GS 462/194
GULF STANDARD
1
2.
3.
32
33
34
35
3.6
SINGLE - USE RIGID AND SEMI - RIGID PLASTIC CUPS
AND CONTAINERS FOR PACKAGING BEVERAGES,
MILK PRODUCTS, AND ALLIED PURPOSES
SCOPE AND FIELD OF APPLICATION
This Gulf standard specifies general re:
semi-rigid plastic cups, containers and cl a
products, and allied purposes. It includes measurings
containers and methods of industry.
quirements for single - use rigid and
losures for packaging beverages, milk
of these cups and
Notes:
1) The requirements of this specification in respect of product contact
surfaces could be applied also to the purchase of other single -use
containers such as those of composite construction or made from plastics
= coated paper board.
2) The word (product) mentioned in the subject means cups and containers
specified in this standard.
METHOD OF INDUSTRY
The product is prepared by moulding or injection and the moulds shall be made
from stainless steel and shall be highly smooth. Chromium plated moulds are
preferable.
GENERAL REQUIREMENTS
The product material shall comply with the approved Gulf standard for that
material, It shall be homogeneous and free from foreign materials, swelling, air
pockets and industry defects.
The surfaces of the product shall be homogeneous in colour and shining.
Product material shall not have any hazard effects on the public health and
shall not cause changes in construction and properties of the prepackaged
material.
Product material shall be free from adour and taste affectis i
ing the
the prepackaged material, a
Product thickness shall be proportional to its shape and purpose of use.
The product shall not have any changes in shape or dimentions before
y changes i
Packaging when the product is stored in a place of a temperature range between
~ 50°C and + 50°C in the shadow,GS 462/1994
GULF STANDARD
3.7 The product shall resist dangers of transportation and handling without
. breakage can ims
ating ink and colouring matter used for plastic shall comply with the
a concerned. apr P d and shall be non-migratory to the
a2
3.10
3.10.1
3.10.2
3.10.3,
3.
3.12
4.
42
43
concerned approved Gulf standar:
prepackaged substance.
Cups edges shall be flat and not sharp-cut for well sealing to prevent
permeability of air or other things as protection for the prepackaged material.
Product closures shall be designed for well sealing according to one of the
following designs or others:
Closure well sealed by heat on the top surface of the rim.
Closure well sealed by pressing.
Closure well sealed by twisting around the low surface of the rim.
Product closures shall be suitable, such that when the product is filled and
inverted, the closure will remain in position and there will no leakage of the
prepackaged material.
The cups shall be tested bacteriologically according to the specified standard
method to make sure tlie absence of any contamination before handling in the
markets and packaging.
MEASUREMENTS
Cups and containers shall be manufactured according to its purpose for use. It
shall met general requirements mentioned in item (3).
Preferred standard capacities
Cups and containers standard capacities preferred to be according to the
following series:
1000, 500, 250, 200, 175, 150, 125, 100, 75, and 50 cm3
Cups and containers manufactured from poly styrene
The following table declaring capacity, wei imenti
; pacity, weight and di
containers manufactured from ploy yen mention ofthe cups anGs 462/1994
GULF STANDARD
ima eager maT one
(mm)
Tabna Cup To00 [22 12 125 0.25 - 0.45
Labna Cup 500 7 (3) 125 035
Labna Cup 250 12 39 128 035
Drink Cup 250 8 100 70 0.25 - 0.30
Drink Cup 200 6 83 70 0.30- 0.40
Drink Cup 150 5 62 70 035 - 0.45
Drink Cup 100 4 48 10 0.20 - 0.30
Juice Cup 200 7 2 B 0.25 - 0.45
Juice Cup 190 8 93 15 0.35 - 0.45
Juice Cup 175 6 80 B 0.25 - 0.45
Juice Cup 125 5 38 B 0.45
‘Yogurt Cup 200 | 3-8 | 60 90 0.40 - 0.45
Drinking water Cup | 95 4 64 64 020
Ices Cup 25 | 56 | 54 79 035
Tees Cup 100 6 31 B 0.25 - 0.35
Tees Cup 80 s 44 B 0.35 - 0.45
Tees Cup 50 4 37 B 0.25 - 0.45
5. TOLERANCES
5.1 Thickness
52
S21
5.2.2
Wall thickness tolerance shall be & 5 % if the maximum wall thickness is not
specified
Rim dimentions
Round rim diameter
The tolerance on the outside rim diameter shall be + 0.3% from the nominal
diameter, or agreed diameter, or + 0.2 mm, whichever is the greater. (Diameter
can be known by measuring the circumference and dividing by 7).
Circularity
Any outside rim diameter, measured directly, shall not differ from the diameter
determined as in clause 5.2.1by more than 1.0% or 2 mm, whichever is the
— atcimeGULF STANDARD GS 462/194
5.23 In case of other rim shapes, the tolerance shall be as agreed between the
purchaser and the supplier.
6. LABELLING
The following information shall be declared on the product in Arabic
language*. It shall be part form the product and shall be easy to read.
61 Product name and its registered trade mark
62 ‘The statment "Produced in "in case of local production
63 Nominal capacity in metric u
64 Any other information agreed between purchaser and the supplier.
PACKAGING
7 Each group of the product shall be packed immediately after manufacture in a
suitable outer container, complying with the concerned approved standard, to
protect the product from breakage, dirt and collecting of dust
72 Direction for cleaning or any other precautions for using shall be declared on
the outer containers or in an attached lable, such as "cups and containers used
one way"
‘TESTING METHODS
The product shall be tested according to th concerned approved standard
* Tris permitted to use other language in addition to Arabic.