Professional Documents
Culture Documents
TRUTH TABLE
INPUT OUTPUT
G An Yn
L L L
L H H
H X Z
X:”H” or ”L”
Z: High impedance
2/8
74VHC244
DC SPECIFICATIONS
Symb ol Parameter T est Cond ition s Value Un it
V CC T A = 25 o C -40 to 85 o C
(V) Min. Typ . Max. Min . Max.
VIH High Level Input 2.0 1.5 1.5
V
Voltage 3.0 to 5.5 0.7VCC 0.7VCC
VIL Low Level Input 2.0 0.5 0.5
V
Voltage 3.0 to 5.5 0.3VCC 0.3VCC
VOH High Level Output 2.0 IO=-50 µA 1.9 2.0 1.9
Voltage 3.0 IO=-50 µA 2.9 3.0 2.9
V
4.5 IO=-50 µA 4.4 4.5 4.4
3.0 IO=-4 mA 2.58 2.48
4.5 IO=-8 mA 3.94 3.8
VOL Low Level Output 2.0 IO=50 µA 0.0 0.1 0.1
Voltage 3.0 IO=50 µA 0.0 0.1 0.1
V
4.5 IO=50 µA 0.0 0.1 0.1
3.0 IO=4 mA 0.36 0.44
4.5 IO=8 mA 0.36 0.44
IOZ High Impedance VI = VIH orVIL ±0.25 ±2.5 µA
Output Leakage 5.5 VO = VCC orGND
Current
II Input Leakage Current 0 to 5.5 VI = 5.5V or GND ±0.1 ±1.0 µA
ICC Quiescent Supply 5.5 VI = VCC orGND 4 40 µA
Current
3/8
74VHC244
CAPACITIVE CHARACTERISTICS
Symb ol Parameter T est Cond ition s Value Un it
T A = 25 o C -40 to 85 o C
Min. Typ . Max. Min . Max.
CIN Input Capacitance 4 10 10 pF
COUT Output Capacitance 6 pF
CPD Power Dissipation 19 pF
Capacitance (note 1)
1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto
Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/48(per Gate)
TEST CIRCUIT
T EST SW IT CH
tPLH , tPHL Open
tPZL , tPLZ VCC
tPZH , tPHZ GND
CL = 15/50 pF or equivalent (includes jig and probe capacitance)
RL = R1 = 1KΩ orequivalent
RT = ZOUT of pulse generator (typically 50Ω)
4/8
74VHC244
WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle)
5/8
74VHC244
mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 2.65 0.104
a1 0.10 0.20 0.004 0.007
a2 2.45 0.096
b 0.35 0.49 0.013 0.019
b1 0.23 0.32 0.009 0.012
C 0.50 0.020
c1 45 (typ.)
D 12.60 13.00 0.496 0.512
E 10.00 10.65 0.393 0.419
e 1.27 0.050
e3 11.43 0.450
F 7.40 7.60 0.291 0.299
L 0.50 1.27 0.19 0.050
M 0.75 0.029
S 8 (max.)
P013L
6/8
74VHC244
mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.1 0.433
K 0o 4o 8o 0o 4o 8o
A A2
K L
A1 b e
c E
E1
PIN 1 IDENTIFICATION
1
7/8
74VHC244
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a trademark of STMicroelectronics
8/8
This datasheet has been downloaded from:
www.DatasheetCatalog.com