Professional Documents
Culture Documents
Product Catalogue: Page Summary Table
Product Catalogue: Page Summary Table
This Product Catalogue is provided to ensure easy and accurate identification of gear drives for ordering
purposes.
To browse the catalogue you have two options:
1. Use the titled section links below to jump straight to the information you desire.
2. Use the page number sequence at the top and bottom of the page to browse the catalogue one
page at a time.
Table of contents
Page Summary Table
Index Product catalogue introduction & table of contents Contents
1 (You are here.)
8-11 Horsepower and thrust ratings (standard, extra heavy, opposed, solid
shaft, combination)
12-13 Propeller & vertical turbine pump drives (fan cooled)
14-16 Dimensions & standard clutch dimensions
(standard gear drives only)
For any questions or enquiries please contact the factory via the contact randolph page.
1
Table 01 | Table 02
Model Number and ratio (input to output speed), Thrust Requirements, Rotation, Horsepower Requirement, Pump Head, Shaft
Size. We define the ratio as the ratio of horizontal input RPM to the vertical output RPM).
EXAMPLE: A 2:3 ratio gear drive operating at 1760 RPM output would have 1173 RPM input.
ROTATION: Shown below are four (4) possible rotations. Number one (1) is considered standard. Unless noted differently, the
drive will be manufactured to this configuration. Numbers two (2), three (3) and four (4) are special rotations and are
manufactured when specifically requested.
MODEL
MINIMUM THRUST REQUIREMENTS
FOR STANDARD BEARING ARRANGEMENT
TABLE 1
F30
NO MINIMUM DOWNTHRUST
RATIO: 1:2 4:7 2:3 3:4 4:5 5:6 10:11 1:1 11:10 6:5 5:4 4:3 3:2 7:4 2:1
G, M, 40 25,643 23,390 20,486 20,434 20,381 19,518 19,589 18,462 1,000 17,565 17,442 17,428 15,330 13,605 13,253
(R)
G,M, 60
(R)
G,M, 80
2
(R)
G, M, 100
(R)
G125 (R)
M150 (R)
G150
M200 (R)
G200A
18,638 16,386 17,424 15,558 14,502 15,224 14,907 13,130 1,000 1,000 1,000 1,000 1,000 528 1,074
G250
G300
G350
G400
G450
NO MINIMUM DOWNTHRUST
F, M500
F590
F750
F1000
F1200
F1500
P16AH
NO MINIMUM DOWNTHRUST
P20A
P22
P24B
P30B
Note: For rotation No's. 2,3, & 4 contact factory, check TABLE 5 for downthrust on all combination, solid shaft, opposed
bearings, and some extra heavy thrust bearings.
VERTICAL RPM 340 430 580 690 720 870 960 1,160 1,460 1,760 2,000 2,200 2,400 2,600 2,800 3,000 3,460 3,600
PERCENT OF HP AT 33 38 46 53 54 61 65 74 89 100 105 111 116 122 *128 *133 *146 *150
1,760 RPM
PERCENT OF 170 160 145 137 135 126 122 115 106 100 96 93 90 88 86 84 82 80
THRUST
Note: To obtain horsepower and thrust bearing ratings for the speeds listed, multiply the horsepower and thrust bearing
rating at 1,760 RPM by the percentage in TABLE 2.
* Contact factory.
3
Models designated with "M" are reduced in size
All models with NO fan cooling are designated by a suffix
"R" on the model number
AGMA Service Factor of 1.5 on all models
FM on most models
4
DIMENSIONS
COMBINATION DRIVES
TABLE 3
MODEL: F30 M40 / G40 / G100 M150 M200 G150 G250 G300 G350 F500 / P200 P20A
60 / 80 60 / / 125 / / 400 590 /
/ 100 80 200A 750
RCD N/A 25 1/16 29 1/2 29 1/2 29 1/2 N/A 38 38 N/A N/A N/A N/A N/A
CENTRIFUGAL
RCD 15
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
AUTOMATIC 1/4
RCD MANUAL N/A 23 27 1/2 27 1/2 27 1/2 31 1/8 33 9/16 33 9/16 33 9/16 35 1/4 45 3/8 33 9/16 31 1/2
RAG 22
33 1/2 38 38 38 38 9/16 45 9/16 45 9/16 45 9/16 45 3/8 59 3/4 45 9/16 43 5/8
3/8
RK MANUAL N/A 7/8 7/8 7/8 7/8 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 1 1 1/16 1
RBD 10
16 1/2 20 20 20 20 24 7/16 24 7/16 24 7/16 24 7/16 24 1/2 24 7/16 24 1/2
1/4
RAJ 9 1/8 14 3/4 14 3/4 14 3/4 14 3/4 14 3/4 14 3/4 14 3/4 14 3/4 14 3/4
14 3/4 &
14 3/4
14 3/4 &
23 23
RBF 4-
4-11/16 8-11/16 8-11/16 8-11/16 8-11/16 8-11/16 8-11/16 8-11/16 8-11/16 8-13/16 8-11/16 8-13/16
13/32
RAK 8.249 13.499 13.499 13.499 13.499 13.499 13.499 13.499 13.499 13.499 13.498 13.499 13.498
RN 3/8 5/8 3/4 3/4 3/4 3/4 7/16 7/16 7/16 7/16 5/8 7/16 5/8
APPROX. NET 135 430 575 590 590 750 1010 1010 1010 1090 1600 865 1050
WT. LBS
DOMESTIC WT. 150 460 605 620 620 780 1045 1045 1045 1125 1675 900 1090
LBS.
EXPORT WT. 175 545 712 727 727 900 1230 1230 1230 1310 1865 1085 1195
LBS.
EXPORT CUBE 3.5 10.7 13.0 13.0 13.0 13.2 34.0 34.0 34.0 34.0 57.0 34.0 19.0
FT.
All other dimensions and oil capacity are the same as standard gear drive.All models are standard sprag type non-reverse
except centifugal which has no non-reverse protection.
5
IRRIGATION AND INDUSTRIAL PUMP DRIVES
Models designated with "M" are reduced in size
All models with NO fan cooling are designated by a suffix "R"
on the model number
AGMA Service Factor of 1.5 on all models
FM on most models
1,460 730 973 1,095 1,226 1,460 1,738 1,947 2,190 2,920
1,760 880 1,173 1,320 1,478 1,760 2,095 2,347 2,640 3,520
N/A N/A N/A N/A N/A N/A
2,200 1,100 1,467 1,650 1,848 2,200 2,619 2,933 3,300 -
M40 / M40R M60 / M60R 430 287 323 344 358 386 430 480 516 538 573 645
M80 / M80R M100 / 1,160 773 870 928 967 1,040 1,160 1,294 1,392 1,450 1,547 1,740
M100R
1,460 973 1,095 1,168 1,217 1,309 1,460 1,628 1,752 1,825 1,947 2,190
N/A N/A N/A N/A
1,760 1,173 1,320 1,408 1,467 1,578 1,760 1,963 2,112 2,200 2,347 2,640
2,200 1,467 1,650 1,760 1,833 1,972 2,200 2,454 2,640 2,750 2,933 *3,300
2,600 1,733 1,950 2,080 2,167 2,331 2,600 2,900 3,120 *3,250 *3,467 -
G40 / G40R G60 / G60R 430 220 244 287 323 344 358 386 430 480 516 538 573 645 748 860
G80 / G80R G100 / 1,160 593 659 773 870 928 967 1,040 1,160 1,294 1,392 1,450 1,547 1,740 2,017 2,320
G100R G125 / G125R
M150 / M150R 1,140 746 830 973 1,095 1,168 1,217 1,309 1,460 1,628 1,752 1,825 1,947 2,190 2,539 2,920
1,760 900 1,000 1,173 1,320 1,408 1,467 1,578 1,760 1,963 2,112 2,200 2,347 2,640 3,061 *3,520
2,200 1,124 1,250 1,467 1,650 1,760 1,833 1,972 2,200 2,454 2,640 2,750 2,933 *3,300 - -
2,600 1,329 1,477 1,733 1,950 2,080 2,167 2,331 2,600 2,900 3,120 *3,250 *3,467 - - -
M200 / M200R 430 323 344 358 387 430 478 512 538 573
1,160 870 928 967 1,044 1,160 1,289 1,392 1,450 1,547
1,460 1,095 1,168 1,217 1,314 1,460 1,622 1,752 1,825 1,945
N/A N/A N/A N/A N/A N/A
1,760 1,320 1,408 1,467 1,584 1,760 1,956 2,112 2,200 2,347
2,200 1,650 1,760 1,833 1,980 2,200 2,444 2,640 2,750 *2,933
2,600 1.950 2,080 2,167 2,340 2,600 *2,889 *3,120 *3,250 *3,467
G150 430 215 246 287 319 341 365 386 430 479 507 541 579 645 753 843
1,160 580 663 773 862 921 984 1,041 1,160 1,293 1,367 1,461 1,562 1,740 2,030 2,275
1,460 730 834 973 1,085 1,159 1,239 1,310 1,460 1,627 1,721 1,839 1,965 2,190 2,555 *2,864
6
1,760 880 1,006 1,173 1,307 1,398 1,493 1,579 1,760 1,961 2,074 2,216 2,369 *2,640 *3,080 *3,452
2,200 1,100 1,257 1,467 1,634 1,747 1,867 1,974 2,200 2,451 2,593 - - - - -
G200A / G250 / G300 430 215 246 287 319 341 365 386 430 479 507 541 579 645 753
1,160 580 663 773 862 921 984 1,041 1,160 1,293 1,367 1,461 1,562 1,740 2,030
1,460 730 434 973 1,085 1,159 1,239 1,310 1,460 1,627 1,721 1,839 1,965 2,190 2,555
1,760 880 1,006 1,173 1,307 1,398 1,493 1,579 1,760 1,961 2,074 2,216 2,369 *2,640 *3,080
2,200 1,100 1,257 1,467 1,634 1,747 1,867 1,974 2,200 2,451 2,593 - - - -
G350 / G400 430 287 323 344 358 392 430 472 516 541 579 645
1,160 773 870 928 967 1,058 1,160 1,272 1,392 1,461 1,562 1,740
1,460 973 1,095 1,168 1,217 1,331 1,460 1,601 1,752 1,839 1,965 2,190
N/A N/A N/A N/A
1,760 1,173 1,320 1,408 1,467 1,605 1,760 1,930 2,112 2,216 2,369 *2,640
2,150 1,433 1,613 1,720 1,792 1,960 2,150 2,358 2,580 *2,707 *2,894 *3,225
F500 / F590 F750 430 219 249 287 323 344 358 387 430 478 516 538 573 645
1,160 591 672 773 870 928 967 1,044 1,160 1,289 1,392 1,450 1,547 1,740
1,460 744 845 973 1,095 1,168 1,217 1,314 1,460 1,622 1,752 1,825 1,947 2,190
N/A N/A
1,760 897 1,019 1,173 1,320 1,408 1,467 1,584 1,760 1,956 2,112 2,200 2,347 2,640
7
Table 05 | Table 06
G/M80 G/M80R 430 30 SEE TABLE 1 8,800 SEE TABLE 1 11,200 0 6,400
8
1,760 80 5,500 7,000 0 4,000
9
1,160 222 12,650 0 18,975 0 5,750
10
2000 788 0 18,600 0 28,800 0 18,600
11
PROPELLER AND VERTICAL TURBINE PUMP DRIVES
TABLE 6
340 10,000 100 680 100 858 100 1,020 100 1,190 80 1,360 75 1,530 70 1,700
430 9,600 115 860 115 1,085 115 1,290 115 1,505 90 1,720 85 1,935 80 2,150
500 8,700 125 1,000 125 1,262 125 1,500 125 1,750 100 2,000 95 2,250 85 2,500
P16AH 580 8,600 140 1,160 140 1,464 140 1,740 140 2,030 110 2,320 105 2,610
720 8,000 165 1,440 165 1,817 165 2,160 165 2,520
340 10,500 180 694 180 850 170 1,041 170 1,190 170 1,360 165 1,530 135 1,700 130 1,836 130 2,012
430 10,000 200 878 200 1,075 200 1,317 200 1,505 200 1,720 205 1,935 170 2,150 165 2,322 165 2,544
500 9,500 230 1,021 230 1,250 230 1,531 230 1,750 230 2,000 230 2,250 195 2,500 185 2,700 185 3,000
P20A 580 9,000 250 1,185 250 1,450 250 1,776 250 2,030 250 2,320 250 2,610
720 8,500 300 1,470 300 1,800 300 2,205 300 2,520
340 27,000 265 668 260 836 255 1,020 250 1,190 250 1,360 240 1,530 210 1,700 200 1,870
430 24,000 330 845 320 1,057 315 1,290 310 1,505 310 1,720 300 1,935 260 2,150 260 2,365
500 22,500 375 983 365 1,229 360 1,500 355 1,750 355 2,000 340 2,250 300 2,500
P22
580 22,000 430 1,140 420 1,426 415 1,740 410 2,030 410 2,320
250 30,000 290 491 290 615 260 750 250 875 220 1,000 220 1,125 220 1,250 180 1,375
340 27,000 395 668 395 836 345 1,020 330 1,190 290 1,360 290 1,530 290 1,700 240 1,870
430 24,000 500 845 500 1,057 425 1,290 410 1,505 360 1,720 360 1,935 360 2,150 300 2,365
P24B 500 22,500 580 983 580 1,229 490 1,500 450 1,750 410 2,000 400 2,250 400 2,500
580 22,000 650 1,140 650 1,426 560 1,740 505 2,030 470 2,320
720 20,000 765 1,415 765 1,770 675 2,160 595 2,520
12
250 35,000 390 750 375 875 365 1,000 350 1,125 300 1,375
340 33,000 515 1,020 500 1,190 485 1,360 475 1,530 425 1,870
430 31,000 635 1,290 615 1,505 600 1,720 600 1,935 560 2,365
P30B
500 29,000 725 1,500 705 1,750 686 2,000 686 2,250
13
Table 07a | Table 07b
DIMENSIONS
TABLE 7a
F, G, or M, designates "with fan cooling" - Model No. with suffix "R" has NO fan: Example - M200R
MODEL F30 M40 / G40 / G100 / M200 G150 G250 G350 G450 F500 / F1000 F1200
60 / 80 60 / 125 / / 300 / 400 M500 590 / / 1500
/ 100 80 M150 200A 750
AJ 9 1/8 14 3/4 14 3/4 14 3/4 14 3/4 18 1/4 18 1/4 18 1/4 18 1/4 23 23 28 3/4
14
AK 8.252 13.501 13.501 13.501 13.501 13.501 13.501 13.501 13.501 13.501 13.501 22.005
BB 5/16 x
3/8 x 3/16
3/8 x
5/8 x 5/16
5/8 x
5/8 x 5/16 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 7/8 x 7/16
7/8 x
7/8 x 7/16
5/32 3/16 5/16 7/16
BF 13/32 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 13/16 13/16 13/16
BXmax. 1 1 1/2 1 1/2 1 1/2 1 15/16 1 15/16 1 15/16 2 3/16 2 3/16 2-15/16 2-15/16 4 1/4
BXmin. 3/4 3/4 3/4 3/4 1 3/16 1 3/16 1 3/16 1 1/2 1 1/2 1 11/16 1 11/16 2 15/16
CC 1.249 1.874 1.874 2.249 2.437 2.437 2.937 2.937 2.937 3.749 3.749 3.749
CD 11 3/4 17 5/8 22 9/16 22 5/8 24 7/8 29 3/16 29 3/16 31 9/16 32 3/4 40 13/16 40 13/16 37 3/4
F (FAN) 2 5/8 3 15/16 3 1/2 3 1/2 4 1/2 4 1/8 4 1/16 3 3/8 3 3/8 3 7/8 3 7/8 7 1/2
G 3/8 13/16 7/8 7/8 7/8 7/8 7/8 7/8 7/8 1 3/4 1 3/4 1 3/4
H 5 7/16 8 1/2 11 7/16 11 7/16 11 7/16 13 3/4 13 3/4 13 3/4 13 3/4 18 3/4 18 3/4 16
J (SPRAG 2 7/8 3 13/16 4 5/16 4 1/2 4 1/2 3 15/16 4 13/16 4 5/8 4 5/8 6 7/8 6 13/16 5
N.R.)
K (SPRAG 4 1/2 6 9/16 6 7/16 6 3/16 6 3/16 8 1/4 8 1/4 8 1/4 8 1/4 8 3/4 9 13/16 12 1/2
N.R.)
K (PIN TYPE - 5 5/8 5 3/4 5 1/2 5 1/2 7 3/16 7 3/16 7 1/8 7 1/8 - - -
N.R.)
L 2 1 1/4 1 1/2 1 1/2 1 1/2 1 3/4 1 3/4 1 3/4 1 3/4 1 1/4 1 1/4 2 3/8
Mnps 1/4 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
O 2 7/8 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 7 1/2 7 1/2 10
P - 1 3/4 1 7/8 1 7/8 1 7/8 2 1/2 2 1/2 2 1/2 2 1/2 1 1/4 1 1/4 2 1/4
Q - 3 1/8 3 3/4 3 3/4 3 3/4 4 1/2 4 1/2 4 1/2 4 1/2 3 3/16 3 3/16 11 7/16
Rnps - 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
S - 4 1/2 4 5/8 4 5/8 4 5/8 5 7/8 5 7/8 5 7/8 5 7/8 1 1/4 1 1/4 2 1/4
NET WT. 64 250 320 335 380 680 690 740 745 1500 1810 3000
DOMESTIC 75 275 345 360 406 718 728 778 783 1547 1857 3100
WT.LB.
EXPORT 92 340 420 435 480 820 830 880 885 1720 2030 3250
(WOOD) LB.
EXPORT CU. 2.8 9.5 9.5 9.5 10.3 17.5 17.5 17.5 17.5 38.9 38.9 55.0
FT.
15
OIL CAP 1.5 6 7 7 7 13 13 13 13 24 24 80
QTS.
NOTE: Table is for standard Gear Drives only. For solid shaft, opposed, or EHT bearings, contact factory for dimension print.
STANDARD CLUTCH
DIMENSIONS
TABLE 7b
16
17
Table 08a | Table 08b
DIMENSIONS
TABLE 8a
F, G, or M, designates "with fan cooling" - Model No. with suffix "R" has NO fan: Example - M200R
MODEL F30 M40/ G40/ G100/ M200 G150/ G250/ G350/ G450 F500/ F1000 F1200/
60/ 60/ 125 200A 300 400 M500 590/ 1500
80/ 80 M150 750
100
AJ 9 1/8 14 3/4 14 3/4 14 3/4 14 3/4 18 1/4 18 1/4 18 1/4 18 1/4 23 23 28 3/4
AK 8.252 13.501 13.501 13.501 13.501 13.501 13.501 13.501 13.501 13.501 13.501 22.005
BB 5/16 x
3/8 x 3/16
3/8 x
5/8 x 5/16
5/8 x
5/8 x 5/16 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 7/8 x 7/16
7/8 x
7/8 x 7/16
5/32 3/16 5/16 7/16
18
BD 10 16 1/2 16 1/2 16 1/2 16 1/2 20 20 20 20 24 1/2 24 1/2 30 1/2
BF 13/32 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 13/16 13/16 13/16
BXmax. 1 1 1/2 1 1/2 1 1/2 1 15/16 1 15/16 1 15/16 2 3/16 2 3/16 2-15/16 2-15/16 4 1/4
BXmin. 3/4 3/4 3/4 3/4 1 3/16 1 3/16 1 3/16 1 1/2 1 1/2 1 11/16 1 11/16 2 15/16
CC 1.249 1.874 1.874 2.249 2.437 2.437 2.937 2.937 2.937 3.749 3.749 3.749
CD 11 3/4 17 5/8 22 9/16 22 5/8 24 7/8 29 3/16 29 3/16 31 9/16 32 3/4 40 13/16 40 13/16 37 3/4
F (FAN) 2 5/8 3 15/16 3 1/2 3 1/2 4 1/2 4 1/8 4 1/16 3 3/8 3 3/8 3 7/8 3 7/8 7 1/2
G 3/8 13/16 7/8 7/8 7/8 7/8 7/8 7/8 7/8 1 3/4 1 3/4 1 3/4
H 5 7/16 8 1/2 11 7/16 11 7/16 11 7/16 13 3/4 13 3/4 13 3/4 13 3/4 18 3/4 18 3/4 16
J(SPRAG 2 7/8 3 13/16 4 5/16 4 1/2 4 1/2 3 15/16 4 13/16 4 5/8 4 5/8 6 7/8 6 13/16 5
N.R.)
K (SPRAG 4 1/2 6 9/16 6 7/16 6 3/16 6 3/16 8 1/4 8 1/4 8 1/4 8 1/4 8 3/4 9 13/16 12 1/2
N.R.)
L 2 1 1/4 1 1/2 1 1/2 1 1/2 1 3/4 1 3/4 1 3/4 1 3/4 1 1/4 1 1/4 2 3/8
Mnps 1/4 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
O 2 7/8 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 7 1/2 7 1/2 10
P - 1 3/4 1 7/8 1 7/8 1 7/8 2 1/2 2 1/2 2 1/2 2 1/2 1 1/4 1 1/4 2 1/4
Q - 3 1/8 3 3/4 3 3/4 3 3/4 4 1/2 4 1/2 4 1/2 4 1/2 3 3/16 3 3/16 11 7/16
Rnps - 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
S - 4 1/2 4 5/8 4 5/8 4 5/8 5 7/8 5 7/8 5 7/8 5 7/8 1 1/4 1 1/4 2 1/4
NET WT. 64 250 320 335 380 680 690 740 745 1500 1810 3000
DOMESTIC 75 275 345 360 406 718 728 778 783 1547 1857 3100
WT.LB.
EXPORT
(WOOD) 92 340 420 435 480 820 830 880 885 1720 2030 3250
LB.
EXPORT CU. 2.8 9.5 9.5 9.5 10.3 17.5 17.5 17.5 17.5 38.9 38.9 55.0
FT.
19
NOTE: Table is for standard Gear Drives only. For solid shaft, opposed, or EHT bearings, contact factory for dimension print.
STANDARD CLUTCH
DIMENSIONS
TABLE 8b
20
21
How To Order...
To order or make any enquiries regarding the gear drives listed on www.randolph.net.au please
contact the production factory directly.
Please limit enquiries to weekdays, within normal business hours (7:30am - 4:00pm).
Contact Us
contact details | location map
As a company that prides itself on excellence and high quality, Randolph Manufacturing
Company Australia, is more than willing to assist you in gaining information about, or making
enquiries regarding:
• The Company
• Randolph right-angle gear drives
• Product details and specifications
• Ordering
• Purchases and warranties
• Installation/maintainance
• Anything at all regarding Randolph Right-Angle Gear Drives
Please feel free to contact us any weekday within normal business hours (7:30am - 4:00pm).
Details
Sales Manager: Chris Roden
Email: Pro8819@bigpond.net.au
22