Professional Documents
Culture Documents
TCBC-HT Running Manual 2021 Rev B
TCBC-HT Running Manual 2021 Rev B
TCBC-HT
RUNNING MANUAL
The contents of this field operation manual are regarding Threaded and Coupled Buttress Connectors – High
Torque. Included are the necessary gear, pre-make up, make up, and inspection procedures and techniques to
ensure safe and proper operation of the string while maximizing longevity of the product. This manual is to be
used in conjunction with the specific guidelines provided with the product.
Thread Compound
TCBC-HT requires Best-O-Life 2000 thread compound for optimal performance.
Using a new bucket of thread compound is recommended to avoid contamination. Also stir the
compound to ensure it is mixed evenly.
Applying thread compound too generously may have a negative affect the performance of the
connection. A light coat applied to the BOX END of the connection is all that is necessary to get
optimum results (see “Proper Doping” in the Makeup Procedures).
Use of a moustache brush is highly recommended for applying thread compound to the box
end.
Under no circumstances is a bottle type brush is approved.
Do not mix different thread compounds as incompatibility may exist between thread
compounds.
Stabbing Guides
Stabbing guide is recommended for running TCBC-HT strings as it protects the pin nose and
threads from damage.
Revision: B Page | - 2 -
Necessary Tools for Running (continued)
Strap Wrench
A properly-sized strap wrench may prove useful when installing accessories to the string.
Power Tongs
TCBC-HT connector must be tightened to the correct torque values in order achieve optimum
results. The torque equipment must have a capacity of at least 40% more than the
recommended make-up torque. The reason for this is that if a connection has to be backed out
the torque may be higher than make-up torque. The tong must have a variable speed control
and be capable of operating at <1 RPM for final make-up.
Handling Plug
It is highly recommended that a handling plug be used when inserting any tool into the box end
to ensure no damage to the connection.
Revision: B Page | - 3 -
Pre-Job Procedures:
Cleaning:
Clean the entire Pin and Box and make sure that all the storage compound, dirt, dust has been
removed.
Also a varsol type solution with a soft brush is acceptable. DO NOT USE A WIRE BRUSH!
Timing is everything! In the event that the threads are cleaned but the run is delayed it is
recommended to apply a WD-40 type solution or thread compound to the pin or box end to
help fight corrosion.
Always protect your connectors!
Visual Inspection
Prior to running, glance over the tubes to ensure no physical damage has occurred during
transport and off-loading.
Also check the pin and box end to ensure no corrosion or surface imperfections and /or damage
has occurred.
Revision: B Page | - 4 -
Makeup Procedures:
Verifying Torques
Verify all torques by using the appropriate Connection Data Sheet and that all torque monitoring
equipment values are entered correctly.
Stabbing Guide
Affix a stabbing guide onto the box and subsequently guide the pin along the box’s axis until the
threads interact.
Be sure to keep the two components vertically aligned and to carefully fit them together.
Revision: B Page | - 5 -
Makeup Procedures (Continued):
Makeup RPM
Initial stab: Low gear, to confirm that no threads have been crossed.
Running threads in: High gear, no more than 30 RPM.
Final make-up: Low gear, no more than 5 RPM.
Shoulder Information
The TCBC-HT connection will achieve a shoulder in the final makeup.
If the TCBC-HT connection does not achieve a shoulder when using thread compound but has
thread interference during makeup; break the connection out three (3) revolutions and then
proceed to remake connection up again with torques adjusted to near maximum torque.
If no thread interference is present in the torque graph prior to shoulder engagement then the
connection shall be broke out and cleaned and further inspected.
Coupling Spin
The coupling shall not spin no more than 1/3 turn. In the event that spin does occur install
backups to the coupling and continue makeup.
Revision: B Page | - 6 -
Interchangeability
TCBC-HT is interchangeable with buttress.
Highly recommended to thread lock ANY buttress thread when rotating is anticipated.
Make up the connections to the base of the ∆ on the pin. Treat these makeups as a position only
makeup regardless of torque.
Field Repair
Only a qualified H.I.S. Technician shall perform field repairs.
Damaged connectors that are not repairable and should be separated immediately and labeled
as “REJECT” and not utilized.
Thread root and crest can be repaired as long as the single thread doesn’t extend more than
50% of the circumference. Use of a file is the safest way to repair threads.
Spot repairing the circumference of the threads is accepted.
Any damages to the face of the coupling are repairable with a file.
Rotating Down-hole
TCBC-HT “Maximum Working Torque” that is displayed on our Connection Data Sheet, is in no
way a sustainable rotating torque. Sustaining these torque values at great lengths could
possibly have unfavorable results.
The H.I.S TCBC-HT connection shall never be rotated above “Maximum Working Torque”
(provided on Connection Data Sheet) and RPM should be limited to 30 RPM or less.
It is always recommended to start off rotating with minimum torque and 10-15 rpm. If not
successful jump up Torque and RPM’s in increments. Care should be taken to slowly increase
and decrease torque when rotating, this allows the stored kinetic energy to dissipate and
prevent down-hole connection yielding and backing off.
It is recommended by H.I.S to have a certified thread representative on location at all times.
When running the casing and tubing, seeing problems as they develop will ensure proper operation of the product
as well as save you from larger troubles during. Use the following guidelines during makeup to curtail any serious
and costly problems from developing during operation.
Revision: B Page | - 7 -
Torque Graphs
Accepted Makeup Curves
Shown in Figure 1 is a typical example of an ideal makeup curve that would be observed with
TCBC-HT. The torque value gradually increases until an abrupt spike is reached, indicating the
shoulder interaction.
Slight oscillations are acceptable (as shown in Figure 2) in the increasing torque value, but the
general scope of the curve in Figure 1 should be maintained.
Figure 2 show a hump in the upward slope of the curve and a less defined spike from the
shoulder.
Which is probably the most commonly seen of them all, shows an ascending curve lacking much
of a hump, but a torque shoulder “spike” is still very noticeable.
All such curves are still within the acceptable range of makeup behaviors, so the makeup
procedure can continue without interruption in these cases.
Revision: B Page | - 8 -
The user has superior knowledge about all aspects of the wellbore and well site operations
and therefore assumes all risk associated with casing and connection related issues that
occur during and after rotating operations. In addition, dynamic operations, such as rotating
casing, need to be monitored by a qualified and experienced professional who understands
all potential issues and can make informed decisions to reduce the associated potential risks.
Contacts
If any questions arise regarding the running procedure or any problems encountered, please notify any
of the following contacts:
Revision: B Page | - 9 -