Professional Documents
Culture Documents
http://english.electronica-pt.com/lcd-repair
http://translate.googleusercontent.com/translate_c?
depth=1&hl=ro&rurl=translate.google.ro&sl=ru&tl=en&u=http://monitor.net.ru/forum/topic239071-
0.html&usg=ALkJrhhj-mySUUYNsMu4dIV06KGFiKa7jQ
http://www.d43d.ru/modules.php?name=Content&pa=showpage&pid=33 - here's a
couple of circuits with a brief description of it.
slap 16-09-2008 19:47
Party
Posts: Rottor,
342
Aleh I disconnect the faulty lamp installation of capacitors instead of the lamp.
The order of 1000-2000 pF about 2 kilovolts. The exact denomination is possible to
choose a particular LSD.
"Deceived" for many inverters - returns were not.
Can be made equivalent to the resistors, but it turns out it is very large.
A capacity enables you to do all compact.
KRAB 16-09-2008 19:53
monitor.
net.ru slap, the question is, as I understand that one of the trance "killed" and equivalents
lamps examined the link above
Posts: KRAB wrote:
14071 You can still share some thoughts about the equivalent of lamps. Someone
uses (recommended)
1. Resistors: "... 100k 2-10VT power ...." - cm. And "priveshenny" file.
2. The high-voltage capacitors "... 3 kV capacitor 33-47pF ..."
3. For example, I used a 20-watt fluorescent lamp (lamps from China) with
closed terminal of each "spiral" ignition.
I'm in this area lamEr, so I was only interested in specific settings, and for adults.
KRAB 16-09-2008 20:16
monitor.
net.ru Rottor wrote:
1 - with two transformers and three-defective lamps
Posts: - Instead of the 4th lamp - equivalent (the links above - from Andrew andros).
14071
Rottor wrote:
2 - one transformer is necessary to ensure proper illumination of the work on
the three lamps.
- IMHO - not work - power tr-ra is not enough.
Rottor wrote:
3 - light "flashing" or "red" lamp at maximum brightness.
- ??? - May produce heat and failure of key assemblies.
Alex, this is a specific target for this type of "inverter OZ960", or just need a TV
version of "powering" existing in a matrix of light - so then just another type of
inverter is ready to take?
Strike 16-09-2008 20:39
idiot
Posts: ?.
2177 I'll try ..
If the above scheme 1, then selecting R18 upward failure protection is achieved
because the after removal of faulty trance removes the additional voltage source for
the feedback.
Or as an option - will integrate ostsyllogram point (45) is carried out, this may be
enough.
Rottor 16-09-2008 20:44
Guest
87.69. *. KRAB wrote:
*
1 - instead of the 4th lamp - equivalent (the links above - from Andrew
andros).
2 - IMHO - not work - power tr-ra is not enough.
3 - is a particular challenge for this type of "inverter OZ960"
1 - Read about the different "emulators" including the load resistor, tried in practice -
for me not aktualtno.
2 - Why is not enough - trans quietly "shakes" four - six lamps with optimum
brightness.
If necessary, you can reduce the total power, luminous flux (brightness) with an ample
margin.
3 - In this instance, to discuss options, my problem has been solved independently, but
would like to get the information for free.
Tried at the time to "discuss" about it in the "Monitoring" section of the forum - but
there are steep "pro" smoothed out all the messages.
May still have time popizdet on this topic here, to the third warning, followed by
"indefinite ban."
Strike wrote:
If the above scheme 1, then selecting R18 upward failure protection is
achieved,
I can say straight away - manage security on pins 2, 9, 10, by simple means (such as
the selection of the resistor) is not possible.
At least I did not.
In the archives of different forums, taking into account long-term practice of repair, I
found nothing.
However, maybe information is not available or I casually looking for.
PAI 17-09-2008 9:39
Master
Posts: Rottor wrote:
1342
1 - to provide a simple circuit design means the inverter with a transformer
for operation without a faulty transformer, with the minimum required
number of lamps.
For lamps up to 17 "- load 270pik from 19" - 470pik. Load tested for years. No return.
Rottor wrote:
If you remove (at fault) or lamp transformer - protection trips, the inverter
shuts down the entire block
Therefore it is necessary to put in Conder parallels faulty lamp. This is for options-
Rottor wrote:
with two transformers and three-defective lamps
Rottor wrote:
2 - one transformer is necessary to ensure proper illumination of the work on
the three lamps.
This is an interesting option. I'll try. Good is the ward for the experiment.
Rottor 17-09-2008 10:00
Guest
89,138. PAI, Ok!
*. * This indirect ways - "emulation" is equivalent to maintaining a regular mode circuits -
Protection continues to work.
I read about it on various forums, you have to "monitor" is a topic where it is
established by Directive moderator.
You do not have information on ways to incorporate chip (s) in order to disable the
protection and transfer it in the "manual" mode is controlled?
LARTE 17-09-2008 19:42
R
Mozgop Rottor, he tripled his foot looks protection diodes sealed-off from the trance that was
rav dead and everything should work.
Posts:
3477
Rottor 17-09-2008 19:52
Guest
87.69. *. LARTER wrote:
*
... And everything should work.
Your prayers?
Rottor wrote:
I can say straight away - manage security on pins 2, 9, 10, by simple means
(such as the selection of the resistor) is not possible.
A processor (PWM) inverter detects a failed or overloaded lamp and goes into
protection?
LARTE 17-09-2008 19:56
R
Mozgop Rottor, on the second scheme, one transformer, one lamp, 9i10 foot m / s looking for
rav ignition and support of indigenous and second overall protection of the inverter when
neispravnogsti any of the lamps.
Posts:
3477
Yes, not on a specific chip, but the exact same circuitry, the diode sealed off and it
stops svalivatsya in defense on the channel on which it stands. Even if the keys are to
blame trans swing, m / s will not see the error and will work. According to datasheet 2
output is called OVP (protection).
Here it vnutrinney.
Your opinion is inconsistent with the specific work "m / s", read carefully the topic.
Posts:
3477
Posts:
3477
I'm interested in the opinion of those who specifically faced with the problem -
remove the protection, that is to provide the operating mode chip circuit design
method, for example, without tripping feedbacks watering parts manufacturing
"emulators".
and when it is lower then the threshold can be made so. divider vystavlyaetsya lower
threshold. Zener ogranichivaetsya top.
and the voltage at the divider probably better served from 7 O (Reference voltage
output; 2.5V typical)
Posts:
18438
Rottor, off protection easily lock timer capacitor .Konkretno probyval for OZ9938.V
OZ960 see a similar foot-1 CTIMR.Etot capacitor starts charging to trigger sensors
and on time by the charges of protection zablokirovany.Shunt kiloomnikom capacitor
permanently stop protection
Rottor 18-09-2008 20:40
Guest
87.69. *. victorian,
* Indistinctly.
Whether a turnkey solution, or offer "method" for implementation.
I was unable to solve the problem this way.
If you have more specific information you specify.
- Connect the output circuit 1 through 5 to 1k or "ground" is not blocking protection.
Pin 1 is the type of "Reset" to include, to enter the chip in operation.
Protection throughout the range PWM checked against the saw formed capacitor at
pin 4 "soft start".
At the moment when the work circuit (glow lamp) in emergency mode is determined
by the capacitor on pin 4.
- The capacitor on pin 4 defines what is described as "The lamps are lit for a few
seconds and go out."
The capacitor on pin 1 to blocking protection does not apply.
Strike 18-09-2008 21:17
idiot
Posts: Rottor, could not, would lay the waveform (from 1 scheme) 45,46,47?
2177
Posted 18-09-2008 23:30
I can assume that you can use the "saw" output from the chip and make it to the
protection scheme.
Thus, the PWM will not "see" the output stage.
Rottor 18-09-2008 21:47
Guest
87.69. *. Strike,
* I'm sorry but I have no such devices to be repaired, and the scheme I have
downloaded from the internet.
I have a workshop area and LCD comes a couple of times a month at best.
With regard to the repair of inverters "ostsiloskopirovaniem" is empty, then I figured
out the pros - pizdobolami owning such sophisticated techniques.
http://monitor.net.ru/forum/viewtopic.php?t=151397
I'm not an expert on LCD but I can really help with the repair procedure and
instructions about how to disable protection.
Strike wrote:
I can assume that you can use the "saw" output from the chip and make it to
the protection scheme.
The assumption is true, because it is the only and the easiest way to solve the external
pins.
The only question is in the process of implementation.
Strike 18-09-2008 22:22
idiot
Posts: Some chips have a test mode, as understood it is necessary to drive them to
2177 "Generotora"
While there are no developments, on occasion try.
Rottor 18-09-2008 23:08
Guest
87.69. *. Strike,
* I was hoping for a discussion of this topic but it seems that the "repair" LCL is the
swan song as the last stage in the rank of specialist - in this profession a TV technician
ends.
All smoothly into the name of the board, Part Number, trade eblom or components
depending on the degree of access.
I applied voltage limiter key to fix the potential of the capacitor which is charged by a
current source in the chip.
As adjustable voltage regulator is used reverse-(locked) and the diode voltage source
5V.
Ie drinking freely formed but a certain threshold, which determines the PWM constant
power and brightness of the lamps, respectively, while maintaining a smooth start.
The addition of two parts allows you to block the installation of protection circuits
constant brightness level adjustable potentiometer.
This can be used as a temporary technological device repair inverters to force start to
identify the causes of faults using a chip.
Rottor 19-09-2008 8:59
Guest
89,138. gavrykgsm wrote:
*. *
For defektovaniya and identify faults in the inverter to OZ960 there is much
more acceptable and less effective ways to ...
Rottor, clarify, worked with OZ9938, normally locked, I lied about kiloomnika
memory nor chёrtu.Shuntiroval likely 100 kilohms, as came to this possibility probe
ostsila. Leg 1-CTIMR-rezet not, I have translated as blocking protection time
(charge CTIMR), necessary for reliable ignition with a range of lamp types (length,
diameter of the lamp, the current temperature) .Po flowchart OZ960 see the
connection between CCFL and software start-so low impedance shunt may simply
puts start.Po dispute about the necessity and convenience of blocking protection
during Troubleshooting-absolutely necessary.
Rottor 19-09-2008 12:37
Guest
89,138. gavrykgsm wrote:
*. *
... Describe something you can only STE unlikely someone will like
victorian wrote:
Shunted likely 100 kilohms, as came to this possibility
In your post there is only a protocol of intent - which does not allow vospolzovatsya
information you provide to accomplish the task.
It only spreads the topic making it long and unreadable.
If there is no specific information, then do not replace it and smearing projests
semolina on a plate.
victorian wrote:
Leg 1-CTIMR-rezet not, I have translated as lock protection
How remark accept BUT:
- No error.
About the "Pin 1 is the type of" Reset "I initially written in quotation marks.
This time delay is relevant to the protection (timing), it starts with a "zero" that is,
with a power-on reset - it means nothing more than a "Reset" by the process.
- This does not conflict in the context of my discussion of the interpretation of the
idea of blocking.
According to the spelling intended output does not match the chip only Pdf.
victoria 19-09-2008 13:39
n
Party Rottor wrote:
Posts:
The technique is simple a complete description of meaningful action solves
972
the problem that is designated as "Unprotect inverter?"
I just shared his own experience, without pretending to "technique", that's for you to
choose the right way, otherwise
Rottor wrote:
semolina on a plate.
Rottor wrote:
About the "Pin 1 is the type of" Reset "I initially written in quotation marks.
This time delay is relevant to the protection (timing), it starts with a "zero"
that is, with a power-on reset - it means nothing more than a "Reset" in a
manner
In the particular case of transients when the yes, generally "zero" starts with
emergency information from the sensors and during raboty.Formiruetsya delay from:
sensor-off charge drayva.Blokiruya known capacitor stretch on time to protect
beskonechnosti.Chto uncomprehended I suggested?
Strike 19-09-2008 20:26
idiot
Posts: And do not try?
2177 R8 - from datasheet.
SV 20-09-2008 17:46
Party
Posts: Rottor, Buy AshErovsky probe for lamps and half of the problem will be solved. His
623 name TL1040
Penultimate wise idea about "classic Chimay" was nedovyskazana thee here:
http://monitor.net.ru/forum/viewtopic.php?p=1637700#1637700
In this topic you decided to pay his part in what capacity?
SV 21-09-2008 5:00
Party
Posts: Rottor wrote:
623
You mean this: http://www.classic-music.ru/images/buben.jpg
Alexander, well, what are your ambitions ?! I do not ditch your ass on the role of the
pros theorist, I have enough of a modest share of the practice. What I was wrong in
the subject to which you refer ?! That there had to be dovyskazat? Share Marozik
from scratch principles of SMPS?
On this subject: I see no reason roughened protection. Faulty section is defined in 15
seconds. If you wish, you can unsolder the diodes and see where the smoke goes, but
it's easier to check and replace the faulty piece of metal
Rottor 21-09-2008 7:11
Guest
87.69. *. SV wrote:
*
- On this topic: I see no reason roughened protection. - Faulty section is
defined in 15 seconds.
- It's your business, but nothing to do with this topic it has not.
- About the pros and "15 Seconds norms" for the repair of inverters, I heard on that
forum.
This circumvention of protection that disable and not desirable in the case of other
faults.
What does the easiest, though conducted experiments to unmount Polevikov and
diode arrays, also helped.
Rottor 21-09-2008 20:57
Guest
87.69. *. Shafts Jura wrote:
*
This bypass protection ...
What does the easiest, though conducted experiments
I quite tactfully hinted at doubts about the wisdom of your "options", and you finally
razchirikalsya in his own confidence ...
In general, as follows:
For lamer as possible and ride at the level of confidence in your post.
However, the amplitudes at the points A and B are summed at point C.
This means that you TRANDISH.
This scheme works only on exceeding a threshold amplitude of the output voltage of
the transformer which is controlled by the growth of the bus voltage protection at the
point C.
This happens only when the (fault) lamps, or PWM output in "dressing".
VTS control scheme does not determine the amplitude and does not protect.
- That is, when you remove the transformer (at your option) do not need to make any
changes, jumpers, and beats the drum ...
- While waiting - Monday will be asked to radical solution to bypass the protection.
Shafts 21-09-2008 23:44
Jura
Party Rottor, understand that we are talking about different things.
Posts: No inverter circuits Philips (in nature), so that the example shown on your circuit.
593 Scheme there is much more fancy, so just connect the points A, B and C can not.
There when watering trance protection trips, which we bypassed by applying a signal
from the sensor working on the sensor with no trans.
Here the idea is important, and not binding to a particular scheme. Especially
not write that it is a panacea for everything.
Rottor 22-09-2008 8:57
Guest
89,138. You're not the first one.
*. * First, "all turned off clear and simple"
Then specifies certain "conditions" and calls for reflection, after which it becomes
Nichrome unclear and is not even clear what it was?
Shafts Jura wrote:
Here the idea is important, and not binding to a particular scheme.
If there is no specific, proven solutions that better then not to participate with
oboobschayuschimi projests.
Profess 31-10-2008 20:19
or
Nimnul In Elenbergah did: killed trans (determined masterkitom, and even visually) threw,
Warnin threw a lamp connected to it. Zaparallelival folded lamp socket with neighboring
gs: 1 (conclusions of the same name), and so betrayed. Without one lamp works no worse
than with vsemi.Uvy passes only simple inverters. Toshiba, for example, so fool not
Posts: work
127
PS
For those who do not understand.
- Blocking protection disables the nominal brightness control by PWM.
- Potentiometer sets the required (constant) brightness value in the minimum values of
the current consumed by the inverter.
- As required adjustment (potentiometer) can be compensated by reducing the
intensity of the glow lamps.
mag58 03-02-2009 16:04
Noob
Posts: 5 How many volts corresponds to a non-optimal brightness?
you have written in the range of 1.2 - 3.5V upper position of the potentiometer
corresponds to your circuit 5c
As proposed, me, scheme (using a single diode) the maximum voltage at the cathode
of the diode corresponds to 2.5
This is sub-optimal brightness mode? ...))))
PS
I did not set myself for such tasks polysyllabic ,, brightness mode resulting from such
"modernization" and gave me quite the same client ..
Well, you and the cards in your hand, it is possible to figure out what is more perfect
in the schematic and share the results with us.
KRAB 21-04-2009 1:17
monitor
.net.ru Removing protection for BIT3193:
When the protection is activated the voltage at terminal 5 of about 3, 5 V.
Posts: When the voltage on pin 5, from 0.4 to 2.4V, and the command "start" PWM operates
14071 autonomously, the lamp does not turn off.
Option - 1
Through a resistor 2 - 3 com pin 5 is connected to terminal 12 chips thus keep
"working" potential of about 1.2 V.
Option - 2
LED as stabistorov connected to pin 5 to ground-Live, "stabilizes" the voltage at
terminal 5 to 06 - 08 volts.
Unprotect TL1451:
- Blocking protection chip TL1451 (analogue VA9741) is reduced to a simple action-
circuiting the terminals 15 on the "ground".
But if you do it after a trip (eg forceps), then nothing happens because the trigger
protection is already locked by feedback sensors.
- To restore the performance you need to reset the trigger protection switching off and
on the inverter or a change in the level on pin 9 of the chip.
In operating mode, the monitor reset trigger protection is automatically updated.
Can not, as needed. Jura, the idea is correct. But you do not specify a very important
fact. Signal from
"Working" sensor to not "working" to be transmitted
no drawdown on this ill-fated resistor.
For other circuit solutions is paramount.
Vladimi 14-05-2009 14:29
r1234
Banned And what if all the sensors and so joined together? There is a TV Techno TS-LCD-
3225, there should LX1692. Is it possible to somehow cheat? Found that cheat
Posts: protection can be disabled 14 foot chip on the circuit ... This datasheet:
405
Posts: ( http://pdf1.alldatasheet.com/datasheet-pdf/view/226913/ETC/OZ964.html )
14071
On pin 4 (SST - Soft-Start Time) at the moment when you need to keep the 1,8 - 2V.
Connect as stabistorov red LED, apply voltage across the resistor 5.1 ohms from the
source 8 - 12V.
The chain of resistors and LEDs connected to the IC PWM constant.
Posts: Entered Monitor Packard Bell Callisto 170-700P (on the metal casing has a sticker
14071 Samsung-171) - according to the search, he is close to Xerox XA7-17i 700P and
Fujitsu-Siemens 700P.
An autopsy showed that the Lamp, "glass" and "plowed" UPS + inverter board (worth
"bug» (F2 - 3,15 A) circuit power inverter + 14V, payany inverter transistors labeled
3055). Inverter combined with UPS - PCB marking MIRAGE ELECTRONIKS AD-
1700 REV: F. (photo borrowed on the forum). IMS Inverter - TL494 (TEXAS
INSTRUMENT) in a planar design, analogs IR3M02 (SHARP), iA494
(FAIRCHILD), KA7500 (SAMSUNG), MV3759 (FUJITSU), KR1114EU4 (CIS).
Restoring and UPS connection - appears when you turn on the backlight, the picture
and after a few seconds strong heating transistors and burnout "bugs" because of the
large current.
With the help of an external inverter from the TV were immediately were checked all
4 lamps. Transistors 3055 (not vypaivaya) Call faulty.
Autonomous power inverter (backlight) is operated by the withdrawal of BL ON
connector logical "1" (with the + 5V power supply through a resistor 1k).
For rapid diagnosis Framed KT819, KT829A then - the situation has not changed -
overheating, high current consumption. Just specify that misled found in search (by
line monitor and labeling of transistor inverter) theme http://monitor.net.ru/forum/nec-
17-lh17m-ncl-1716-ph-b0-info-184746. HT ... (description of the defect 1: 1) because
it was not the wrong type transistors mje3055 (bipolar npn). Here is the snippet:
Tarkus wrote:
I write in this topic, because the problem with the exact same board, but not
in the power supply and the inverter. Monitor Packard Bell Callisto 190
(model 900P).
Inverter TL494, with a bunch of discrete binding. Attempts to find a scheme
failed, I will draw.
2 burned transistor key mje3055 and fuse on power inverter 3A, replaced;
keys very heated, worked for 5-7 seconds, and then the fuse blows. I
powered inverter undervoltage current limit, I see that after the TL494
voltage sags heavily on reservoirs key ring, on the outputs of 494 small ugly
impulses (power m / c falls to 5-6V).
Question as to whether the case in the transformer (s)? Inductance coils took
it, both trans and the same non-zero. Maybe someone has such a scheme?
For his "lock" sufficient additional solder resistor 10k between disabled (in
practice - and you can not disable) 2 terminal (inverting input of the error
amplifier) IC TL494 and connected together pin 13 (mode) and 14 (reference DC
voltage of + 5V ) - see Fig..
In the circuit of the inverter output TL494 is included in the circuit with common
collector - external load connected to the emitter of the transistor (pins 9 and 10) and
the output pulses, "sent" in this case, emissions up (rising edge of the positive) - see
Fig. IC and description. After that, when you start off the inverter were removed
ostsillogramy - at pin 5 sawtooth voltage amplitude about 3V, at the terminals 9, 10 -
square wave amplitude 11V, on the "B" output keys - similar impulses. Immediately
there was a question about the "correctness of determining the type of transistor keys"
and "title" conclusions transistors GDS.
The efficiency of each transformer was quickly checked in turn connected to the
inverter board (with a blocked protection) its primary winding remote mounting. On
the secondary side is simply connected lamp that has long been used to verify that the
inverters TFT TV (see. Photo).
For reference: the resistance of the secondary windings of transformers inverter about
360 ohms when checking "Tester fault-turns" (Master-KIT) primaries - all LEDs,
secondary - only 2-3 (mistakenly diagnoses), but a shorted secondary and primary
testing - immediately shows the presence of faults.
After the restoration of installation and protection release - monitor works OK.
For information:
1. Details of the TL494 IC can be read here: http://qrx.narod.ru/book/at/ ,
http://gauss2k.narod.ru/jab/ims02.htm .
2. If repair is necessary to "finalize" PP + UPS inverter - break ferrite tube, put on the
wire that connects the "earth" UPS "ground" of the inverter:
http://www.monitorlab.ru/forum/viewtopic.php?t = 13513 & Highlight = ad1 ... ("Do
not believe the ferrite on the wire dressed !!!"),
http://monitor.espec.ws/section3/topic85665.html - otherwise possible loss of the
backlight is switched on.
3. To reduce the ripple in the power circuit of the inverter + 14V additionally installed
capacitor 2200.0 uF.
4. Without signal (PC connection) after turning on the monitor is included in the PP,
the message "No Signal" on and off (the indicator changes color from blue to glow
yellow, lights turned off).
5. Topics with mention of the PP + UPS inverter transistors keys, etc.
http://monitor.net.ru/forum/monitors-mag-lt716s-2-info-227783.html
http://monitor.net.ru/forum/tft-proview-700p-ma782k-info-181428.html
http://monitor.net.ru/forum/viewtopic.php?t=293391
http://monitor.net.ru/forum/lcd-tv-premiera-rtr-750zx-info-180261.html
flach 10-10-2009 7:13
Party
Posts: KRAB, thank you tried the method described, the removal of protection for OZ964,
43 happened only want to add that the faulty transformer had to be removed at all,
otherwise the-counter does not work
gusek, By the way, can and clay obvyazke. SchA try to find a topic.
gusek 21-02-2010 16:53
Party
Posts: andros, lamp tested on another inverter - is working properly.
1754 Yes, and I tossed the other transformer, though a bit not the same as home, but still
think it should have been run, but will not start.
Sam is now mudohayus one such. It is not yet won. The problem is that all
rabotaet.Esli turn on the cold can work out an hour or two and then goes out, and
maybe 15-20 minutes go out. With the heating of the work is reduced. Lamps tested
on another monitor, electrolytes polls all replaced, ferrite on peremyke weight lifted.
Diode Arrays at 5 and 14 volts replaced just in case. Please highlight force. Drove.
Found that after a while the output 14B appears shit and slightly squander voltage (up
to 13V). Thus from TPI itching with slightly varying tone. Lamp while continuing to
burn properly, nothing is overheating protection does not work. In general while in the
process ... the result will accomplish your goal.
Here's something for the backlight inverter circuitry from the Chinese.
Posts: Or immediately after the lights will flicker and disappear (logo visible) or can work
14071 for 5-10 minutes and switch off, spontaneous trip and simply non-functional
backlight.
Lamps are OK (new - predtorgah, checked), the inverter photo - below. Apparently it
is not designed for this power of lamps: overheating of transformers during normal
operation in the healthy new TV more than 65-70 degrees. With sealed transformer
(defective, but the secondary resistance is 1: 1 with intact - just trying to live) - the
inverter will not start.
To lock protection enough solder resistor 1 MOhm with 12 Volt (power inverter)
15 concluded TL494.
After that can be installed as other non-original transformer (see. Photo - left, set to
test), and his failure to use and easy to connect only 2 backlights (the image has
virtually no effect - from the words of the wholesaler - he did not notice).
DK 25-07-2010 20:52
Warnin
gs: 1 Valentin wrote:
a well-known ... 123rd block on 1yu FAN7314 set foot on the 4.3v zener
Posts:
with + 5V and 620 ohm resistor on the body.
198
and inverter BN44-000123E Model: SIP-U5F (M) with a defective trance The
Samsung 940N.
Troubleshooting for the secondary blocked FAN7314 protection even easier,
gave her the first leg of 1.5 volts AA batteries with two wires
maxxpr 03-09-2010 22:53
off
Noob DK wrote:
Posts: 5
Valentin wrote:
a well-known ... 123rd block on 1yu FAN7314 set foot on the 4.3v
zener with + 5V and 620 ohm resistor on the body.
gave her the first leg of 1.5 volts AA batteries with two wires
Even easier to solder to the 1st leg of the LED-Live to the ground.
It will operate in stabistorov.
This method is described respected KRAB on the 2nd page of this topic, see the
removal of protection for BIT3193
Personally tested this method on the above inverter BN44-000123E Model: SIP-U5F
(M) with a broken vtorichkoy- protection does not work
NASER 16-10-2010 18:27
AT
Guest SKI across multiple PWM DT8211. Protection bypass resistor decrease by 8 foot.
92.46. *. Instead of 200 ohms set 10-20 ohms.
*
Posts: Predtorgah. When you turn on the backlight or not, or wink on and off. Lamps are
14071 OK.
Disabling protection similar to: http://monitor.net.ru/forum/viewtopic.php?
t=239071&start=64#256061 ...
To lock protection enough solder resistor 1 MOhm with 12 Volt (power inverter)
15 concluded TL494.
working
AMIT wrote:
... Put LED ...
prametrom close to 20 mA
ra4llb 13-01-2011 9:35
Warnin
gs: 1 oz960 --- kiloomnikom not blocked, but the battery to 1.5V through a resistor 10th
plus the housing easily (the battery is connected to the first leg)
Posts:
239
AMIT wrote:
0Z960
very easy way to remove the protection.
supply LED C10 feet on the ground. (6 foot chip)
mladshi 17-01-2011 18:39
Party
Posts: AMIT, That'S Perfect !!!
572
"0Z960
very easy way to remove the protection.
supply LED C10 feet on the ground. (6 foot chip) "
perfect solution, it is worth 20 "Samsung (matrix AUO) other 4-5 years ago, when the
go out after a few seconds, the inverter 6 lamps
If you turn once working days. (Blame lamps all at once, to understand posmotrel- all
equally with the lights worked Hilo manage resource, tossed 20 "AUO wide by Sonke
- everything is OK)
connected svetodiod- glow when on the move to disable one of the lamps is turned
off, and if one of the bulbs that will not turn off that gud, the main defect is gone,
pomotrite how long stretch.
artur58 09-02-2011 16:37
Party
Posts: Erisson 26LS16, THOMSON 26N90NH10 power unit MIP260
114 Combined power supply and inverter. Composition: L6562 - preconditioner,
SG3525AN and board submodule F9222 - Inverter
Posts:
14071
X1-42 13-04-2011 16:56
Party
Posts: POLAR 38LTV4105 inverter and power supply on the same board - PLT-055. BP on
40 the TDA1506 + field.
Inverter chip UBA2071AT + two field STP60N06.
Forced into submission grounding pin 5 of the chip.
Forced the search for protection when the method of replacing the board found out
that she does not like the lamp.
PS: for the interest rechecked just that, but in a different inverter FAN7314 to a
"locked" protection - all regulated without problems.
Piramid 31-07-2011 15:50
on
Party KRAB,
Posts: Ok!
401 Not everywhere can still adjust the brightness after the lockout protection, I do not
know how in your case BUT
- The fact that in addition to disabling the protection you need to seek the ability to
adjust the brightness of the lamps.
A simple crafts, proposed by some authors do not provide such an opportunity that
leads to increased brightness and rapid deterioration of lamps.
Therefore, I have at least once warned about it, but the findings seem nobody does.
Rottor wrote:
mag58 wrote:
- I made and its contribution to the debate))
- Monitor starts, earned lights and turn off most.
PS
For those who do not understand.
- Blocking protection disables the nominal brightness control by PWM.
- Potentiometer sets the required (constant) brightness value in the minimum
values of the current consumed by the inverter.
- As required adjustment (potentiometer) can be compensated by reducing the intensity of
the glow lamps.
Option - 1
Through a resistor 2 - 3 com pin 5 is connected to terminal 12 chips thus keep
"working" potential of about 1.2 V.
Option - 2
LED as stabistorov connected to pin 5 to ground-Live, "stabilizes" the voltage at
terminal 5 to 06 - 08 volts
http://www.datasheetdir.com/FAN7314A+CCFL-Controllers
Capacitor need to pick up, comparing swings in the return signals converted winding
and working. In my case it turned out to 3300p.
By the way, about this method, I have never read. Although, maybe just not in sight.
PS All collected on the "knee", so to speak experimental option. Client drove off for
two weeks, so it was time "to dig". TV has been working for a week. Tomorrow will
bring all in divine form, and you may start to give.
evg4682 01-03-2012 19:47
Noob
Posts: Controller QZ 9910 GN protection is turned off: LED with 3 feet stabistorov. Works
12 with one lamp, regulated only contrast. Monitor Aser al1716.
BD9883 PDF
SHARP INVERTER RUNTKA396WJGZ BD9883FV jumper C7528 - Off
zaschity.pdf 193.65 KB Downloaded: 1769 time (s)
It does not help. Can anyone have a way to remove the protection from this
Shima?
Silver63, do not ask questions here! But since you drew - then davayka and work
hard.
That's shit on the DT8211 - http://bbs.dianyuan.com/bbs/u/70/93971224214839.pdf
On page 9 you will find Protection (OLP, SCP). Moved machine -
Quote:
Protection (OLP, SCP)
An abnormal state is determined by the level of IFB. If IFB level is reduced
less than 0.75V DT8211 engaged in protection mode. This mode means that
one or more feedback current levels are very low. To switch to normal mode
IFB level should be higher than 0.75V. In the protection of the capacitor,
which is connected with the output PROT charged to 0.5uA. If the level is
on track PROT is a 3.0V DT8211 outputs are disabled. To resume work
after disconnecting DT8211, EN or VCC must move from a low to a high
level. Protection time is determined as shown below by the formula .....
In my case it was stuck the first available under the arm trance with secondary
resistance 1.1K (native trances 2.2K) in parallel dead obmotki.Pervichka was
connected so as not to parallel.Rodnoy trans desoldering (one coil because live)
.Amplitudy buildup turned enough for two windings of primary parallelno.Nikakih
blackouts are not visible.
gosha_g 28-06-2012 15:20
or
Noob Deprotection of the inverter IC type MSC6512CPW ---- put resistance 10k + 12V
Posts: 2 LED series 5-pin chip, which is equal to 1.2 volts. Works OK ...
Deprotection of the inverter IC type LX1691A: Dana 14 foot chip called as OP-SNS
is grounded on the case. Works OK.
Benzopi 09-07-2012 9:02
ren
Banned To disable the MP1009
Short-circuit pin 5 on the body.
Posts:
52
bdvrt 30-07-2012 14:00
Warnin
gs: 1 OZT1060GN - sv.diod pin1
MOSFET Drivers
Light Sensors
Posts:
5830 BIT3713 PDF
Posts:
239
BA9741 PDF
Posts:
340
Posts:
340
Posts:
340
PS
For those who do not understand.
- Blocking protection disables the nominal brightness control by PWM.
- Potentiometer sets the required (constant) brightness value in the minimum
values of the current consumed by the inverter.
- As required adjustment (potentiometer) can be compensated by reducing
the intensity of the glow lamps.
Got LCD 37 ", one I / O section of the trance is broken, there is no backlight.
Inverter for OZ964, trans redkiy- inductance 1,36N / 0,17mN.
I had to return the damaged trans (per lamp works), the adjacent lamp hung trans-
donor in parallel.
Inductance coils donor below- very different. Redirect to both halves of the donor
sequence to bring the options to work.
Screen light evenly, perhaps one of the bulbs (the donor) is weaker, but not much.
Protection remains nominal, backlight adjustable.
ABDU 05/01/2013 13:42
Party
Posts: FAN7313 shutdown protection - c 17 pin IC LED to ground.
158
Posts: 4 pin - C_TO - Time Out set capacitor LX1692 - close to the ground.
5830
roman7 20.06.2013 8:15
97
Guest BD9893 - disable protection can be planted on the ground pin 10 (scp) tested 100
95.32. *. percent, but the guys are not a panacea but only a method of searching for real cause
* of the problem!
Posts:
16
Large size
Iskande 18/11/2014 11:35
r
Warnin UBA2074 to unprotect - 20kOm on housing with O 6. (6pin - CT - fault timing
gs: 1 capacitor)
Posts:
22
In the beginning there is background noise, a few seconds after the lamp is fully lit
and operating correctly.
As it turned out - "noisy" high-voltage (3kV) capacitor that after several restarts his
way - probably not work 2 lamps.
Posts:
4251
Posts:
108