Professional Documents
Culture Documents
TYPE 8B1/8B1T: Elastomer O-Ring Seals
TYPE 8B1/8B1T: Elastomer O-Ring Seals
TYPE 8B1/8B1T
Elastomer O-Ring Seals
A – Face/Primary Ring
B – Seat/Mating Ring
C – Spring
D – O-Ring
E – Disc
F – Anti-X Ring H
G – Retainer C
E
H – Set Screws I
F
I – Snap Ring
D
G
D
A
B
16-32µ" 0.040"
MIN.
D4
D3 L9 L65
MIN.
SEAL OD
D2 BORE
L3 D1
± 0.002" ±0.031" W. H. ± 0.002" 20˚
For ease of installation, the lead-in
edge of shaft or sleeve should be
chamfered as shown.
16-32µ" 0.040"
MIN.
D4
D3 L9 L65
MIN.
SEAL OD
D2 BORE
L3 D1
± 0.002" ±0.031" W. H. ± 0.002" 20˚
For ease of installation, the lead-in
edge of shaft or sleeve should be
chamfered as shown.
400 27.6
Seal Size
The Basic Pressure Rating is for a standard Type 8B1 or 8B1T seal, as shown in the typical arrangement, when installed according
to the criteria given in this data sheet and generally accepted industrial practices.
The Basic Pressure Rating assumes stable operation at 3600 rpm in a clean, cool, lubricating, nonvolatile liquid, with an adequate
flush rate. When used with the Multiplier Factors, the Basic Pressure Rating can be adjusted to provide a conservative estimate
of the dynamic pressure rating. For process services outside this range or a more precise assessment of the dynamic pressure
rating, contact John Crane for more information.
Multiplier Factors
Example for Determining Pressure Rating Limits
Multiplier
Selection Considerations Factor Seal: 50mm/2" diameter Type 8B1
Product: Water
Speed 3600 rpm x 1.00
Face Material: Carbon vs. Silicon Carbide
Above 3600 rpm* **
Temperature: 16°C/60°F
Sealed Fluid Petrol/Gasoline, Kerosene, or better x 1.00 Speed: 1800 rpm
Lubricity Water and Aqueous Solutions x 0.75 Using the Basic Pressure Rating chart, the
Flashing Hydrocarbons*** x 0.60 maximum pressure would be 76 bar g/1100 psig.
(Specific Gravity ≤.65)
From the Multiplier Factors chart, apply the
multipliers for the specific service requirements to
Sealed Fluid Below 80°C/175°F x 1.00
determine the maximum operating pressure for
Temperature From 80°C to 125°C/175°F to 250°F x 0.90
the application.
(for carbon From 125°C to 180°C/250°F to 350°F x 0.80
only) Above 180°C/350°F x 0.65 76 bar g/1100 psig x 1.00 x 0.75 x 1.00 =
825 psig/57 bar g.
* Not to exceed 25m/s/5000 fpm. At 3600 rpm with the service conditions noted,
a 50mm/2" diameter Type 8B1 Seal has a
** Multiplier = 3600/new speed
Example: If new speed = 4000 rpm maximum operating limit of 825 psig/57 bar g.
Multiplier = 3600/4000 = 0.90 If operating pressure exceeds the pressure limit,
consult John Crane.
*** The ratio of sealed pressure to vapor pressure must be greater than 1.5,
otherwise consult John Crane. If the specific gravity is less than 0.60,
consult John Crane.
TYPE 8B1/8B1T
Elastomer O-Ring Seals
2500 172
2000 138
Type 8B1 Carbon
1500 103
1000 69
500 35
CUT LINE FOR SHORT PAGE
0 0
0 1 2 3 4 5 6 (inches)
Materials of Construction
©2004 John Crane Inc. Print 7/04 www.johncrane.com ISO 9001, ISO 14001, ISO/TS 16949 Certified. S-8B1/8B1T