Professional Documents
Culture Documents
Colour Television Chassis: Block Diagrams, Test Point Overviews, and Waveforms
Colour Television Chassis: Block Diagrams, Test Point Overviews, and Waveforms
SK4.0L
CA
H_17210_000.eps
070607
Contents Page
1. Technical Specifications, Connections, and Chassis
Overview 2
2. Safety Instructions, Warnings, and Notes 4
3. Directions for Use 6
4. Mechanical Instructions 7
5. Service Modes, Error Codes, and Fault Finding 9
6. Block Diagrams, Test Point Overviews, and
Waveforms
Block Diagram Chassis 11
Schematic Overview Chassis 12
7. Circuit Diagrams and PWB Layouts
Mono Carrier: Power Supply (A1) 13 21-22
Mono Carrier: Line Deflection (A2) 14 21-22
Mono Carrier: Frame Deflection (A3) 15 21-22
Mono Carrier: Tuner IF (A4) 16 21-22
Mono Carrier: AV Switch (A5) 17 21-22
Mono Carrier: Audio Amplifier (A6) 19 21-22
Mono Carrier: Tone Control (Optional) (A7) 18 21-22
Mono Carrier: CPU & Decoder (A8) 20 21-22
Keyboard Control Panel (D) 23 24
Main Switch Panel (E) 25 25
Side A/V Panel (G) 26 26
BTSC Panel (G) 27 27
Slim EW Panel (M) 28 28
Sub Woofer Panel (Optional) (Z) 29 30
8. Alignments 31
9. Circuit Descriptions, Abbreviation List, and IC Data
Sheets 36
Abbreviation List 37
IC Data Sheets 38
10. Spare Parts List 53
11. Revision List 56
©
Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by JY 0769 BG CD Customer Service Printed in the Netherlands Subject to modification EN 3122 785 17450
EN 2 1. SK4.0L CA Technical Specifications, Connections, and Chassis Overview
1.1.1 Vision
Ambient conditions:
Aerial - In
- Temperature range (°C) : -5 to +45
- - IEC-type (EU) Coax, 75 ohm D
- Maximum humidity : 90% R.H.
M
D
K
E MAIN SWITCH PANEL
A H_17450_003.eps
210907
Safety regulations require the following during a repair: • In order to prevent damage to ICs and transistors, avoid all
• Connect the set to the Mains/AC Power via an isolation high voltage flashovers. In order to prevent damage to the
transformer (> 800 VA). picture tube, use the method shown in figure “Discharge
• Replace safety components, indicated by the symbol h, picture tube”, to discharge the picture tube. Use a high
only by components identical to the original ones. Any voltage probe and a multi-meter (position VDC). Discharge
other component substitution (other than original type) may until the meter reading is 0 V (after approx. 30 s).
increase risk of fire or electrical shock hazard.
• Wear safety goggles when you replace the CRT.
• All resistor values are in ohms, and the value multiplier is • It makes sense to avoid exposure to electrical shock.
often used to indicate the decimal point location (e.g. 2K2 While some sources are expected to have a possible
indicates 2.2 kohm). dangerous impact, others of quite high potential are of
• Resistor values with no multiplier may be indicated with limited current and are sometimes held in less regard.
either an "E" or an "R" (e.g. 220E or 220R indicates 220 • Always respect voltages. While some may not be
ohm). dangerous in themselves, they can cause unexpected
• All capacitor values are given in micro-farads (μ= x10-6), reactions that are best avoided. Before reaching into a
nano-farads (n= x10-9), or pico-farads (p= x10-12). powered TV set, it is best to test the high voltage insulation.
• Capacitor values may also use the value multiplier as the It is easy to do, and is a good service precaution.
decimal point indication (e.g. 2p2 indicates 2.2 pF).
• An "asterisk" (*) indicates component usage varies. Refer
to the diversity tables for the correct values.
• The correct component values are listed in the Spare Parts
List. Therefore, always check this list when there is any
doubt.
4. Mechanical Instructions
Index of this chapter: 4.2 Assembly / Board Removal
4.1 Set Disassembly
4.2 Assembly / Board Removal
4.2.1 Side I/O Panel removal
4.3 Set Re-assembly
H_17210_025.eps
130607
H_17210_032.eps
110607
H_17210_026.eps
080607
1 1 1
H_17210_027.eps
080607
5.1 Test Points 5.4.7 Picture with Horizontal Bright Line and Sound
See chapter 6 "Block Diagrams, Testpoint Overviews, and Check both supply voltages of vertical IC301 and relevant
Waveforms". circuitry on correctness. Also check the vertical synchronizing
signal from IC201.
Perform measurements under the following conditions:
• Service Default Mode. 5.4.8 Remote Control Malfunction
• Video: colour bar signal.
• Audio: 3 kHz left, 1 kHz right. Check the voltage on pin 64 of IC201. The normal value should
be 5.15 V. If this is correct check front control panels soldering
connections. If can't be solved, check the remote control,
5.2 Service Modes crystal or transmitting diode of the remote control are in good
condition.
This chassis does not contain a specific Service Mode. Service
and Alignment of the TV set can be done via the Factory Mode 5.4.9 No Sound
by the service technician, see further down in this manual.
5.4.1 Power on Failure Check the sound system after searching the channel which
should set at NTSC or AUTO. If still has problem, check
Check whether the power supply is working properly and accompany board circuit on chassis good or not.
whether the values of voltages normal. If those are correct,
check line transistor and transformer are working properly or
check fore or back line for defects.
Personal Notes:
E_06532_012.eps
131004
Block Diagrams, Test Point Overviews, and Waveforms SK4.0L CA 6. EN 11
AUDIO G
Y U V REAR AV SIDE AV S-VHS AV OUT
ANTENNA SCART 1
V in V L R V L R Y C
D V L R D
A7
AMP-TDA9841/9842/9843
V L R
R GB 15 A5
AV2 SW 2 A6 L
AV1 SW AV3 SW SPL
AV-SW 4052
TONE CONTROL
5 13 L
14
1 3 R
4 C in 12 R SPR
CVBS OUT
62 10
63 FM 9
AV in 4 11
FS TUNER
K
SDA
SCL
SCL
C IF MTS/A2/NICAM C
IF IF AMP SAW101 SDA
PHILIPS UOC2
SCL
R
A4 B R OUT
SDA
G
KEY CONTROL TDA93XX/N3
G OUT
B 21" CRT
D 6 KEY B OUT
IK
PWM CONTROL AUDIO VOL 7
MUTE 10 I/O
44
AUDIO OUT
5
CRT BOARD
SCART ID
A8
B B
V--DY
SDA
SCL
POWER A3
+110V FOR B+
V AMP TDA4863AJ
+43V 24C08 H--DY
E
CQ0765
90V-260V
SW
+8V FOR UOC
+12V -12V
+12V FOR MAIN
3DD5023
A1 +20V FOR AMP M H DRIVE
SLIM PART
A A
A2
1 2 3 4 5 6
Block Diagrams, Test Point Overviews, and Waveforms SK4.0L CA 6. EN 12
H_17450_006.eps
210907
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 13
A1 POWER SUPPLY A1
D D
C C
Stand by
B B
A A
H_17450_009.eps
5800 A3P610-00 210907
1 2 3 4
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 14
A2 LINE DEFLECTION A2
EHT
BCL
CN301 EHT BCL
D T0 D
CRT
HEATER
CRT G N D
5
1 80 V
GND
6
1
!
R315 D309
R310
4.7K
560K
1N4148
R318
680
+48V_VCC R317
D305
!
+8V_VCC 220
T301 MTZJ20
R301
3
+V
0.33 +V
C 2W C
R401 T302 R302 4
4K7 -V 7 R316 AFC
0.33 -V AFC
4.7K
Q450 R327 AFC
R325 R319
C2482 2K7 6
H-out D306
100
HEATER C310
3.9K 27PF/ 50V 8V2
!
C321 C322
R403 C323 9
NC 2200pF 220pF
500V 500V 1uF M
160V
5
GND
FOCUS
FOCUS
2 R245
+135V_VCC
10
B+ 1K
180V
SCREEN
470PF 500 V
C309 C300 D308 R314
SCREEN D205
4.7UF 250V 2158 0.22 2W
R321
L432 L302
1K C238
34mH 1N4148
790mH
4.7U/ 50V
C319
B B
681
R323
8 R312 R250
1
75K +8V_VCC
Q302 2.2K
D5032
! HY ABL 1K
Q303 ! C308
D307
R324
F630 ! D302
C318 FLYBACK 0.1U
1N4148
EW
C314 ! C315
7n2
C316 BY228 C325
364J/400
100 ! 2n7 /2KV
2KV
6n8
2KV
274J/400V
C317
R454 L301
33 564 105mH
D311
C312 RU4B
273J/630V
!
R322
6.8 2W
L303 400uH
C477
4.7uF
50V
A A
H_17450_010.eps
5800 A3P610-00 210907
1 2 3 4
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 15
A3 FRAME DEFLECTION A3
D CN301 D
IC301
TDA4863AJ
!
5
Vp3 pump
VP1 +13V
VP4 -13V
6
!
V out
VP3-
I NN
I NP
7
1
100V
C307
C305 0.1uF/100V
C R255 C
VDRA R309
100
100uF/50V
R256 270 1W
VDRB
D304
100
R308 BA158
C216 C215
1K8 C306
CAP CAP R305 R306
1K8 D303
0.1uF/100V 220/2W
BA158
R307
R304 1
2W C302
+8V
v+
470pF
220/1W
D302
B R326 B
10K BA158
D301
C301
EHT 470pF
v-
Q301
C301 C303
R303 C302 0.1uF 1000uF/ 25V
0.1uF
C304
1000uF/ 25V
A A
H_17210_003.eps
5800 A3P610-00 110607
1 2 3 4
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 16
A4 TUNER IF A4
E Q102 E
C1815
10K
LC101 R115
31.9M R114
C204
10K
0.01U
A101 NTSC-M
R113 R116
D C107 D
IF R106
R111 220 2.2K
R108
L101J
1UH
R105 68 10n C109 470
4.7K R213
NC 1.5K 10n C108
R109 100
1.2K 100pF
BT+33V R703
Q103
10K SYSTEM
C703 C1815
GND IC703 SYSTEM
47/50V Q101
UPC574 KSC1674C
R107
C BM+5V 1.2K R110 C
10
SYSTEM 1
SDA SYSTEM1
C109
0.01U R112 SIF SAW102
SCL 10
SIF SAW102
L201
100U/16V
SAS 10UH
100U/16V
C105
R102
C104
15K
+33V_BT
NC +33V_BT
B +8V_VCC B
+8V_VCC
R215 TUNER AGC
AGC TUNER AGC
680 SDA
C103 SDA
10U/16V R101
SCL
38.9MHz 27K SCL
38MHZ
A A
H_17210_004.eps
5800 A3P610-00 110607
1 2 3 4 5
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 17
Personal Notes:
A5 AV SWITCH A5
D D
+8v
CVBS
CVBS
VIDEO OUT 10
VI 20 C1815 R251 C823
10U/16V
1K
R 8 41
VO
4 .7K R 84 0
19 R842
4.7K
VIG 18 D802 D807 Q803 4.7K
75 R802 1815
8V2
VOG 17
75
BL 16
R835 AV1
V/ R 15 AV1
10K
Q804
D834
BG 14 8V2
R837
75
R834 1815
75
RGND 13
NC 12 R836 AV2
AV2
Y/G 11 Q805 10K
D833 1815
NC 10 R836
75
8V2
GGND 9 J743 R837 AV3
OPT 8
10K 10K
U/B 7
1 .5K R 85 5
1 .5K R 85 4
1 .5K R 85 2
L in 6
D832
BGND 5 R731 R835
75 8V2
GND 4 820
C L803 C
LO 3 C717
R in2
L804
10uF
RO 1 C822
C806 C805
CAP ZD701
R701 0.1U
CAP 8V2
47K
P701 21PIN
CVBS/Y
CVBS/Y
BLANK
BLANK
OPTION
OPTION
V / R in
S-VHS V / R in
Y C242
P702 Y / G in
Y C Y / G in
U / B in
10uF U / B in
P701
U R803
75
C IN
YUV C IN
V
AUDIO L out AUDIO R out
C804 C807
10uF 10uF
TONE 26
TONE 7
R847 Q802 R844
Q801
100 100
C1815 C1815
V out R846 R845
750 750
R848 R849
100K
+8V
C777 R831
R830 2.7K
100K
V IN C190 OUT R
10uF OUT L
R825 10U/16V AUDOUT
100K AUDOUT
P701 C772 TONE 28
+8V
L IN
TONE 1
10uF R827
R834 100K
C774 100K TONE 30
IC801
R IN HEF4052
10uF R821
L 1 16 +8V_VCC
R777 R780 R778 ZD706 100K Vdd +8V_VCC
ZD709 ZD711
75 8V2
100K 100K
8V2 8V2 SIDE L 2 15
SIDE AV IN SIDE R
0
+8V
C816 3 1 14
R151 R152 REAR R 4052 3
2 4052 3
300
0
V IN 100 3 1 4052 13
10uF 4 13
R826 2 4052 13
100K
C811 3
L806 R815 REAR L TONE 32
5 12
P701 L IN 1K
C812 10uF R831
D802 R828 1.2K 6 11
1000 8V2 100K E
L805 C810
R816
7 10 R838 A1
R IN 1K Vee A1
C813 10uF
1K
+8V
1000 R818 R817 R807 R839
8 9 A2
100K 100K 75 Vss A2
1K
REAR AV IN
A R822 AUDIO SWITCH A
100K
R832
R833 1.2K
100K
H_17210_005.eps
5800 A3P610-00 070607
1 2 3 4
E_06532_012.eps
131004
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 18
A6 TONE CONTROL A6
A A
WEIGHT TONE
B B
C512 C913
R914
R917
510 1000U 0.01U
100K
CN902
VCC
C R911 C
GND 100K
R916 C910 C?
51K
MUTE1 D901 C909
D902 0.22U
8V2
4148 100U CAP
GND R912
C1815
D D
1K R913
Q902 R917
MUTE2 D903 R904 R909 510
VCC
IC901 C?
100K 100K
4148 7 TFA9800
820 R905 C914 8 4
R
C901 R901 MUTEOUT1
10U 10K 0.22U C908 1 6
1K IN- OUT2
E C902 R902 Q901 0.1U 9 2 WOODER 8OHM
E
L C1815 IN+ SG
10U 10K
R903
3 5
Q902 SVRR PG
C903 51K R903 R920
R907
0.47U 51K 270
1K
C907
F R908
0.22U F
C903 100K R912
47U
510
G G
H_17210_006.eps
5800 A3P610-00 110607
1 2 3 4 5 6 7 8 9 10
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 19
A7 AUDIO AMPLIFIER A7
D D
+8V_VCC IC402
+8V_VCC
2 4 6 8 TFA9842AJ
D401 IN4148 1 3 5 7 9
C432 RI RO L in L out
C 100uF R410 C
R411 Q402 75K
A1015 C429 SPL
47K C428 220uF/25V
47uF/ 50V C433 CN760
1000uF/ 25V Lout 4 10W
1 1
SW2
MUTE
MUTE
D761 R409
3K3 Q401 C434
2 2
SPR
C1815 1000UF/ 25V Rout SW2
1N4148
R407 4 10W
10K
R408
VOL R253 3K3
VOL
15K
C431 C430
10uF/ 16V 1uF
B 50V B
C750 R770 1K
4052 13
R OUT 1uF
4050 3
L OUT C749 R769 1K
C426
1uF C424
106E 222D
+22V_VCC
+22V_VCC
A A
H_17210_007.eps
5800 A3P610-00 110607
1 2 3 4
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 20
D D
+5v
5
C227 C203
PT C
V dd
SCL
SD A
0.01U
3 .3K R21 0
3 .3K R20 3
R2 07 3.3 k
47uF/ 16V
3 .3K R20 5
IC202
3.3K R 20 2
3 .3 K R208
C202 C201
24C08
100pF 100pF
3
1
2
GN D 4
IR 5
V ss
n .c.
WP
A2
K EY
LED
5V
1
R234 R235
IC201 R220
3.3K 3.3K +5V_VCC
+5V_VCC
TDA83731 5K1
R217
STANDBY 1 64
STANDBY STANDBY IRin
R204 100 100
SCL 2 63
SCL SCL AV2 A2
R206
SDA 3 62
SDA SDA AV1 A1
100 +3.3V
4 61 L202
MUTE AV3/TUNING VddP 10uH
MUTE
5 60
AV3 SCART ID RESET + L204
AV3 C232
R219 47 C230 10uH L203
6 59 33pF C231 2.2U/ 50V
KEY XTAL OUT X201 0.01U 10uH
7 58 12MHz
VOL VOL VOL XTAL IN
C250 +8V
C226 C205 33pF C229
+
8 57 C233
0.01U MUTE OscGnd C235 0.01u
+3.3V R218 100U/ 10V D206
0.01U 10u/16v
+3.3v 8V2
10K 9 56
C Vss C/P VddC C
C236
10 55 0.01u C234 R243 R725 R425
LED VpE
R312
11 54
10u/16v 22K R247
27K ZD104 D203 D202 D204
PAL PAL/NTSC VddA 33K
10K
8V2 8V2 8V2 8V2 GND
3K3
12 53 R239 100 1
NTSC VssA B OUT B
C207
13 52
R241
100 2
SYSTEM 0.22UF
SECPLL G OUT G
SYSTEM
+8V
L201 10uH 14
Vp2 R OUT
51 R240
100 3
R
CN102
C212 C206
10UH C210 220nF 15 50 R242 10K 4
0.01U 10U/16V
DECDIG BLANKING BL
C208 4n7 C209 2200p 16
PH2LF BCL IN
49 5 BCL
BCL
C211 R245 U / B in
17 48 C239 0.022U
PH1LF B / U IN U / B in
+
15K
C218 C217
1uF/50V
18 47 C240 0.022U Y / G in
1U/ 50V
+ GND3 G / Y IN Y / G in
0.1U
19 46 C241 0.022U
V / R in
C214
DECBG R / V IN V / R in
EW 2.2U/ 50V 20 45 BLANK
EW AVL/EWD BLANK BLANK
VDRB 21 44 AUDIO OUT
VDRB VDRB AUDOUT/AMOUT AUDIO OUT
VDRA 22 43 C IN
VDRA VDRA C IN C IN
IF SAW101 1 4 23 42 CVBS/Y IN
IF IF1 CVBS/Y IN CVBS/Y IN
2 5 24 41
IF2 GND1
R214
25 40
SAW101 IREF CVBSINT
39K
8V
3
SW02B L205
C213 26 39
VSC Vp1 8v
0.1U/ 63V
AGC R231 C244
10uH + C245
27 38 C243
AGC TUNER AGC IFVO/SVO 10U/16V
C219 2.2K R220
R229 0.01U 100U/ 16V
SIF 1 4 0.022U 28 37 C246 100K
SIF AUDEEM/SIF1 PLL IF
390 0.1U/ 63V R465
2 5 29 36 EHT
B DECSDEM/SIF2 EHTO EHT B
SAW102 560K
C221 C222 30 35
SAW102 GND2 AUDEXT/QSSO R311
3
C352
47U/16V
R228 R230
100 100
Q201
C1815
L206
6.8uH
R224 CVBS
CVBS
100
R223 Z201
180 XT-6. 5
GND
Z202
XT-6. 0
GND
Z203 Q202
Q203 XT-5. 5
A A
C1815
GND
C1815
R227 R226
4K7 Z204 4K7
XT-4. 5
GND SYSTEM 1
SYSTEM 1
H_17210_008.eps
5800 A3P610-00 070607
1 2 3 4
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 21
H_17210_009.eps
5800 A3P610-00 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 22
H_17210_010.eps
5800 A3P610-00 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 23
D KEYBOARD CONTROL D
A A
KEYBOARD CIRCUIT
B B
KEYBOARD CIRCUIT
SW008
SW001 SW002 SW003 SW004 SW005 SW006 SW007 M001
C C
PRO- PRO+ VOL- VOL+ MENU SLEEP MUTE
3 2 1
TV/AV
LED001 R**
1K R***
E LED E
100
F F
5V 3
1
KEY 2
GN D 4
IR 5
LED
G G
H_17210_011.eps
5800 D1SL7P-61 080607
1 2 3 4 5 6 7 8 9 10
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 24
H_17210_012.eps
5800 D1SL7P-61 080607
H_17210_013.eps
5800 D1SL7P-61 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 25
E MAIN SWITCH E
H_17210_015.eps
5800 E1SL7P-61 080607
H_17210_014.eps
5800 E1SL7P-61 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 26
G SIDE AV G
H_17210_016.eps
5800 G1SL7P-61 080607
BOTTOM SIDE
H_17210_017.eps
5800 G1SL7P-61 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 27
K K
H_17450_001.eps
200907
H_17450_002.eps
200907
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 28
M SLIM DEFLECTION M
H_17210_019.eps
5800 M3P610-00 080607
H_17210_018.eps
5800 M3P610-00 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 29
Z SUB WOOFER Z
H_17210_020.eps
5800 Z3P610-00 080607
Circuit Diagrams and PWB Layouts SK4.0L CA 7. EN 30
H_17210_021.eps
5800 Z3P610-00 080607
E_06532_012.eps
131004
Alignments SK4.0L CA 8. EN 31
8. Alignments
Index of this chapter: 8.3.3 Screen Voltage Adjust (Key 0).
8.1 General Alignment Conditions
8.2 Hardware Alignments 1. Set picture to “Standard” mode, without signal input.
8.3 Software Alignments 2. Press the keys [i+], “Smart sound” and “Smart picture” to
enter the factory menu. When in “B/W BALANCE” page,
press “mute” on the RC. There will be a level light line
displays.
8.1 General Alignment Conditions
3. Adjust flyback transformers Screen knob till the level bright
line just can be seen, press PROG+ and turn to other
8.1.1 Default Alignment Settings factory menu.
4. When in the light-line screen, CUT R and CUT G can be
Perform all electrical adjustments under the following adjusted if needed with the following RC key mapping:
conditions: To increase /decrease CUT R (See table 8-1)
• Power supply voltage: 230 VAC / 50 Hz (± 10%). To increase /decrease CUT G (See table 8-2)
• Connect the set to the mains via an isolation transformer 5. Press “MUTE” key to return to the “B/W BALANCE” page.
with low internal resistance.
• Allow the set to warm up for approximately 20 to 30 Table 8-1 To increase /decrease CUT R
minutes.
• Measure voltages and waveforms in relation to chassis
ground (with the exception of the voltages on the primary Function CUT R+ CUT R-
side of the power supply). RC key 1 4
Caution: never use heatsinks as ground.
• Test probe: 100: 1, Ri > 10 Mohm, Ci < 3.5 pF. Table 8-2 To increase /decrease CUT G
• Use an isolated trimmer/screwdriver to perform
alignments.
Function CUT G+ CUT G-
RC key 2 5
8.2 Hardware Alignments
8.3.4 Horizontal Adjustment (key 1)
Note: The only hardware alignment in this TV set is the
adjustment of the main voltage (B+), see below.
1. Provide a 50 Hz monoscope pattern.
– Press the keys [i+], “Smart sound” and “Smart picture”
8.2.1 Main Voltage Adjustment
to enter the factory menu.
– Press the keys [i+] again and “ADJUST” appear on
In order to adjust the main voltage, connect a voltage meter to screen.
the cathode of diode D610, and adjust VR601 to a voltage of 2. Press key “0” and adjust “HPH” to set picture horizontal
110 V ±0.3 V. centre to CRT horizontal centre.
8.3 Software Alignments 8.3.5 Vertical & YUV/RGB Horizontal Adjust (key2)
Put the set in its MENU mode (factory mode) as follows (see 1. Provide a 50 Hz cross hatch signal, set TV to standard
also figure “Factory Mode” on the next page): mode. Adjust VSL so that half picture of the pane cross
• Press the keys [i+], “smart sound” and “smart picture” to appears. The picture’s vertical line is just at the bottom of
enter the factory menu. the half picture. Adjust VSL to make the centre of the
• Press the keys [i+] again and “ADJUST” appear on screen. picture’s vertical line and the kinescope are in
• Press the number keys to enter the adjust page, press B/ superposition.
y to choose the items that to be adjusted, Press z/A to 2. Adjust VSI to obtain picture’s vertical re-display ratio more
adjust its value. than 90%.
• Press [i+] to quit factory mode. 3. Provide a 60 Hz cross hatch signal, do step 1 and 2 again
The different alignment parameters are described further on. to adjust.
4. If necessary, fine adjust above items.
8.3.1 Rf AGC Voltage Adjust
8.3.6 OSD Position (Key 4)
1. Provide a 294.25 MHz, 60 dB half colour bar signal.
2. Enter factory mode and press key 1. 1. Menu OSD position adjustment: Provide a 50/60 Hz cross
3. Measure tuner AGC point voltage, adjust AGC item till the hatch pattern. Put the set in MENU mode.
voltage is 2.4 V, or till picture noise just disappears. (typical – Press the keys [i+], “Smart sound” and “Smart picture”
value is at 27). to enter the factory menu.
– Press the keys [i+] again and “ADJUST” appear on
screen.
8.3.2 Focus Fine Adjust
2. LOGO position adjustment: Provide a 50/60 Hz cross
hatch pattern. Put the set in MENU mode. Press key 7 to
1. Provide a cross-hatch pattern signal. enter the factory mode. Adjust XMIN, XMAX, YMIN and
2. Set state to “Rich” mode. YMAX, to obtain LOGO at the centre up to 1/3 of CRT
3. Adjust flyback transformers Focus knob till picture is clear. screen.
3. Press key 4 to enter the factory mode. Adjust VP and HP
item, to obtain menu OSD at the centre of CRT screen.
4. Provide a RGB or YUV cross hatch signal, set the TV in the
standard mode, adjust “YUV OSD HS” 5RGH till picture
horizontal centre is at the CRT centre (optional).
EN 32 8. SK4.0L CA Alignments
Main Page
"I+"
"0" "1" "2"
ADJUST
SOFT VOICE
BRIGHT 50 BASS 30
CONTRAST 57 TREBLE 50
COLOR 45 SURROUND OFF
SHARP 69
YUV SHARP 50
COLOR TEMP WARM
RICH MISIC
BRIGHT 55 BASS 55
CONTRAST 90 TREBLE 60
COLOR 50 SURROUND OFF
SHARP 100
YUV SHARP 50
COLOR TEMP COOL
NATURAL THEATRE
BRIGHT 50 BASS 80
CONTRAST 75 TREBLE 70
COLOR 50 SURROUND ON
SHARP 80
YUV SHARP 50
COLOR TEMP NORMAL
Description of the factory menu Storage address Display string Range (Index value) Default SK4.0L CA
B/W balance
White point R adjustment. 0x00d DRI R 0-63 32 32
White point G adjustment 0x00e DRI G 0-63 32 32
White point B adjustment 0x00f DRI B 0-63 32 32
Black level off-set R adjustment 0x010 CUT R 0-63 32 32
Black level off-set G adjustment. 0x011 CUT G 0-63 32 32
“BRIGHTNESS” of “White Balance Adjustment page” setting 0x02f BT 0-63 32 32
“CONTRAST” of “White Balance Adjustment page” setting 0x030 CT 0-63 32 32
COOL offset according to “DRI R” value of tv, white point R of “COOL” 0x017 COOL DR 0-63 -2 -2
COOL offset according to “DRI G” value of tv, white point G of “COOL” 0x018 COOL DG 0-63 0 0
COOL offset according to “DRI B” value of tv, white point B of “COOL” 0x019 COOL DB 0-63 10 10
COOL offset according to “CUT R” value of tv, black level off-set R of “COOL” 0x01a COOL CR 0-63 0 0
COOL offset according to “CUT G” value of tv, black level off-set R of “COOL” 0x01b COOL CG 0-63 0 0
WARM offset according to “DRI R” value of tv, white point R of “COOL” 0x01c WARM DR 0-63 10 10
Warm offset according to “DRI G” value of tv, white point G of “COOL” 0x01d WARM DG 0-63 0 0
Warm offset according to “DRI B” value of tv, white point B of “COOL” 0x01e WARM DB 0-63 0 0
Warm offset according to “CUT R” value of tv, black level off-set R of “COOL” 0x01f WARM CR 0-63 0 0
Warm offset according to “CUT G” value of tv, black level off-set R of “COOL” 0x020 WARM CG 0-63 0 0
Direct key “0”
50hz/60hz Frequency 60 Hz
Horizontal center ox008 H PH 0-TV-63-TV 31-TV 35-TV
Vertical slope ox009 V SL 0-63 24 30
Vertical center ox00a V SH 0-63 21 22
Vertical amplitude. ox00b V SI 0-63 33 22
Vertical s-correction. ox00c V SC 0-63 27 19
EW WIDTH 0x04b EW WIDTH 0-63 32 51
EW parabola/width 0x04c EW PARA 0-63 32 45
EW upper/lower corner parabola 0x04d UP CORNER 0-63 32 33
Bottom curve 0x04e LO CORNER 0-63 32 33
Horizontal parallelogram 0x04f H-PARA 0-63 32 35
Horizontal bow 0x050 H-BOW 0-63 32 35
EW trapezium 0x051 EW TRAPE 0-63 32 30
Expand 4:3 mode horizontal WIDTH adjust 0x0ed(bit4) ZOOM 0-63 44 44
50hz/60hz Frequency 50 Hz
Horizontal center 0x003 H PH 0-TV-63-TV 31-TV 35-TV
Vertical slope 0x004 V SL 0-63 24 31
Vertical center 0x006 V SH 0-63 21 23
Vertical amplitude. 0x005 V SI 0-63 33 22
Vertical s-correction. 0x007 V SC 0-63 27 21
EW WIDTH 0x044 EW WIDTH 0-63 32 49
EW parabola/width 0x045 EW PARA 0-63 32 45
EW upper/lower corner parabola 0x046 UP CORNER 0-63 32 33
Bottom curve 0x047 LO CORNER 0-63 32 33
Horizontal parallelogram 0x048 H-PARA 0-63 32 35
Horizontal bow 0x049 H-BOW 0-63 32 35
EW trapezium 0x04a EW TRAPE 0-63 32 30
Expand 4:3 mode horizontal WIDTH adjust 0x062 ZOOM 0-63 44 44
Horizontal center in AV source. 0x05e H PH +5-AV 32 33
Horizontal center in AV source. 0x05f H PH +5-AV 32 33
Horizontal center in YUV source. 0x05c H PH +0-YUV 32 33
Horizontal center in YUV source. 0x05d H PH +0-YUV 32 33
Direct key “1”
Out of box setting, Smart Picture: Rich, Contrast +: On, NR: Off, SHIPMODE OFF ON
Smart Sound: Theatre, Tuner Mode: Auto, Volume: 30, CC: Off
RF.AGC adjust 0x002 AGC 0-63 24 23
AGC speed 0x0de (bit5, bit4) AGC SPEED 0-63 1 1
IF choose 0x0dd (bit7, bit6) IF 58.75 Mhz 45.75 Mhz 45.75 Mhz 45.75 Mhz
HRC and IRC of N system for auto search selection 0x0ea (bit4) HRC & IRC OFF ON OFF OFF
ON: PAL M/N ON, OFF: PAL M/N OFF 0x0ea (bit1) MULTI SYSTEM OFF ON ON ON
White apex limit 0x0cb (bit7-bit4) PWL 0-15 0 0
X ray protect 0x0e1 (bit2, bit3) XDT 0-2 1 1
X ray protection detect count 0x073 XDT COUNT 0-255 30 30
NTSC decode matrix 0x0e7(bit2) MUS USA JAP USA USA
PAL, NTSC decode matrix 0x0ed (bit0) MAT OFF ON OFF ON
Bypass of sound bandpass filter 0x0e1 (bit5, bit4) BPB 0-2 1 1
Video dependent coring 0x0de (bit3, bit2) CORING 0-3 3 3
Switch-off in vertical overscan 0x0e7 (bit7) OSO OFF ON ON ON
Direct key “2”
UOC control volume switch 0x0e8 (bit7) UOC VOL SW OFF ON OFF OFF
UOC/PWM modify volume value 0x02e UOC/PWM VOL 0-63 41 40
Volume of 9859 modify value when sound is mono 0x052 MONO GAIN 0-63 48 52
EN 34 8. SK4.0L CA Alignments
Description of the factory menu Storage address Display string Range (Index value) Default SK4.0L CA
Volume of 9859 modify value when sound is stereo 0x053 STEREO GAIN 0-63 48 52
Volume of 9859 modify value when sound is SAP 0x054 SAP GAIN 0-63 48 48
Volume of 9859 modify value when system is AV state 0x055 AV GAIN 0-63 48 50
9859 control pin output state 0x0e0 (bit3, bit2) 9859INPUT 0-2 2 1
10% volume point 0x026 VOL 10 0-100 25 45
25% volume point 0x027 VOL 25 0-100 50 55
50% volume point 0x028 VOL 50 0-100 75 75
80% volume point 0x029 VOL 80 0-100 90 85
100% volume point 0x02a VOL 100 0-100 100 100
FM demodulate frequency width 0x0de (bit1, bit0) FMWS 0-2 0 1
AVL function switch 0x0e8 (bit6) AVL OPT OFF ON OFF OFF
Direct key “3”
AV control logic choose 0x0e1 (bit7, bit6) AV OPT 0-3 1 0
AV choose 0x0cc (bit7-bit4) AV CFG 0-7 3 4
AV2 choose 0x0ea (bit5) 2 AV OFF ON OFF OFF
DVD choose 0x0e9 (bit4) YC/DVD OFF ON OFF OFF
Video output 0x0e7 (bit4) VIDEO OUT IF CVBS CVBS CVBS
Pin 5 choose function 0x0cc (bit3-bit0) PIN 5 NTSC NTSC
Pin 7 choose function 0x0cd (bit7-bit4) PIN 7 VOL1 VOL1
Pin 8 choose function 0x0cd (bit3-bit0) PIN 8 MTUE LED
MUTE pin mode 0x0e9 (bit0) MUTEPIN OFF ON OFF
MODE
OFF: Pin 7 control volume curve 0x0ee (bit6) MUTEPIN SEL OFF
ON: Pin 4 control volume curve
CCD Horizontal width adjust 0x05a CC HP 0-15 13 13
CCD scan Horizontal row when PAL N system 0x060 CC LINE 0-60 21 21
CCD delay adjustment 0x0d1 (bit3-bit0) CC DELAY 8-23 20 12
Direct key “4”
OSD up down position 0x02b VP 0-63 52 52
OSD left right position 0x02c HP 0-63 54 50
RGB/YUV OSD Horizontal Center 0x05b YUV OSD HS 0-60 38 38
OSD output contrast 0x0df (bit7, bit6) OSD L 0-3 0 2
Menu translucence 0x0e9 (bit1) HALFTONE OFF ON ON ON
Software version number SOFTWARE
VERSION
NUMBER
Direct key “5”
Sound mode BTSC-MODE MONO STEREO SAP
Stereo noise limit 0x0ce (bit7-bit4) BTSC-ST 0-15 0 0
SAP noise limit 0x0ce(bit3-bit0) BTSC-SP 0-15 0 0
Sound input level adjustment 0x040 BTSC-LI 0-15 7 9
Separate 0x041 BTSC-A1 0-31 23 14
Separate 0x042 BTSC-A2 0-31 22 6
Time constant 0x0cf (bit7-bit4) BTSC-TC 0-7 4 3
Stereo level switch 0x0e8 (bit3) BTSC-STS OFF ON OFF ON
Stereo adjustment on/off 0x0e8 (bit2) BTSC-ADJ BUSY START START START
MTS detect time delay 0x001 MTS DETECT 0-255 50 50
STEREO and SAP detect count 0x072 MTS FILTER 0-255 20 20
MONO detect count 0x074 MTS FILTER2 0-255 20 3
Direct key “6”
POWER ON MODE 0x0dd (bit3, bit2) POW 0-2 2 2
POWER ON time delay 0x0cb (bit3-bit0) POWER ON TIM 2-17 12 8
Black current stabilization 0x0e8 (bit0) AKB OFF ON ON ON
Black current loop detect 0x0e9 (bit7) NBL OFF ON ON ON
WATCH DOG 0x0eb (bit7) WATCHDOG OFF ON OFF OFF
ON: Philips RC 0x0eb (bit6) PHILIPS RC OFF ON ON ON
OFF: Skyworth RC
VCHIP FUNCTION SWITCH 0x0ea (bit7) VCHIP OFF ON OFF OFF
GAME FUNCTION SWITCH 0x0eb (bit5) GAME OFF ON OFF OFF
CALENDER FUNCTION SWITCH 0x0eb (bit4) CALENDER OFF ON OFF OFF
4:3 expand function choose 0x0ec (bit6) ZOOM OPT OFF ON ON OFF
ON: Blue Screen 0x0e9 (bit6) BLUE BLACK OFF ON ON ON
OFF: Black Screen
EW WIDTH offset according to “EW WIDTH” value when TV is no signal 0x06d BB WIDTH 53-10 +0 0
Video mute during change to program 0x0e1 (bit1, bit0) BLACK BACK 0-2 0 0
RGB BLANKING 0x0ee (bit7) RGB BLANKING OFF ON ON ON
Direct key “7”
Sub contrast 0x057 SUB BRI 0-63 0 4
Sub brightness 0x059 SUB CON 0-63 0 3
Sub color 0x023 SUB COL 0-63 30 30
Sub Sharpness 0x024 SUB SHA 0-63 32 32
TV Sub tint 0x025 SUB TIN 0-31 16 16
AV Sub tint 0x075 SUB TIN-AV 0-31 16 16
PAL Luminance delay 0x0c9 (bit3-bit0) YDL PAL 0-15 2 2
NTSC Luminance delay 0x0c9 (bit7-bit4) YDL NTSC 0-15 2 2
Alignments SK4.0L CA 8. EN 35
Description of the factory menu Storage address Display string Range (Index value) Default SK4.0L CA
AV Luminance delay 0x0ca(bit7-bit4) YDL AV 0-15 4 2
Maximum brightness 0x056 MAX BRI 0-63 63 63
Middle brightness 0x021 MID BRI 0-63 18 18
Maximum contrast 0x058 MAX CON 0-63 63 63
Middle contrast 0x022 MID CON 0-63 15 15
Line-level of brightness 0x02d SC.BRI 0-63 8 8
Direct key “8”
YUV offset according to “DRI R” value of TV, white point R of YUV. 0x012 YUV DR (-32) - (+31) +0 +0
YUV offset according to “DRI G” value of TV, white point G of YUV 0x013 YUV DG (-32) - (+31) +0 +0
YUV offset according to “DRI B” value of TV, white point B of YUV 0x014 YUV DB (-32) - (+31) +0 +0
YUV offset according to “CUT R” value of TV, black level offset R of YUV 0x015 YUV CR (-32) - (+31) +0 +0
YUV offset according to “CUT G” value of TV, black level offset G of YUV 0x016 YUV CG (-32) - (+31) +0 +0
English OSD switch 0x0eb (bit3) ENGLISH OFF ON ON ON
Spanish OSD switch 0x0eb (bit2) SPANISH OFF ON ON ON
French OSD switch 0x0eb (bit1) FRANCE OFF ON OFF OFF
Portuguese OSD switch 0x0eb (bit0) PORTUGUESE OFF ON ON ON
External Y (Luminance) input gain during YPRPB. 0x0ee (bit4) YGN OFF ON OFF ON
OFF: gain 0 dB reduced, ON: gain 3 dB reduced
Cathode drive level 0x0ca (bit3-bit0) CATHE 3 3
EHT tracking mode 0x0ea (bit6) HCO ON ON
Black current measuring lines in overscan 0x0e9 (bit2) OSVE OFF OFF
Manual INIT E2PROM
INITEEP
Key “Smart sound”
BASS set value in Voice state 0x064 BASS 30 30
TREBLE set value in Voice state 0x065 TREBLE 50 50
SURROUND set value in Voice state 0x066 SURROUND OFF OFF
BASS set value in Music state 0x067 BASS 55 55
TREBLE set value in Music state 0x068 TREBLE 60 60
SURROUND set value in Music state 0x069 SURROUND OFF OFF
BASS set value in Theatre state 0x06a BASS 80 80
TREBLE set value in Theatre state 0x06b TREBLE 70 70
SURROUND set value in Theatre state 0x06c SURROUND ON ON
Key “Smart image”
Bright set value in Soft state 0x036 BRIGHT 55 55
Contrast set value in Soft state 0x037 CONTRAST 50 50
Color set value in Soft state 0x038 COLOR 45 45
Sharpness set value in Soft state 0x039 SHARP 45 45
Sharpness set value in Soft state of YUV 0x070 YUV SHARP 50 50
COLOR TEMP set value in Soft state 0x03a COLOR TEMP WARM WARM
Bright set value in Rich state 0x03b BRIGHT 70 70
Contrast set value in Rich state 0x03c CONTRAST 85 85
Color set value in Rich state 0x03d COLOR 70 70
Sharpness set value in Rich state 0x03e SHARP 70 70
Sharpness set value in Rich state of YUV 0x071 YUV SHARP 80 80
COLOR TEMP set value in Rich state 0x03f COLOR TEMP COOL COOL
Bright set value in Natural state 0x031 BRIGHT 50 50
Contrast set value in Natural state 0x032 CONTRAST 75 75
Color set value in Natural state 0x033 COLOR 50 50
Sharpness set value in Natural state 0x034 SHARP 50 50
Sharpness set value in Natural state of YUV 0x06f YUV SHARP 50 50
COLOR TEMP set value in Natural state 0x035 COLOR TEMP NORMAL NORMAL
EN 36 9. SK4.0L CA Circuit Descriptions, Abbreviation List, and IC Data Sheets
SAP Demodulator
9.1 Introduction
The composite signal is fed from the output of the input level
adjustment stage to the SAP demodulator circuit through a 5fH
The SK4.0A CA is a CRT TV for the year 2007, based on the band-pass filter. The demodulator level is automatically
3P61 platform. In this chapter, only a general description of the controlled. The SAP demodulator includes an internal field
various circuits is given. For more detailed information, see the strength detector that mutes the SAP output in the event of
circuit diagrams in this manual. insufficient signal conditions. The SAP identification signal can
be read by the I2C-bus.
9.2 The various circuits
Noise Detector
The composite input noise increases with decreasing antenna
9.2.1 Tuner
signal. This makes it necessary to switch stereo or SAP off at
certain thresholds. These thresholds can be set via the I2C-
The function of the tuner is to select the channel to be received bus. With ST0 to ST3 the stereo threshold can be selected and
and suppress the interference of neighboring channels, to
with SP0 to SP3 the SAP threshold. A hysteresis can be
amplify the high frequency signal, to improve the receiving
achieved via software by making the threshold dependent of
sensitivity and SNR, and to generate a PIF signal through the identification bits STP and SAPP.
frequency conversion.
Mode Selection
9.2.2 IF Channel
The stereo/SAP switch feeds either the L - R signal or the SAP
demodulator output signal via the internal dbx noise reduction
The IF Channel mainly ensures the sensitivity and selectivity of circuit to the dematrix/switching circuit. Different switch modes
the complete TV set. The IF AMP integrated in the UOCIII is provided at the output pins OUTR and OUTL are available.
made up of a three-stage dual-differential amplifier with a gain
value above 70dB, a SNR of 55dB and a bandwidth of 7 MHz. dbx Decoder
The video demodulation circuit is made from the built-in PLL The dbx circuit includes all blocks required for the noise
Sync Detector. The spectrum of the demodulation carrier is
reduction system in accordance with the BTSC system
unitary and it is not affected by the content of the video signal.
specification. The output signal is fed through a 73 ms fixed de-
The tuner features stable receptivity while the signal output emphasis circuit to the dematrix block.
from the video detector features high fidelity. The built-in PLL
circuit of the UOCIII generates a 38.0 MHz or 38.9 MHz
SAP Output
demodulation reference signal for the sync detector to
demodulate the video signal; this is called “PLL sync Independent of the stereo/SAP switch, the SAP signal is also
available at pin SAP. At SAP, the SAP signal is not dbx
demodulation”.
decoded. The capacitor at SDE provides a recommended de-
emphasis (150 ms) at SAP.
9.2.3 Sound Channel
Integrated Filters
An external ceramic filter is used to select the second SIF
The filter functions necessary for stereo and SAP demodulation
signal for the sound channel of UOCIII from the signal output of
and part of the dbx filter circuits are provided on-chip using
the video detector. The audio signal is obtained after limiting transconductor circuits. The required filter accuracy is attained
amplification and demodulation by the intermediate frequency
by an automatic filter alignment circuit.
detector for the SIF signal, and then the audio signal is fed to
the BTSC stereo/SAP decoder TDA9850. From that it is output
to the audio amplifier TFA9842, which drives the speakers to 9.2.5 CRT Drive Circuit
provide the sound. The intermediate frequency detector and
volume-control attenuator that are built in the UOCIII are set In the driver circuit, both the voltage and current of the R/G/B
and adjusted via the CPU. signal are amplified, after which the CRT drive circuit
modulates the cathode beam current of the CRT. The R/G/B
signal input into the driver circuit is of negative polarity.
9.2.4 BTSC stereo/SAP decoder
H_17210_039.eps
120607
H_17210_039.eps
120607
Block Diagram
THERMAL TDA4865AJ
PROTECTION
DIFFERENTIAL
VERTICAL FLYBACK REFERENCE
INPUT
OUTPUT GENERATOR CIRCUIT
STAGE
7 6 5 4 3 2 1
INP INN VOUT GND VP2 VP3 VP1
RS1 CS1 CF
D1
C2
deflection R5
RP
coil
R3
C1
R6
from
deflection controller R1
R2
VN VP
Pin Configuration
VP1 1
VP3 2
VP2 3
GND 4 TDA4865AJ
VOUT 5
INN 6
INP 7
H_17210_035.eps
120607
Block Diagram
Pin Configuration
H_17210_041.eps
120607
Block Diagram
VCC
9
4 8
IN1 OUT1
60
kΩ
1 2
IN2 OUT2
60
kΩ
3 SHORT-CIRCUIT
CIV AND
TEMPERATURE
VREF
PROTECTION
VCC
7 VOLUME
VC
CONTROL
0.5VCC 6
SVR
TFA9842AJ
GND
Pin Configuration
IN2 1
OUT2 2
CIV 3
IN1 4
GND 5 TFA9842AJ
SVR 6
VC 7
OUT1 8
VCC 9
H_17210_033.eps
110607
Block Diagram
C3 +
C4 ceramic
C2 + C5 Q1 resonator C6 + C7 +
R1
13 14 15 16 17 18 19
L+R stereo
27
DEMATRIX OUTL mono
+ SAP
STEREO DECODER MODE to
L − R/SAP 21
SELECT OUTR audio
processing
TDA9850
C8
22
composite INPUT NOISE STEREO/SAP
11 DE-EMPHASIS
+
7
SAP STEREO SUPPLY LOGIC, I2C-
DBX ADJUST TRANSCEIVER
DEMODULATOR 28
MAD
5 4 26 3 1 2 32 31 30 29 25 20 10 12 6 24 8 9
R2
+ + + + + + + + + +
C16 C15 C17 C19 C18
C14 C12 C11 C10 C9 CL CR
R3 SDA SCL
Pin Configuration
VEO 1 32 CS
VEI 2 31 CW
CNR 3 30 CTS
CM 4 29 CTW
CDEC 5 28 MAD
AGND 6 27 OUTL
DGND 7 26 CND
SDA 8 25 CL
TDA9850
SCL 9 24 Vref
VCC 10 23 SAP
COMP 11 22 CSDE
VCAP 12 21 OUTR
CP1 13 20 CR
CP2 14 19 CSS
CPH 15 18 CMO
CADJ 16 17 CER
H_17450_004.eps
200907
Block Diagram
H_17210_034.eps
130607
Pin Configuration
H_17210_029.eps
130607
H_17210_030.eps
130607
Pinning
H_17210_031.eps
130607
Block Diagram
QSSO/AMOUT/AUDEXT
AUDOUT/AMOUT
ADC IN (4x)
SOUND
VST OUT
RESET
TRAP
SIFIN
VPE
TUNERAGC
IFVO/SVO
REF
H
VIDEO SWITCH LUMA DELAY
CLOSED CAPTION OSD
VIDEO IDENT. CVBS
CVBS/Y PEAKING ROM/RAM
ACQUISITION V DISPLAY
VIDEO FILTERS BLACK STRETCH
C
SYNC COR R G B BL
REF RO
CONTR/BRIGHTN
BASE-BAND OSD/TEXT INSERT GO
PAL/NTSC
(REFOUT) BO
DECODER DELAY LINE CCC
WHITE-P. ADJ. BCLIN
BLKIN
R G B
Pin Configuration
handbook, halfpage
P1.3/T1 1 64 P1.2/INT0
P1.6/SCL 2 63 P1.1/T0
P1.7/SDA 3 62 P1.0/INT1
P2.0/TPWM 4 61 VDDP
P3.0/ADC0/PWM0 5 60 RESET
P3.1/ADC1/PWM1 6 59 XTALOUT
P3.2/ADC2/PWM2 7 58 XTALIN
P3.3/ADC3/PWM3 8 57 OSCGND
VSSC/P 9 56 VDDC
P0.5 10 55 VPE
P0.6 11 54 VDDA
TDA937X PS/N2 series (SDIP-64)
VSSA 12 53 BO
I.C. 13 52 GO
VP2 14 51 RO
DECDIG 15 50 BLKIN
16 49 BCLIN
PH2LF
XXX
PH1LF 17 48 B2/U/PBIN
GND3 18 47 G2/YIN
DECBG 19 46 R2/V/PRIN
AVL/EWD/ 20 45 INSSW2
DECSDEM
VDRB 21 44 AUDOUT
VDRA 22 43 C
IFIN1 23 42 CVBS/Y
IFIN2 24 41 GND1
IREF 25 40 CVBS1
VSC 26 39 VP1
AGCOUT 27 38 IFVO/SVO
AUDEEM/SIFIN1 28 37 PLLIF
DECSDEM/SIFIN2 29 36 EHTO
GND2 30 35 AUDEXT/QSSO
31 34 FBISO
SNDPLL/SIFAGC
AVL/SNDIF/REFO/ 32 33 HOUT
H_17450_012.eps
AUDEEM 210907
H_17210_035.eps
120607
Pin Configuration
H_17210_036.eps
120607
R326 9965 000 39977 CFR 100kΩ J835 9965 100 04921 Peaking Coil 56μH 10% IC602 9965 100 04915 TLP421 TOSHIBA
R327 9965 100 04854 1.5kΩ 5% 1W J836 9965 100 04921 Peaking Coil 56μH 10% IC604 9965 000 40247 L7808CV
R401 9965 000 40686 CFR 15kΩ 1/16W J837 9965 100 04921 Peaking Coil 56μH 10% Q101 9965 000 40584 2SC3779D
R402 9965 000 40686 CFR 15kΩ 1/16W J838 9965 100 04921 Peaking Coil 56μH 10% Q201 9965 000 40232 2SC1815Y/2PC1815
R405 9965 000 40304 CFR 1KΩ 1/16W J849 9965 000 40700 CFR 4.7kΩ 1/16W Q204 9965 000 40232 2SC1815Y/2PC1815
R406 9965 000 40304 CFR 1KΩ 1/16W l601 9965 000 41227 Bead 3.5 x 1 x 9mm Q302 9965 100 04914 3DD5032/D5032
R407 9965 000 39976 CFR 10kΩ 1/16W L101 9965 000 40602 Peaking coil 1μH 10% Q303 9965 000 41191 Trans. FQPF630
R408 9965 000 40700 CFR 4.7kΩ 1/16W L102 9965 000 40253 Peaking coil 100μH 10% Q401 9965 000 40232 2SC1815Y/2PC1815
R409 9965 000 40695 CFR 3.3kΩ 1/16W L103 9965 100 04921 Peaking Coil 56μH 10% Q402 9965 000 40231 2SA1015Y\2PA1015
R410 9965 100 04837 130kΩ 5% 1/16-1/6W L201 9965 000 40252 Peaking coil 10μH 10% Q450 9965 000 40234 2SC2482/3DG2482Y
R411 9965 000 39976 CFR 10kΩ 1/16W L202 9965 000 40252 Peaking coil 10μH 10% Q501 9965 000 40238 BF422 NPN (250V)
R501 9965 000 40690 CFR 22Ω 1/16W L203 9965 000 40252 Peaking coil 10μH 10% Q502 9965 000 40239 BF423 PNP (-250V)
R502 9965 100 04839 2.2kΩ 5% 1/6W L204 9965 000 40252 Peaking coil 10μH 10% Q503 9965 000 40238 BF422 NPN (250V)
R503 9965 000 40491 CFR 270Ω 1W L205 9965 000 40252 Peaking coil 10μH 10% Q504 9965 000 40238 BF422 NPN (250V)
R504 9965 000 40690 CFR 22Ω 1/16W L206 9965 100 04920 Peaking Coil 6.8μH Q505 9965 000 40239 BF423 PNP (-250V)
R505 9965 100 04858 270Ω 5% 1W L301 9965 100 04922 Choke Coil 105μH Q506 9965 000 40238 BF422 NPN (250V)
R506 9965 000 40517 MOFR 15kΩ L302 9965 100 07718 Linear Coil 36μH Q507 9965 000 40238 BF422 NPN (250V)
R507 9965 100 04856 220Ω 5% 1W L303 9965 100 07717 Choke Coil 2.8MHz 10% Q508 9965 000 40239 BF423 PNP (-250V)
R508 9965 100 04853 1kΩ 5% 1W L304 9965 100 04924 Choke Coil 790μH Q509 9965 000 40238 BF422 NPN (250V)
R510 9965 000 39998 CFR 22Ω 1/4W L401 9965 000 40252 Peaking coil 10μH 10% Q601 9965 100 06016 KA431Z Fairchild
R511 9965 000 40000 CFR 2.2kΩ L501 9965 000 40252 Peaking coil 10μH 10% Q602 9965 100 04913 Transistor 2SC2120Y
R512 9965 000 39998 CFR 22Ω 1/4W L605 9965 000 40255 Choke coil 100μH 10% Q603 9965 000 40232 2SC1815Y/2PC1815
R513 9965 000 40491 CFR 270Ω 1W L801 9965 100 04847 560Ω 5% 1/16-1/6W Q604 9965 000 40232 2SC1815Y/2PC1815
R514 9965 100 04858 270Ω 5% 1W L802 9965 100 04847 560Ω 5% 1/16-1/6W Q606 9965 100 04912 2SA1013
R515 9965 000 40517 MOFR 15kΩ L805 9965 100 04847 560Ω 5% 1/16-1/6W Q608 9965 000 40231 2SA1015Y\2PA1015
R516 9965 100 04856 220Ω 5% 1W L806 9965 100 04847 560Ω 5% 1/16-1/6W Q803 9965 000 40232 2SC1815Y/2PC1815
R517 9965 100 04853 1kΩ 5% 1W T301 9965 100 04931 21" Transformer B+115V Q804 9965 000 40232 2SC1815Y/2PC1815
R519 9965 000 40503 CFR 220kΩ 1W T302 9965 100 05412 Transformer BCT-19G GST601 9965 000 40274 Surge Abs. 300V 30%
R520 9965 100 04839 2.2kΩ 5% 1/6W T302 9965 100 07484 Horizontal Drive Transf. J241 9965 000 40252 Peaking coil 10μH 10%
R521 9965 000 39998 CFR 22Ω 1/4W T601 9965 100 05324 Line Filter 30mH x 2 J249 9965 000 40252 Peaking coil 10μH 10%
R522 9965 000 39998 CFR 22Ω 1/4W T602 9965 100 05324 Line Filter 30mH x 2 J625 9965 000 40218 1N4148 150mA/100V
R523 9965 000 40491 CFR 270Ω 1W T604 9965 100 04932 Switching Transf. Ec40 J629 9965 000 39975 CFR 100Ω 1/16W
R524 9965 100 04858 270Ω 5% 1W J632A 9965 000 40700 CFR 4.7kΩ 1/16W
R525 9965 000 40517 MOFR 15kΩ
R526 9965 100 04856 220Ω 5% 1W d
R527 9965 100 04853 1kΩ 5% 1W
D101 9965 000 40221 Zener 5V1 1/2W 5%
Keyboard & Control Panel [E]
R601 9965 000 40150 High Volt. 2.2MΩ 1/2W
D201 9965 000 40221 Zener 5V1 1/2W 5%
R602 9965 100 04857 220kΩ 5% 1W
R603 9965 000 40524 NTC 5/5A
D202 9965 000 40224 Zener 8V2 1/2W 5% Various
D203 9965 000 40224 Zener 8V2 1/2W 5%
R604 9965 000 40698 CFR 39kΩ 1/16W
D204 9965 000 40224 Zener 8V2 1/2W 5% SW002 9965 100 04934 Tact Switch
R605 9965 000 40691 CFR 220Ω 1/16W
D205 9965 000 40218 1N4148 150mA/100V SW004 9965 100 04934 Tact Switch
R606 9965 000 40706 CFR 6.8kΩ 1/16W
D206 9965 000 41175 6V2 5% 1/2W
R607 9965 000 39998 CFR 22Ω 1/4W
D207 9965 000 40221 Zener 5V1 1/2W 5%
R608 9965 100 04839 2.2kΩ 5% 1/6W
D301A 9965 000 40224 Zener 8V2 1/2W 5% g
R609 9965 000 40154 High Volt. 8.2MΩ 1W
D302 9965 000 40219 BA158 600V/1A
R611 9965 100 04849 680Ω 5% 1/16-1/6W CR1 9965 100 04879 10μF 20% 10V
D303 9965 000 40219 BA158 600V/1A
R612 9965 100 04839 2.2kΩ 5% 1/6W
D304 9965 000 40219 BA158 600V/1A
R613 9965 000 40304 CFR 1KΩ 1/16W
R614 9965 100 04845 4.3kΩ 5% 1/16-1/6W
D305 9965 000 40218 1N4148 150mA/100V f
D306 9965 000 40224 Zener 8V2 1/2W 5%
R615 9965 000 40490 CFR 220kΩ 1W
D307 9965 000 40218 1N4148 150mA/100V RD2 9965 000 40693 CFR 2.7kΩ 1/16W
R616 9965 100 04862 0.22Ω 5% 1W
D308 9965 000 40219 BA158 600V/1A RD3 9965 000 39975 CFR 100Ω 1/16W
R617 9965 100 04863 0.33Ω 5% 1W
D309 9965 100 04909 Zener Diode 18V 1/2W RD4 9965 000 40688 CFR 18kΩ 1/16W
R618 9965 100 04863 0.33Ω 5% 1W
D310 9965 000 40219 BA158 600V/1A RD5 9965 000 39976 CFR 10kΩ 1/16W
R619 9965 100 04858 270Ω 5% 1W
D311 9965 100 04906 3A/800V(DO-27) M001 9965 000 40270 IR receiver mod. 36kHz
R621 9965 100 04855 22Ω 5% 1W
D312 9965 100 04904 BY228
R622 9965 100 04851 820Ω 5% 1/16-1/6W
R623 9965 000 40101 CFR 3.3kΩ D401 9965 000 40218 1N4148 150mA/100V
R624 9965 000 39976 CFR 10kΩ 1/16W D402 9965 000 40218 1N4148 150mA/100V BTSC Board [K]
R625 9965 000 39976 CFR 10kΩ 1/16W D501 9965 000 40218 1N4148 150mA/100V
R626 9965 000 39976 CFR 10kΩ 1/16W D502 9965 000 40219 BA158 600V/1A
D503 9965 000 40218 1N4148 150mA/100V Various
R630 9965 000 39999 CFR 220Ω
R632 9965 000 39976 CFR 10kΩ 1/16W D504 9965 000 40219 BA158 600V/1A
D505 9965 000 40218 1N4148 150mA/100V X801 9965 100 07714 Cer. Res. 503kHz
R633 9965 000 40304 CFR 1KΩ 1/16W
R637 9965 000 40517 MOFR 15kΩ D506 9965 000 40219 BA158 600V/1A
R638 9965 000 39984 CFR 75Ω 1/16W D603 9965 000 40219 BA158 600V/1A g
R639 9965 000 39976 CFR 10kΩ 1/16W D604 9965 100 04909 Zener Diode 18V 1/2W
D605 9965 100 04911 TA20-08 2A/800V C801 9965 100 05388 1µF 20% 50V
R640 9965 100 04937 Bead 3.5 X 1 X 5mm
R640 9965 100 06020 Bead 3.5 X 1 X 5mm D606 9965 100 04911 TA20-08 2A/800V C802 9965 100 07708 0.47µF 10% 63-100V
R801 9965 000 40705 CFR 68Ω 1/16W D607 9965 100 04911 TA20-08 2A/800V C803 9965 000 41112 4.7μF 20% 16V
D608 9965 100 04911 TA20-08 2A/800V C804 9965 100 07706 0.22μF 50V
R802 9965 100 04838 180Ω 5% 1/16-1/6W
R804 9965 100 05140 2.4kΩ 5% 1/16-1/6W D609 9965 100 04907 3V6 1/2W +/-5% C805 9965 000 40171 10μF 20% 16V
R805 9965 100 05140 2.4kΩ 5% 1/16-1/6W D610 9965 100 07483 High Speed Rect. RU4 C806 9965 000 41112 4.7μF 20% 16V
D611 9965 100 04906 3A/800V(DO-27) C807 9965 000 41112 4.7μF 20% 16V
R806 9965 000 39975 CFR 100Ω 1/16W
R807 9965 000 39975 CFR 100Ω 1/16W D612 9965 000 40219 BA158 600V/1A C808 9965 000 40561 Mylar 0.015μF 100V
R817 9965 100 05140 2.4kΩ 5% 1/16-1/6W D613 9965 100 04905 TRU3YX 200V/2A C809 9965 000 40171 10μF 20% 16V
D615 9965 000 40219 BA158 600V/1A C810 9965 000 40171 10μF 20% 16V
R818 9965 100 05140 2.4kΩ 5% 1/16-1/6W
R835 9965 000 39976 CFR 10kΩ 1/16W D616 9965 000 40220 Zener 3V9 1/2W 5% C811 9965 000 40178 1μF 20% 50V
R836 9965 000 39976 CFR 10kΩ 1/16W D617 9965 000 40218 1N4148 150mA/100V C812 9965 000 40178 1μF 20% 50V
D801 9965 000 40224 Zener 8V2 1/2W 5% C813 9965 100 07707 0.047µF 50V
R841 9965 000 40700 CFR 4.7kΩ 1/16W
R842 9965 000 40700 CFR 4.7kΩ 1/16W D802 9965 000 40224 Zener 8V2 1/2W 5% C814 9965 000 40171 10μF 20% 16V
R843 9965 000 40252 Peaking coil 10μH 10% D803 9965 000 40224 Zener 8V2 1/2W 5% C815 9965 000 40157 0.1μF 50V
D804 9965 000 40224 Zener 8V2 1/2W 5% C816 9965 000 41112 4.7μF 20% 16V
R844 9965 000 39975 CFR 100Ω 1/16W
R847 9965 000 39975 CFR 100Ω 1/16W D805 9965 000 40224 Zener 8V2 1/2W 5% C817 9965 000 40157 0.1μF 50V
R852 9965 000 40685 CFR 1.5kΩ 1/16W C818 9965 000 40172 100μF 20% 16V
C819 9965 000 40172 100μF 20% 16V
R854 9965 000 40685 CFR 1.5kΩ 1/16W ce
RST601 9965 100 04856 220Ω 5% 1W C821 9965 100 05388 1µF 20% 50V
RT602 9965 100 04865 Ther Resistor 9Ω for 29" IC101 9965 000 40249 KA33V C822 9965 100 05388 1µF 20% 50V
VR601 9965 000 40155 Semi-fixed R 1KB (H) IC201 9965 100 07701 uP C823 9965 000 40180 2.2μF20% 50V
IC202 9965 000 40597 8k-BIT IIC EEPROM C824 9965 000 40180 2.2μF20% 50V
IC301 9965 100 04918 TDA4865AJ DBS7P C825 9965 000 41097 100pF 50V
b IC401 9965 000 40596 TDA9859 C826 9965 000 41097 100pF 50V
IC402 9965 100 04917 TFA9842AJ PHILIPS C827 9965 000 40171 10μF 20% 16V
J807 9965 100 04921 Peaking Coil 56μH 10% C828 9965 000 40157 0.1μF 50V
IC601 9965 100 04916 STR-W6554A SANKEN
J808 9965 100 04921 Peaking Coil 56μH 10% C829 9965 100 05388 1µF 20% 50V
Spare Parts List SK4.0L CA 10. EN 55
f
R801 9965 100 04839 2.2kΩ 5% 1/6W
R802 9965 100 05146 8.2kΩ 5% 1/16-1/6W
R803 9965 000 39979 CFR 150Ω 1/6W
R804 9965 000 40252 Peaking coil 10μH 10%
R805 9965 000 39975 CFR 100Ω 1/16W
R806 9965 000 39975 CFR 100Ω 1/16W
R807 9965 000 39976 CFR 10kΩ 1/16W
R808 9965 000 39976 CFR 10kΩ 1/16W
R810 9965 000 40304 CFR 1KΩ 1/16W
ce
IC801 9965 100 07712 TDA9850 (IIC Bus)
IC802 9965 100 07713 L78L09CZ SGS TO-92
Q801 9965 000 40232 2SC1815Y/2PC1815
EN 56 11. SK4.0L CA Revision List