Professional Documents
Culture Documents
The LBAZ and JBA hangers provide higher loads for 2x10, 2x12
and 2x14 members in 14 gauge and 18 gauge steel, respectively.
The nail locations on the JBA enable effective use with nailers.
The B and BA hangers are cost effective hangers featuring
B
• Use specified fasteners; see General Notes and nailer B
table notes.
LB JB
• LBAZ, BA, B and HHB may also be welded to steel headers Nailer
with weld size to match material thickness (approximate 11⁄2" min. attachment
per Designer
thickness shown). The minimum required weld to the top
flanges is 8" x 2" (8" x 1 7⁄16" for LBAZ) fillet weld to each side
of each top flange tab for 14 and 12 gauge and 3⁄16" x 2" fillet
weld to each side of each top flange tab for 7 gauge. Distribute
the weld equally on both top flanges. Welding cancels the top
C-C-2017 © 2017 SIMPSON STRONG-TIE COMPANY INC.
147
Simpson Strong-Tie® Wood Construction Connectors
JB212A 2 1 7⁄16
JB214A (6) 10d (2) 10d x 1 2" 315 — — 1,445 1,015 I10,
LB26 12 1 5⁄16 (4) 16d (2) 10d x 1 2" 290 — — 1,380 860 L11, FL
LB28 See 12 1 5⁄16 (4) 16d (2) 10d x 1 2" 290 — — 1,270 790
2x 14 1 9⁄16
LB210AZ p. 154 (6) 16d (2) 10d x 1 2" 380 — — 1,865 1,330
LB212AZ 2 1 7⁄16
LB214AZ (6) 10d (2) 10d x 1 2" 380 — — 1,705 1,220
(16) 10d (2) 10d x 1 2" 265 3,230 3,630 3,080 2,425
BA min.
See (16) 16d (2) 10d x 1 2" 265 4,015 3,705 3,435 2,665
4x 14 3 9⁄16 pp. 3 2 7⁄16
154–159 (16) 10d (8) 10d x 1 2" 1,170 3,555 3,630 3,625 2,465 I19,
BA max.
(16) 16d (8) 10d x 1 2" 1,170 4,715 4,320 3,800 2,665 L14, FL
See See (14) 10d (6) 10d x 1 2" 990 3,575 3,195 3,625 2,190
3x, 4x B 12 pp. pp. 22 22
154–159 154–159 (14) 16d (6) 10d x 1 2" 990 4,135 3,355 3,800 2,650
1. Uplift loads are based on DF/SP lumber and have been increased for wind or earthquake loading with
no further increase allowed. Reduce where other loads govern.
2. For SPF use 0.86 x DF/SP uplift load.
3. Where noted for single-ply joist hangers use (6) 10d x 1 2" nails.
4. Nails: 16d = 0.162" dia. x 3 2" long, 10d = 0.148" dia. x 3" long, 10d x 1 2" = 0.148" dia. x 1 2" long.
See pp. 26–27 for other nail sizes and information.
Nailer Table
Allowable Loads
148
Simpson Strong-Tie® Wood Construction Connectors
B hanger sloped down and skewed left with sloped top flange installation.
When ordering, specify low side flush, center flush or high side flush.
Specify
angle
Specify
angle
Specify
angle
Typical B Sloped
Typical B Sloped Down Typical B Sloped Down Down on Nailer
Installation with Full Backing with Top Flange Open Non-Backed
149