Professional Documents
Culture Documents
2
1 4 HNUT 0.3750-16-D-C_HNUT 0.3750-16-D-C 3/816 NYLON LOCK NUT
13
3 2 1 SS-4-SAE-7_4_2 SAE 4 TO 1/4NPT
3 1 BM PH50H2KP SHAKER M OTOR
D 4 2 WASHER 0.500-WIDE_Preferred Wide FW 0.5 1/2 WASHER D
5 2 HNUT 0.5000-13-D-C_HNUT 0.5000-13-D-C 1/2-13 NYLON LOCK NUT
6
6 2 HBOLT 0.5000-13x2x1.25-N_HBOLT 0.5000-13x2x1.25-N 1/2-13 X 1-1/4 HEX HEAD CAP SCREW
7 8 WASHER 0.375-WIDE 3/8 WASHER
8 2 M ale Hex Nipple, NPT_SS-8-HN_1_2 1/2 NPT HEX NIPPLE
9 1 SS-8-RB-4 1/2 NPTM TO 1/4 NPTF BUSHING
100085
10 1 Control Valve - 0.5NPTF 1/2 NPT NEEDLE VALVE
11 4 HBOLT 0.3750-16x2x2-C_HBOLT 0.3750-16x2x2-C 3/8-16 X 2 HEX HEAD CAP SCREW
11
12 1 SS-8-T_3 1/2 NPT TEE
9
13 1 SS-4-SAE-7_4_3 O-RING FOR ITEM 2
100078 2 100078 - PURCHASE BEARING ECCENTRIC LOCK PILLOW BLOCK 1X2X5"
C C
100085 1 100085 - PURCHASED (KEYWAY M ATCHED TO M OTOR) 1IN SHAFT COUPLING WITH SET SCREW
100048 1 100048 - SEE DETAIL M OUNTING WELDM ENT
8
100077 1 100077 - SEE DETAIL HAM M ER ASSEM BLY
12
8
B B
10
HAMMER ASSEMBLY
NAME DATE PROJECT:
DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS
100048 MOUNTING WELDMENT CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
SHAKER ASSEMBLY
1 DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
7 +-.5 +-.1 +-.03 +-.005
100078 LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
100078 FURTHER INFORMATION GO TO: 100076 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
4 5 THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
C C
B B
A A
SIZE DWG. NO.
B 100076
REV
A
CEB PRESS SCALE: NONE SHEET 2 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
2
13
D D
3
C C
100085
8
9
12
B B
8
10
A A
SIZE DWG. NO.
B 100076
REV
A
HYDRAULICS ONLY
SCALE: NONE SHEET 3 OF 3
8 7 6 5 4 3 2 1
D D
1.496
38.00 mm 1.000
25.40 mm
C C
100078
4.134
105.00 mm
100085
5.512
140.00 mm
1.000
25.40 mm
1.750
B B
44.45 mm
1.311
33.30 mm
.500
12.70 mm
.375
9.53 mm
NAME DATE PROJECT:
DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS, SHAKER ASSY
CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100078, 100085 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 1
8 7 6 5 4 3 2 1
100074
D D
Item Num ber Quantity Part Nam e Description
100043 100106 2 100106 1/4 X 2 X 2 HR ANGLE X 16IN LONG
100105 2 100105 1/4 X 2 X 2 HR ANGLE X 10IN LONG
100043 1 100043 1/2 X 4 X 4 HR ANGLE X 8IN PER DETAIL
100074 1 100074 11GA HR SHEET 10 X 19 PER DETAIL
100047 2 100047 1IN REBAR X 7IN
100042 1 100042 1/2 X 4 X 4 HR ANGLE X 21IN PER DETAIL
100042
100105
100106
C C
100047
100047
B B
100105
100106
NAME DATE PROJECT:
DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS, SHAKER ASSY
CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
MOTOR MOUNT DETAIL 100048
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100048 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
20"
508 mm
C C
6 1/2"
B B
6 1/2"
165 mm
165 mm
A A
10" 2 1/2" 2 1/2"
254 mm 64 mm 64 mm
16"
SIZE DWG. NO.
B 100048
406 mm REV
A
SCALE: NONE
CEB PRESS, SOIL SHAKER SHEET 2 OF 2
8 7 6 5 4 3 2 1
2 3/16"
56 mm
D D
8"
203 mm
4"
102 mm
C 1 29/32" C
48 mm
100043
4 1/8" 1/2"
105 mm 13 mm
5/8"
16 mm
3 3/8" n 1/2" 2 1/16"
n13 mm
86 mm 52 mm
B B
4" 3 1/2"
102 mm 89 mm
1/2"
13 mm
4" NAME DATE PROJECT:
102 mm DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS, SHAKER ASSY
CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
100043
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100043 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 1
8 7 6 5 4 3 2 1
1 1/4"
32 mm
D D
21"
533 mm
C C
100042
3/4" typ.
19 mm 4 1/8"
105 mm
7/8" 2 1/16"
22 mm 1 1/4" 52 mm
2 3/8" 32 mm
60 mm 3"
76 mm
B B
4"
102 mm
1/2" 1/2"
4"
13 mm 13 mm
102 mm
1"
25 mm
NAME DATE PROJECT:
DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS, SHAKER ASSY
CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
100042
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100042 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 1
8 7 6 5 4 3 2 1
D D
19"
483 mm
C C
10"
254 mm
100074
1 1/2"
38 mm
45.00 ˚
B
3/4" .79 radians
B
19 mm 3"
6" 76 mm
6 1/2" 152 mm
165 mm 6 1/2"
165 mm
1/8"
3 mm
NAME DATE PROJECT:
DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS, SHAKER ASSEMBLY
CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
100074
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100074 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 1
8 7 6 5 4 3 2 1
2"
50.8 mm
D D
1"
25.4 mm
100046
2"
50.8 mm
100044
6" 100045
152.4 mm
C 1" C
25.4 mm
5"
127.0 mm
n 3/8" Item Num ber Quantity Description
n9.5 mm 100046 1 1IN CR ROUND BAR X 8" PER DETAIL
100044 1 1 X 2 HR FLAT BAR X 5" PER DETAIL
100045 1 1 X 2 HR FLAT BAR X 6" LONG
3/8"
9.5 mm
7 1/4"
B 184.2 mm B
7 1/2"
190.5 mm
1"
25.4 mm
1/4" NAME DATE PROJECT:
6.4 mm
DRAWN BEDDINGFIELD
2011/12/17
CEB PRESS, SHAKER ASSY
CHECKED DESCRIPTION:
APPR.
A A
UNLESS OTHERWISE SPECIFIED
HAMMER ASSEMBLY
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100077 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 2
8 7 6 5 4 3 2 1
Item Num ber Part Nam e Quantity Description
100022 100022 2 1/4 X 2-1/2 HR FLAT BAR X 36IN LONG
100023 100023 2 1/2 X 2 HR FLAT BAR X 36IN LONG
100024 100024 1 1/2 X 4 X 7 HR ANGLE X 12IN LONG
100024 100025 100025 100025 1 1IN HR PLATE 7 X 12 D
D
100028 100028 1 1/2 X 3 HR FLAT BAR X 3IN LONG PER DETAIL
100028 100029 100029 1 1/2 X 6 HR FLAT BAR X 12IN LONG
100030 100030 2 1/4 HR PLATE 7 X 13-1/2
100029 100031 100031 1 1/2 X 6 HR SQUARE TUBE X 12IN LONG
100032 100032 1 11GA HR SHEET 8 X 12-1/2
100022
C C
100030
100023
B B
100032
100031
NAME DATE PROJECT:
100022 DRAWN BEDDINGFIELD
12/18/11
CEB PRESS
CHECKED DESCRIPTION:
100023
APPR.
A A
UNLESS OTHERWISE SPECIFIED
DRAWER ASSEMBLY 100026
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100026 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 4
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
C C
B B
A A
SIZE DWG. NO.
B 100026
REV
A
CEB PRESS SCALE: NONE SHEET 2 OF 4
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
100032 100031
D D
100029
WELD ALL SEAMS WHEREVER POSSIBLE
5 100029 100030
127.0 mm 8 100025
203.2 mm
100030 100032
100024
100022
C C
1/2
13 12.7 mm
330.2 mm 100023
1 9 1/2
25.4 mm 241.3 mm 100025
GRIND WELDS
FLUSH ON THIS
SURFACE
100023
B
100030
100022
B B
A 5 3/4 6
100028
146.0 mm 152.4 mm
12 1/2
317.5 mm
5 3/4
146.1 mm
GRIND WELDS
FLUSH ON THIS
SURFACE
PARALLEL WITHIN 1/16IN OF SURFACE A
PARALLEL WITHIN 1/16IN OF SURFACE B
A A
SIZE DWG. NO.
B 100026
REV
A
CEB PRESS SCALE: NONE SHEET 3 OF 4
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
8
203.2 mm
6 12
100029
D 152.4 mm D
100024 304.8 mm
100032 12 1/2
317.5 mm
12
304.8 mm
7
177.8 mm
C C
100030 13 1/2 100031
7 342.9 mm
100025
177.8 mm
12
304.8 mm
12
B 304.8 mm B
6
152.4 mm
2 1/2
63.5 mm 36
914.4 mm
100022
2 36
A 50.8 mm 914.4 mm A
100023
SIZE DWG. NO.
B 100026
REV
A
CEB PRESS SCALE: NONE SHEET 4 OF 4
8 7 6 5 4 3 2 1
D D
1/2
12.7 mm
100028
C C
3
76.2 mm
1 1/2
38.1 mm
3
76.2 mm
B B
1 1/2
38.1 mm
3/4 X 45_ NAME DATE PROJECT:
19.1 mm DRAWN BEDDINGFIELD
12/18/11
CEB PRESS
CHECKED DESCRIPTION:
1
APPR.
A A
25.4 mm UNLESS OTHERWISE SPECIFIED
DRAWER ASSY ITEM 100028
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
+-.5 +-.1 +-.03 +-.005
LICENSE INFORMATION
SIZE DWG. NO. REV
B
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO: 100028 A
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: PAGE 1 OF 1
8 7 6 5 4 3 2 1
Notes:
1. Drawing prepared in accordance with
ASME Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges. 24 Preferred Wide FW 0.5 12
3. Apply one coat primer in accordance with 23 01-063-00-0 1
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes 22 HBOLT 0.5000-13x1x1-C 4
to be free of primer and paint. 21 HBOLT 0.5000-13x2x1.25-N 2
5. Screws shall be unlubricated and shall be 20 HBOLT 0.7500-10x3x3-C 2
installed using the following torques, 19 HBOLT 0.7500-10x2.5x2.5-C 6
measured above running torque:
Thread Size Torque (Ft-lb) 18 HBOLT 0.5000-13x4x4-C 2
0.250-20 10+/-1 17 HBOLT 0.7500-10x2x2-C 19
0.250-28 8+/-1 16 HBOLT 0.7500-10x1.5x1.5-N 6
0.375-16 35+/-4 15 HNUT 0.5000-13-D-C 8
0.375-24 28+/-3 14 hex nut_ai 31
0.500-13 86+/-9
0.500-20 70+/-7 13 01-059-00-0 1
12 01-051-00-0 1
35 01-102-00-0 2 11 01-050-00-0 2
34 01-098-00-0 1 10 01-076-00-0 1
33 01-119-00-0 1 9 01-026-00-0 1
32 01-092-00-0 1 8 25TL14-112 1
31 01-091-00-0 1 7 01-018-00-0 1
30 01-084-00-0 1 6 01-019-00-0 1
29 WASHER 0.7500-WIDE 40 5 01-010-00-0 1
28 01-080-00-0 1 4 01-009-00-0 1
27 01-079-00-0 1 3 01-003-00-0 1
26 01-073-00-0 1 2 TS2.5x2.5x0.1875x6 4
25 01-070-00-0 1 1 01-002-00-0 4
ITEM NO. PART NUMBER QTY. ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-001-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 3
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24,
ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757,
and two coats lusterless enamel in accordance with TT-E-
52T. Threads and holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed using
the following torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7 1
3 HBOLT 0.7500-10x1.5x1.5-N 1
2 01-006-00-0 1
1 01-005-00-0 1
ITEM NO. PART NUMBER Default/QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-002-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with
ASME Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes
to be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques,
measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 4X 1 2 01-004-00-0 1
1 01-005-00-0 4
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-003-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 3
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-004-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above
running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1 2 1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 hex nut_ai 1
1 TS2.5x2.5x0.1875x6 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-005-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-006-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-009-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-010-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-011-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-012-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes
to be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7 3 2X
2
1
3 hex nut_ai 2
2 01-012-00-0 1
1 01-011-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-013-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-014-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-015-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-017-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to
be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2
1
2 01-003-00-0 1
1 01-017-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-018-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME y14.5,
and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and two
coats lusterless enamel in accordance with TT-E-52T. Threads and 20WASHER 0.7500-WIDE 34
holes to be free of primer and paint. 19HBOLT 0.7500-10x2x2-C 34
5. Screws shall be unlubricated and shall be installed using the 18HBOLT 0.7500-10x3x3-C 4
following torques, measured above running torque:
Thread Size Torque (Ft-lb) 17hex nut_ai 45
0.250-20 10+/-1 16HNUT 0.5000-13-D-C 2
0.250-28 8+/-1 15Preferred Wide FW 0.5 2
0.375-16 35+/-4 B18.2.4.1M - Hex nut, Style 1,
0.375-24 28+/-3 14 M12 x 1.75 --D-C 4
0.500-13 86+/-9
0.500-20 70+/-7 13 B18.22M - Plain washer, 12 4
mm, narrow
12 01-121-00-0 1
11 01-055-00-0 1
10 01-038-00-0 1
9 01-039-00-0 1
29 01-097-00-0 1 B18.2.3.5M - Hex bolt M12 x
28 01-117-00-0 2 8 1.75 x 55 --30N 4
27 01-113-00-0 2 7 RM3-2RS 4
26 01-110-00-0 2 6 01-021-00-0 2
25 01-103-00-0 1 5 01-114-00-0 1
24 01-095-00-0 3 4 01-116-00-0 1
23 01-094-00-0 1 3 01-014-00-0 1
22 01-101-00-0 2 2 01-016-00-0 1
21 01-107-00-0 2 1 01-013-00-0 2
ITEM NO. PART NUMBER QTY. ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-019-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 3
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24,
ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757,
and two coats lusterless enamel in accordance with TT-E-
52T. Threads and holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above running
torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
1
2 HBOLT 0.5000-13x2x1.25-N 1
1 01-020-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-021-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-022-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-023-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-024-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-025-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME
y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and
two coats lusterless enamel in accordance with TT-E-52T.
Threads and holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed using the
following torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
9 01-032-00-0 1
8 01-031-00-0 1
7 01-030-00-0 2
6 01-029-00-0 1
5 01-028-00-0 1
4 01-025-00-0 1
3 01-024-00-0 1
2 01-023-00-0 2
1 01-022-00-0 2
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-026-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 2
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-028-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-029-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-030-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-031-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-032-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-034-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-035-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-036-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-037-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-
P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to
be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9 2X 2
0.500-20 70+/-7
1
2 01-037-00-0 2
1 01-036-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-038-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to
be free of primer and paint. 4 2
5. Screws shall be unlubricated and shall be 1
installed using the following torques, measured A
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
B
3 2X
5 01-120-00-0 1
5 4 hex nut_ai 1
3 01-040-00-0 2
B 2 01-035-00-0 1
1 PMC-21012 1
SECTION B-B SECTION A-A
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-039-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-041-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-042-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-043-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-044-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-045-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-046-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-047-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME y14.5, and
ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and two coats
lusterless enamel in accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed using the following
torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
6 01-106-00-0 2
5 01-105-00-0 2
4 01-074-00-0 1
3 01-047-00-0 2
2 01-043-00-0 1
1 01-042-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-048-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 2
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-049-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME y14.5, and
ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and two coats
lusterless enamel in accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed using the following
torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9 1
0.500-20 70+/-7
2 2X
2 HBOLT 0.7500-10x1.5x1.5-N 2
1 01-049-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-050-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-051-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-055-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24,
ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and
two coats lusterless enamel in accordance with TT-E-52T.
Threads and holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed using
the following torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2X 2 2X 1
2 01-058-00-0 2
1 01-057-00-0 2
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-059-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-060-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-061-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-062-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME
y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and two
coats lusterless enamel in accordance with TT-E-52T. Threads and
holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed using the
following torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
10 HNUT 0.5000-13-D-C 12
9 Preferred Wide FW 0.5 12
8 HBOLT 0.5000-13x1x1-C 12
7 01-067-00-0 12
6 01-066-00-0 12
5 01-064-00-0 4
4 01-065-00-0 4
3 01-061-00-0 1
2 01-062-00-0 2
1 01-060-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-063-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 2
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-064-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-065-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-066-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-067-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-068-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-069-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
6 01-118-00-0 1
5 hex nut_ai 2
4 01-071-00-0 33
3 01-086-00-0 1
2 01-069-00-0 2
1 01-068-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-070-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 2
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-071-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-073-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-074-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME
y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and
two coats lusterless enamel in accordance with TT-E-52T. 18 01-085-00-0 1
Threads and holes to be free of primer and paint. 17 WASHER 0.375-WIDE 8
5. Screws shall be unlubricated and shall be installed using the
following torques, measured above running torque: 16 01-078-00-0 2
Thread Size Torque (Ft-lb) 15 HNUT 0.2500-20-D-C 1
0.250-20 10+/-1
0.250-28 8+/-1 14 HNUT 0.3750-16-D-C 4
0.375-16 35+/-4 13 HNUT 0.5000-13-D-C 2
0.375-24 28+/-3
0.500-13 86+/-9 12 Preferred Wide FW 0.5 2
0.500-20 70+/-7 11 HBOLT 0.2500-20x2x2-C 1
10 HBOLT 0.3750-16x2x2-C 4
9 HBOLT 0.5000-13x2x1.25-N 2
8 Control Valve - 0.5NPTF 1
7 SS-8-RB-4 1
6 SS-8-T_3 1
5 Male Hex Nipple, NPT_SS-8-HN_1_2 2
4 SS-4-SAE-7_4 1
3 01-077-00-0 1
2 BMPH50H2KP 1
1 01-048-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-076-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 2
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above
running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3 3
0.500-13 86+/-9
0.500-20 70+/-7
2
1
3 01-046-00-0 1
2 01-045-00-0 1
1 01-044-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-077-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-078-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-079-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-080-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-081-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-082-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-083-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-
P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to
be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1 1 3 2
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
3 01-082-00-0 1
2 01-081-00-0 1
1 01-083-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-084-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-085-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-086-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-091-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-092-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-093-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above
running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 TROD 0.7500-1x1.25 1
2 1
1 01-093-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-094-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-096-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-
P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to
be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb) 2
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 01-096-00-0 1
1 TROD 0.7500-1x3.5 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-097-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in 2
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above
running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1 1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 01-099-00-0 1
1 TROD 0.7500-1x3.5 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-098-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with
ASME Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes
to be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques,
measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4 3
0.375-24 28+/-3 1
0.500-13 86+/-9
0.500-20 70+/-7
2
3 01-108-00-0 1
2 hex nut_ai 1
1 01-100-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-101-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-102-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-108-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-109-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with
ASME Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes
to be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
1 2
2 01-109-00-0 1
1 01-041-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-110-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be installed 2
using the following torques, measured above
running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 01-111-00-0 1
1 01-112-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-113-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in accordance
with TT-E-52T. Threads and holes to be free of primer
and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above running
torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1 1 2 3
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
3 01-034-00-0 1
2 hex nut_ai 1
1 01-015-00-0 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-114-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-115-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with
ASME Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with
TT-P-1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes
to be free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques,
measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1 1 2 3
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
3 01-034-00-0 1
2 hex nut_ai 1
1 01-115-00-0 1
ITEM NO. PART NUMBER QTY.
BOM Table
NAME DATE PROJECT:
DRAWN YYYY/MM/DD
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-116-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24,
ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757,
and two coats lusterless enamel in accordance with TT-
E-52T. Threads and holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed
using the following torques, measured above running
torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2 1
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-117-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-118-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME Y14.24, ASME
y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-1757, and two
coats lusterless enamel in accordance with TT-E-52T. Threads and
holes to be free of primer and paint.
5. Screws shall be unlubricated and shall be installed using the
following torques, measured above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
2
3 2X
5 .313-18 X 8
4 HYVAIR-D05S-2C-12D-35 SOLENOID 2
3 DAMANAD05S033S MOUNTING BRACKET 2
2 DAMAN-AD05S033S VALVE BLOCK 1
5 8X 1 HYVAIR-D05S-2H-12D-35 SOLENOID 1
ITEM NO. PART NUMBER QTY.
NAME DATE PROJECT:
4 2X DRAWN YYYY/MM/DD
1
APPR. YYYY/MM/DD
UNLESS OTHERWISE SPECIFIED Valve Block
Assembly
DIMENSIONS ARE IN INCHES
ANGLES .X .XX .XXX
.5 .1 .03 .005
LICENSE INFORMATION
SIZE DWG. NO. REV
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-119-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-120-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 01-121-00-0
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A 25TL14-112
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A BMPH50H2KP A
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A DAMANAD05SA
ALL INFORMATION IS RELEASED UNDER THE OSE
033S
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A DAMAN-AD05SA033S
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A HYVAIR-D05S-2A
ALL INFORMATION IS RELEASED UNDER THE OSE
C-12
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A HYVAIR-D05S-2A
ALL INFORMATION IS RELEASED UNDER THE OSE
H-12D
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
le, NP
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A PMC-21012
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A RM3-2RS
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A SS-4-SAE-7_4 A
ALL INFORMATION IS RELEASED UNDER THE OSE
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1
Notes:
1. Drawing prepared in accordance with ASME
Y14.24, ASME y14.5, and ASME Y14.100.
2. Remove all burrs and break sharp edges.
3. Apply one coat primer in accordance with TT-P-
1757, and two coats lusterless enamel in
accordance with TT-E-52T. Threads and holes to be
free of primer and paint.
5. Screws shall be unlubricated and shall be
installed using the following torques, measured
above running torque:
Thread Size Torque (Ft-lb)
0.250-20 10+/-1
0.250-28 8+/-1
0.375-16 35+/-4
0.375-24 28+/-3
0.500-13 86+/-9
0.500-20 70+/-7
A
ALL INFORMATION IS RELEASED UNDER THE OSE
A SS-8-T_3
LICENSE FOR DISTRIBUTIVE ECONOMICS. FOR
FURTHER INFORMATION GO TO:
OPENSOURCEECOLOGY.ORG/WIKI/LICENSE
THIRD ANGLE PROJECTION SCALE: NONE WEIGHT: XX.XLBS SHEET 1 OF 1
5 4 3 2 1