Professional Documents
Culture Documents
TGeneral Partner
echnical worl d ®
SAMSUNG. SC-428PS.
SAMSUNG. SC-428PSL.
SAMSUNG. SC-428PT.
SAMSUNG. SC-428PTL.
6 Alignments and Adjustments
6-2 SC-428PT/PTL
6 Alignments and Adjustments
1. Adjust VR102R (R-BIAS) and VR102B (B-BIAS) 10 Turn the contrast and the brightness controls
so that the back raster color appears white to fully clockwise.
the unaided eye. 11 Adjust the focus control of the FBT to display
3
_. Set the brightness control (VR502) to the the sharpest image possible. (R-GAIN) and
mechanical center position and the contrast VRlOlB (B-GAIN) display a white color.
control (VR501) to the maximum position.
12. Recheck the color coordinates at 3ft-L lumi-
3. Change the video signal to the 60mm square nance and check the white color with rotating
green pattern of the 48.3 kHz/60 Hz. the contrast control (VR501). If there is some
error, retry the adjustment from (2).
4. Adjust the VRlOlG (G-GAIN) so that the
luminance of the green square is 4Oft-LQft-L. 13. Recheck the back raster after disconnecting the
signal cable.
5. Change the video signal to the full white Luminance tolerance 3.5ft-L - 15ft-L
pattern of the 48.3 kHz/bO Hz.
Conditions
Direction : Monitor facing east.
Display image : White flat field.
L u m i n a n c e : Cutoff point at the center of
display area.
SC-428PT/PTL 6-3
6 Alignments and Adjustments
1 I I
ia
/
I i
j Erner 1 0.4 1 0.25 ( SC-428PTiPTL 1
/ I I I
J
B
Samsung SOD CRT
191 mm
A 1’ Setup Bolt 2: Bow Magnet 3: Band
Red and Blue Alignment Red and Blue and Green Alignment
@?-pole magnet movement) (6-pole magnet movement)
M(R,B) G
G
MRBI
I misalignment
M(R,B) G
,G,
M(R,B)
Cross-Hatch Pattern
6-4 SC-428PT/PTL
6 Alignments and Adjustments
Static convergence involves the alignment of the Use the following procedure to correct minor :
red, blue and green lines in the center area of the .dynamic (edge) misconvergence. If, after using
display. this procedure, dynamic misconvergence is still
See “Dynamic Convergence” for alignment of the greater than the 0.4 mm tolerance around the
color fields around the edges of the display. periphery of the display area, replace the CRT.
Conditions
Direction : Monitor facing east 1. Make sure the display is not affected by
Warm-up : 30 minutes external magnetic fields.
Display image : Crosshatch pattern
2. Make sure the static convergence is properly
Tolerances : See Table 6-1
adjusted.
As shown in Figure 6-5, CRTs used in these moni- 3. Strategically place small magnetic strips
tors all have the same magnet configuration as on the back of the CRT to correct the
shown in table 6-2 below. misconvergence. Be careful not to remove the
Table 6-2. Magnet Configurations paper protecting the adhesive on the magnetic
. strip until you are satisfied with their
placement and the dynamic convergence.
,MCFIT ;;;::Z_G,:
ag”‘;tEY iiont Of CRT 4. When you are satisfied with the convergence
around the edge of the CRT, permanently glue
the magnets to the back of the CRT.
Use the following steps to correct any static
misconvergence: Warning Do not remove the factory
1. Locate the pair of four-pole magnet rings. installed wedges. These wedges
were installed by the CRT manu-
2. Unlock the rings and rotate the individual ? facturer and are properly placed
rings (change the spacing between tabs) to 0 for this CRT. Removal may result
A
converge the vertical red and blue lines. in damage to the CRT.
9-3-2 Main & CRT Socket PCB Parts List ( A : Caution, l : Specialty part for this monitor only, A ES0 Caution)
19
I’
CAPACITORS -
Cl00 O.lUF,-20/80%,5OV,-20/85 1237101045
ClOlR lOuF20%.50V,RT 1119501068
ClOlG lOuF20%,50V,RT 111950106B
ClOlB 1OuF 20%,50V,RT 1119501068
Cl026 4.7uF 20%,50V,RT 1119504758
C102G 4.7uF 20%,50V,RT 1119504758
ClOZR 4.7uF 20%.50V,RT 1119504758
Cl038 33PF,20%.5OV-25/85 1218203303
C103G 33PF,20%,5OV-25/85 1218203303
C103R 33PF,20%,5OV-25/85 1218203303
Cl046 luF20%,160VRT 1119701057
C104G 1uF 20%,160V:RT 1119701057
C104R 1uF 20%,160V,RT 1119701057
C105B lOuF20%,50V,RT 111950106B
C105G lOuFZO% 50VRT 1119501068
! ClOSR lOuF20%:50V:RT 111950106B
@ Cl066 O.OlUF.-20/80%,5OOV, 1233501033
C106G O.OlUF,-20/80%,5OOV, 1233501033
C106R O.OlUF,-20,'80%.5OOV, 1233501033
Cl07 lOuF20%50VRT 1119501068
Cl08 1OOuF ZOi,l6i,RT 111920~078
Cl09 O.lUF,-20/80%,5OV.-20/85 1237101045
Cl10 1OOuF 20%,16V,RT 1119201078
Cl11 lOOuF20%,16V,RT 111920107B
Cl12 lOOuF20%,16V,RT 111920107B
Cl13 O.lUF,-20/80%.5OV,-20/85 1237101045
Cl14 O.lUF,-20/80?'0,5OV,-20/85 1237101045
Cl15 47uFZO%,lOOV,RT 1119604761
Cl16 O.OlUF,-20/80%,5OOV. 1233501033
Cl17 2700PF,10%,2KV,-25/85'C,RT 1233202728
Cl18 O.OlUF,-20/80%,5OOV, 1233501033
Cl19 3.3uF 20%,250V,RT 1119803358
Cl20 O.lUF,-20/80%,5OV,-20/85 1237101045
Cl23 1OOuF ZO%,lGV,RT 111920107B
czoo 100uF20%,16V,RT 111920107B
2202 O.lUF,-20/80%.5OV,-20/85 1237101045
2203 lOuF20%,50V,RT 1119501068
C204 O.lUF,-20/80%.5OV,-20/85 1237101045
c205 1OOuF 20%,16V,RT 1119201078
C206 0.0022UF.10%,1OOV.RT,CQ92MT 1312602226
c207 33PF,20%,5OV-25/85 1218203303
C208 47PF,5%,50V,-25/85'C,RT 1218204707
c209 47PF,5%,50V.-25/85'C,RT 1218204707
c210 O.lUF,-20/80%,5OV,-20/85 1237101045
c211 O.lUF,-20/80%,5OV.-20/85 1237101045
c301 1OOuF 20%,50V,RT 1119501078
c305 0.068UF,10%,100V,RT 1312606832
c310 33PF,20%,5OV-25/85 1218203303
c304 47OuF '20%,25V,RT 1119304773
c401 1OOOuF 20%,16V,RT 1119201084
C402 022UF,10%.100V,RT 131620224B
c403 1uF 20%,50V,RT 1119501058
c404 0.047UF,10%,100V,RT 1312604734
c405 0.001UF.10%,100V,RT 1312601021
C406 0.1UF,10%,100V,RT.CQ92MT 1312601045
S1 S2 S3 S4
S5 S6 S7
S8