Course Name : AUTOMOBILE Exam Sesssion 2020 SEM:5TH SEM
S.No QUESTIONS OPTION A OPTION B OPTION C OPTION D Correct Ans
1 The source of power of a automobile engine battery fuel none A The part used to supports the engine wheels body 2 frame battery chasis both a & b D breaking system steering etc is known as The purpose of the ___________ is to allow to couple or 3 break clutch gear steering B decouple the engine & transmission 4 Which engine require an ignition system diesel engine steam engine petrol engine none C 5 The inner diameter of cyclinder known as TDC BDC Bore stroke C 6 Which device atomises the fuel & mixes it with air compressor condenser carburetor ignitor C 7 The factor affecting carburation the engine speed engine design the design of carburator both a & b D 8 In IC engine fuel injected in to the cyclinder at the end of suction stroke expansion stroke power stroke compression stroke D 9 Injection of fuel directly in to combustion cham,ber is known common as rail injection solid injection air injection none B 10 The petrol between the start of injection & start of ignition isignition known delay as injection delay pum ping delay none A combustion is a chemical combination of hydrogen & 11 argon nitogen oxygen CO2 A carbon in fuel with 12 The combustion gives an energy in the form of pressure force displacement heat D 13 Effect of detonation? noise & roughness mechanical damage both a &b none C 14 How the detonation effect the carbon deposite in engine? increases decreases same none A 15 Which are the factors effecting knocking? temeperature factors density factos time factor all of the above D buring of oil film 16 Their any damage to engine cooling system which result in between the pure ignition both a & b none C moving part 17 The melting point of platinum 1750 degree celsius 1530 degree celsius 657 degree celsius none A 18 The melting point of iron 1750 degree celsius 1530 degree celsius 657 degree celsius none B The two stroke engine which complete a power cycle 19 2 1 3 4 A with in_________stroke? The process of clearing the cyclinder after the expansion 20 compression stroke expansion process scavenging process working stroke C stroke is known as 21 Volume of a four stroke cycle engine can be replaced by delivery ratio charging efficiency both a & b none C 22 Super charger is an air ______________ device purification filter compression none C raise the decrease volumetric 23 The purpose of super charging volumetric maintain volumetric efficiency all of the above A efficiency efficiency 24 Which are the types of super charger van blower LY sholm compressor both a& b none C 25 A turbo charger utilize a portion of energy contained in__________?intake gas exhaust gas fuuel piston B 26 Which are the performance parameter specific fuel consumption break mean effective pressure specific weight all of the above D 27 The equation used to find break power is 60/2piNT 2piNT/60 NT/60 2pi60/NT B 28 The torque measuring device is known as dynamometer ceroks crew velocity meter potentiometer A 29 Expression for mechanical efficiency ip/bp ipxbp ip-bp bp/ip D 30 Break power per unit of piston displacement is known as specific output specific input both a & b none A The part reciprocates in the cyclinder under action of 31 cyclinder head crank shaft valves piston D hot gas? The maximum distance travel by the piston in single 32 bore swept stroke none C direction is known as 33 Which part is used to mix the petrol & air spark plug fuel pump fly wheel carborator D If a force applied on some point to cause turning effect 34 pressure force torque none C is called_____________ 35 The pipe carries the prepared mixture to engine fuel pipe intake manifold outlet manifold none B The process of preparing in the SI engine ,a combustible 36 condensation carburation mixing all of the above B fuel air mixture outside the engine cylinder What is the stoichiometric fuel air ratio for 37 01:15 01:05 01:10 01:50 A hydrocarbons 38 Knocking is due to auto ignition over speed design of engine none A 39 Which is the cooling systems used in automobile air cooling system water cooling system oil cooling system all of the above D 40 The sector effecting flame propogation air fuel ratio compression ratio load on engine all of the above D 41 Which are the parts of liquid cooling system water pump fan radiator all of the above D 42 The function of lubrication reduces friction effect act as fuel used in breaking system none A Crank angle during which both inlet & exhaust port are 43 scavenging angle angles of operation both a & b none A open The method utilized to increase the air consumption of increase the decrease the density of 44 running engine in lower speed none A air pitondisphcoment the charge provide better 45 Which sre function of super charger mixing of air-fud to increase the power output both a & b none C mixture 46 Which part of engine operates the valve at engine crank comshaft piston ECU B i) exhaust stroke i) suction stroke i) suction stroke ii) working stroke ii)compression ii)combustion stroke Which is the correct order of cycle for fore stroke iii) compression stroke 47 stroke iii) iii) compression none A engine iv) section stroke working stroke stroke iv)exhaust stroke iv) working stroke 48 The range of useful air fuel ration for SI Engine 8:1 to 12:1 20:1 to 8:1 20:1 to 150:1 none B The property of fuel with discorites how fud will or will 49 flame factor density octane number none C not self ignite Which compant have higher orelutive effectiveness of 50 teture ethyl tin nickel carbonyl methyl cyclo pentadienyltetra ethyl lerd D anti knocks Correct Ans