Professional Documents
Culture Documents
Sae Ams 5520G-2015
Sae Ams 5520G-2015
1 .1 Form
This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, foil, and plate.
1 .2 Application
These produ cts have been used typically for parts req uiring corrosion resistance and high strength u p to 600 °F (31 6 °C)
and where su ch parts may req uire welding during fabrication, but usage is not limited to su ch applications.
1 . 2. 1 Certain d esign and processing procedu res may cause these prod ucts to become susceptible to stress-corrosion
cracking; ARP1 1 1 0 recommends practices to minimize such conditions.
The issue of the following documents in effect on the date of the pu rchase order forms a part of this specification to the
extent supplied herein. The supplier may work to a su bseq uent revision of a docu ment unless a specific document issu e
is specified . When the referenced d ocu ment has been cancelled and no supersed ing d ocument has been specified , the
last pu blished issue of that document shall apply.
2. 1 SAE Publications
Available from SAE I n tern ati on al , 400 Com m on weal th D ri ve, Warren d al e, PA 1 5096-0 001 , Tel : 877-60 6-732 3 (i n si d e
U S A an d Can ad a) or 72 4-776-4970 (ou tsi d e U S A), www. sae. org .
AM S2242 Tolerances, Corrosion and H eat-Resistant Steel, I ron Alloy, Titanium, and Titanium Alloy Sheet, Strip,
and Plate
AM S2248 Chemical Check Analysis Limits, Corrosion and H eat-Resistant Steels and Alloys, M araging and Other
H ighly-Alloyed Steels, and I ron Alloys
AM S2371 Quality Assurance Sampling and Testing, Corrosion and H eat-Resistant Steels and Alloys, Wrou ght
Prod ucts and Forging Stock
AM S2807 I dentification, Carbon and Low-Alloy Steels, Corrosion and H eat-Resistant Steels and Alloys, Sheet,
Strip, Plate, and Aircraft Tubing
(Continued)
__________________________________________________________________________________________________________________________________________
SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is
entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”
SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and
suggestions.
Copyright © 201 5 SAE International
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SAE.
TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) SAE values your input. To provide feedback
Tel: +1 724-776-4970 (outside USA) on this Technical Report, please visit
Fax: 724-776-0790 http://www.sae.org/technical/standards/AMS5520G
Email: CustomerService@sae.org
SAE WEB ADDRESS: http://www.sae.org
SAE INTERNATIONAL AMS5520G Page 2 of 7
_________________________________________________________________________________________________
2. 2 ASTM Publications
Avai l abl e from ASTM I n tern ati on al , 1 00 Barr H arbor Dri ve, P. O. Box C700, West Con sh oh ocken , PA 1 9428-2959,
Tel : 61 0-832-9585, www. astm . org .
3. 1 Composition
Shall conform to the percentages by weight shown in Table 1 , d etermined by wet chemical methods in accordance with
ASTM E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser.
TABLE 1 - COMPOSI TI ON
Element min max
Carbon -- 0. 09
M anganese -- 1 . 00
Silicon -- 1 . 00
Phosphorus -- 0. 040
Su lfur -- 0. 030
Chromium 1 4. 00 1 6. 00
N ickel 6. 50 7. 75
M olybd enum 2. 00 3. 00
Aluminum 0. 75 1 . 50
3. 1 . 1 Check Analysis
3. 2 Cond ition
Cold rolled , solution heat treated, and, u nless solution heat treatment is performed in an atmosphere yield ing a bright
finish, descaled having a su rface appearance comparable to the following commercial corrosion-resistant steel finishes as
described in ASTM A 480/A 480M and AS41 94, and 3. 2. 1 . 1 or 3. 2. 1 . 2 as applicable.
3. 2. 1 . 1 Sheet
N o. 2D finish.
SAE INTERNATIONAL AMS5520G Page 3 of 7
_________________________________________________________________________________________________
3. 2. 1 . 2 Strip
N o. 1 strip finish.
3. 2. 2 Plate
The product shall be solution heat treated by heating to a temperature within the range 1 925 to 1 975 °F (1 052 to 1 079 °C),
holding at the selected temperature for a time commensurate with thickness and the heating equipment and procedure used,
and cooling at a rate equivalent to an air cool or faster.
3. 4 Properties
Product 0. 001 5 inch (0. 038 mm) and over in nominal thickness shall conform to the following requirements. Tensile and
hard ness testing shall be performed in accord ance with ASTM A 370.
3. 4. 1 . 1 Tensile Properties
3. 4. 1 . 2 H ardness
Shall be not higher than 1 00 H RB, or equivalent (See 8. 2); for thin gages where su perficial hard ness testing is
impractical, microhard ness testing in accord ance with ASTM E 384 may be used . Product shall not be rejected on the
basis of hardness if the tensile properties of 3. 4. 1 . 1 are acceptable, determined on specimens taken from the same
sample as that with nonconforming hardness or from another sample with similar nonconforming hardness.
SAE INTERNATIONAL AMS5520G Page 4 of 7
_________________________________________________________________________________________________
3. 4. 1 . 3 Bending
Product shall be tested in accordance with ASTM E 290, using a sample prepared nominally 0. 75 inch (1 9. 0 mm) in width,
with the axis of bending parallel to the direction of rolling, and shall withstand, without cracking, when bending at room
temperature through the angle shown in Table 3 around a d iameter eq ual to the bend factor times the nominal thickness
of the product. I n case of dispute, the results of tests using the guided bend test of ASTM E 290 shall govern.
The prod uct shall have the following properties after being au stenite conditioned by heating to 1 400 °F ± 25 (760 °C
± 1 4), holding at heat for 90 minutes ± 5, cooling to 55 °F ± 5 (1 3 °C ± 3) within 60 minutes, holding at that temperature for
not less than 30 minutes, and precipitation heat treated by heating to 1 050 °F ± 1 0 (566 °C ± 6), hold ing at heat for
90 minutes ± 5, and cooling to room temperature:
3. 4. 2. 1 Tensile Properties
3. 4. 2. 2 H ardness
Shall be not lower than 40 H RC, or equ ivalent (See 8. 2); for thin gages where superficial hardness testing is impractical,
microhardness testing in accordance with ASTM E 384 may be u sed. Product shall not be rejected on the basis of
hard ness if the tensile properties of 3. 4. 2. 1 are acceptable, determined on specimens taken from the same sample as
that with nonconforming hardness or from another sample with similar nonconforming hardness.
SAE INTERNATIONAL AMS5520G Page 5 of 7
_________________________________________________________________________________________________
The product shall have the following properties after being austenite conditioned by heating to 1 750 °F ± 25 (954 °C ± 1 4),
holding at heat for not less than 1 0 minutes, rapidly cooling to room temperature, sub-zero transformed by cooling to -1 00 °F
± 1 0 (-73 °C ± 6), holding at that temperature for not less than 8 hours, warming in air to room temperature, and precipitation
heat treated by heating to 950 °F ± 1 0 (51 0 °C ± 6), holding at heat for 60 minutes ± 5, and cooling to room temperature:
3. 4. 3. 1 Tensile Properties
3. 4. 3. 2 H ardness
Shall be not lower than 45 H RC, or equ ivalent (See 8. 2); for thin gages where superficial hardness testing is impractical,
microhardness testing in accordance with ASTM E 384 may be u sed. Product shall not be rejected on the basis of
hard ness if the tensile properties of 3. 4. 3. 1 are acceptable, determined on specimens taken from the same sample as
that with nonconforming hardness or from another sample with similar nonconforming hardness.
3. 5 Qu ality
The produ ct, as received by purchaser, shall be uniform in quality and cond ition, sound, and free from foreign materials
and from imperfections detrimental to usage of the prod uct.
3. 6 Tolerances
The vendor of the produ ct shall supply all samples for vendor’s tests and shall be responsible for the performance of all
requ ired tests. Purchaser reserves the right to sample and to perform any confirmatory testing d eemed necessary to
ensure that the prod uct conforms to specified req uirements.
SAE INTERNATIONAL AMS5520G Page 6 of 7
_________________________________________________________________________________________________
4. 2 Classification of Tests
4. 2. 1 Acceptance Tests
Composition (3. 1 ), tensile properties as solution heat treated (3. 4. 1 . 1 ) and as au stenite conditioned and precipitation heat
treated (3. 4. 2. 1 ), and tolerances (3. 6) are acceptance tests and shall be performed on each heat or lot as applicable.
4. 2. 2 Period ic Tests
Bending as solution heat treated (3. 4. 1 . 3), hardness (3. 4. 1 . 2, 3. 4. 2. 2, and 3. 4. 3. 2), and tensile properties as austenite
conditioned, sub-zero transformed, and precipitation heat treated (3. 4. 3. 1 ) are periodic tests and shall be performed at a
freq uency selected by the vendor unless frequency of testing is specified by pu rchaser.
4. 4 Reports
The vendor of the prod uct shall fu rnish with each shipment a report showing the results of tests for composition of each
heat and for tensile properties of each lot as solution heat treated and as au stenite cond itioned and precipitation heat
treated , and stating that the produ ct conforms to the other technical requ irements. This report shall include the purchase
order number, heat and lot numbers, AM S5520G, size, and qu antity.
5. 1 I dentification
5. 2 Packaging
The product shall be prepared for shipment in accordance wi th commercial practice and in compliance with applicable
rules and regulations pertaining to the handling, packaging, and transportation of the product to ensu re carrier acceptance
and safe delivery.
6. ACKN OWLEDGM EN T
A vendor shall mention this specification nu mber and its revision letter in all quotations and when acknowled ging
pu rchase orders.
7. REJ ECTI ON S
Product not conforming to this specification, or to modifi cations authorized by purchaser, will be subject to rejection.
8. N OTES
8. 1 A change bar (| ) located in the left margin is for the convenience of the user in locating areas where technical
revisions, not editorial changes, have been made to the previous issu e of a docu ment. An (R) symbol to the left of
the docu ment title ind icates a complete revision of the docu ment, includ ing technical revision. Change bars and (R)
are not u sed in original publications, nor in d ocuments that contain ed itorial changes only.
8. 4 Dimensions and properties in inch/pound u nits and the Fahrenheit temperatures are primary; d imensions and
properties in SI u nits and the Celsiu s temperatures are shown as the approximate equ ivalents of the primary units
and are presented only for information.
AM S5520G
Form and size of prod uct desired
Qu antity of produ ct desired.