Professional Documents
Culture Documents
Installation instructions.
installation time
The installation time is about 3.0 hours. This may deviate depending on the condition and equipment of the vehicle.
On vehicles without already verbautem bus interface, the installation time will increase by approximately 0.5 hours.
In the specified installation time, the time required for programming / coding is not considered. The clearing of the total costs for the
programming time is when calculating retrofitting costs to loading into account (reimbursement through warranty may not take place).
Important instructions
These installation instructions are establishments primarily for use in the BMW dealership organization and by authorized BMW service.
is the target group for these installation instructions in each case on BMW cars qualified personnel with appropriate expertise.
All work must be performed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational
order using the prescribed tools (special tools) and observing current safety regulations.
If you experience installation or function problems, debugging to about 0.5 hours for mechanical or 1.0 hour for electrical
work.
To avoid unnecessary extra effort to avoid and reduce costs, send immediately via the Aftersales Assistance Portal (ASAP) a request to
the technical parts support. Please include the following:
- VIN,
not archive the hard copy of these installation instructions since daily update ASAP!
pictograms
! Denotes instructions that draw your attention to dangers. Denotes instructions that draw
your attention to special features. Marks the end of Caution-or note text.
Additional cables / lines must be secured with cable ties. If the specified PIN chambers are occupied, bridges, double or parallel
connections will need to be performed. All the figures show LHD cars; on RHD cars is accordingly proceed accordingly. After installation,
the retrofit must have the path - conversions - be programmed / coded.
chapter page
2. Preparations. , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 5
4. Installation reversing camera and retrofit wiring sets and connect it. , , , , , , , , , , , , , , , , , , , , , , 7
6. circuit diagram. , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 12
B button tailgate
C backup camera
D cover
e adapter cable
F Retrofit wiring harness (bus interface)
G Bus interface
H The cable tie (10 Units)
I lug
ISTA no.
Opening the plug housing and removal of the contacts of different plug systems 61 ... 13
Handling of documents: tightening torques repair instructions, technical specifications, purchase 00 11 ...
GN B41 * 1B
A3 female contact 15N On line of PDC controller B41
0.35 mm² PIN 9
GN R3 * 1B
A4 female contact K_CAN3_H at the bus interface R3 / G
0.17 mm² PIN 22
WS R3 * 1B
A5 female contact K_CAN3_L at the bus interface R3 / G
0.17 mm² PIN 9
GN A42 * 1B
A7 female contact composite + At Head Unit A42
0.17 mm² PIN 21
WS A42 * 1B
A8 female contact composite - At Head Unit A42
0.17 mm² PIN 24
umbrella A42 * 1B
A9 female contact umbrella At Head Unit A42
0.17 mm² PIN 23
OR A258 * 8B
F3 female contact K_CAN3_H at BDC A258
0.17 mm² PIN 44
BRGE A258 * 8B
F4 female contact K_CAN3_L at BDC A258
0.17 mm² PIN 43
Make sure that all cables and plug connections are laid
rattle-free. junction A1, Socket housing 8-pin. BL-view camera
to return C infected.
All vehicles
junction A2, BR cable in chamber connector of the mass support point Z10 * 7B infected. junction A3, Green cable, to the connector B41 *
- junction A5, White cable, to PIN 9 branch A6, Cable color SW, insulate and tie back (not
required). feeders A7-A9 to the installation head unit. Retrofit wiring harness A with cable ties H fix on
- the notes ask for the work with ISTA / P in the ISTA / P application documentation note
- Retrofitting "rearview camera" on the path - conversions - select and execute action plan drawn up
- If necessary, perform vehicle testing system by ISTA and ensure that registered the fault memory, if necessary, execute
Legend A1
* Socket housing 8-pin. BL at reversing camera C * infect
A2 * Double flat spring contact, to joint connector of mass support point Z10 * 7B infect
A3 * Socket contact with line out connector B41 * 1B solder
A4 * Socket contact, in plug R3 * 1B the bus interface R3 einpinnen
A5 * Socket contact, in plug R3 * 1B the bus interface R3 einpinnen
A6 * Socket contact insulate and tie back
A7 * Socket contact, in plug A42 * 1B the Head Unit A42 einpinnen
A8 * Socket contact, in plug A42 * 1B the Head Unit A42 einpinnen
A9 * Socket contact, in plug A42 * 1B the Head Unit A42 einpinnen
C* backup camera
G* Bus interface
I* lug
A258 * 8B Socket housing 54-pin. SW, at BDC A258 A24 * 1B Socket housing
8-pin. BL at reversing camera A42 C * 1B Socket housing 40-pin. SW, to Head Unit A42
B41 * 1B Socket housing 18-pin. SW, to control unit PDC B41 R3 * 1B Socket
housing 26-pin. SW, the bus interface R3 Z10 * 7B Earth post boot, rear right
All designations marked * only apply to these installation instructions or this circuit diagram.
cable colors
BL blue GR Gray RT red
BO Bordeaux L-GN light green SW black
BR brown NT nature TR Transparent
GE yellow OR orange VI violet
GN green RO pink WS White