Professional Documents
Culture Documents
Version 7.4
Legal Notices
This guide is copyrighted ©2007 by Digidesign, a division of
Avid Technology, Inc. (hereafter “Digidesign”), with all rights
reserved. Under copyright laws, this guide may not be
duplicated in whole or in part without the written consent of
Digidesign.
003, 003 Rack, 96 I/O, 96i I/O, 192 Digital I/O, 192 I/O,
888|24 I/O, 882|20 I/O, 1622 I/O, 24-Bit ADAT Bridge I/O,
AudioSuite, Avid, Avid DNA, Avid Mojo, Avid Unity, Avid Unity
ISIS, Avid Unity MediaNetwork, Avid Xpress, AVoption,
AVoption|V10, Beat Detective, Bruno, Command|8, Control|24,
D-Command, D-Control, D-Fi, D-fx, D-Show, DAE, Digi 002,
Digi 002 Rack, DigiBase, DigiDelivery, Digidesign, Digidesign
Audio Engine, Digidesign Intelligent Noise Reduction,
Digidesign TDM Bus, DigiDrive, DigiRack, DigiTest,
DigiTranslator, DINR, DV Toolkit, EditPack, Impact, Interplay,
M-Audio, MachineControl, Maxim, Mbox, MediaComposer,
MIDI I/O, MIX, MultiShell, OMF, OMF Interchange, PRE,
ProControl, Pro Tools M-Powered, Pro Tools, Pro Tools|HD,
Pro Tools LE, QuickPunch, Reel Tape, Reso, Reverb One,
ReVibe, RTAS, Smack!, SoundReplacer, Sound Designer II,
Strike, Structure, SYNC HD, SYNC I/O, Synchronic, TL Space,
Velvet, and X-Form are trademarks or registered trademarks of
Digidesign and/or Avid Technology, Inc. All other trademarks
are the property of their respective owners.
Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Contents iii
iv Upgrading to Pro Tools 7.4
chapter 1
Introduction
Compatibility Information
If you are configuring a new Pro Tools sys-
Digidesign can only assure compatibility and
tem, follow the complete hardware and soft-
provide support for hardware and software it
ware installation steps in the Getting Started
has tested and approved.
Guide that came with your system.
For a list of Digidesign-qualified computers, op-
erating systems, hard drives, and third-party de-
vices, refer to the latest compatibility informa-
tion on the Digidesign website
(www.digidesign.com).
Internet Access
Upgrading to any version of Pro Tools requires
access to the Internet for software activation
and registration purposes.
DVD Drive
The Pro Tools Installer disc requires a DVD drive
for installation.
Chapter 1: Introduction 1
2 Upgrading to Pro Tools 7.4
chapter 2
8 Select the Pro Tools application for installa- Preference settings can be customized at any
tion. time in Pro Tools. See the Pro Tools Refer-
ence Guide for more information.
12 Click Next.
AFL/PFL Solo modes require the Surround 2 Uninstall your older version of Pro Tools. See
Mixer plug-in. See the Pro Tools Reference “Uninstalling Pro Tools” on page 14.
Guide for more information.
3 Do one of the following:
14 Click Next. • Insert the Pro Tools Installer disc for Win-
dows in your DVD drive. Locate and open
15 Click Install.
the Pro Tools Installer folder, and double-
On Windows XP, several messages are dis- click the Setup icon.
played during installation that can be ig- – or –
nored, including multiple “Found New • If you downloaded the Pro Tools Update
Hardware” dialogs and “A Problem Oc- from our website, follow the instructions
curred During Hardware Installation.” provided with it to expand and launch the
installer.
Additionally, if you get a warning dialog
about the driver not passing Windows Logo 4 Follow the on-screen instructions to proceed
testing, click Continue Anyway. with installation.
Command|8 Controller and Driver The Com- To install Pro Tools M-Powered:
mand|8 Driver is required if you are using the 1 Start Windows, logging in with Administrator
Digidesign Command|8 control surface. privileges. For details on Administrator privi-
leges, refer to your Windows documentation.
MP3 Export Option The MP3 Export Option lets
you export MP3 files from Pro Tools. This op- 2 Uninstall your older version of Pro Tools. See
tion is purchased separately. “Uninstalling Pro Tools” on page 14.
10 Click Install.
• Insert the Pro Tools Installer disc for Win-
dows in your DVD drive. Locate and open
On Windows XP, several messages are dis- the Pro Tools Installer folder, and double-
played during installation that can be ig- click the Setup icon.
nored, including multiple “Found New – or –
Hardware” dialogs and “A Problem Oc-
• If you downloaded the Pro Tools Update
curred During Hardware Installation.”
from our website, follow the instructions
Additionally, if you get a warning dialog provided with it to expand and launch the
about the driver not passing Windows Logo installer.
testing, click Continue Anyway. 4 Follow the on-screen instructions to proceed
with installation.
On Windows Vista, if you get a Windows 5 Select the install location. For maximum reli-
Security dialog asking you to install device ability, install Pro Tools on your startup drive.
software, click “Install”
6 Click Next.
11 Wait for the installer to finish installing all
7 Select the Pro Tools application for installa-
software components, drivers, and PACE System
tion.
files before proceeding to the next step.
8 You can also select from a list of optional
12 When installation is complete, click Finish.
items to install along with Pro Tools.
13 Proceed to “Installing QuickTime” on page 8.
DigiTranslator DigiTranslator™ is a software op-
tion for Pro Tools that lets you convert and ex-
change OMF and AAF sequences and MXF files
directly in the Pro Tools application. This op-
tion is purchased separately.
On Windows XP, several messages are dis- For information on which version of Quick-
played during installation that can be ig- Time is compatible with your version of
nored, including multiple “Found New Pro Tools, visit the compatibility pages of
Hardware” dialogs and “A Problem Oc- the Digidesign website
curred During Hardware Installation.” (www.digidesign.com).
Additionally, if you get a warning dialog To install QuickTime:
about the driver not passing Windows Logo
testing, click Continue Anyway. 1 Visit www.apple.com and go to the Quick-
Time page.
On Windows Vista, if you get a Windows 2 Download the QuickTime installer applica-
Security dialog asking you to install device tion to your computer.
software, click “Install” 3 Double-click the QuickTime installer applica-
tion and follow the on-screen installation in-
11 Wait for the installer to finish installing all
structions.
software components, drivers, and PACE System
files before proceeding to the next step. 4 Restart your computer.
12 When installation is complete, click Finish. If the USB LED on the front panel of the
13 Proceed to “Installing QuickTime” on page 8. Mbox 2 does not illuminate after installa-
tion, try unplugging the USB cable from the
Mbox 2 USB port, and plugging it back in.
If the USB LED still does not illuminate,
shut down the computer, disconnect
Mbox 2 and start the computer. Once the
computer has fully restarted, reconnect
Mbox 2.
• Locate and double-click the Pro Tools HD If you get a warning dialog about updating
application on your hard drive. the firmware for your hardware, follow the
on-screen instructions to perform the
Do not remove the iLok during Pro Tools
firmware update. “Updating 003 or
launch or use.
003 Rack Firmware” on page 10
5 When prompted, select your audio drive as To install factory session templates:
the install location and click Next to begin the
1 Insert the Pro Tools Installer disc into your
install.
DVD drive.
6 When installation is complete, click Finish.
2 From your DVD drive, locate and open Addi-
tional Files and then the Session Templates In-
staller folder for your system.
4 Click Uninstall.
Installing Pro Tools HD MIDI I/O Driver The MIDI I/O Driver is required
if you are using the Digidesign MIDI I/O.
To install Pro Tools HD software:
MP3 Export Option The MP3 Export Option lets
1 Make sure you are logged in as an Administra- you export MP3 files from Pro Tools. This op-
tor for the account where you want to install tion is purchased separately.
Pro Tools. For details on Administrator privi-
7 Click Install.
leges in Mac OS X, refer to your Apple OS X doc-
umentation. 8 If prompted, enter your Administrator pass-
word and click OK to accept the installation.
2 Do one of the following:
• Insert the Pro Tools Installer disc in your 9 Select your work environment. This loads an
DVD drive. Double-click “Install initial set of Pro Tools Preferences that include
Pro Tools.” some of the more popular settings for post pro-
duction, audio, or audio with MIDI.
– or –
• If you downloaded the Pro Tools Update Preference settings can be customized at any
from our website, follow the instructions time in Pro Tools. See the Pro Tools Refer-
provided with it to expand and launch the ence Guide for more information.
installer.
10 Select whether to install the Surround Mixer
3 Select the install location. For maximum reli-
plug-in. This plug-in is required for mixing,
ability, install Pro Tools on your startup drive.
mastering, and monitoring in surround:
4 Click Continue. • Select “Yes – Monitoring in Standard
Pro Tools (Film Format)” if your monitor-
5 Select the Pro Tools application for installa-
ing is configured for Film Format surround.
tion.
• Select “Yes – Monitoring in ProControl
6 You can also select from a list of optional (DTS Format)” if you are using a ProCon-
items to install along with Pro Tools: trol dedicated controller.
Avid Video Engine The Avid Video Engine is re- • Select “No – Stereo mixing only” if your
quired to use Pro Tools with Avid video periph- monitoring is configured for Stereo.
erals such as the Avid Mojo or the Digidesign
AFL/PFL Solo modes require the Surround
AVoption|V10.
Mixer plug-in. See the Pro Tools Reference
DigiTranslator DigiTranslator™ is a software op- Guide for more information.
tion for Pro Tools that lets you convert and ex-
11 Click Continue.
change OMF and AAF sequences and MXF files
directly in the Pro Tools application. This op-
tion is purchased separately.
To use Pro Tools HD, you must always have an To install Pro Tools LE on Mac OS X:
inserted iLok with an authorization for
1 Make sure you are logged in as an Administra-
Pro Tools HD. One pre-authorized iLok is in-
tor for the account where you want to install
cluded with your Pro Tools HD system.
Pro Tools. For details on Administrator privi-
leges in Mac OS X, refer to your Apple Mac OS X
To authorize Pro Tools HD software: documentation.
1 Insert the pre-authorized iLok into an avail-
2 Do one of the following:
able USB port on your computer.
• Insert the Pro Tools Installer disc in your
2 Do one of the following: DVD drive. Double-click “Install
• Click the Pro Tools HD icon in the Dock. Pro Tools.”
– or – – or –
• Locate and double-click the Pro Tools HD • If you downloaded the Pro Tools Update
application on your hard drive. from our website, follow the instructions
provided with it to expand and launch the
Do not remove the iLok during Pro Tools installer.
launch or use.
3 Follow the on-screen instructions to continue
and accept installation.
5 Click Continue.
8 Click Install.
Installing Pro Tools M-Powered
9 If prompted, enter your Administrator pass-
word and click OK to authenticate the installa- To install Pro Tools M-Powered:
tion.
1 Make sure you are logged in as an Administra-
10 Follow the remaining on-screen instructions. tor for the account where you want to install
11 When installation is complete, click Restart. Pro Tools. For details on Administrator privi-
leges in Mac OS X, refer to your Apple Mac OS X
The Pro Tools Installer disc includes addi- documentation.
tional software for your system. For more in-
2 Do one of the following:
formation, see “Additional Software on the
• Insert the Pro Tools Installer disc in your
Pro Tools Installer Disc” on page 20.
DVD drive. Double-click “Install
Pro Tools.”
Launching Pro Tools LE
– or –
When launching Pro Tools LE the first time, you
• If you downloaded the Pro Tools Update
are prompted to enter an authorization code to
from our website, follow the instructions
validate your software.
provided with it to expand and launch the
installer.
To authorize Pro Tools LE software:
3 Follow the on-screen instructions to proceed
1 Make sure your LE interface is connected to
with installation.
your computer and powered on if it has a power
switch. 4 Select the install location. For maximum reli-
ability, install Pro Tools on your startup drive.
2 Click the Pro Tools LE icon in the Dock (or
double-click the application icon in the 5 Click Continue.
Pro Tools folder inside the Digidesign folder).
6 Select the Pro Tools application for installa-
tion.
The Digidesign CoreAudio Driver for your For information on configuring the Mbox 2
Digidesign hardware is automatically installed CoreAudio Driver, see the CoreAudio Driv-
when you install Pro Tools. ers Guide.
For information on installing and configur- See the Pro Tools Reference Guide for informa-
ing the standalone version of the Digidesign tion on using or customizing session templates.
CoreAudio Driver, see the CoreAudio Driv-
ers Guide. To install factory session templates:
1 Insert the Pro Tools Installer disc into your
Pro Tools Demo Session DVD drive.
The Pro Tools Installer disc includes a demo ses- 2 From your DVD drive, locate and open Addi-
sion that you can use to verify that your system tional Files and then the Session Templates In-
is working. staller folder for your system.
2 From your DVD drive, locate and open the Ad- 5 When prompted, select your audio drive as
ditional Files\Pro Tools Demo Session Installer the install location and click Next to begin the
folder. install.
3 Double-click the Setup.exe for your system’s 6 When installation is complete, click Close.
demo session.
2 Go to Applications/Digidesign/Pro Tools/
Pro Tools Utilities and double-click the
“Uninstall Pro Tools” file.
5 Click Uninstall.