Engine Control System (4HK1) 14-237
DTC U0073 (Flash Code 84)
Control Module Communication Bus Off
Circuit Description
The ECM, the variable nozzle turbocharger (VNT)
control module, the electnc nyaraullc control unit
(EHCU), the transmission control module (TCM), the
data recording module (ORM) and instrument panel
(IP) cluster communicate control and diagnostic
information via a controller area network (CAN)
communication bus. The ECM monitors CAN
operational status by expecting @ constant flow of
messages from each module. if the ECM sets CAN Bus
OFF status, this DTC will set
Condition for Running the DTC
+ The battery voltage is more than 20 volts.
+ The ignition switch is ON.
Condition for Setting the DTC
+ The ECM detects the CAN Bus OFF status.
Circuit/ System Testing DTC U0073 (Flash Code 84)
Action Taken When the DTC Sets.
+ The ECM illuminates the MIL. when the diagnostic
runs and fails. Refer to DTC Type Definitions for
Action Taken When the DTC Sets - Type A.
+ The ECM blinks the exhaust brake Indicator lamp
when the diagnostic runs and fails
+ The ECM limits fue! injection quantity
+ The ECM inhibits exhaust brake control
Condition for Clearing the DTC
+ Refer to DTC Type Definitions for Condition for
Clearing the MIL/ DTC - Type A.
Diagnostic Aids
+ IF an intermittent condition is suspected, refer to
Intermittent Conditions in this section,
+ Parallel resistance of the 1200 resistor in the ECM
land the IP cluster should be 600.
Connector End View Reference: Engine Controls
‘Connector End Views or ECM Connector End Views,
Sep ‘tion Valuots) Yes No.
Did you perform the Diagnostic System Check = Go to Diagnostic
1 | Engine Controls? - ‘System Check =
Goto Step? Engine Controls
1. _tnatalra scan tool
2. ‘Turm OFF the ignition for 30 seconds,
2 | 3. Starthe engine, -
4. Monitor the OTC Information with a scan too.
Go to Diagnostic
oes the DTC fail this ignition? Goto Step3 ‘ids
1. Tum OFF the ignition.
2. Disconnect the variable nozzle turbocharger
(VNT) control module J247 hamess
% ‘connector, _
3. Tum ON the ignition, withthe engine OFF.
4. Monit the ITC Information with a scan tol
Is DTC UOt10 set, but not DTC W007? Goto Step 10 Goto Step 4
Notice: [Fro ABS is installed, sip to Stop 5.
1. Tum OFF the ignition.
2, Reconnect the VNT control module J247
hamess connector if disconnected,
4 | 3. Disconnect the electric hydraulic control unit es
(EHCU) 122 hamess connector.
4. Tum ON the ignition, withthe engine OFF
5. Monitor he DTC Information with a sean tol
Is DTC U0073 sat? Goto Step 5 Goto Step 111-238 _Engine Control System (4HK1)
Sep ‘Action valvots) Yes Ro.
Wotice: if no Smoother tanemission i install
skip to Stop 6.
1, Tum OFF the ignition.
2. Reconnect the VNT control module J247
hhamoze conncetor If dsoonnected,
3. Reconnect the EHCU J22 hamess connector
5 if disconnected. =
4, Disconnect the transmission control module
(TCM) 8112 namess connector
5, Tum ON the ignition, withthe engine OFF.
6. Monitor the DTC Information with a scan tol
Is DTC PO101 sot, but not DTC U0073? Goto Step 13 Goto Step 6
1._Tum OFF the ignition.
2. Reconnect the VNT control module J247
‘harness connector if disconnected,
3. Reconnect the EHCU J22 hemess connector
If disconnected.
4, Reconnect the TEM 8112 hamess connector
6 ‘faiscannected, -
‘5. Disconnect the data recording module (ORM)
231 hamess connector.
6. Tum ON the ignition, withthe engine OFF.
7. Monitor the DTC Information with a scan tol
Is DTC U0073 sot? Goto Step7 Goto Step 12
1. Tum OFF the ignition
2. Reconnect the DRM 8231 hamess connector
‘disconnected.
3, Remove the bezel surrounding the instrument
‘panel (IP) cluster enough to remove the IP
s cluster. _
4. Disconnect the IP cluster 8105 hamess
‘connector
'5, Tur ON the ignition, withthe engine OFF
6. Monit the DTC Information with a sean tol
Is DTC U0073 set? Goto Step8 Goto Siep 9
1. Test the CAN Low and High arcu among
each control_module for the following
‘conditions:
+ Ahor cirout eacn other
8 +A shor to ground -
+ Ashor to battery or ignition voltage
2. Repair the cieuit(s) as necessary.
Did you find and eorrect the condition? Goto Step 15 Goto Stop 14
Roplace the IP clusier. Refer o Instrument Panel
(IP) Cluster in Section 9 Instrumentation’ Driver
9 | inte =
Did you complete the replacement? Goto Step 15 -
Roplace the VNT contol module. Refer t VNT
40. | Control Module in Section 1d induction. -
Did you complete the replacement? Goto Step 15, =Engine Control System (4HK1) 14-239
Step) ‘Action Vvaluots) Yes No
Important Replacement EHCU must be
programmed.
41 | Replace the EHCU. Refer fo EHCU in Section Act _
ABS) ASR,
Did you curmplats Une vopiacorett? Gow sup 19 -
Replace the DRM,
7 -
Did you complete the replacement? Goto Step 15, -
Important Replacement TCM must be
programmed and leamed.
43. | Replece the TOM, Refer to TOM in Secton 5A, _
‘Transmission Control System
Did you compte the roplacomant? Goto Stop 15 =
Important: Replacement ECM musi be
programmed and leamed,
14 | Replace the ECM Refer to ECM Replacement, =
Did you complete the replacement? Goto Step 15 =
1. Reconnect all previously disconnected
‘components or hamess connector(s.
2. Clear the DTCs with a scan tool.
3. Tum OFF the ignition for 30 seconds.
4. Star the engine
18 | 5. Operate the vehicle within the Conditions for =
Running the DTC, You may also operate the
vehicle within the conditions that you
‘observed ‘rom the Freeze Frame! Failure
Records,
Did the OTC fal this ignition? Goto Step Goo Step 16
‘Observe the DTG information with a scan tool.
6 -
‘Are there any DTCs that you have not diagnosed? Goto DTC List System OK