA
28 2.50 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAA
A
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AA
AAAAAA
AA
6.25
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAAAAAA
AAAAAAAA
6.75
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA A
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
3.00
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA A AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAA
29 AAAAAAAA
AAAAAAAA
AAAAAAAAA
AAAA
A 0.00 AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA
AAAA
AAAAAAAA 0.00 AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A
A 0.00 AAAAAAAA AAAA
AAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA A
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
A AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA
AA AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
30 7.50 AAAA AAAA AAAAAAAA AAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AA 18.75 AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA 20.25 AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
9.00
A B C D E F G H I J K L M N O P Q
Draft
Victor Saouma
2 L1 L2 L3
3 Height Span 20 30 24
4 14 Load 0.25 0.25 0.25
5 16 Load 0.5 0.5 0.5
6.2 Horizontal Loads
6 MOMENTS
7 Bay 1 Bay 2 Bay 3
8 Col Beam Column Beam Column Beam Col
9 AAAAAAAA AAAAA
Lft Cnt Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAALft Cnr Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Lft Cnt Rgt AAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA
AAAAAAAAAAA
AAAA AAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAA AAA
AAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAA
AAAAAAAAAAAA AAAAAAAA
AAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA
10 AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA =-0.045*D4*D3^2 =0.08*D4*D3*D3 =+D10 AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAA =-0.045*I4*I3^2 =0.08*I4*I3*I3 =+I10 =-0.045*N4*N3^2 =0.08*N4*N3*N3 =N10 AAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAA AAAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAA
AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA AAAAA AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
11 =+D10 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =-F10+I10 =-K10+N10 =-P10
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAA AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAA
12 =-C11 AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAA
=-G11 AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAA =-L11
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAA=-Q11
AAAAAAAAAAAA
AAAAA
AAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA AAAA
AAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
13 AAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAA
AAAA =-0.045*D5*D3^2 =0.08*D5*D3*D3 =+D13 AAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA AAAA =-0.045*I5*I3^2 =0.08*I5*I3*I3 =+I13
AAAAAAA
AAA
AAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA AAAA =-0.045*N5*N3^2 =0.08*N5*N3*N3 =+N13
AAAAAAA
AAA
AAA AAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAA
AAAAAAAA
AAAA AAAA
AAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA A AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
14 =+D13+C12 =-F13+I13+G12 =-K13+N13+L12 AAAA =-P13+Q12
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAA AAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
15 =-C14 AAAA
AAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAA =-G14
AAAA
AAAAAAAA
AAAA
AAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAA
=-L14 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =-Q14
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
16 SHEAR
17 Bay 1 Bay 2 Bay 3
18 Col Beam Column Beam Column Beam Col
19 Lft Rgt Lft Rgt Lft Rgt
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAA
AAAAAAA AAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA AAAAAAAA
AAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAA
20 AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAA =+D3*D4/2
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAA=-D20 AAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA=+I3*I4/2 AAAAAAAAAAAAAAAAAAAAAAA=-I20 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =+N3*N4/2
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAA =-N20 AAAA
AAAAAAAA
AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
AAAAAAAA AAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
21 =2*C11/A4 AAAAAAAA
AAAA
AAAA AAAA
AAAAAAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA
AAAAAAAA
AAAA
AAAA AAAA
AAAAAAAA
AAAA =2*G11/A4
AAAA
AAAA
AAAAAAAA
AAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA
AAAAAAAA
AAAA
AAAA
AAAAAAAA
AAAAAAAA A =2*L11/A4
A
AAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA=2*Q11/A4
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA
AAAA
22 AAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA =+D3*D5/2 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA =-D22 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA =+I3*I5/2 AAAAAAAAAAAAAAAAAAAAAAA
AAA =-I22 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =+N3*N5/2 AAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AA
AAAAAAAA
AAAA
=-N22
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A AAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAA
23 =2*C14/A5 AAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA =2*G14/A5 AAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA A =2*L14/A5 AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAA
=2*Q14/A5
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
24 AXIAL FORCE
25 Bay 1 Bay 2 Bay 3
26 Col Beam Column Beam Column Beam Col
AAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA AAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAA
AAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAA AAAAAAAA
AAAAAAAA AAAAAAAA AAAA
AAAAAAAA
27 AAAA AAAA
AAAAAAAA
AAAA AAAA AAAA AAAA AAAA
AAAAAA0 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA 0
AAAAAAA
AAA
AAAA AAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAA AAA
0
AAA AAAA AAAA AAAA AAAA
AAAAAAAA
AAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAA
28 =+D20
AAAA
=-F20+I20
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =-K20+N20
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA =-P20
AAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAA AAAAAAAA
AAAA AAAAAAAA
AAAA AAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAA
AAAAAAA AAAAAAAA
AAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
29 AAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA 0 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA
0 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA 0 AAAAAAAAAAAAAAAA
AAAA
AAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAA
AAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAA
AAAAAAA AAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA AAAAAAA
AAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAA
A
AAAAAAAAAAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAA
AAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAA AAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
30 =+C28+D22 AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA =+G28-F22+I22 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =+L28-K22+N22 AAAAAAAAAAAAAAAAAAAAA =+Q28-P22
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAA AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
15K 14
5 12 6 13 7 8
14’
30K 9 10 11
1 2 3 4 16’
K
-17.5’K -35’K -35’K -17.5’K
+60’ +120’K +120’K +60’K
2M lf t
lf t
V12 = − L1212
= − (2)(17.5)
20 = −1.75 k
rgt lf t
V12 = +V12 = −1.75 k
2M lf t
lf t
V13 = − L1313
= − (2)(17.5)
30 = −1.17 k
rgt lf t
V13 = +V13 = −1.17 k
2M lf t
lf t
V14 = − L14
14
= − (2)(17.5)
24 = −1.46 k
rgt lf t
V14 = +V14 = −1.46 k
Design Parameters On the basis of the two approximate analyses, vertical and lateral load,
we now seek the design parameters for the frame, Table 6.2.
A B C D E F G H I J K L M N O P Q R S
1 PORTAL METHOD
2 # of Bays 3 L1 L2 L3
3 20 30 24
4 MOMENTS
5 # of Storeys 2 Bay 1 Bay 2 Bay 3
6 Force Shear Col Beam Column Beam Column Beam Col
7 H Lat. Tot Ext Int AAAAAAAAAAAAAAAAA
Lft Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Lft Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Lft Rgt AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
8 AAAAAAAA
AAAAAAAA
AAAA
AAAA
AAAAAAAA
AAAAA
AAAA
AAAAAAAA A 17.5 -17.5 AAAA
A
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAA
AAAAAAA
AAAAAAA
17.5 -17.5 AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
17.5 -17.5AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAA
AAAAAAAA
A
A
AAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAA AAAA AAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAA AAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAA
AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA
9 H1 14 15 15 2.5 5 17.5 AAAA AAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
35.0 AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA 35.0 AAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA 17.5
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA
10 -17.5 AAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA -35.0 AAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
-35.0 AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAA -17.5
AAAAAAAAAAAAAAAAAAAA
A AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA AAA AAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A
11 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAA
AAAA
A 77.5 -77.5 AAAA AAAAAAAA
AAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAA
AAAA AAAA
AAA 77.5 -77.5 AAAAAAAA
AAA
AAAAAAA AAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAA 77.5 -77.5AAAAAAAA
AAAA
AAAAAAAA AAAAAAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAA
AAAA
A
AAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA
12 H2 16 30 45 7.5 15 60.0 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
120.0 AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA 120.0 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA 60.0
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAA
AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA
13 -60.0 AAAA AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAA
-120.0 AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAA
-120.0 AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAA
-60.0
14 SHEAR
15 Bay 1 Bay 2 Bay 3
16 Col Beam Column Beam Column Beam Col
17 Lft Rgt Lft Rgt Lft Rgt
AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA A -1.75 -1.75 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAA
18 AAAAA AAA -1.17 -1.17 AAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA -1.46 -1.46AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAA AAAA AAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAA
AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA
19 2.50 AAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA 5.00 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAA 5.00 AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA 2.50
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA
20 2.50 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA 5.00 AAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAA 5.00 AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA 2.50
AAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAA
A AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA A AAA AAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA A -7.75 -7.75 AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAA
21 AAAAA AAA -5.17 -5.17 AAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA -6.46 -6.46AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA AAAAAA
AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA A
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA A
AAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAA AAAA AAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAA AAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAA AAAAA
AAAA AAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAAAAAAAAAAAAAA
22 7.50 AAAA AAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
15.00 AAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA AAAAAAAA
15.00 AAAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
7.50
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAA
AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAA
AAAAAAAAAAAAAAAA
23 7.50 AAAA AAAAAAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
15.00 AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAA AAAAAAAA
AAAAAAAAAAAAAAAA
AAAA
15.00 AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
7.50
24 AXIAL FORCE
25 Bay 1 Bay 2 Bay 3
26 Col Beam Column Beam Column Beam Col
AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
27 AAAAAA 0.00 AAA
AAAAAAA 0.00 AAAA
AAAAAAAA 0.00 AAAAAAAAAAAA
AAAAAAAA
AAAAAA
AAAAAAAA AAAAAAAA
AAAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA AAAAAAAA
AAAAA
AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
28 1.75 AAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAA
A
AAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
-0.58
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA 0.29
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
-1.46
AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA A
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAAAAAA
29 AAAAAA 0.00 AAA
AAAAAAA 0.00 AAAA
AAAAAAAA 0.00 AAAAAAAAAAAA
AAAAAAAA
AAAAAA
AAAAAAAA AAAAAAAA
AAAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA AAAAAAAA
AAAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAAAAAA AAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA
30 9.50 AAAA AAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
-3.17 AAAA
AAAAAAAA
AAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA 1.58 AAAAAAAA
AAAAAAAA
AAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
AAAAAAAA
AAAA
-7.92
A
A
A
B
A
A
C
A
A
D
A
A
E
A
A
F
A
A
G
A
A
H
A
A
I
PORTAL.XLS
A
A
J
A
A
K
A
A
L
AA
AA
M
A
A
N
A
A
O
A
A
P
A
A
Q
6–17
A
A
R
A
A
Victor E. Saouma
S
1 PORTAL METHOD A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A AA
AA A
A A
A A
A A
A A
A A
A
A A A A A A A A A A A AA A A A A A A
A A
AAAAAAAAAAAAAA A
AAAAAAAAAAAAAAAAAAAAA A
A AAAAAAAAAAAAAAAA
A3 A AL1 A A AAAAAAAA A A
A AAAAAAAAAAAAAAAAAAAAAAA
AA AA A A A A
2 AAAA
# ofAAAA
Bays
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAA
AAAAAAAAA
AAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAA AAAAAAAA
AAAAA AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAAAAAA
A AAAA AAAAAAAA
AAAA
A AAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAA L2 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAA
AA L3 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAA A A A A A A A AAAA
AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAA
3 A
A A
A A
A A
A A
A A20
A A
A A
A AA30
AA A
A A
A A 24
A A
A
A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A AA
AA A
A A
A A
A A
A A
A A
A
4 A
A A
A A
A A
A A
A A
A A
A MOMENTS A
A A
A A
A A
A AA
AA A
A A
A A
A A
A A
A A
A
A
A A
A A
A A
A A
A
AAAAAAAAAAA A
A A
A A
A AA
AA A
A A
A A A A
5 # of Storeys A A A A A2 Bay 1 A A A Bay 2 AA A A Bay 3 AA A
A
A
A
A A A A A AAAAAAAAAAA A A A AA A A A A A
A A A A A
6 Force AA Shear A
A Col Beam A
A Column Beam A
A Column Beam A
A Col
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAA
7 H Lat. AAA Tot Ext AInt
A
A AAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA
Lft A Rgt
A
A AAAA AAAA AAAAAAAAAAAA AAAAAAA
Lft A Rgt
A
A AAAAAAAAAAAAAAAAAAAAAAAAAAA
Lft A Rgt
A
A AAAAAAAAAAAAAA
A
A A
A
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAA AAAA=+H9 AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAA AAAAAAA =+N8+O9
AAAAAAAAAAAAAA
AAAAAAAA AAAAAA
8 A A AAAAAAAA =-I8 =+J8+K9 =-M8 =-Q8
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA
AAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA AAAA
AAAAAA AAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
AA
A
AAAAA A
A=2*E9
AAAA
AAAAAAAAAAAAAAAA=+F9*B9/2
AAAAAAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAA
AA =+K9
AAA
AAAAAAAAAAAAAAAAAAAAAAA=+H9
AAAAAAAA
H1
9 AAAA 14 AAAA15 =+C9 =+D9/(2*$F$2) AAAAAAAAAAAAAAAAA =+E9*B9/2
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAAAAAAA A AAAAAAAAAAAAAAA
AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A AAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAA
A AAAAAAAAAAAAAAAAA AAAA AA AAA
10 A A =-H9 AAAAAAAA AAAAAAAAAAAA=-K9 AAAA AAAA AAAAAAAA AAAA AAAAAA =+K10 AAAAAAAA AAAAAAAAAAAAAAAAAAA=+H10
A A AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
A
A A
A
AAAAAAAAAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAA
AAAA
AAAA
AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAA
AAAAAAAAAAAA
AAAAAAAAAAAAAA
AA
11 A
A A
A
AAAAAAAAAAAAAAAAAAAA=+H12-H10 =-I11 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+K12-K10+J11 =-M11 AAAAAAAAAAAAAAAAAAAAAAAAAAA =+O12-O10+N11 =-Q11 AAAAAAAAAAAAAA
AAAA AAAAAAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAA
AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
A
A A
A
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA=+F12*B12/2 AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA=+H12
H2 16 30 A =SUM($C$9:C12) A=+D12/(2*$F$2)
12 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A=2*E12
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =+E12*B12/2 AAAAAAAAAAAAAAAA AA =+K12
AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA AAAAAAAAAAAAAAAAAAAAAAAA
A A AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAA
13 A
A A
A =-H12 AAAAAAAAAAAAAAAAAAAA=-K12
AAAA AAAAAAAAAAAA AAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA =+K13 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+H13
AAAA AAAAAAAA AAAAAAAA AAAAAAA
A
A A
A A
A A
A A
A AAAAAAAAAAAA
A
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAA
A
A
A
A
A
AAAAAAAAAAAAAAAAAAAA
AA
AA
A AAAAAA
A
A
A
A
A
AAAAAAAAAAAAAAAAAAAA
A
A
A AAAAAAA
A
A
A
14 A A A A A A A
A SHEAR A
A A
A A
A A
A AA
AA A
A A
A A
A A
A A
A A
A
A
A A
A A
A A
A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A
A A A A A A AA A A A A A A
A A A A A A A A A AA A
A A A A A
15 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A Bay 1 A
A A
A A
A
Bay 2 AA
AA A
A
Bay 3
A
A A
A A
A A
A A
A A
A
16 A
A A
A A
A A
A A
A A
A Col Beam Column Beam Column Beam Col
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A A
A A A A A A A
A
17 A A A A A A Lft Rgt Lft Rgt A Lft Rgt
A A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA
A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
A A A A A A AAAA=-2*I8/I$3 =+I18 AAAA =+M18AAAA AAAAAAAA AAAAAAAA AAAAAAA =+Q18AAAA AAAAAAAA AA
18 A A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA=-2*M8/M$3 AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
=-2*Q8/Q$3 AAAAAAAA
AAAAAAAA
AAAAAA
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAA AAAA
AA AAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AA
A A A A A A AAAAAAAA AAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA AAAA
AAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
19 A A A A A A =+E9 AAA
A A A A A A AAAAAAAA AAAAAAAA=+F9 AA =+F9 AAAAAAAA AAAAAAA =+E9
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A AAAA AAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA AAAA AAAAAAAAAAAAAAAAAAA
A A A A A A AAAA AAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAA
20 A A A A A A =+H19 AAAAAAAAAAAAAAAAAAAA=+K19 AAAAAAAAAAAAAAAAAAAAAAAAAA =+O19 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+S19
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
21 A A A A A A AAAAAAAA AAAAAAAA AAAA=-2*I11/I$3 =+I21 AAAA
AAAAAAAA =-2*M11/M$3 =+M21AAAA AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA AAA =-2*Q11/Q$3
AAAAAAA =+Q21AAAAAAAA
AAAAAAAA AA
AAAAAA
A A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAA
AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAA
AAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAA
AA AAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A AAAAAAAAAAAAAA
A A A A A A AAAA AAAA AAA
22 A A A A A A =+E12 AAAAAAAAAAAAAAAAAAAA=+F12 AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA =+F12 AAAAAAAAAAAAAAAAAAAAAAAAAAA =+E12
A A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA AAAAAAAAAAAAAAAAAAAAAAAA
A
A A
A A
A A
A A
A A
A AAAA=+K22 AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAA=+S22
23 A A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A =+H22 AAAA AAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAA AAAAAA =+O22 AAAA AAAAAAAA AAAAAAAA AAAAAAA
A A A A A A A AAAAAAAAAAAAA
A AAAAAAAAA A AAAAAAAAAAAAAAAAAAAA
AA A AAAAAA A A AAAAAAAAAAAAAAAAAAAA
A A AAAAAAA A
A A A A A A A
A AXIAL FORCE A
A A
A A
A A
A AA
AA A
A A
A A
A A
A A
A A
A
24 A
A A
A A
A A
A A
A A
A A A A A A AA A A A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A A A A A A AA A A A A A A
A A A A A A A
A A
A A
A AA A
25 A
A
A
A
A
A
A
A
A
A
A
A Bay 1 A A A Bay 2 AA
AA
A
A Bay 3
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A
26 A
A A
A A
A A
A A
A A
A Col Beam Column Beam Column Beam Col
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
27 A
A A
A A
A A
A A
A A
A
AAAA AAAAAAAAAAAA AAAA
AAAAAAAAAAAAAAAAAAAA0 AAAA AAAA AAAAAAAAAAAA AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA0
AAAAAAAA AAAAAAAAAAAA AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA 0
AAAAAAAA AAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA
28 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A
A
A AAAA AAAA AAAA
A
A
AAAA
A AAAA
A
A
AAAA
A AAAAAAAA =-I18
AAAA
AAA AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAA
AAAA
AAAA=+J18-M18
AAAAAAAA
AAAA AAAA AAAAAAAAAAAA AAAA
AAAA
AAAA
AAA
AAAA
AAAA AAAA
AAAAAAAA
AAAA AAAA
AAAA AAAA
AAAA
AA
AA =+N18-Q18
AAAA
AA AAAA AAAAAAAAAAAA AAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA
AAAA AAAAAAAAAAAA
AAAA AAAAAAAA
AAAAAAAA AAA=+R18
AAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAA
AAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AA
A
A A A
A A
A A
A A
A
AAAA AAAA
AAAAAAAA
AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAAAAAA AAAAAAA AAAAAAAA AAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAA0 AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA AAAAAAAA
AAAAAAAA
AAAAAA
29 0 0
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A A A A A A AAAA AAAA
AAAAAAAAAAAAAAAAAAAA AAAA AAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAA AAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AA
A
A A
A A
A A
A A
A A
A
AAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAAAA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAA AAAAAAAAAAAAAAAAAAA
30 A A A A A A =+H28-I21 AAAA AAAAAAAAAAAAAAAA=+K28+J21-M21 AAAA =+O28+N21-Q21 AAAAAAAAAAAAAAAAAAAAAAA=+S28+R21
A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AA AAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAA
Chapter 7
Beam
Beam
Beam
Beam
Beam
Beam
Flat slab
one−way slab Flat plate slab
2. Two Way slab: Long span/short span <2. Load is transmitted along two orthogonal
directions.
L
3 If s > 2 than most of the load (≈ ρ5%) is carried in the short directions, Fig. 7.3
4 Load transfer in one way slabs is accomplished hierarchically through an interaction of slab,
11111
00000
00000
11111 11111
00000
00000
11111
00000
11111 Beam 1 00000
11111
00000
11111 00000
11111
1111
0000 1111
0000
0000
1111
0000
1111 0000
1111
1111
0000 0000
1111
0000
1111
B B
Beam 2
Beam 1
Beam 2
Beam 1
S S
L
1111
0000
0000
1111 0000
1111
0000
1111
0000
1111
0000 0000
1111
1111 0000
1111
11111
00000 11111
00000
00000
11111
00000
11111 Beam 1 00000
11111
11111
00000
00000
11111 11111
00000
ρB B
111
000
000
111
P ρA
A 1010 1
0
0
1A
0
1 0
1
000
111
B111
000
Cantilever
supported continuous continuous
Solid One
way slab L/20 L/24 L/28 L/10
Beams or
ribbed One way slab L/16 L/18.5 L/21 L/8
9. Shear does not usually control & no minimum reinforcement is needed (vc = 2 fc )
7–5
10. Principal reinforcement shall not be spaced at more than 3 times the slab thickness nor
18 in (ACI 7.6.5).
11. Usually No. 4 and larger bars are used for flexural reinforcement, as No. 3 may be
bent out of position by workers walking on it. This is more critical for top than bottom
reinforcement.
12. Sometimes, No.3 is used for bottom, and No. 4 for top.
13. Shrinkage/temperature reinforcement shall not be spaced at more than 5 times the slab
thickness nor 18 in (ACI 7.12.2.2).
Net spans
Flexural Design
For maximum spacing, ACI specifies 3h = 3(7.25) = 21.75 in but no more than 18 in,
⇒ smax = 18 in.
ln (1.15)(306)(157)
Vu = 1.15wu = = 2, 302 lb/ft of width (7.9)
2 2
2. Typical interior span
ln (1.0)(306)(166)
Vu = 1.0wu = = 2, 117 lb/ft of width (7.10)
2 2
The shear resistance is
φVc = (0.85)2 f cbw d = (0.85)(2) 3, 750(12)(6.25) = 7, 808lb/f t (7.11)
of the slab
As = 0.0018bh = 0.0018(12)(7.25) = 0.157 in2 /f t (7.12)
and maximum spacing is 18 in. Therefore, we can provide # 4 bars at 15 in. as shrinkage
and temperature reinforcement. They should be placed on top of the lower layer of steel.
Note that in this problem a 6.5 in. thickness was acceptablee for the six interior spans, but a
7.25 in. thickness was required for the end spans.
If the entire floor were made of 6. in. thick slab instead of 7.25 in. about 45 cubic yards of
concrete could have been saved (for a total floor width of about 90 ft) per flor or 180 kips of
dead load per floor. This would represent a considerable saving in say a 20 story building.
In this case, it would be advisable to use 6., and check for delfections in the end spans.
Chapter 8
COLUMNS
Draft
Chapter 9
COLUMNS
9.1 Introduction
1 Columns resist a combination of axial P and flexural load M , (or M = P e for eccentrically
applied load).
tie steel
main longitudinal steel reinforcement
Pipe column
Spiral column
4. Provide ductility
very important to resist earthquake load.
P
Spiral
X Tied X
Corner column
10 bars
12 bars
Wall column
16 bars
14 bars
4 No moment applied,
Elastic Behaviour
P = fc Ac + fs As
= fc (Ac + nAs )
Ultimate Strength
Pd = φPn
Pn = .85fc Ac + fy As
note:
1. 0.85 is obtained also from test data
2. Matches with beam theory using rect. stress block
3. Provides an adequate factor of safety
e P L R
M M
ML MR
L R
e=
M − M
P
n
1. Unsymmetric moments M L = M R
2. Uncertainty of loads (must assume a minimum eccentricity)
3. Unsymmetrical reinforcement
As
7 Assumptions As = As ; ρ = As
bd = bd = fs = fy
Pn
COLUMNS
ε cu
ε cu
P
0
Compression
8 failure range
e = 0; a = h; c =
Radial lines show
Mn Balanced Failure
constant e=
e small Pn ε cu
ε
y
M
0
M
8 There is one specific eccentricity eb = P such that failure will be triggered by simultaneous
1. steel yielding
2. concrete crushing
9 From the strain diagram (and compatibility of concrete and steel strains), Fig. 9.6
εc = .003 (9.1-a)
fy
εy = (9.1-b)
Es
εu .003
c = d= fy
d (9.1-c)
εu + εy + .003
Es
(9.1-d)
Furthermore,
εs εc
= (9.2-a)
c − d c
c − d
⇒ εs = εc (9.2-b)
c
thus the compression steel will be yielding (i.e. εs = εy ) for εc = .003 and d = 2 in if c > 6 in
10 Equilibrium:
Pn
Pn = .85fc ab + As fy − As fs a = .85fc b
.003
fs = fy a = β1 cb Pn,b = .85β1 fc bd fy (9.3)
c = .003
d
+ .003
As = As b fy
+.003
Es
Es
d’
9–5
d
h/2
A A’
s s
b
εs εcs ε’s
A sf y Pn
A sf s
c
c
A sf s
0.85f’c
A’sf s
A’sf y
a
e
e’
or
87, 000
Pnb = .85β1 fc bd (9.4)
fy + 87, 000
11To obtain Mnb we take moment about centroid of tension steel As of internal forces, this
must be equal and opposite to the externally applied moment, Fig. 9.6.
a
Mnb = Pnb eb = .85fc ab(d − ) + As fy (d − d )
2 (9.5)
M
ext
Mint
12 Note: Internal moments due to As fy and As fy cancel each other for symmetric columns.
In this case a and Pn are unknowns, and for failure to be triggered by fy in As we must
have e > eb .
Can still assume As fy = As fy
Pn
ΣFy = 0 ⇒ Pn = .85fc ab ⇒ a = (9.6-a)
.85fc b
a
COLUMNS
Two approaches
where
As As
ρ = bd = bd
fy
µ = .85fc
a = β1 c (9.8-a)
def
fs = fy (9.8-b)
c− d
fs = εc E s ≤ fy (9.8-c)
c
C = 0.85fc ab (9.8-d)
Pn = C+ As fs
− As fy (9.8-e)
h−a h h
Mn = C + as fs − d + As fs d − (9.8-f)
2 2 2
Mn
e= (9.8-g)
Pn
Note this approach is favoured when determining the interaction diagram.
Compression failure occurs if e < eb ⇒ εu = .003, assume fs = fy , and fs < fy
From geometry
εu
c = fs
d
Es + εu
d−c
9–7
⇒ fs = Es εu
c
d − βa1
= E s εu a (9.9-a)
β1
Pn = .85fc ab + As fy − As fs (9.9-b)
a
Pn e = .85fc ab(d − ) + As fy (d − d ) (9.9-c)
2
this would yield a cubic equation in Pn , which can be solved analytically or by iteration.
1. Assume a (a h)
2. Solve for ΣM = 0 with respect to tensile reinforcement & solve for Pn
3. From strain compatibility solve for fs
4. Check that ΣFy = 0 & solve for a
5. If ai+1 = ai go to step 2
In this case
a = β1 c (9.10-a)
d−c
fs = εc Es ≤ fy (9.10-b)
c
c − d
fs = εc Es ≤ fy (9.10-c)
c
C = 0.85fc ab (9.10-d)
Pn = C + As fs + As fs (9.10-e)
h−a h h
Mn = C + As fs − d + As fs d − (9.10-f)
2 2 2
where
ρs minimum ratio of spiral reinforcement
Ag gross area of section
Ac area of core
2. A minimum of 4 bars for tied circular and rect
4. φ increases linearly to 0.9 as φPn decreases from 0.10fc Ag or φP0 , whichever is smaller,
to zero (ACI 9.3.2).
5. Maximum strength is 0.8φP0 for tied columns (φ = 0.7) and 0.85φP0 for spirally reinforced
columns (φ = 0.75).
P d −M d Tension
n
mi
(M Pnb )
control region
e
nb’
eb
0.10f’ c A g
0 φM n Mn M
14 To assist in the design of R.C. columns, design charts have been generated by ACI in term
Pn Mn χe As +As
of non dimensionalized parameters χ = bhf vs bh2 f = h for various ρt where ρt = bh and
c c
fy
µ= .85fc
A 12 by 20 in. column is reinforced with four No. 4 bars of area 1.0 in2 each, at each
corner. fc = 3.5 ksi, fy = 50 ksi, d = 2.5 in. Determne: 1) Pb and Mb ; 2) The load and moment
for c = 5 in; 3) load and moment for c = 18 in.
Solution:
Balanced Conditions is derived by revisiting the fundamental equations, rather than mere
9–9
Tension failure, c = 5 in
def
fs = fy = 50 ksi (9.13-a)
c − d
fs = εc E s ≤ fy (9.13-b)
c
5.0 − 2.5
= (0.003)(29, 000) = 43.5 ksi (9.13-c)
5.0
a = β1 c = 0.85(5.0) = 4.25 in (9.13-d)
C = 0.85fc ab (9.13-e)
= (0.85)(3.5)(4.25)(12) = 152 k (9.13-f)
Pn = C+ As fs − As fy (9.13-g)
= 152 + (2.0)(43.5) − (2.0)(50) = 139 k (9.13-h)
h−a h h
Mn = C + As fs − d + As fs d − about section centroid (9.13-i)
2 2 2
20 − 4.25 20 20
= (152) + (2.0)(43.5) − 2.5 + (2.0)(50) 17.5 − (9.13-j)
2 2 2
= 2, 598 k.in = 217 k.ft (9.13-k)
2, 598
e = = 18.69 in (9.13-l)
139
Compression failure, c = 18 in
17.5 − 18.0
COLUMNS
12"
20"
3" 3"
24"
c
εy
.003
Cc
Balanced Condition:
fy 40
εy = = = .001379 (9.15-a)
Es 29, 000
Victor Saouma Mechanics and Design of Reinforced Concrete
Draft
9.2 Short Columns
εu .003
9–11
Note that the co0mpression steel is yielding because d > 2” and c > 6” (as previously
proven)
Taking moment about centroid of section
12"
20"
3" 3"
h−c−d’ 24"
c=23.5"
εy
ε ε ε
s sc y
.003
e=2.4"
9"
Pn
e’=11.4 h/2=12"
.85f’c
A sf s
A scf Cc A’ sf y
sc
a=20" a/2
1. Assume a = 20 in
a 20
c= = = 23.5 in (9.17)
β1 .85
2. For center steel (from geometry)
εsc .003
= (9.18-a)
c − h2 c
c − h2
⇒ εsc = .003 (9.18-b)
c
fsc = Es εsc (9.18-c)
c− h
2
= Es .003 (9.18-d)
c
23.5 − 12
= 29, 000 .003 = 42.5 ksi > fy ⇒ fsc = fy (9.18-e)
23.5
3. Take moment about centroid of tensile steel bar
a h
Pn e = 0.85fc ab(d − ) + As fy (h − 2d ) + Asc fy ( − d ) (9.19-a)
2 2
Victor Saouma Mechanics and Design of Reinforced Concrete
Draft
9.2 Short Columns
20
9–13
4. Iterate
ΣF = 0 ⇒ Pn = (.85)fc ab + Asc fsc (9.23-a)
= (.85)(3)(7.9)(20) − 2(1.56)(25.3) (9.23-b)
= 403 − 79 = 324 k (9.23-c)
a
ΣM = 0 ⇒ Pn (e + h/2 − d ) = .85fc ab(d − ) + As fy (d − d )
2
d − d
−Asc fsc ( ) (9.23-d)
2
7.9
Pn (24 + 9) = (.85)(3)(7.9)(20)(21 − ) + 4(1.56)(40)(21 − 3)
2
+2(1.56)(25.3)(9) (9.23-e)
Pn (33) = 6, 870 + 4, 493 − 710 = 10, 653 k.in (9.23-f)
√
⇒ Pn = 323 k (9.23-g)
5. Determine Mn
COLUMNS
Design the reinforcement for a column with h = 20 in, b = 12 in, d = 2.5 in, fc = 4, 000 psi,
fy = 60, 000 psi, to support PDL = 56 k, PLL = 72 k, MDL = 88 k.ft, MLL = 75 k.ft,
Solution:
1. Ultimate loads
201
Pu = (1.4)(56) + (1.7)(72) = 201 k ⇒ Pn = = 287 k (9.25-a)
0.7
251
Mu = (1.4)(88) + (1.7)(75) = 251 k.ft ⇒ Mn = = 358 k.ft (9.25-b)
0.7
2. Chart parameters
e (358)(12)
= = 0.75 (9.26-a)
h (287)(20)
h − 2d 20 − (2)(2.5)
γ = = 0.75 ⇒ interpolate between A3 and A(9.26-b)
4
h 20
Pn 287
κ =
= = 0.3 (9.26-c)
bhfc (12)(20)(4)
e
κ = (0.3)(0.75) = 0.225 (9.26-d)
h
4. Reinforcement
ρt = At
bh (0.4)(b)(h)(.85)(fc ) 1 2
fy At = = (0.4)(12)(20)(.85)(4) = 5.45 in(9.27-a)
µ = .85fc fy (60)
Pn
9–15
1111111
0000000
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111 M0y
M0x 0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111 Mny
0000000
1111111
0000000
1111111
Mnx
where
Mnx = Pn ey
Mny = Pn ex
M0x = Mnx capacity at axial load Pn when Mny (or ex ) is zero
M0y = Mny capacity at axial load Pn when Mnx (or ey ) is zero
and α1 and α2 are exponent which depend on geometry and strength.
19 Bresler suggested that we set α1 = α2 = α. For practical purposes, a value of α = 1.5 for
rectangular columns, and between 1.5 and 2.0 for square sections has proven acceptable.
20 An improvement of Bresler equation was devised by Parme. The main assumption is that at
any load Pn , Fig. 9.9
Mny M0y
=
Mnx M0x
or
Mnx = βM0x ; Mny = βM0y
M ny /M0y
COLUMNS
M ny βM 1.0
0x C
M 0y C
β B
B
M 0y βM 0y β
M0x
A
M0x M nx 45
o
A
1.0Mnx /M0x
21 Thus, β is the portion of the uniaxial moment strength permitted to act simultaneously on
the column section. It depends on the cross section, strength, and layout.
22 The usual range is between 0.55 and 0.70, with a recommended value of 0.65 for design.
23 Hence, once β is selected, we can substitute in Bresler’s equation
α
M0x M0y α
βM 0x
+ β M0y = 1.0
β α = 12
α log β = log 0.5
α = log 0.5
log β
thus,
log 0.5/logβ log 0.5/logβ
Mnx Mny
+ = 1.0 (9.28)
M0x M0y
Review of a section
Mny Mnx 1 − β Mny Mnx
+ = 1 If ≥ (9.29-a)
M0y M0x β M0y M0x
Mnx Mny 1 − β Mny Mnx
+ = 1 If ≤ (9.29-b)
M0x M0y β M0y M0x
Design of a column
M0y 1−β Mny M0y
Mny + Mnx = M0y If ≥ (9.30-a)
M0x β Mnx M0x
M0x 1−β Mny M0y
Mnx + Mny = M0x If ≤ (9.30-b)
M0y β Mnx M0x
0.4
0.2
0.0
0.0 0.2 0.4 0.6 0.8 1.0
Mnx/M0x
Pn β
111111
000000
000000
111111 C
000000
111111
000000
111111
M ny /M 0y + M nx /M 0x (1− β/ β ) =1
000000
111111
000000
111111
1.0
α α
000000
111111
000000
111111
1−β
B
(M nx /M 0x ) +(M ny /M 0y) =1
000000
111111
000000
111111
M0y β
M0x 000000
111111
0y
000000
111111
M ny /M
000000
111111
000000
111111
M nx /M 0x + M ny /M 0y (1− β/ β) =1
000000
111111
000000
111111
β
β
000000
111111
000000
111111
000000
111111
000000
111111
Mny 1−β
000000
111111
o
45
A
Mnx M nx /M 0x 1.0
Figure 9.11: Bilinear Approximation for Load Contour Design of Biaxially Loaded Columns
26 Note, circular or square columns with symmetric reinforcement should always be considered
COLUMNS
Determine the adequacy of a 16 in. square tied column with 8 # 9 bars. d = 2.5in, and there
are 3 bars on each side. The section is to carry factored loads of Pu = 144 k, Mux = 120 k.ft
and Muy = 54 k.ft, fc = 3 ksi and fy = 40 ksi. P0 = 952 k, M0x = M0y = 207 k.ft.
Solution:
Mux (120)(12)
ey = Pu = 144 = 10.0 in
Muy (54)(12)
ex = Pu = 144 = 4.5 in
The interaction diagram for e = 10 in, e = 4.5 in and e = 0 will give Pn equal to 254, 486, and
952 kips respectively.
The required load Pn = 144
0.7 = 205 k, the corresponding moments are M0x = M0y = 207 k.ft
from the interaction diagram. Using β = 0.65
120
Required Mnx 0.7
M0x = 207 = 0.828
54
Required Mny 0.7
M0y = 207 = 0.373
Mnx Mny
Note that we could have first solved for M0x , and then determined M0y from Fig. 9.10.
Mny
This would have given M0y ≈ 0.45 which is greater than the actual value, hence the design
is safe.
27Column buckling theory originated with Leonhard Euler in 1744. An initially straight mem-
ber is concentrically loaded, and all fibers remain elastic until buckling occur.
28 For buckling to occur, it must be assumed that the column is slightly bent as shown in Fig.
9.12. Note, in reality no column is either perfectly straight, and in all cases a minor imperfection
P P
x
x and y are
principal axes
x
is present.
29At any location x along the column, the imperfection in the column compounded by the
concentric load P , gives rise to a moment
Mz = −P y (9.31)
d2 y P
2
− =0 (9.33)
dx EI
P
31 Letting k 2 = EI , the solution to this second-order linear differential equation is
32 The two constants are determined by applying the essential boundary conditions
1. y = 0 at x = 0, thus B = 0
2. y = 0 at x = L, thus
A sin kL = 0 (9.35)
This last equation can e satisfied if: 1) A = 0, that is there is no deflection; 2) kL = 0, that is
COLUMNS
no applied load; or 3)
kL = nπ (9.36)
P
2
Thus buckling will occur if EI = nπ L or
n2 π 2 EI
P =
L2
33The fundamental buckling mode, i.e. a single curvature deflection, will occur for n = 1; Thus
Euler critical load for a pinned column is
π 2 EI
Pcr = (9.37)
L2
fp Pcr
Crushing Buckling
−1
tan E
ε (kl/r) lim (kl/r)
37 Le is the distance between two adjacent (fictitious or actual) inflection points, Fig. 9.13
P cr P cr Pcr
i.p.
l/4 i.p.
i.p.
<kl<l
kl=l kl= l l l
2
2
l
i.p.
l/4
i.p.
i.p.
P cr Pcr P cr
P Pcr P
cr cr
i.p.
l l<kl<
l i.p.
l 8
kl=21
kl=1
Pcr
Pcr Pcr
i.p.
l<kl<
8
i.p.
k=2 k=1
38 k is known for some simple highly idealized cases, but for most cases k depends on ΨA + ΨB
COLUMNS
Σ( EI
L )of columns
Ψ= EI
(9.39)
Σ( L )of floor members
P ( EI
( P P
2
( EI
( ln ∆
1
ln
A ψA
A ψA A ψA
( EI
(
2
ln
( EI
(
1
ln
MA MA
MA
MB
MB MB
B ψB
B ψB B ψB
Braced Unbraced
40 Code recommends some minimum eccentricity to account for imperfectly placed load, Fig.
9.17
41 For an eccentrically placed load
1
Mmax = M0 (9.40)
1 − 1−P
P
cr
42 The moment magnification factor reflects the amount by which the beam moment M0 is
Ga K Gb Ga K Gb
∞ 1.0 ∞ ∞ ∞ ∞
50. 50. 20.
10. 10. 100. 10. 100.
50. 50.
5. 5.
30. 5. 30.
3. 0.9 3. 20. 20.
4.
2. 2.
10. 3. 10.
0.8 9. 9.
8. 8.
1. 1. 7. 7.
6. 6.
0.8 0.8
0.7 0.7 5. 5.
0.6 0.6 4. 2. 4.
0.7
0.5 0.5
0.4 0.4 3. 3.
0.3 0.3 2. 2.
0.6 1.5
0.2 0.2
1. 1.
0.1 0.1
0. 0.5 0. 0 1. 0
P e
P
COLUMNS
φP 0
P0(max)
M P
C
P cr
M Pu
B
Pu e Pu ∆
Pn
P∆
in
em
M 0
M 0 M c = δM 2
kl/r
M0 Mn M 0 M2 Mc M
M1
Cm = .6 + .4 ≥ .4 (9.41-b)
M2
where
M1 is numerically smaller than M2 (not algebracially)
M1
M2 >0 if single curvature
M1
M2 <0 if double curvature
Cm < 1 if members are braced against sidesway
Cm =1 if members are not braced against sidesway
44 ACI Code
Lu unsupported length ACI 10.11.1
k ≤ 1.0 braced columns ACI 10.11.2
k ≥ 1.0 unbraced columns ACI 10.11.2
r = .3h rectangular x section ACI 10.11.3
r = .25d circular cross section
r < 34 − 12 M2
kLu M1
braced, neglect slenderness ACI 10.11.4
kL
r < 22 unbraced, neglect slenderness
45 From conventional elastic analysis get Pn &Mn
Mc = δM2 (9.42)
Cm
δ = ≥ 1.0 (9.43)
1 − φP
Pn
cr
π 2 EI
Pn = 10.11.5 (9.44)
(kLu )2
M1
Cm = .6 + 4 (9.45)
M2
Ec Ig
5 + Es Is
EI = (9.46)
1 + βd
Ec Ig
2.5
or EI = (9.47)
1 + βd
MD
βd = (9.48)
MD + ML
βd is the ratio of maximum design load moment to maximum design total load moment (always
A 15 ft long, 14” circular column is connected to 40 ft long 14” by 22” beams. The column
is on the last floor, below it the column is circular and has a 16” diameter.
Given, Pn = 500 k, 14 × 22 has ρ = .015, fc = 5, 000 psi, fy = 40, 000 psi
Solution:
22
Lu = 15 ft − = 13.17 ft (9.49-a)
12
r = .25d = (.25)(14 in) = 3.5 in (9.49-b)
Ec = 57, 000 fc = 57, 000 5, 000 = 4, 030 ksi (9.49-c)
πd4 π(14)4
Ig = = = 1, 886 in4 (9.49-d)
64 64
Ec Ig
EIcol = 2.5 1
1+βd EIcol = (4, 030)(1, 886) = 3, 040, 000 ksi (9.50-a)
βd = 0 2.5
EI 3, 040, 000
= = 16, 890 k.in (9.51-a)
L c (15)(12)
Ig (14)(22)3 1
Ibeam = Icr = = 6, 210 in4 (9.51-b)
2 12 2
EI (4, 030)(6, 210)
= = 52, 140 k.in (9.51-c)
L beam (12)(40)
Σ(EI/L)col 2(16, 890)
ΨA = = = .324 (9.51-d)
Σ(EI/L)beam 2(52, 140)
π(16)4
bottom column I = 64 = 3, 217 in4
L 3
Lu =18’ l =43.3in
111
000
000
111 111
000
000
111
000
111 000
111
Solution:
8.5
22"
22"
224
9–27
⇒ Moment for which the column is to be designed (1.13) (520) = 587 k.ft and Pu = 224
Chapter 10
PRESTRESSED CONCRETE
10.1 Introduction
1 Beams with longer spans are architecturally more appealing than those with short ones.
However, for a reinforced concrete beam to span long distances, it would have to have to be
relatively deep (and at some point the self weight may become too large relative to the live
load), or higher grade steel and concrete must be used.
2 However, if we were to use a steel with fy much higher than ≈ 60 ksi in reinforced concrete
(R/C), then to take full advantage of this higher yield stress while maintaining full bond between
concrete and steel, will result in unacceptably wide crack widths. Large crack widths will in
turn result in corrosion of the rebars and poor protection against fire.
3 One way to control the concrete cracking and reduce the tensile stresses in a beam is to
prestress the beam by applying an initial state of stress which is opposite to the one which will
be induced by the load.
4 For a simply supported beam, we would then seek to apply an initial tensile stress at the
top and compressive stress at the bottom. In prestressed concrete (P/C) this can be achieved
through prestressing of a tendon placed below the elastic neutral axis.
5 Main advantages of P/C: Economy, deflection & crack control, durability, fatigue strength,
longer spans.
6 There two type of Prestressed Concrete beams:
Pretensioning: Steel is first stressed, concrete is then poured around the stressed bars. When
enough concrete strength has been reached the steel restraints are released, Fig. 10.1.
Postensioning: Concrete is first poured, then when enough strength has been reached a steel
cable is passed thru a hollow core inside and stressed, Fig. 10.2.
10.1.1 Materials
7 P/C beams usually have higher compressive strength than R/C. Prestressed beams can have
Vertical Harping
bulkhead Harping
hold-up hold-down
point point
Anchorage Jacks
Jacks Tendon
Jacks
anchorage
Tendon in conduct
Anchorage
Slab Jack
Wrapped tendon
9 Having shown that losses would be too high for low strength steel, we will use
Strands usually composed of 7 wires. Grade 250 or 270 ksi, Fig. 10.3.
0000000
1111111
111111
000000
0000000
1111111
000000
111111
0000000
1111111
000000
111111
0000000
1111111
000000
111111
0000000
1111111
000000
111111
0000000
1111111
000000
111111
0000000
1111111
000000
111111
0000000
1111111
000000
111111
000000
111111 0000000
1111111
000000
111111 000000
111111
111111 0000000
1111111
000000
111111
000000
111111
000000 000000
111111
0000000
1111111
000000
111111
000000
111111
000000
111111 000000
111111
0000000
1111111
000000
111111
000000
111111
000000
111111 000000
111111
000000
111111
000000
111111
000000
111111000000
111111
000000
111111
000000
111111000000
111111
000000
111111
000000
111111000000
111111
000000
111111
000000
111111000000
111111
000000
111111
000000
111111000000
111111
0000000
1111111
0000000
1111111
000000
111111
000000
111111000000
111111
0000000
1111111
0000000
1111111
000000
111111
000000
111111000000
111111
0000000
1111111
0000000
1111111
000000
111111 000000
111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
0000000
1111111
Tendon have diameters ranging from 1/2 to 1 3/8 of an inch. Grade 145 or 160 ksi.
Wires come in bundles of 8 to 52.
Note that yield stress is not well defined for steel used in prestressed concrete, usually we take
1% strain as effective yield.
10 Steel relaxation is the reduction in stress at constant strain (as opposed to creep which
is reduction of strain at constant stress) occurs. Relaxation occurs indefinitely and produces
significant prestress loss. If we denote by fp the final stress after t hours, fpi the initial stress,
and fpy the yield stress, then
fp log t fpi
=1− − .55 (10.3)
fpi 10 fpy
is reduced to:
2. Pi Initial prestress force; But then due to time dependent losses caused by
is reduced to:
3. Pe Effective force
10.1.3 Assumptions
2. section is uncracked
13 Through proper arrangement of the tendon (eccentricity at both support and midspan)
various internal flexural stress distribution can be obtained, Fig. 10.4.
14An equivalent load for prestressing can be usually determined from the tendon configuration
and the prestressing force, Fig. 10.5.
15 The load-deformation curve for a prestressed concrete beam is illustrated in Fig. 10.6.
111
000
000
111
h 000
111
000
111
000
111
f’y
Q fc 2f c
fc
11
00
00
11 111
000
000
111 11
00
00
11
P h/2 00
11
00
11 + 000
111
000
111 = 00
11
00
11
P 00
11 000
111 00
11
fc fc =f t
2Q
0 2f c 2f c
11
00
00 +1111111
11 0000000
0000000
1111111 11
00
00
11
00
11
00
11 0000000
1111111
0000000
1111111 = 00
11
00
11
P 2h/3 00 1111111
11 0000000 00
11
P
2f c 2f =2f 0
t c
0 2f c 2f c
11
00
00 +1111111
11 0000000
0000000
1111111 11
00
00
11
00
11
00
11 0000000
1111111 = 00
11
00 1111111
0000000 00
11
2Q
11 0000000
1111111 00
11
2f c 2f t =2f c 0
fc fc
P Midspan 00
11
P 000
111 11
00
000 +
111
000
111 0 = 00
11
h/2 111
000 00
11
00
11
111
000
h/3 Ends fc
fc
0 f fc
c
00
11
00
11 000
111
111
000 00
11
11
00
Q 00
11 + 000
111 = 00
11
00
11
00
11 000
111
000
111 00
11
00
11
2f c ft =f c fc
P P Midspan
fc fc
h/2 00
11
00
11 00
11
00
11
00
11
00
11 + 0 = 00
11
00
11
h/3 00
11 00
11
fc Ends fc
Figure 10.4: Alternative Schemes for Prestressing a Rectangular Concrete Beam, (?)
(a)
P θ P P sin θ P sinθ
P cos θ P cos θ
2P sin θ
(b)
θP P P sin θ P sin θ
P cosθ P cosθ
(c)
Pe Pe
P e P P
P
(d)
P P θM
P sin θ P sin θ M
e
P cos θ P cosθ
(e)
P PP P sinθ P sinθ
None
P cosθ P cosθ
2P sinθ
(f) P
P None
(g)
P P
Load
PRESTRESSED CONCRETE
Ru
ptu
re
Steel yielding
Service load limit
including Overload
tolerable overload Tn
Service
load
First cracking load range
f cr
Decompression or higher
cgs (f=0)
Balanced
∆ ∆ ∆ Deformation ∆
o D L (deflection of camber)
∆
∆ pi = Initial prestress camber
pe ∆ pe = Effective prestress camber
∆ O = Self−weight deflection
∆ ∆ D= Dead load deflection
pi
∆ L= Live load deflection
Figure 10.6: Load-Deflection Curve and Corresponding Internal Flexural Stresses for a Typical
Prestressed Concrete Beam, (?)
Pi Pi ec1 Pi
ec1
f1 = − + =− 1− (10.4)
Ac I Ac r2
Pi Pi ec2 Pi
ec2
f2 = − − =− 1+ 2 (10.5)
Ac I Ac r
2. Pi and the self weight of the beam M0 (which has to be acconted for the moment the
beam cambers due to prestressing)
Pi
ec1 M0
f1 = − 1− − (10.6)
Ac r2 S1
Pi
ec2 M0
f2 = − 1+ 2 + (10.7)
Ac r S2
Service Load when the prestressing force was reduced from Pi to Pe beacause of the losses,
and the actual service (not factored) load is apllied
3. Pe and M0
Pe
ec1 M0
10–7
f1 = − 1− − (10.8)
Ac r2 S1
Pe
ec2 M0
f2 = − 1+ 2 + (10.9)
Ac r S2
Pe
ec1 M0 + MDL + MLL
f1 = − 1− − (10.10)
Ac r2 S1
Pe
ec2 M0 + MDL + MLL
f2 = − 1+ 2 + (10.11)
Ac r S2
The internal stress distribution at each one of those four stages is illustrated by Fig. 10.7.
Pi Pi e c 1 Pi e c1
(1- )
Ac Ic Ac r2
11
00 11111
00000
00
11 00000
11111 111111111
000000000
00
11 00000
11111 000000000
111111111
00
11
00
11 00000
11111 000000000
111111111
c1
00
11 00000
11111
00000
11111 000000000
111111111
00
11 00000
11111 000000000
111111111
00
11 00000
11111 000000000
111111111
00
11 00000
11111 000000000
111111111
00
11 00000
11111 000000000
111111111
000000000
111111111
00
11 00000
11111 000000000
111111111
e c2 00
11 00000
11111 000000000
111111111
00
11 00000
11111 000000000
111111111
00
11 00000
11111
00000
11111 000000000
111111111
00
11
00
11 00000
11111 000000000
111111111
00000
11111 000000000
111111111
Pi Pi e c 2 Pi e c2
Stage 1 (1+ )
Ac Ic Ac r2
Pi e c1 Mo Pi e c1 Mo
(1- ) - (1- )-
Ac r2 S1 Ac r2 S1
111111111
000000000 111111
000000
000000
111111
000000000
111111111 111
000 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111
000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111 000000
111111
000000000
111111111 000
111
Pi e c2 Mo Pi e c2 Mo
(1+ ) + (1+ )+
Stage 2 Ac r2 S2 Ac r2 S2
Pe e c1 Mo Md + Ml Pe e c1 Mt
(1- )- - (1- )-
Ac r2 S1 S Ac r2 S1
111111
000000 11111111111
00000000000
1
000000
111111 00000000000
11111111111
00000000000
11111111111 111111
000000
000000
111111 00000000000
11111111111 000000
111111
000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111
00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 00000000000
11111111111 000000
111111
000000
111111 000000
111111
Pe e c2 Mo Md + Ml Pe e c2 Mt
(1+ )+ + (1+ )+
Ac r2 S2 S2 Ac r2 S2
Stage 4
Figure 10.7: Flexural Stress Distribution for a Beam with Variable Eccentricity; Maximum
Moment Section and Support Section, (?)
17Those (service) flexural stresses must be below those specified by the ACI code (where the
subscripts c, t, i and s refer to compression, tension, initial and service respectively):
Full prestressing (pioneered by Freysinet), no tensile stresses, no crack, but there are some
problems with excessive camber when unloaded.
19 The ACI code imposes the following limits on the steel stresses in terms of fpu which is the
ultimate strength of the cable: Pj < .80fpu As and Pi < .70fpu As . No limits are specified for
Pe .
7" 6"
4"
24"
7" 6"
2"
5"
4"
The section properties for this beam are Ic = 12, 000 in4 , Ac = 176 in2 , S1 = S2 = 1, 000 in3 ,
r2= AI = 68.2 in2 .
Determine flexural stresses at midspan and at support at initial and final conditions.
Solution:
Pi
ec2
10–9
f2 = − 1+ 2 (10.12-c)
Ac r
169, 000 (5.19)(12)
= − 1+ = 1, 837 psi (10.12-d)
176 68.21
2. Pi and the self weight of the beam M0 (which has to be acconted for the moment the
beam cambers due to prestressing)
(176) in2
w0 = (.150) k/ ft3 = .183 k/ft (10.13-a)
(144) in2 / ft2
(.183)(40)2
M0 = = 36.6 k.ft (10.13-b)
8
The flexural stresses will thus be equal to:
w0 M0 (36.6)(12, 000)
f1,2 =∓ =∓ = ∓439 psi (10.14)
S1,2 1, 000
Pi
ec1 M0
f1 = − 1− 2 − (10.15-a)
Ac r S1
= −83 − 439 = −522 psi (10.15-b)
√
fti = 3 fc = +190 (10.15-c)
Pi
ec2 M0
f2 = − 1+ 2 + (10.15-d)
Ac r S2
= −1, 837 + 439 = −1, 398 psi (10.15-e)
√
fci = .6fc = −2, 400 (10.15-f)
3. Pe and M0 . If we have 15% losses, then the effective force Pe is equal to (1 − 0.15)169 =
144 k
Pe
ec1 M0
f1 = − 1− 2 − (10.16-a)
Ac r S1
144, 000 (5.19)(12)
= − 1− − 439 (10.16-b)
176 68.2
= −71 − 439 = −510 psi (10.16-c)
Pe
ec2 M0
f2 = − 1+ 2 + (10.16-d)
Ac r S2
144, 000 (5.19)(12)
= − 1+ + 439 (10.16-e)
176 68.2
= −1, 561 + 439 = −1, 122 psi (10.16-f)
note that −71 and −1, 561 are respectively equal to (0.85)(−83) and (0.85)(−1, 837)
respectively.
(110)(12, 000)
f1,2 = ∓ = ∓1, 320 psi (10.18)
1, 000
Thus,
Pe
ec1 M0 + MDL + MLL
f1 = − 1− 2 − (10.19-a)
Ac r S1
= −510 − 1, 320 = −1, 830 psi (10.19-b)
√
fcs = .45fc = −2, 700 (10.19-c)
Pe
ec2 M0 + MDL + MLL
f2 = − 1+ 2 + (10.19-d)
Ac r S2
= −1, 122 + 1, 320 = +198 psi (10.19-e)
√
fts = 6 fc = +380 (10.19-f)
5. The stress distribution at each one of the four stages is shown below.
-1830
-510
-522
-83
4 3 2 1
-1122
-1398
-1837
+198
80 ft
CENTER
LINE
ELEVATION OF BEAM HALF
SIDEWALK
52"
10"
3" TRANSVERSE DIAPHRAGM
7" 10"
52"
8.9"
6’-7"
61.2" = 79"
8.9"
10.3.2 Prestressing
22 Each beam is prestressed by two middle parabolic cables, and two outer horizontal ones
along the flanges. All four have approximately the same eccentricity at midspan of 2.65 ft. or
31.8 inch.
23 Each prestressing cable is made up 64 wires each with a diameter of 0.27 inches. Thus the
total area of prestressing steel is given by:
0.276 in 2
Awire = π(d/2)2 = 3.14( ) = 0.0598 in2 (10.21-a)
2
(10.21-b)
2 2
Atotal = 4(3.83) in = 15.32 in (10.21-c)
24 Whereas the ultimate tensile strength of the steel used is 247 ksi, the cables have been
stressed only to 131 ksi, thus the initial prestressing force Pi is equal to
Pi = (131) ksi(15.32) in2 = 2, 000 k (10.22)
10.3.3 Loads
30 The live load is created by the traffic, and is estimated to be 94 psf, thus over a width of
62.5 feet this gives a uniform live load of
1
wLL = (0.094) k/f t2 (62.5) ft = 0.45 k/ft (10.27)
13
31 Finally, the combined dead and live load per beam is
wDL+LL = 0.36 + 0.45 = 0.81 k/ft (10.28)
2. Pi and the self weight of the beam M0 (which has to be acconted for the moment the
beam cambers due to prestressing)
(1.72)(160)2
M0 = = 5, 504 k.ft (10.30)
8
The flexural stresses will thus be equal to:
w0 M0 (5, 50.4)(12, 000)
f1,2 =∓ =∓ = ∓2, 043 psi (10.31)
S1,2 943.
Pi
ec1 M0
f1 = − 1− 2 − (10.32-a)
Ac r S1
= 490 − 2, 043 = −1, 553 psi (10.32-b)
√
fti = 3 fc = +190 (10.32-c)
Pi
ec2 M0
f2 = 1+ 2 + (10.32-d)
Ac r S2
= −3, 445 + 2, 043 = −1, 402. psi (10.32-e)
√
fci = .6fc = −2, 400 (10.32-f)
3. Pe and M0 . If we have 13% losses, then the effective force Pe is equal to (1−0.13)(2×106 ) =
1.74 × 106 lbs
Pe
ec1 M0
f1 = − 1− 2 − (10.33-a)
Ac r S1
1.74 × 106 (31.8)(39.5)
= − 1− − 2, 043. = −1, 616 psi (10.33-b)
1, 354 943.
Pe
ec2 M0
f2 = 1+ 2 + (10.33-c)
Ac r S2
1.74 × 106 (31.8)(39.5)
= − 1+ + 2, 043. = −954. psi (10.33-d)
1, 354 943.
4. Pe and M0 + MDL + MLL
(0.81)(160)2
MDL + MLL = = 2, 592 k.ft (10.34)
8
and corresponding stresses
(2, 592)(12, 000)
f1,2 = ∓ = ∓962. psi (10.35)
32, 329
Thus,
Pe
ec1 M0 + MDL + MLL
f1 = − 1− 2 − (10.36-a)
Ac r S1
= −1, 616 − 962. = −2, 578. psi (10.36-b)
√
fcs = .45fc = −2, 700 (10.36-c)
Pe
ec2 M0 + MDL + MLL
f2 = 1+ 2 + (10.36-d)
Ac r S2
= −954 + 962. = +8. psi (10.36-e)
√
fts = 6 fc = +380 (10.36-f)
Chapter 11
FOOTINGS
property line
P P
P
45
g f
Two-way b c
4 d/2
4
Vc (
Vc= 2+
βc ( f’ c b0d
f’c b0d 2 Beam
Cl a d
Cs d
d/2
0 0.5 1.0 h e
A2
A1
f g
FOOTINGS
a b
9.5"
9.5"
9’-6"
Column
18"x18"
d c
19" 4.00’
2.42’
e h
9’-6"
18"
2’-0"
18"
3"
clear
9’-6"
9’-6"
8-#7-6’-0" 13-#7-6’-0"
18"x24"
19’-6"
11-#9
top
Column 6’-6"
16-#7-6’-3"
Bottom
9"
18’-0" 4’-6"
Dowels same
as col. bars
Grade
3" clear
6’-0"
3" clear 3’-5"
2’-6" 2’-6"
3’-0"
23’-3"
1,149,000
23.25 = 49,400lb./ft.
16’-3" 3’-6"
1’-6" 418,000 lb
2’-0"
9.30’
173,000 lb
385,000 lb Shear
Diagram
3,460,000 in.-lb.
21,400,000 in.-lb.
Moment diagram
Footings
FOOTINGS
figure
Combined footing
Wall Footings
Example
DL = 10 k/f t (including the
wall weight)
LL + 5 k/f t
Masonry wall
qa = 4, 000 psf
← no need to apply ke
overload fact or XXee safety
factor is already including in qa .
15
Required b = 3.875 = 3.87 f t
use b = 4 f t.
Determine thickness hf → controlled by shear
22.5
qu = 4 = 5.625 ksf
= 5, 625 psf
V u = Vc = 2 fc bw d
Vu = φ Vc
√
2 − d)(5625) = 0.85 (2
( 4−1 5, 000)(12)(12)in“f t (d)
1.5 − d = 2.38 d
Use hf = 9 in.
critical section from masonary walls
ACI −
critical section
15.4.2
for concrete columns
or walls
b
a 2
Mu = 1
2 qu 2 − 4
1 2
= 1
2 (5.625) 2 − 4
= 8.61 f t − kips
Mn = Mu
φ = 8.61
0.9 = 9.57 f t − kips
φfy
Mn = φ (b)(d)2 fy 1 − 0.59
fc
φ(40)
9.57 × 12 = φ (12)(5.32)2 (40) 1 − 0.59 3
93142 − 118 φ + 1 = 0
φ = 0.0091
Use # 6 bars
Ab 12 0.44 × 12
S = As /12 = As /Ab = 0.58 = 9.1
0.04(0.44)(40,000)
= √
3,000
= 12.85 in.
Column footings
figure
Failure Modes
Shear Strength
Punching Shear
ACI − 11.12.2
Vc = 2+ 4
βc fc b0 d
b
βc = a for b > a
b0 = α[(a + d) + (b + d)]
or Vc = αs d
b0 + 2 fc b0 d
αs = 40 int. cols.
30 edge cols.
20 corner cols.
or Vc = 4 fc b0 d
Shear strength is larger under two-way action than under one-way action because of tri-axial
stress.
As βe → very large, Ve = 2 fc b d ← for beams
Beam Shear
Ve = 2 fc bd
← critical section
V u ≤ φ Vc
figure
β+1
Total Reinf. in
short direction
:2
β = :1
Example
DL = 235 k, LL = 115 k
↓
18 square
fc = 3, 000 psi
fy = 40, 000 psi
qc = 5, 500 psf
hf
7f t. (max.)
Assume hf = 2
(235+115)1,000
Required A = 5,200 (7) = 9.6
Use A = 9 − 8
Determine hf
Pu 525 × 1,000
qu = A = (7)(9.67) = 7.756 psf
Punching Shear
) 2 *
Vu = 7756 (7)(267) − 1812 + d
φ Vc = φ (2 + 4
βc ) fc b0 d or φ 4 fc b0
βc = 1
√
φ Vc = (0.85)(4) 3, 000 (4)(18 + 12d)(12)
.
αs d
or φ Vc = + 2 fc b0 d
b0
will not be critical
φ Vc = Vu
/ 0
10 (7)(9.67) − ( 18
12 + d)
2 = (18 + 12d)(12d)
Beam Shear
4−67
Vu = 7, 756 2 − 9
12 − d (7)
φ Vc = φ 2 f bd
√
= (0.85)(2) 3, 000 (7 × 12)(12d)
0.528(4.085 − d) = d
d = 1.5 f t = 18 in.
use d = 18 in
= 22.5 in
Select hf = 23 in
Bending:
figure
Long direction:
(4.085)2
Mu = 7.76 (7) 2 = 453 f t. − kips
Mn = Mu
φ = 504 f t. − kips ⇒ As = 8.5 in2
14 − #7
Short direction:
(2.75)2
Mu = 7.76 (9 − 67) 2 = 284 f t. − kips
Mn = 284
0.9 = 315 f t − kips = 5.5 in2
9 − #7
φg = 0.002
8 − #7
figure
min As = 0.005 Ag
gross area
of column
ACI − 15.8.2.1
Chapter 12
DEEP BEAMS
DEEP BEAMS
Examples of occurance
tanks
folded plates
figure
All of these are plane stress problems, and stresses can not be found by classical elastic
theory because plane sections do not remain plane after bending (Bernoville-Novier Hypothesis
is not valid any more).
need 20 analysis i) elasticity
ii) finite difference
iii) finite element
Deep beam design
figure
• Usually deep beams are shear critical & not flexure critical by reducing the span, momen-
tum reduced but shear remains constant
Draft
12–2
M
• plane section do not remain plane ⇒ r = Iy + y = VIbQ are wrong
XX XX
& we have a warping of the x sections tend to relieve compressive stresse @ top
might get more than one neutral ones
stress trajectary
• cracks will form at almost vertical directions & thus web reinforcement are not very
efficient ⇒ horz. steel more efficient main steel mostly distributed @ bottoms 13 depth
J becomes irrelevant what cracking there is, as long as we have this mechanism.
m
before cracking fs = As J d
• deflection for tied arch is larger than for beam (because stress is larger): but we need to
watch out for bond failure, are hooks or to be the steel out & find against the plate.
• better to use horizontal hook XXXXX instead of vertical hook because might have a
failure along weak face
figure
• FAILURE by
Ln
d
Av ≥ .0015 bw S
Avh ≥ .0025 bw S2
S ≤ d
+ ≤ 18
5
S2 ≤ d
3 d ≤ 18 A.C.I. 11.9
Introduction