Professional Documents
Culture Documents
User's Manual For Chery Riich 2 Series: Advice
User's Manual For Chery Riich 2 Series: Advice
ADVICE
Sincere congratulations on your own of one Chery Riich 2! Also, with great appreciation on your great favor on our company and our
products.
The personnel of Chery authorized service station are trained with good professional trainings, who will sincerely provide you with the top
quality service.
Chery Riich 2 features advanced technology and prominent performances. Your choice of Chery Riich 2 will prove that you have extra-hi gh
requirements on the vehicle performance and design.
Please read this manual carefully, since the information contained in this manual can let you understand how to operate and maintain your
vehicle properly so as to achieve the driving pleasure to the maximum extent.
This user’s manual applies to the Chery Riich 2.
Chery Automobile Co., Ltd.
Preface
This manual is established based on the Please make sure to read this manua l, service station.
detailed conditions of Riich 2 vehicles especially the chapter “Quality warranty Any problems of Our Company’s products
manufactured by Chery Automobile Co., service” before using this product, during use must be overhauled by the
Ltd., which only applies to the Riich 2 otherwise you may have no right to take Chery authorized service station. During
vehicles manufactured by Chery the service due to your improper usage. the overhaul process, Chery authorized
Automobile Co., Ltd.. This manual Chery Automobile Co., Ltd. (hereafter service station is entitled to decide based
includes the latest information up to the referred as “Our Company” or “Chery on the conditions to perform the repair by
date when this manual is printed. Chery Company”) defined the technical means of repair or the replacement of
Automobile Co., Ltd. will be wholly maintenance regulations of the new equivalent parts.
responsible for the modification and vehicle run in and of maintenance at If you encountered anything unclear
explanation of this manual and reserved various stages for the products, including during the careful reading of this manual,
the rights for product replacement after the the first 5,000 km maintenance. Please Chery Company and Chery authorized
print of this manual without any prior make sure to abide by the above service station will give you the detailed
notice. Some pictures in this manual are regulations since the above defined explanation. Also, the precious advices of
illustrations for reference only. The real maintenance is vital to the safety operation vast users are highly welcomed.
article should take precedence in case of and the maintaining of good running
any conflict between the pictures and the conditions of your vehicle. Chery Automobile Co., Ltd. reserved all
real articles. Your claim right will be forfeited in case copyrights of this manual
This manual is the main evidence for of the failure of your vehicle or vehicle
vehicle quality warranty. Please keep this parts arising from the abuse, negligence, Wish you pleasant driving!
manual in your vehicle so that it’s improper use, the maintenance not in
available whenever you need it. When you accordance with the specified
resell this vehicle, please hand over this mileage/period, or the warranty evidence
manual and all the do cumentation attached not signed or stamped in accordance with
with this vehicle to the new owner so that the requirements, or any unauthorized
they are available whenever the new refit/attachment. Therefore, any direct or
owner needs them. indirect warranty application thereof will
Special Statement not be accepted by the Chery authorized
Preface
Table of contents
Open Engine Bonnet ..................................65 Midd le 2-Point Safety Belt for Middle Seats 72
Remote Control System with Anti-Theft Maintenance of Seat Safety Belt ................. 72
Check seat safety belt...................................... 72
Function ( )...............................................66
Air Bag ( ) ................................................ 73
Door Lock & Unloc k ................................ 66
Front Air Bag ........................................... 73
Alarm ..................................................... 66
Air Bag Alarm Lamp ................................ 74
Remote Controller Battery Replacement ...... 67
Electronic Anti-theft System ...................... 67 Child Safety Seat........................................ 74
Seat & Safety Protection ...........................68 Chapter 5 Emergency Procedures .... 77
Seat ........................................................ 68 Hazard Warning Flasher lamp................. 78
Correct Sitting Posture .............................. 68 Electronic Control Unit Support System. 78
Adjustment of Front Seats.......................... 68 Duly Refuel ................................................. 78
Adjustment of Middle Seats ....................... 69 Replace Bulbs ............................................. 79
Adjustment of Rear Seats .......................... 69
Headlamp Unit (Including High Beam / Low
Headrest .................................................. 69
Adjusting method of headrest:....................... 69 Beam / Position / Turn Indicator Lamps) ..... 79
Removing and assembling method of headrest: Taillight Bulb ........................................... 80
........................................................................... 70 High-Mounted Braking Lamp Bulb ............ 80
Folding of Middle Seats ............................ 70 License Plate Lamp Bulb ........................... 80
Folding of Rear Seats ................................ 70 Interior Front Ceiling Lamp Bulb ............... 80
Reposition of rear seats................................... 70 Luggage Boot Lamp Bulb ......................... 81
Luggage Conveyance ................................ 71 Regulate the Beam of Headlamp ................ 81
Seat Safety Belt ..........................................71 Fuse & Relay.............................................. 81
Seat Safety Belt Alarm Lamp ..................... 71 Fuse........................................................ 81
Fastening Seat Safety Belt ......................... 72 Cartridge Fuse ......................................... 82
Preface
Chapter 1 Summary
1
Summary
Before reading this vehicle. The Chery authorized service vehicle equipment, and how to avoid the
stations all over the country boasted person injury? In this manual, the answer
User’s Manual, you numerous repair experts to provide you for such question is included in the
should understand with service anytime. The repair personnel explanation for the alarm symbols with
of all authorized service stations, who triangle. Please read carefully and abide
following things. passed the professional trainings, can by the contents thereof.
Thanks for your purchase of Chery vehicle. properly repair your vehicle and vehicle
The equipment marked with
In order to operate your vehicle properly equipment. The spare parts in Chery
asterisk (*) is only used in lot size
and guarantee your rights and benefits, authorized service station are Chery
on certain model structures, which is
please spend some time to read this genu ine spare parts.
supplied as optional equipment for some
manual carefully. models or is only available in certain
Equipment Scope
This manual provides the important This manual defined the maximum markets.
instructions and hints on the daily driving possible equipment scop e installed in When this symbol is present on
and regular maintenance and care, with the accordance with the series Riich 2 model the vehicle, make sure to read
purpose for your familiarity with the plan till the print date, namely for all the the related chapters of this manual before
operation of your vehicle. Only the more standard equipment and optional any operation.
understanding to your vehicle can equipment in series Riich 2 model, some
guarantee the safety and economy of the equipment may be supplied in the future We must contribute our
vehicle driving as well as enjoy the or may be only available in certain responsibility and liability in the
pleasure thereof. markets. Therefore, some items in this working of environmental protection.
manual may not apply to your vehicle. It’s the important step to achieve such
Any improper operation may damage your objective by operating your vehicle
vehicle as well as maybe deprive of your Alarm Symbols within This properly and disposing the used cleaning
claim right. Manual articles and lubricating materials in
The periodical maintenance to your accordance with the laws and regulations.
During the vehicle operation, pay
vehicle will help maintain the driving This manual displays the information on
attention to how to reduce the
performance and used value of your this aspect by means of tree symbol.
damage to the vehicle and the
2
Summary
New Vehicle Inspection great influence on the use lifetime, engine speed is 6000 r/min. During the
working reliability and economy of the manual gearshift, make sure to shift to the
Before delivering the vehicle to you, the
vehicle, therefore, the use of new vehicle next high gear when the engine tacho meter
dealer of Chery Company has already
must abide by the run in regulations indicator reached red indication area at the
performed the vehicle inspection in
strictly. latest.
accordance with the regulations of Chery
Automobile Co., Ltd. The dealer of Chery
Run in Regulation within 1,000 Avoid the running of engine at
Company should fill in the vehicle
km unnecessary high speed. The
delivery date in the “Vehicle Delivery
Full speed driving is absolutely earlier shift to high gear will
Inspection Certificate” column of this
prohibited; help save the fuel, reduce the working
manual and seal with the stamp of dealing
noise as well as diminish the
agency.
Generally, do not drive the vehicle at environmental pollution.
The dealer should verify the entire vehicle the speed above 100 km/h;
The engine speed should not be excessive
performance and introduce the operation
Avoid driving at the top speed at any low during driving. Shift to proper gear at
knowledge of the vehicle against the
gear. reasonable time.
“Chery Vehicle Sale & Delivery Card”
dually signed by the salesman and the
In cold engine condition, do not run the
user. Run in Regulation from 1,000 km engine at top speed on neutral gear or any
to 1,500 km other driving gear.
Run in of New Vehicle
Due to the manufacture and assembling Increase to the top speed gradually or The new tires don’t have best adhesion at
deviations, the friction resistances between drive at the allowable max. engine the beginning of use; therefore, the tires
the moving components of the new vehicle speed. also need run in. The vehicle speed should
at the initial stage of operation will be be relatively low during first 100 km
much greater than the ones in normal Notice during Run in Period driving and the driving should be
condition. The run in effects of the vehicle For the driving of vehicles with engine extremely careful.
at the initial stage of op eration will exert tachometer, the allowed short period top
3
Summary
The new brake friction lining also needs service counsel, who will provide you
run in, since the brake doesn't have ideal with be st service.
friction force during first 200 km driving.
During this period the brake effect is a
little poor, therefore the pressure on brake
pedal may be reasonably increased. Such
condition is also applicable each time it’s
replaced with new friction lining.
“One-To-One” Service
In order to provide you with better service
and vehicle use, the dealer of Chery
Company will appoint one service counsel
to serve you at the purchase of your
vehicle. In case of any problems during
your vehicle use, you may contact your
4
Summary
This is to certify that this vehicle has completed the vehicle Vehicle Owner Name (Unit) Responsible Service Station Name
delivery inspection defined by Chery Automobile Co., Ltd. and its
quality meets with the technical specification of Chery Automobile —————————————————— —————————————————————
Co., Ltd.
—————————————————— —————————————————————
Dealer Stamp:
5
Summary
Model
Transmission No.:
Engine Serial No.:
6
Summary
7
Summary
8
Summary
“One-To-One” Counseling Service Card exclusive person to communicate and contact with the user.
□ One user is only served by one service counsel: “One-To-One”
(Service Station) □ User may choose other service counsel when he dissatisfies
with current service counsel.
User Name: Vehicle Purchase Date III. M ajor job introduction of service counsel (“√ ” for Yes as “×”
for No).
Sales Agency: M odel:
□ Repair maintenance service reception
Vehicle VIN Number:
□ Complaint acceptance
□ Periodical maintenance remind ing visits
The following items should be confirmed by the user.
Related items confirmation at vehicle delivery (“√" for Yes as □ Repair/M aintenance couns el explanation
I.
□ Periodical greeting visits
□
“×” for No)
□ Repair/maintenance reservation acceptance
9
Summary
10
Summary
Engine
ABS Anti-lock brake
self-examination Position lamp
system
trouble light
Coolant temperature
Rear fog indicator Engine trouble
indicator (red
light warning lamp
indicator)
11
Summary
Battery charge
Fasten the safety belt Windscreen cleaning
indicator lamp
Vehicle maintenance
Low beam lamp Power + pole
indicator
12
Summary
13
Driving
Chapter 2 Driving
14
Driving
15
Driving
6. At the same time when the ignition all fail, then step down the accelerator cancer, the defect of the newborn.
key is turned on, make sure that the properly and then rotate the key to the If you smell the fume
dashboard alarm lamp lights shortly. If “Ⅲ” position. After the engine start, peculiar smell within the
not, then it needs to deliver your release the key and release the vehicle, please deliver your
vehicle to the Chery authorized service accelerator pedal slowly as the engine vehicle to the Chery
station for overhauling. speed increases. authorized service station for
If the driver safety belt is fastened before 4. After the engine start, run at idle speed overhauling immediately. Do not
turning on the ignition key, then the safety for several seconds, step down the continue to drive. The exhaust fume is
belt alarm lamp won’t light. poisonous that may endanger the life.
clutch, shift to the drive gear, release
the handbrake and then be ready to The exhaust system and the vehicle
Engine Start drive. ventilation system should be checked
1. Rotate the ignition switch to the “Ⅲ” 5. The normal environment temperature under the following conditions:
position but not step down the condition of the engine start is • When the vehicle is lifted for
accelerator, release the key after the -25℃-+40℃ (it m ay have other overhauling.
engine start and the key will return to abnormal conditions when the
the“Ⅱ” position. • When the sound of exhaust system is
environment temperate is out of such
changed.
2. If the temperature is normal or higher, scope).
then the engine can not be started • When the vehicle is damaged due to
Caution of Vehicle Exhaust the collision.
within 5s during the start, and then
rotate the key to the “B” position and Fume
wait for 10s before retrying.
Ventilation Notice
Although the vehicle exhaust fume is little
poisonous, it contains the carbon When the vehicle is parked in the open
3. If the temperature is lower, the engine
monoxide, of which the danger must be field for long period idle, the window
can not be started within 15s during
cautioned. The certain contents in the should be opened for at least 2.5cm. Or
start, and then rotate the key to t he “B”
engine exhaust gas and the certain open the A/C system ventilation function
position and wait for 10s before
chemicals cont ained or emitted by certain to let the fresh air into the vehicle.
retrying. If the two consecutive starts
vehicle components may result in the
16
Driving
17
Driving
Brake Brake Liquid level alarm transmitted to the steering wheel during
braking, please deliver your vehicle to
If the brake fluid level warning lamp is on, Chery authorized service station for
which shows the brake fluid level has been overhauling immediately.
lower than the lowest level, and it needs to The new brake lining can achieve best
be refilled immediately. brake effects only after run in. The brake
The brake liquid level should be checked effects may be slightly lowered within the
periodically in accordance with the initial 200km. Under such condition, the
requirements. brake effects can be compensated by
Please refill with brake enhancing the proper force on the pedal.
liquid immediately to This essential point also app lies to the new
brake lining after replacement.
Dual-Circuit Brake System maintain the liquid level
The worn-out status of the brake lining
between M AX and M IN marking and
Your vehicle is equipped with “X” deliver your vehicle to the Chery depends on the working condition and
dual-circuit brake system. The other authorized service station for the driving method to large extent. For the
circuit will still keep effective op eration checking of the brake system. vehicles mainly for city transportation, the
even if one circuit has fault. working condition of the brake lining is
Ope ration Instruction of relatively poor due to the frequent start
In case of the failure of one
Brake System and stop. Therefore, make sure to deliver
brake circuit, it will needs
It’s quite normal if the brake system issues your vehicle to the Chery authorized
more force to step down the
noise occasionally. The long period service station for the checking of brake
brake pedal and the stop distance will
grinding or screaming noise between the lining thickness or the replacement of
be lengthened. In case of the
metal and the metal may indi cate that the brake lining in accordance with the
occurrence of such condition, please
brake disc was severely worn out and maintenance mileage specified in the
deliver your vehicle to the Chery
should be replaced. At that time, please M aintenance.
authorized service station for
deliver your vehicle to the Chery For downward slope driving, it should
overhauling before you continue your
authorized service station for overhauling. shift to low gear at proper time so as to
journey.
If there is consecutive shake or shock sufficiently take advantage of the brake
18
Driving
effects of the engine and reduce the load Brake Booster: under emergent braking so as to escape the
of brake system. At that moment, the obstacles.
brake pedal should be stepped down all If the brake booster can’t function because The ABS on this vehicle integrates EBD
the time even the braking is required. the vehicle is trailed or it’s due to its own system (Electric Brake force Distribution),
The moisture brake disc will reduce the fault, then it needs to enhance the stepping making the ABS performance better.
brake efficiency. After paddling, heavy force to compensate the boosting effects of
rain or car wash, it should step down the the booster. Reaction of ABS
brake pedal slightly to generate friction
heat between the brake disc and the brake All pedals should be
lining so as to evaporate the water and stepped down to the end
resume brake effects. and should fully return
with free movement.
19
Driving
20
Driving
Handbrake When releasing the handbrake, pull up the synchronizer to start the engine under
handbrake lever slightly, push down the neutral gear and engine stall status is
release button at the end of the handle and strictly prohibited; otherwise the
push downward. service life of the synchronizer will be
affected.
The handbrake is applied on the rear
wheels. It can step down the brake pedal at • The flap method (namely the operation
method of one pulling and one
the same time the handbrake is pulled up
releasing) is strictly prohibited during
so that it can pull up the handbrake much
gearshift. Please always hold the
easier.
transmission lever with hand so as to
Pull up the handbrake handle after parking Shift greatly reduce the slide and friction
so as to avoid the humping due to time and the worn-out of the
temporary carelessness. The hand brake Use/Operation M ethod and Notices: synchronizer lock ring.
handle is located at the middle of the front • During gearshift, fully step down the • Do not leave your hand on the gear
row of seats. clutch pedal and release the driver selector lever during driving;
from the engine torque and then otherwise it will result in the early
operate the gearshift lever for gearshift worn-out of the gearshift fork.
rapidly. • In case of the detection of any
M ake sure to pull up the abnormal evidences such as abnormal
handbrake handle before leaving the • The low speed gear should be used for
downward slopes and turns. The slide noise of the transmission or the
vehicle. obvious heavier operation during use,
with disengaged clutch is not allowed.
please stop the vehicle for inspection
The brake lamp will light when applied • When shifting the transmission from
low gear to high gear, do not conduct immediately and continue the driving
with handbrake under the condition that
gear skip operation; otherwise the once the trouble is resolved.
the ignition switch is turned on.
service life of the synchronizer will be
Pull up the handbrake lever when using
handbrake.
affected. Steering
• The forced gearshift by means of
21
Driving
In order to avoid the damage of power are loosened or worn out. After paddling, make sure to drive slowly
steering system: and step down the brake pedal slightly for
• Whether the steering components are
several times to remove the water from the
• The time when rotating the steering loosened or worn out.
brake. The water on the brake will lower
wheel to the end (to left dead point
• Whether the wheel alignment is the brake performance.
and right dead point) should not
correct.
exceed 10s during engine running.
Three-Way Catalytic
• When the power steering liquid in the Paddling
power steering liquid reservoir is Converter
lower than “M IN” mark, please refill
with power steering liquid If it’s must to paddle during journey, make The catalytic converter will help reduce
immediately. Do not drive the vehicle sure to drive slowly and carefully, the pollution of exhaust gas.
before refill. especially when having no knowledge of
the water conditions. Do not drive forward
In case of trouble of power steering M ake sure to use unleaded
further if the water can submerge the
system or the engine stall, the vehicle will fuel. The leaded fuel will
wheel hub.
result in the permanent
lose the steering boosting. You still can
rotate the steering wheel with great During paddling, the traction force and the damage of the catalytic converter and
strength. brake performance of the vehicle will be the oxygen sensor. Chery Automobile
lowered and the vehicle will have the Co., Ltd. will not be liable for any
In case of vehicle deflection or tremble danger of stall. damages arising from the use of leaded
during the driving, please check the fuel. Such damages are excluded from
following items: In case of the water ingress into the intake
the warranty scope. If you refill with
pipe of the engine, it will cause the serious
leaded fuel accidentally, please cont act
• Whether the tire pressure is damage of the engine. The deeper
insufficient. paddling will result in the water ingress with the nearest Chery authorized
into the transmission through the service station.
• Whether the tire is worn evenly.
transmission air vent, which will result in
• Whether the suspension components the damage of the transmission.
22
Driving
23
Driving
M ake sure to turn off the ignition switch Stroke Distance/Engine Temperature
before leaving the vehicle. Do not run the
Fuel Consumption
The frequent cold vehicle start and the
engine when no one is in the vehicle. The
short distance journeys will result in the
negligence of this point may result in the The fuel consumption is obvious increasing of the fuel
movement of the vehicle, which will result influenced by the following consumption.
in the body injury or property damage.
factors: Traffic and Road Condition
Chassis Protection The crowded traffic, upward slopes, multi
Selection of Vehicle Speed or Gear
curved routines and rough roads will cause
Your vehicle is equipped with heat detrimental influence on the fuel
insulation plate. Do not apply the paint on consumption.
the body of heat insulation plate, exhaust
pipe or catalytic converter or the Good Driving Habits
surrounding areas. Do not disassemble the The prediction of danger and keeping safe
heat insulation p late. driving distance with foregoing vehicle
will not only reduce the fuel consumption
but also reduce the wearing and noise of
the brake.
24
Driving
Vehicle Load Status heating immediately whenever After stopping the vehicle
unnecessary. and the engine, the radiator
The increasing of vehicle load will result fan will continue running for
• Check/adjust the tire pressure
in the higher fuel consumption. certain period since the engine is still
periodically.
under hot condition and will stop
Vehicle Techni cal Status • Conduct vehicle maintenance running when the engine is cooled to
periodically, preferably conducted by certain temperature. Even though, the
The low tire pressure or improper engine
Chery authorized service station. fan may still start suddenly in case of
and vehicle maintenance also will result in
the sudden temperature increasing of
higher fuel consumption.
the engine compartment due to the
Radiator Fan influence of the ambient environmental
Essentials for Fuel- Saving
temperature (sunshine exposure or
Driving and Environmental The radiator fan is an electrical fan with high temperature region). Therefore,
Protection: the working condition controlled by the cautions should be taken when
engine ECU. This switch will operating in the engine compartment
automatically turn on the fan circuit when
• Fuel-saving driving and use excess so as to avoid the accident.
the coolant or the engine compartment
electrical loads only if needed.
reached to certain temperature.
• Start without the heating of the Instruction
vehicle.
If the fan isn’t running when the coolant
• Use the accelerator smoot hly. temperature reached the fan start
• Shift to the next higher gear as soon as temperature, then check if the fan fuse is
possible so as to achieve lower engine burnt out. Replace the fuse if necessary.
speed. The fan speed is independent from the
• Prediction of traffic condition. engine speed and the gearshift to low gear
will not promote the cooling effects of the
• Turn off A/C and rear windscreen fan. Therefore, it’s unnecessary to shift to
25
Driving
26
Operation & Adjustment of Inside Devices
27
Operation & Adjustment of Inside Devices
after the key is pulled out till a click of The ignition switch is equipped with
I. Introduction of blocking is heard. anti-repeatable start device inside. Once
Vehicle Functions “I”–unlock the steering system. The circuit
the engine runs, the device may prevent
mis-start of engine, so that it avoids
of electric accessories is connected and
damage from the engine and flywheel.
Steering wheel lock/ignition small electric appliance such as inside
switch lights can be operated. But the ignition If the engine does not start, the key must be
switch and main electric loop are turned to “B” before restart, and then
disconnected. turned to the position. After start, release
If the key could not or is difficult turn to the key and it will return to “II” position.
the position from “B”, slightly turning the
steering wheel and then the locking system
of steering wheel may loosen. Once the engine started, the
key must be released. DO NOT
The ignition switch key shall not be placed remain at “III” position for a long
at the position too long to avoid the power time.
of battery running out of.
“II”–Connect the ignition circuit. All
electric loops can work. Alarm lamps and
indicator lamps light. It is the normal
Combined steering wheel lock/ignition position of key during driving and the
switch has the following key positions: position that must be selected for towing
“B”–Ignition switch turns off and the the vehicle.
steering wheel is blocked. “III”–Connect the motor and start the
When the key is pulled out from the engine. When the lock hole is at the
ignition switch, the steering wheel lock position, headlamps and electrical
acts and t he steering wheel is blocked. equipment that consume more power will
be disconnected fully.
To lock the steering wheel, it shall turn it
28
Operation & Adjustment of Inside Devices
Horn
29
Operation & Adjustment of Inside Devices
Inte rmittent Wiping High Speed Wiping Pull the switch handle toward to the
steering wheel and hold in the position, the
cleaning fluid will spray out front the
injection nozzle in front of the windscreen
and the wiper begins action synchronously.
Water spray will stop after releasing the
handle, but the wiper still acts several
times.
31
Operation & Adjustment of Inside Devices
Sun Visor Control Switches on Front Electrical Window ( )
Left Door
Front left door
32
Operation & Adjustment of Inside Devices
Even if the ignition switch turns off, the push it to the original position.
electrical windows may work.
Carefully close the window Press the cigarette lighter with hand and it
The control switches on the front left door and observe to avoid injury from will automatically pop in the original
may regulate the left and right windows. squeezing. position after heating, then you can pull it
When the front right window safety switch out for use.
on the front left door is pressed, the
regulation of front right window may be Front Ashtray, Cigarette
controlled by the control switch on the Lighte r The cigarette lighter shall not
front right door. remain in inserted state for a long time
Press down of draw up the switch to open to avoid danger. It shall be taken away
or close the window. Release the switch if a child stays in the vehicle alone.
during window glass up or down, the glass
shall remain in the current position.
Lighting control
Every window regulator switch has point-
touch function, the glass may drop to the Please follow related traffic rules while
bottom automatically when the regulator using the illumination equipment as below:
switch is pressed for 300 milliseconds and
released.
Besides the control switch of driver side
window, the door trim panel in the driver
side is supplied with the regulator switch
for front right window.
The front ashtray and cigarette lighter are
located near to the gear lever.
To open the front ashtray, you need to pull
its arc backward; to close it, you need to
33
Operation & Adjustment of Inside Devices
Headlamp s witch Turn the headlamp switch on the Flicker of Headlamp
instrument panel to position, the
dipped headlight position, the dipped
headlight will be on.
34
Operation & Adjustment of Inside Devices
Switches of front and rear fog lamps are is only allowed to use in very low Inte rior Front and Middle
located at the control handle under the visibility.
steering wheel to the left. Ceiling Lamps
When the headlamp switch is at Turning Indicator
or position, turn the handle
(the part with black dot as shown in the
figure) will connect the front fog lamp first
and then the rear fog lamp.
To turn on the fog lamp, the headlamp
switch must be turned on first (at
35
Operation & Adjustment of Inside Devices
The triangle shown in the figure is the be off when the ignition switch is turned
danger alarm lamp switch, which is in the off or changed to other position.
central instrument panel between two air
outlets.
The switch is only used in emergency case
for warning the following vehicles that the
car has faults or danger. Press the switch to
connect/ disconnect the system. The danger
alarm lamp is available even if the ignition
switch turns off.
After the alarm lamp is connected, the
indicator lamp on the switch (yellow part)
will flash. Left and right turning indicators
on the combination instrument will flicker
at the same time.
Braking Lamp
When step on the brake panel, the braking
lamp will be on. It will be off with the
brake pedal released.
Reversing Lamp
When turn on the ignition switch and the
vehicle is at reverse position, the reversing
lamp will be on. The reversing lamp will
36
Operation & Adjustment of Inside Devices
Sound System
CD Panel ( )
① POWER supply ④ M anual TUNE ⑦ Preset key 2 ⑩ Preset key 5 ⒀ BAND key
② OUT key ⑤ M ute & Clock key ⑧ Preset key 3 ⑾ Preset key 6 ⒁ Auto-scan memory key
③ Volume control ⑥ Preset key 1 ⑨ Preset key 4 ⑿ MODE key ⒂ Auto-scan key
Note: Please read the sound system instruction manual supplied with the vehicle if it is not equipped with the system as below.
37
Operation & Adjustment of Inside Devices
Function Instruction “M UTE”; ⑧ Preset key 3:
− Under CD mode, it is pause switch,
− Under radio mode, it is presetter No.3;
press lower right key, convert the
① Power key: Press the key to switch
display between radio and clock; − Under CD mode, it is scan play key.
on/ off the power supply.
− Under clock state, long time press the Press the key and LCD shows
② OUT key: Press the key for CD out. key and the hour display flickers, then “SCAN” skip to next song, play for
10s and then skip to next song again.
③ Volume control: Press the key to press the key again, the minut e display
Press the key to stop scan when you
select BASS, TREBLE, BAL, flickers, turn key ① to adjust clock.
are hearing wanted song, and return to
FADER and VOL in order. ⑥ Preset key 1: normal play condition.
Clockwise turn the potentiometer
for increasing the right output of − Under radio mode, it is presetter No. ⑨ Preset key 4:
VOL, BASS, TREBLE and BAL, 1;
− Under radio mode, it is presetter No.4;
and front output of FADER, − Under CD mode, for CD play. Slightly
counterclockwise turning is − Under CD mode, it is the selection key
press the key, and LCD shown
opposite. “SHUF” and it may play the songs in for EAS (electronic anti-shock). Press
the CD, press the key again, it shuts the key for 2s to cancel the ESP
④ M anual TUNE: Under the radio function and LCD won’t show “EAS”.
mode, press the key for upward/ down the play function and returns to
normal play order. Press the key for 2s again to resume
downward tune, long time press the the EAS function and LCD shows
key for single step tune. Under CD ⑦ Preset key 2: “EAS”.
mode, press “∧” or “∨” to select
songs forward or backward, “∧” − Under radio mode, it is presetter No.2; ⑩ Preset key 5:
for next song (e.g. 1-2) and “∨” for − Under CD mode, repeatedly play the − Under radio mode, it is presetter No.5;
last song (e.g. 2-1). Press “∨”or CD. Press the key for short time, it
“∧” for fast onward or backward. will play the current song repeatedly.
⑤ M ute and clock key: LCD shows “RPT”. Press the key
again, it may cancel the repeating
− Under radio mode, press lower left key function.
for mute switch and LCD shows
38
Operation & Adjustment of Inside Devices
− Under CD mode, it is programming radio/CD. then automatically search other
memory of CD. Press the key for 2s channels.
when playing CD, save a ⒀ BAND key: Wave band conversion
switch. − When a frequency is flickering, long
programming song and the display
time press the preset key to save the
shows [P.XX] (the range for XX is ⒁ Auto-scan memory key: channel in corresponding presetter.
1-10) that flickers for 5s, press the key
− Press the key 2s, the machine will scan
again during flickering to confirm the
the whole band from high frequency to Basic operation of radio
programming song has been saved.
lower and save the channels with
Repeat the above process to save next
stronger frequency in 1-6 presetters,
song, return to normal play state after Preparation
confirmation. When the CD songs of and finally stop at the channel saved in
presetter No. 6;
which are saved is out, the content for − Slightly press the key POWER ①,
programming memory will − Under CD mode, it is the turn on the power supply and LCD
automatically eliminate. programming elimination of CD. Press shows digits.
the key 2s to clear programmed songs
⑾ Preset key 6: − Slightly press AM /FM switch to select
and LCD shows [CLR], which flicker
− Under radio mode, it is presetter No.6; for 5s. Press the key again in the suitable wave length. LCD shows AM
flickering period to confirm that the or FM .
− Under CD mode, it is CD
programming play. Press the key when programmed son gs have been cleared,
and then return to normal play state. If Auto-tune
playing CD, the machine will play
no any operation is taken in the period,
from the saved song P1 if there are − Slightly press the key “∧”TUNE ④,
saved songs. Press the key ④ “∨”, it returns to programming play state.
the radio searches channels from high
“∧”, convert to next saved song. ⒂ Auto-scan key: frequency to low;
Press the key again to cancel the
− Slightly press the key and the radio
programming play function and return
searches channels from high frequency
to normal play order.
to lower automatically. When a
⑿ MODE key: signal selection switch, channel is searched, LCD flickers the
which may convert between frequency of the channel for 5s, and
39
Operation & Adjustment of Inside Devices
− Press the key “∨”TUNE④, the radio silence and recovers broadcasting. In
searches channels from high frequency addition, LCD shows corresponding preset
to low and automatically block the key No., which means the channel has
channel it searched, and show the been saved in the preset key.
frequency of channel on the LCD.
Play channel
− If the channel is not the one you
wanted, press the key again to search
First, select wave band (AM /FM )
for next channel.
according to demand, and then slightly
− Press the key TUNE ④ for 2s for press the p reset key that saves channel, the
manually searching channel. Press and saved channel will play. LCD shows the
hold the key, the radio will corresponding preset key No. and saved
continuously scan channels, release channel frequency. Repeat the above
the key at once when wanted operation to save or play other channels
frequency is heard. If no any operation respectively.
is taken in 3s, it will turn to auto-scan
state. Disc maintenance
− If the channel is caught, press the
above two keys to adjust the frequency Please take out the disc while it is not used
exactly. and place it in the CD box to avoid dust
and damage. DO NOT leave your
fingerprint on the disc as taking out. The
Save or Play Channel disc shall prevent heating and directly
sunshine.
Save channel
After the channel is obtained manually or
automatically, p ress the preset keys (⑥-⑾)
at least 2s till the radio app ears a short
40
Operation & Adjustment of Inside Devices
A/C System
Ventilation
Outside air enters in the vehicle through
the air inlet in the lower part of the
windscreen. Please keep the air inlet clean
without snow and leaves for ensuring
normal heating, ventilation and efficient
work.
41
Operation & Adjustment of Inside Devices
42
Operation & Adjustment of Inside Devices
Central vent hole Side air outlet Defrost air outlet of front
windscreen
The adjusted air flows in the vehicle The adjusted air flows in the vehicle
through two central vent holes. The air through two side air outlets. Through the air outlet, cold air or warm air
flow direction may be changed by turning are guided to the side windows (controlled
the grille. within exterior rearview mirror).
1. Side defrost air outlet 2. Side air outlet 3. Defrost air outlet of front windscreen 4. Central vent hole
43
Operation & Adjustment of Inside Devices
Ceiling Air Outlet and
Control
Passengers who sit in middle and rear
seats may control the airflow direction of
A/C by adjusting the ceiling air outlet and
blower switch.
(Note: the operation is only available in
the case of front blower running.)
44
Operation & Adjustment of Inside Devices
Control Panel Ventilation & Warm Air The airflow speed is subject to the blower,
which may be started during driving if
necessary.
1. Cold/warn adjusting switch A/C system adjusts the temperature by
2. Airflow distribution switch mixing cold and warm air. The
3. Blower switch temperature may be constant under any
4. Defrost switch of rear windscreen speed.
5. Internal/external circulation control
lever
6. A/C switch
45
Operation & Adjustment of Inside Devices
Temperature cont rol switch cooling or heating the air inside vehicle.
The switch is used for controlling the
temperature of air flowing out the vent.
Blue position: Cold air
Red position: Warm air
The lever is used for selecting fresh air The switch is used for selecting the
outside or air circulation inside the airflow direction.
vehicle. There are 5 steps for the switch as below:
Blower Switch External circulation mod e ( )
Outside air enters in the vehicle.
The switch is used for controlling the Used for normal ventilation, warm air or
speed of blower (4 steps totally). The cooling.
airflow speed is adjusted by the blower. Internal circulation mode ( )
Starting the blower during driving in order Air inside vehicle circulates within the
to increase comfort. vehicle. The mode is used in cases of
dusty environment, or preventing outside
exhaust gas entering in the vehicle, rapidly
46
Operation & Adjustment of Inside Devices
Head position
Head and foot position
Foot position “Head and foot” position ( ) “Foot, defrost” position ( )
Foot position, defrost
The air flows out from central vent hole The air flows out from the air outlets in
Defrost
and air outlet in the bottom of front seat. the bottom of front seat, defrost air outlet
of windscreen and defrost air outlet of
front window.
47
Operation & Adjustment of Inside Devices
“Defrost” position ( ) A/C switch Max. Cooling
The air flows out from defrost air outlet of It shall open the windows shortly to
windscreen and defrost air outlet of front The switch is used for starting and discharge the inside hot air rapidly when
window. stopping A/C compressor. the vehicle exposes in sunshine for a long
time in hot weather.
Start the engine and turn the blower switch A/C switch: ON
to proper airflow speed, switch on the A/C Internal/ external circulation control lever:
switch for starting the air conditioner. The ( )
indicator lamp is on with A/C running.
Press the A/C switch button to stop the Airflow distribution switch: ( )
A/C. when the blower switch is at “OFF” Temperature control switch: Turn to the
position, the A/C compressor does not bottom counterclockwise
work. (Blue)
Blower switch: M ax. rotation speed
A/C System
Ventilation, heating and cooling
components consist of a control system,
which may provide the highest comfort
under any weather condition.
Normal cooling
The cooling unit of A/C system cools the
It is for the normal cooling during long-
air down and removes moisture and dust
The A/C system may lead to distance journey and high speed driving.
such as pollen, etc.
the engine overheated with it working A/C switch: ON
while the vehicle is climbing a lon g Internal/ external circulation control lever:
slope or at traffic jam. Observe the ( )
water temperature gauge and shut
down the A/C if the engine is
overheated.
48
Operation & Adjustment of Inside Devices
Ventilation
Outside air flows in the vehicle through DO NOT use force heating
central vent holes and side air outlets. for a long time to prevent inside
A/C switch: OFF air grimy and window misty. The
Internal/external circulation control lever: internal circulation switch shall be
turned off if the windows are
( ) misty or wet. Force heating is
Head and Foot Position
It is used for transition phase such as the Airflow distribution switch: ( ) or only used for rapid heating up,
temperature is low outside, without and it shall return to normal
( )
sunshine. When adjusting the temperature Temperature control switch: Blue heating as soon as possible.
control switch between cold (blue) and Blower s witch: Any position
warm (red), the warm airflow enters in the
bottom of the vehicle, cold air and normal
temperature air flow in upper space.
A/C switch: NO or OFF
Internal/ external circulation control level:
( )
Airflow distribution switch: ( ) Force heating
Temperature cont rol switch: between blue A/C switch: OFF
(cold) and red (warm) Internal/external circulation control lever:
Blower s witch: Any position
( )
49
Operation & Adjustment of Inside Devices
II. Instruction of
Designation
Instrument Panel ( )
51
Operation & Adjustment of Inside Devices
Combination Instrument Panel( )
1. ABS defect alarm lamp 7. Indicator lamp of rear fog 13. Engine defect alarm lamp 18. Left turn indicator lamp
2. Parking brake indicator lamp lamp 14. Coolant temperature/ level 19. Door not close alarm lamp
3. M ode & adjusting button 8. M aintenance alarm lamp alarm lamp 20. Air bag alarm lamp
4. LCD 9. Low fuel level alarm lamp 15. Position indicator lamp 21. Safety belt alarm lamp
5. High be am ind icator lamp 10. Braking disc alarm lamp 16. Right turn indicator lamp 22. Braking system defect
6. Indicator lamp of front fog 11. Low engine oil pressure 17. EPC defect alarm lamp alarm lamp
lamp alarm lamp
12. Battery charge ind icator
lamp
52
Operation & Adjustment of Inside Devices
Warning Device Low Fuel Level Alarm Lamp lights as well. You shall go to the Chery’s
special service station for check and repair
as soon as possible. Carefully driving is
Warning device is used for indicating the
required to avoid high speed driving.
running state of vehicle and the vehicle
Important notes related to the use of ABS
whether has problems that may lead to
system, please refer to the chapter of
serious damage or injury to the driver. If
When the fuel in the fuel tank is less than “Braking”.
any system of the vehicle appears
functional defect, the corresponding alarm 10L, the lamp lights for warning and the
lamp shall be on or flash. fuel gauge hand will point to red warning Parking brake alarm lamp
line.
M ost alarm lamps shall light shortly for
systemic self-inspection when the ignition Please refill fuel as soon as possible when
switch turns on. If an alarm lamp does not the alarm lamp is on.
light, or an alarm lamp still lights or ABS defect alarm lamp
flashes after the engine started, please get
to Chery’s special service station to have The lamp only functions with the ignition
related system checked and repaired switch on.
immediately. The lamp keeps lighting as the hand brake
working.
The lamp will light shortly when the
ignition switch turns on and the ABS
system will carry on self-inspection to
ensure the system whether can work
normally. If the lamp is constantly on or
flashes after the ignition switch turned on
or during driving, it means ABS system
having defects, but the vehicle still has
general braking function (without ABS) ,
unless the braking system alarm lamp
53
Operation & Adjustment of Inside Devices
Braking system alarm lamp Parking/position indicator
lamp
If the braking system alarm
lamp lights during driving, it means
double braking loops failed. In the
case, you should drive carefully and
The lamp only functions with the ignition get to Chery’s special service station The indicator lamp lights when the
switch on. It will light when the braking immediately to have it checked and position lamp is on.
fluid level is low. repaired by professional technicians.
In consideration of braking
Check the braking fluid level whether too
performance decreasing seriously and Safety belt alarm lamp
low when the lamp is on. The braking
fluid shall be refilled immediately between braking distance increasing, you shall
keep longer distance with the front
M IN mark and M AX mark if the level is
vehicle during driving and increase
too low. Please get to the Chery’s special
pedal pressure properly as braking.
service station to have the system checked.
If the ABS alarm lamp and braking
system alarm lamp light
synchronously and constantly, the With the ignition switch on, the alarm
vehicle shall be stopped immediately lamp will light to remind the driver to
under the in case of ensuring safety. fasten the safety belt if he/ she did not to
Please get to the Chery’s special do so.
service station to have the braking
system checked before your journey.
54
Operation & Adjustment of Inside Devices
Engine defect alarm lamp High beam indicator lamp Air bag alarm lamp ( )
55
Operation & Adjustment of Inside Devices
Low engine oil pressure alarm Coolant temperature/level
lamp Please get to Chery’s special alarm lamp
service station to have it checked if
the engine oil consumes too fast.
56
Operation & Adjustment of Inside Devices
Door not close alarm lamp If the lamp lights during running, it means turn off the lamp.
the EPC failed. Please get to Chery’s
special service station to have the system Engine coolant te mperature
maintained as soon as possible.
gauge
Braking disc alarm lamp ( )
57
Operation & Adjustment of Inside Devices
Please get to Chery’s special service Fuel gauge
station to have it maintained if the hand
remains in the zone for a long time. DO NOT open the water tank
cover when the engine is still hot to
Between “C” and “H”–normal temperature avoid scalding. The engine will not
zone start until the trouble is removed.
The hand shall keep in the zone under
normal driving state. NOTES:
The hand may departure from the range Installation of auxiliary headlamp in front
when the environmental temperature is of the cold air inlet in the lower part of
very high or the engine loads heavily. As front bumper will affect the flow of Fuel tank capacity: 45L.
long as the coolant alarm lamp does not cooling air and is not good for engine When the hand points to “E” (empty, the
light, the vehicle can run normally. The cooling. position of arrowhead) there is about 3L of
engine must be shut down and check the fuel remaining in the tank.
The engine is easy to be overheated if the
cooling system if the coolant alarm lamp
environmental temperature is very high The hand will move from “F” (full) after
lights for warning.
and the engines works with heavy load! refilling the fuel tank and driving some
Higher than “H”– overheated zone distance.
Front spoiler functions on guiding cooled
If the hand points the red zone, it means air. The engine may be over hot if the The available filling amount is lower than
the engine ov erheated. Please stop the spoiler is damaged or broken due to marked capacity when refilling due to
vehicle safely and turn off the ignition collision. Please get to Chery’s special remaining oil.
switch. Look for reasons after the engine service station to have front bumper
cooling down. repaired in time. If the low fuel level alarm lamp lights,
please refill fuel as soon as possible. Refer
to “low fuel level alarm lamp”.
58
Operation & Adjustment of Inside Devices
Speedometer LCD After the hour position is adjusted, wait
for about 6s and the minute position will
flash, and then adjust it by clicking the
adjusting button. Every clicking increases
one minute, and long time pressing for
automatic increase.
After the clock is adjusted for several
The conversion method for subtotal seconds, it will not flash, which means the
mileage/ momentary oil consumption/ time is adjusted well.
average oil consumption/ clock is as
below:
It indicates the current running speed of
the vehicle. Click (<0.3s) the clock adjusting button on
the dashboard to convert the display
between subt otal mileage/ momentary oil
NOTES: consumption/ average oil consumption/
clock. Long time press (>1s) the button
The speedometer is subject to the under subt otal mileage state to clear the
dimension of tires the vehicle used. Please subt otal mileage.
use Chery’s genuine tire with former
dimension. Otherwise the speedometer The adjusting method of clock is as below:
will not show the proper speed. Click (<0.3s) the clock adjusting button on
the dashboard, the right part of LCD may
be adjusted to clock display state. Then
long time press the button about 4s, the
hour position of clock will flash, it may be
adjusted by clicking the button. Every
clicking increases one hou r. Lon g time
pressing makes it automatically increase.
59
Operation & Adjustment of Inside Devices
60
Safety
Chapter 4 Safety
61
Safety
62
Safety
All doors can be locked externally by The door may be locked or unlocked
pressing the safety handle and closing the internally via the safety handle on the
door with the exception of front left door. sliding door shield (pull the safety handle
forward to unlock, pull it backward to
Sliding Door lock), then draw back the internal handle
of the door to open the door.
63
Safety
Central Control Lock ( ) Insert the key in the lock hole and turn
clockwise to open the back door. Turn the
The temperature inside the key counterclockwise to lock the back
The central door lock is controlled by the vehicle rises very fast after the door. Put down the back door with slight
driver side door (front left door). When the engine flameout in hot weather. force to make it closed firmly when
driver side door (front left door) is locked
Even if in very short time, people locking it.
or unlocked by the key or safety handle,
or animals may hurt or even die
all doors can be locked or unlocked at the (including brain death) under such
same time with the exception of back door. high temperature, it is dangerous
(Note: the back door can be locked or Exhaust gas is harmful. Please
especially for babies. Therefore,
unlocked by key only) stop the engine after the back door is
DO NOT leave babies or animal in
the vehicle when you lock the opened to avoid the exhaust gas
doors. entering in the driver’s cabin.
Back Door
Release Rod of Filler Cap
64
Safety
Draw back the release rod at the lower left lock first when closing the engine
part of dashboard to open the filler cap of
Open Engine Bonnet bonnet, and then let it freely drop in
fuel tank. The fuel filler cap is located in the lock claw for close.
the lower part between front left door and
left sliding door.
66
Safety
67
Safety
Seat & Safety Protection • Properly adjust the headrest to level its Adjustme nt of Front Seats
top end to the head top.
68
Safety
69
Safety
Release the button after adjusted properly. • M ove the middle seats forward
properly to ensure enough space for
Removing and assembling method folding the rear seats.
of headrest:
• Open the luggage boot cover and pull
Push down and hold the spring clip at the the folding drawstring of rear seats
external side of the headrest guiding with hand to fold the seatback.
element and pull out the headrest from the
guiding element as removing the headrest.
In the assembly of headrest, distinguish • Press the folding button of middle seat,
the front/ rear seat headrests first (the front it will automatically pop up. It will
one is bigger and the rear one is smaller) have enou gh space for passengers
and then push the headrest pin into the entering in rear seats.
guiding element, till the spring clip on the
guiding element engages with the pin • Reposition method of middle seats is
correctly. reverse, turn the seats over first and
make the seats fixing on the bottom
plate, and then draw back the seatback • Press the seat folding button and turn
Folding of Middle Seats handle to make it popping up. over the rear seats leaning to the back
of middle seats firmly.
Please follow the method as below to fold
the middle seats and sit on the rear seats if Folding of Rear Seats
you need to sit on the rear seats.
Reposition of rear seats
If you have more luggage that need to be
• Pull the folding handle of middle placed in the luggage boot, please follow It only needs to level the seats and erect
seatback to fold the seatback and the steps as below: the seatback when the rear seats are
cushion together. repositioned.
70
Safety
71
Safety
Fastening Seat Safety Belt M ake sure that each safety belt using Maintenance of Seat Safety
correct buckle.
Belt
Smoothly pull out the safety belt. The belt
may be blocked if excessive force is Middle 2-Point Safety Belt for
applied or the vehicle is on a slope. The
Check seat safety belt
Middle Seats
seat safety belt shall be placed on the
middle of the external shoulder. The waist
belt portion shall cling to the hip instead of
stomach.
Air Bag ( )
Fasten the safety belt and
The combination of air bag and safety belt keep proper distance with the
can help reduce the danger of severe steering wheel at any time. Only
injury in case of severe collision accident. the use of safety belt can
guarantee that the body is at such
Notes: position where the air bag can
exert the best effect.
The inflation of air bag will emit loud
noise. In addition, it will remain residue of
harmless powder similar as smok e as well. Front Air Bag
All of these are normal phenomenon.
The seat and seatback must be correctly
Extremely dangerous! DO
positioned to coordinate in such manner
NOT use the reverse direction child
that the safety belt can achieve best
seat on the seat equipped with front
protection effects. Adopt vertical sitting
air bag! posture with the back end clinging to the
seatback as close as possible and the
rearward inclination angle of the seatback
no more than 25o. DO NOT make the front
seat close with the dashboard too much.
Grasp the steering wheel with slightly
The Front passengers can obtain effective bended arm during driving, which is the
protection only with the sitting posture as ideal driving status that can reduce injury
shown in the right figure above. from driver when the air bag is swelling.
73
Safety
Air Bag Alarm Lamp life of your vehicle air bag, Chery’s
special service station is willing to query
the related data for you.
74
Safety
Extremely dangerous! DO
NOT use the reverse direction
child seat on the seat equipped
with front air bag!
75
Safety
76
Emergency Procedures
77
Emergency Procedures
78
Emergency Procedures
Replace Bulbs Stop/ position lamp bulb: passing through the location slot,
12V 21W/ 5W detach the fastener to both sides and
Front fog lamp bulb: take out the bulb, notice the alignment
Unless the event is very urgent, the owner 12V 55W mark of bulb. Pull off the wiring
is not allowed to replace bulbs of harness connector on the bulb. The
headlamp unit individually. If the bulb of position lamp is inside the
replacement is necessary, please turn off shield of high beam/ dipped headlight.
lamps and shut down ignition switch After the headlamp bulb is
replaced every time, calibrate the Pull out the bulb and harness
before replacing any bulb. connector together when it is replaced.
headlamp. Chery’s special service
DO NOT directly hold the bulb glass by 4. Notes: The surface of new bulb shall
station can offer you the service.
hand, otherwise the fingerprints remained not be touched by hand to prevent
on the glass will be heated and volatilized effect on bulb brightness. The lighting
after the lamp lighting, and then deposit on Headlamp Unit (Including system is a safety component, please
the surface of mirror to blacken the make sure every detail of replacement
High Beam / Low Beam / proper. Get to Chery’s special service
reflector.
Position / Turn Indicator station to have it repaired if necessary.
The same model of bulb must be used
when it is replaced. Please check the bulb
Lamps)
specification before installation.
Replace the corresponding bulbs
Headlamp bulb: according to the following steps if the
12V 55W headlamp does not work due to damage.
Bulbs for turn indicator, reversing, rear 1. Open the engine bonnet.
fog lamps: 2. Unscrew the shields of bulbs
12V 21W counterclockwise at the positions
Bulbs for license plate, position, turn shown in the figure.
indicator and high-mount ed stop lamps: 3. Press the fasteners of bulb holder
12V 5W downward with hand and make them
79
Emergency Procedures
Taillight Bulb press the fasteners of bulb holder and License Plate Lamp Bulb
make them passing through the location
slot, then detach the fasteners to both sides
and take out the bulb, notice the alignment
mark of bulb.
4. Notes: DO NOT touch the surface of
new bulb with hand to avoid the effect
on bulb brightness. Lighting system is M ounting position: Above the rear license
safety components, every detail for plate.
replacement shall be prop er. Please get
to Chery’s special service station to 1. Unscrew the self-tapping bolts for
1. Replace the corresponding bulb have it repaired if necessary. fixing license plate lamp and remov e
according to the following steps if the it.
taillight does not work due to damage. The rear bumper must be removed when 2. Pull out the bulb holder and remove
replacing bulbs of rear fog lamp and failed bulb.
2. Open the back door and unscrew two reversing lamp. Please get to Chery’s 3. Install a new bulb in the bulb holder
nuts that fix the taillight from the special service station to have it repaired and fix the bulb holder.
internal side of luggage boot in time if there is bulb failur e. 4. Fix it with self-tapping bolts.
counterclockwise. Then unscrew two
mounting bolts on the taillight surface High-Mounted Brak ing Lamp Inte rior Front Ceiling Lamp
counterclockwise, pull off the harness Bulb
connector of taillight and take out the Bulb
taillight. High-mounted braking lamp bulb cannot Turn off interior lights.
be replaced individually. Please get to Insert a screwdriver in the gap between the
3. Counterclockwise unscrew the bulb Chery’s special service station to have it
shield according to the position as lamp housing and lampshade, take out the
repaired in time. lampshade carefully.
shown in the figure.
Replace the bulb and install the reflector.
Pull off the wiring harness on the bulb and
80
Emergency Procedures
81
Emergency Procedures
82
Emergency Procedures
83
Emergency Procedures
Replace Wheel
Please follow the
precautions as bellow before
lifting the vehicle.
84
Emergency Procedures
Driver Tool Jack Lift Point Jack lift point of front wheels (blackened
area in the figure)
Jack The jack can push against only the special
position in the bottom of the vehicle as
shown in the figure. The groove of jack
pushes against the convex part in the
Using a jack to lift a vehicle vehicle bottom.
is suitable for replacing wheel only.
The position shall be close to the wheel to
DO NOT operate under the vehicle
be repaired as much as possible.
at the time.
85
Emergency Procedures
86
Emergency Procedures
Battery • The battery acid is corrosive. Put on • The battery may emit highly-explosive
gloves and safety goggles. DO NOT gas when it is charges.
let the acid or lead contact your skin or
Safety Recommendations clothes. DO NOT tilt the battery, the
acid may flow out from the vent. If the
acid splashes in your eyes, use clean
The following measures water to wash your eyes for several
must be taken when the battery is minut es and take medical treatment at
delivered. once. If the acid splashes on your skin
or clothes, use alkaline water (soapy • Open flames, sparks and smoking are
water) to neutralize it and then use strictly prohibited. Please avoid sparks
clean water to rinse it. If you when wiring and electrical operation
unfortunately eat the acid, see a doctor conduct. DO NOT connect the
immediately. electrical terminals. Any short circuit
caused may create spark and give rise
to injury.
87
Emergency Procedures
88
Emergency Procedures
89
Repair & Maintenance
90
Repair & Maintenance
Regular maintenance is essential on your
vehicle during the course of use. Please
Services Offered by Items You Have to Follow
follow the maintenance schedule provided Chery’s Special Service Regularly check the level of fluids and
in the Instruction M anual strictly in order
to ensure that your vehicle is kept in best
Station refill the fluids concerned. Check whether
the tire pressure, lamps and braking
performance and better running state and
Only the genuine spare parts and materials function are normal. Check the alarm
effectively extend the service life. In
can ensure the service life of your vehicle, lamps (see the Regular M aintenance
addition, it also helps you find and remove
and here, please pay more attention: Chery Schedule below for your reference).
the potential hazard in time to avoid the
Automobile Co., Ltd. offers genuine spare Reservoirs for brake fluid, coolant and
occurrence of defect. The manual will
parts to Chery’s special service stations power steering fluid are the
describe in detail the routine maintenance,
only. So you can only get the genuine semi-transparent containers which are
examination and care method as following.
spare parts from Chery’s special service convenient to quickly, visually check these
Please read it carefully.
station only. fluids.
Chery’s special service station is the
Care & Maintenance unique professional service station
authorized by Chery Automobile Co., Ltd.
Staffs of which have been trained There is high voltage in the
The care and maintenance include two
electronic ignition system. Please DO
categor ies. One is the rout ine care and professionally by Chery Automobile Co.,
NOT touch these parts when the
maintenance which can be carried by the Ltd. They will do their best to offer the
engine is operating or the ignition
owner himself, and the other is the regular most high-quality after-sales service. If
switch turns on.
care and maintenance, examination and you dissatisfy the work of Chery’s special
repair, which shall be completed by service station, please directly email
Chery’s special service station. to: Helpdesk@mychery.com,we will
Please strictly use the oil, gasoline, brake response to your questions very quickly.
fluid and anti-frozen fluid, which are When emailing, please do not forget to
recommended in the Instruction M anual. explicitly note the model, chassis number,
Otherwise it may damage the vehicle. engine number, road mileage, and delivery
date of your vehicle.
91
Repair & Maintenance
drainage system. A/C whether works well
Everyone shall concern about the Hand brake whether works well
Turn off the ignition switch
environmental protection and contribute to Horn whether works well
before working in the engine
protect the environment.
compartment. Even if the ignition
switch turns off, the cooling fan also Notes:
op erates automatically. So please take Maintenance Schedule Air conditioner shall operate for at least 30
care of your clothes (tie) not to be minutes each month.
caught by the fan or driving belt. Daily Check:
Check the working condition of all
exterior and interior lamps and lights. Keep engine oil, grease
General Maintenance of Replace damaged or dim bulbs and lubricant and fluids away from
make sure all mirrors clean. children. Follow the safety
Vehicle instructions on the containers to
Please check the following items
while refueling: avoid your skin contacting the used
Engine oil level oil.
The vehicle washing area where the Brake fluid level
ecological dr ainage system cannot be Windscreen cleaning fluid level
damaged is available only. Tire pressure and status (cold state
only)
Check all pipelines of crankcase
ventilation system whether worn or
Used engine oil, brake fluid, folded.
anti-frozen fluid, battery and tire are Monthly Check:
disposed by qualified waste disposal Coolant level (engine cold state)
mechanism or consulting related Assembly, pipelines, hoses and oil
manufacturers about the disposal method reservoirs whether have leakage
only. DO NOT dispose them as the Brake fluid level
household waste or drain them into public Power steering fluid level
92
Repair & Maintenance
93
Repair & Maintenance
Engine Oil Dipstick and draw out again. Engine Oil Filler Cap
If the oil level is between M IN and MAX
marks on the end of dipstick, DO NOT
refill oil. Hot oil may exceed the M AX
mark several millimeters due to thermal
expansion.
If the oil level is at or lower than the MIN
The engine oil consumption is affected by mark, please refill engine oil that
many factors. A new engine reaches the conforms to Chery’s specifications, to the
normal operating specification only after position between M IN and M AX marks
traveling approx. 5,000km. M ore oil might only. For details, see the chapter “Capacity
be consumed when the engine operates and Specification”.
with high load.
Regularly checking the engine oil is
required, e.g. when refueling or before a Please DO NOT use the oil Turn the filler cap counterclockwise and
long-distance journey. additives or engine treating pull out to open it. DO NOT open the filler
compound. It is not only cap as the engine is running.
Stop the vehicle on a level ground before unnecessary, but also damages the
checking the engine oil. Turn off the engine in certain cases, without the Turn the filler cap clockwise until a click
ignition switch and wait for several is heard, which means the filler cap
warranty.
minutes in order to let the oil flow into the closed.
oil sump (it may take longer time when the
out side temperature is low or the normal
working temperature of engine is still Empty oil container must not be
unavailable). DO NOT start the engine at thrown into the household waste. Please
cold state before checking engine oil. use local qua lified waste disposal facilities
Draw out the oil dipstick and clean it with to dispose these items.
flannelette-free cloth. Carefully insert it
94
Repair & Maintenance
Brake Fluid The brake fluid that conforms to Chery’s Engine Coolant Reservoir
specification is available only. Refer to the
chapter “Capacity and Specification”.
Send t he vehicle to Chery’s special service
Please DO NOT let such station as soon as possible to check the
fluid contact your skin or eyes. Use system leakage.
plenty of clean water to wash the
position affected and immediately Ensure the brake fluid refilled absolutely
clean.
see a doctor if such case happens.
95
Repair & Maintenance
Refilling method of coolant: marks when the engine is at cold state. Therefore, please use the coo lant that
counterclockwise turn and apply with meets with Chery’s specification.
If you have to refill it while the engine is
force downward to open the reservoir cap
at hot state, wait for 10 minutes to cool the
for refilling when the engine is at cold
engine, and then screw the reservoir cap
state and static. Coolant amount refilled and refill coolant that meets with the Please DO NOT use coolant
must exceed the M IN mark and lower than
vehicle’s specification. with different colors and
MAX mark. Then screw the reservoir cap
clockwise. specifications.
96
Repair & Maintenance
Power steering fluid that meets with Windscreen Cleaning Fluid Check Wiper Blade
Chery’s specification is required.
Reservoi r
Battery
There is a hole on the battery for checking Slide your fingertip along the edge of the
the battery condition. Recharge or replace The cleaning fluid of windscreen cleaning wiper blade to check its coarseness. Butter,
the battery according to the prompt in the system is supplied by the reservoir. M ix silicone resin and fuel may result the
check hol e. clean water and windscreen cleaner with wiper blade failed to normal work. It
the concentration of 1: 20 if necessary. suggests that using windscreen cleaning
Your vehicle is equipped with a
fluid to clean the blade.
maintenance-free battery. Using other Properly refill windscreen cleaning fluid
model of battery is not recommended. The and screw the reservoir cover well.
current and capacity of new battery must
be the same as the used one or Chery’s
specification. Please consult Chery’s
special service station for proper battery
specification.
97
Repair & Maintenance
Replace Wiper Blade particular when the vehicle travels with
heavy load and high speed. The tire
pressure insufficient may reduce the
stability of vehicle, increase rolling
resistance and qui cken tire weariness, and
lead to accident as well.
If you have to drive on the road edge,
slowly drive the vehicle only. If possible,
the wheels shall vertically approach the The depth of tire tread wear is legally
roadside and avoid upstanding and sharp limited. A wear trip may occur on the tire
edged obstacles. DO NOT scratch the tread after the wear reaches the limit value
lateral wall of tire as parking. of 2mm, which indicates that the
Raise the wiper arm and make it Regularly check whether there are flesh performance and safety of tire reduce
perpendicular to the wiper blade. To cut, foreign material and uneven wear on considerably and the tire must be replaced.
remove the blade, press the retaining clip the tire surface. Uneven wear of tire tread
in the arrow direction and release the indicates that the wheel alignment may be
blade, then pull away the wiper arm in the Follow the local regulations on
wrong. environmental protection to dispose the
reverse direction.
worn tire. Change the winter tire to
summer tire as the road condition
Tire permitted immediately, which can reduce
fuel consumption and noise.
Please check the tire pressure (including
spare tire) after they cool down when
refueling for your safety. Refer to the
Replace Tire
suggested tire pressure in the chapter
“Capacity and Specification” for details. The tires your vehicle used are properly
selected to provide the best operation,
Comply with the correct tire pressure in comfort and safety. The above
98
Repair & Maintenance
specifications on the tire-wheel rim Notes:
combination are suitable for the steel and
The speedometer is subject to the 1. The vehicle speed shall be
aluminu m alloy wheel rim. Please inquire
dimension of tire. If the tire dimension no more than 50km/h while using
Chery’s special service station to learn
(diameter) is different from that of the tire chains. 2. The tire chains shall
whether other kinds of tires and wheel
genu ine one, the exact speed cannot be be removed at once when driving
rims can be used in the vehicle.
indicated. on the non-snowy road.
99
Repair & Maintenance
generator belt shall be checked after the Use cold or slightly-warm water to wash
vehicle travels every 1,000 Km. the vehicle only.
Please turn off the heating
Check the tension of driving belt blower before using the automatic
1. Turn off the ignition switch and take vehicle washer.
out the key.
2. Press the intermediate position of the Wash Vehicle Manually
belt with your thumb (approx. 100N),
and check the flexibility of the belt. IF the vehicle cleaning fluid is used,
please use plenty of clean water to wash,
M ax. p ermitted flexibility: 10mm. and wipe the vehicle with a dry cloth.
3. If the flexibility exceeds the permitted Automatic Vehicle Washer The water from high pressure spray gun
value, please get to Chery’s special may enter in the intake pipe of engine of
service station to have it regulated even inside the engine through the air
The best method to wash a vehicle is to
immediately. intake grill of engine bonnet during
employ the brushless facilities in a good
vehicle-washing shop. The powerful water washing, which harms the engine greatly.
Wash Vehicle flow may damage the painted surface of Therefore, DO NOT aim at the air intake
vehicle in a vehicle-washing shop with grill with the high pressure spray gun
DO NOT throw the cleaning material in high pressure water operation. while washing the vehicle.
the household waste. Please use qualified
local waste disposal facilities.
Slightly step the brake pedal
The vehicle washing area where the several times to remove the moisture
ecological drainage system won’t be from brake lining during driving after
damaged is available only. The most the vehicle is washed.
important factor to protect the painted
surface of vehicle is to use clean water.
100
Repair & Maintenance
Clean Headlamp Paint Removal Treatment
To ensure the permanence of
To avoid damage from the plastic lens of vehicle’s paintwork, remove the For paintwork damage or slight scratch
headlamp, DO NOT use corrosive substances harmful to the painted created by the ballast on the road, please
abrasives or chemical solvents. DO NOT surface in time, such as bird get to Chery’s special service station to
wipe the lamps when the mirror is dry, or droppings, resin, insect residuals, tar have it treated.
use a keen-edge object to clean the lens. spots, etc.
Pai ntwork Protection
Clean Rear Windscreen Clean Wheel Wax your vehicle once or twice every year
When cleaning the rear windscreen, use to keep the paintwork smooth.
It depends on road mileage, clean the
soft cloth to wipe it only in order to avoid wheels once every week in order to avoid
damage from the heating components or the dust accumulating on the brake. Use
radio antenna. DO NOT use the solvents the wheel cleaning agent or warm water When waxing, make sure to
or keen-edge obj ect to clean the and soft sponge to clean wheels. DO NOT prevent waxing agent touch with
windscreen. use abrasive materials to clean them in surface of plastics, or else it will be
order to avoid the damage of specially very difficult to eliminate. M oreover,
Anti-Corrosion of Chassis machined surface. do no wax your vehicle under intense
sunlight.
The vehicle’s chassis has been conducted Cleaning Products
anti-corrosive treatment. Regularly check
the chassis anti-corrosive protection. To get the best effect, please properly use
Please get to Chery’s special service the vehicle care products.
station if necessary.
101
Repair & Maintenance
Leather Fabric Care Clean Radiator
The fins of radiator are
Use the wet cotton cloth and tower to wipe After the vehicle travels for a period of essential to conduct better heat
the leather surface, and dry it with a clean time, the windward side of the condenser conduction. DO NOT brush these
soft cloth. During the normal service and radiator may be jammed by some fins. Otherwise it may damage the
period, it suggests using special curing insects, tree leaves and other foreign fins and reduce the heat conduction.
agent for leather to care the leather once materials. In this case, it will inf luence the DO NOT spray water on hot radiator
every six months. performance of the air conditioner and because the hot air generated will
cooling system, which results the air bring injury.
DO NOT make the leather too wet,
conditioner failure to operate normally,
especially DO NOT make the water Use water to wash the radiator only
and cooling system over-heat and so on.
leaking in the gaps. when the engine stops running and
So it is necessary to clean the radiator and
condenser. cools down.
102
Repair & Maintenance
103
Repair & Maintenance
Maintenance Item Mileage (Km)
5,000 15,000 30,000
Steering tie rod end: Check clearance and t he dust cap whether is damaged ★ ★ ★
Protective sleeve of steering universal joint assy.: Check malposition or damage ★ ★
Hand brake: Check its travel, regulate it if necessary ★ ★
Brake lining/ brake shoe: Check the thickness, replace it if necessary ★ ★ ★
Brake disc/ brake drum: Check if it works normally or is damaged, replace it if necessary ★ ★
Body bottom protector: Visually check whether it is damaged ★
Safety belt: Check whether damaged ★ ★
Toe-in value, wheel camber angle: Check and regulate if necessary ★ ★
Ball pin: Check the clearance ★ ★
Rear shaft rubber hinge: Check whether damaged ★ ★
Universal joint/ front wheel bearing: Check the connection whether loose, with abnormal sound ★
Engine oil sump bolt: Check whether loose and tighten it if necessary ★
Control arm rubber sleeve: Check whether damaged ★ ★
Brake hose: Check whether aged or damaged ★ ★
Brake pipe: Check whether damaged or corroded, and the leakage of all joints ★ ★
Suspension components: Check they are whether abnormally loose, friction or damaged, whether work ★ ★ ★
normally
Joints of fuel system: Check aging, damage, abnormal loose or friction ★
Exhaust system: Check the leakage and damage, regulate or replace it if necessary ★ ★
Steering system: Check the level of power steering fluid, whether the clearance of gear rack of steering ★ ★
wheel is proper, the connection status of all adapting parts, whether the system works normally, repair or
replace it if necessary
Cooling system: Check the level of anti-frozen fluid, check the status of all connection pipes, leakage, ★ ★ ★
replace it if necessary
104
Repair & Maintenance
Maintenance Item Mileage (Km)
5,000 15,000 30,000
Braking system: Check the level of brake fluid, check the status of all connection pipes, leakage and ★ ★ ★
damage, working condition of the system, repair or replace it if necessary
A/C system: Check its pressure whether normal, check leakage, abnormal sound, abnormal odor, and the ★ ★ ★
system whether works normally
Tire (including spare tire): Check the depth of tread, regulate the pressure of tire, check the tightening ★ ★ ★
torque of wheel bolt
Change the position of tire ★
Connection bolt of chassis and body: Check it whether loose, tighten it if necessary ★ ★ ★
Wheel: Check it whether loose ★ ★ ★
Engine idle speed check: Check working state of engine at ideal speed, parameters of electronic fuel ★ ★ ★
injection system and exhaust are whether normal, regulate it if necessary
Trial driving: Check the function of every mechanism is whether normal, regulate it if necessary ★ ★ ★
Note: For manual transmission, replace the transmission gear oil once every one (1) year or 30,000km road mileage, and replace the brake
fluid once every two (2) years or 50,000km road mileage.
105
Repair & Maintenance
Owner: _____
CHERY
First 5000km Company (name): _
Address: _______________________
Maintenance Card Tel: _______________________
E-MAIL: _____________________
Date: ____ Purchase date: _____
Purpose: __________
Mileage: _ Service Station License plate number: _____
(Seal)
Purpose: __ Vehicle data
106
Repair & Maintenance
First 5000km
First 5000km Maintenance Card Maintenance Card
Date: __________ Mileage: _________ Date: ____________
Checking item: Yes No Checking item: Yes No
() () 10. Check the tension of generator () () Mileage: ___
1. Check the leakage of lubricating and air conditioner belt, then adjust
system, cooling system and fuel if necessary.
system. Purpose: _
2. Replace engine oil and oil filter. () () 11. Check the hinge and latch of () ()
engine hood. License plate number: _
3. Chec k coolant level, and add () () 12. Chec k the leakage of air () ()
coolant or adjust its density if conditioning system.
necessary.
4. Chec k the leakage of trans mission () () 13. Check the leakage of pow er () () Service Station (seal): __
steering line, then add pow er
5. Chec k the damage of the dust cap () () steering oil if necessary.
for steering tie rod.
6. Check the damage of dust cap for () () 14. Check the assembly and () ()
constant velocity universal joint. damage of the dust cap for steering
universal joint. Owner (signature): ___
7. Check the leakage of brake fluid, () () 15. Chec k the positions of manual () ()
and chec k the damage of brake line. trans mission shaft crank to ensure
smooth operation of each shift.
8. Chec k the function of brake pumps. () () 16. Check the joint bolts for () ()
fastening chassis and vehicle body
9. Check the tire inflation pressure to
ensure it confor ms to the specification. () () to see w hether they are loose or
not.
107
Repair & Maintenance
Maintenance Record
Regular maintenance is made according to the specified items in the regular techni cal maintenance of Chery Riich R2 (M ileage and
time above are subject to the requirement, whichever is first)
108
Repair & Maintenance
For 25,000Km of road mileage For 30,000Km of road mileage For 35,000Km of road mileage
or within six (6) months after the or within six (6) months after or within six (6) months after
last service, the 5,000Km the last service, the 30,000Km the last service, the 5,000Km
maintenance items are available maintenance items are available maintenance items are available
Regular maintenance is made according to the specified items in the regular technical maintenance of Chery Riich R2 (M ileage and
time above are subject to the requirement, whichever is first)
109
Repair & Maintenance
Regular maintenance is made according to the specified items in the regular techni cal maintenance of Chery Riich R2 (M ileage and
time above are subject to the requirement, whichever is first)
110
Repair & Maintenance
Regular maintenance is made according to the specified items in the regular technical maintenance of Chery Riich R2 (M ileage and
time above are subject to the requirement, whichever is first)
111
Repair & Maintenance
Regular maintenance is made according to the specified items in the regular technical maintenance of Chery Riich R2 (M ileage and
time above are subject to the requirement, whichever is first)
112
Repair & Maintenance
For 85,000Km of road mileage For 90,000Km of road mileage or For 95,000Km of road mileage or
or within six (6) months after the within six (6) months after the last within six (6) months after the last
last service, the 5,000Km service, the 30,000Km service, the 5,000Km maintenance
maintenance items are available maintenance items are available items are available
Regular maintenance is made according to the specified items in the regular technical maintenance of Chery Riich R2 (M ileage
and time above are subject to the requirement, whichever is first)
113
Repair & Maintenance
114
Repair & Maintenance
115
Quality Warranty Service
116
Quality Warranty Service
Warranty for Complete license issued date. If the purpose of Plastic parts, rubber parts, switches, lamps,
vehicle changes within the warranty paintwork flake/ crack:
Vehicle period, the warranty duration and mileage 12 months/ 20,000km
concerned does not alter.
Every Chery Riich R2 sold by an Quality warranty period of wearing
Within the warranty period, if the vehicle
authorized sales service enter can enjoy parts (limited to original quality
is subject to regular maintenance specified
the conditional quality warranty. Within problems only) is 3 months or 5,000km
by Chery Automobile Co., Ltd. while the
the warranty, if the quality defect of the complete vehicle or some parts have
vehicle occurs under normal operation and Wearing parts include: bulbs, glass
defect(s) and they are covered by the
maintenance, it is covered by the warranty, products, tires, brake shoes, clutch lining,
quality warranty, please get to Chery’s
and the owner does not pay for the spark plug, wiper blade, air cleaner, oil
special service station to have your vehicle
maintenance and repair. However, the cleaner, fuel cleaner, high-vo ltage cable
checked and repaired.
vehicle must be repaired by Chery’s and antenna.
special service station.
Quality Warranty Period for
The quality warranty period for Special Parts (limited to
non-operational Chery Riich R2 is
thirty-six (36) months or 60,000km original quality proble ms
accumulated road mileage while the only):
warranty period for the operational vehicle
is twelve (12) months or 100,000km Control arm ball pin, tie rod ball, steering
accumulated road mileage, whichever is universal joint, oxygen sensor, clutch plate,
first (i.e. one of both conditions comes, the damper, damper rubber sleeve, dust cap:
vehicle is not subject to the quality 12 months/ 30,000km
warranty), and the warranty period is Battery: 12months/ 50,000km
calculated starting from the earliest date Horn: 6 months/ 30,000km
among the date that the owner received the Ribbed belt, engine timing belt, generator
vehicle, the owner information uploaded belt:
date, the invoice date of purchase or 12 months/ 50,000km
117
Quality Warranty Service
3 months/ 5,000km damaged parts in order to clarify what condition of the vehicle, the owner shall
Parts without warranty include: fuse, truly happened. use parts and components (genuine spare
lubrication oil (grease), brake fluid, low parts) provided by Chery Automobile Co.,
The replacement and repair for parts
power of battery, engine coolant, power Ltd. and Chery’s special service station
within warranty period will not extend the
steering fluid, engine oil, etc. will offer you the genuine spare parts
warranty period of complete vehicle or
purchasing service.
parts.
3) Chery Automobile Co., Ltd. will not
The replaced parts within warranty period
For the warranty period of are subject to Chery’s Automobile Co., be responsible for any direct or
wearing parts and special parts, it is Ltd. indirect damage due to refitting or
calculated on the duration and additional installation of various
mileage, whichever is first. The equipment by the owner himself,
warranty period for other parts is the Items not covered by especially refitting or additional
same as the complete vehicle. warranty installation of such system involving
the product safety as electrical,
braking, steering and other systems.
1. The following defects are not covered
by the quality warranty: 4) Defects due to no routine examination
Coverage of Warranty or regular maintenance conducted as
1) Defects occurred in the vehicle which
required, or the examination, repair
Comply with the regulations specified in are repaired or maintained by the
and maintenance conducted by the
the instruction manual to use, repair and owner himself or by the service station
service station other than Chery’s
maintain your vehicle. And bring this other than Chery’s special service
station. special service station.
manual that can prove your vehicle has
been regularly checked and repaired. Note: To ensure the proper operating
2) Chery Automobile Co., Ltd. will not
condition of the vehicle, the owner has
For quality defects and damaged caused be responsible for any direct or
responsibility to conduct necessary
by product design, manufacture, assembly, indirect damage due to installed parts
and components are not produced or examination, repair and maintenance. For
raw material detect and ot her factors, if an example, the engine oil has the crucial
owner reclaims the quality warranty, he/ provided by the company.
functions such as lubricating, cooling the
she shall protect the original status of the Note: To ensure the proper operating engine and rust prevention, etc. The
118
Quality Warranty Service
engine oil in service will be gradually Note: The prerequisite for the warranty is Fox example:
contaminated, corroded or degenerated. So to properly use the genuine spare parts and
Defects due to driving in harsh area or
if the oil continues in service for a long specified grease so as to ensure the normal
racing.
time, it may burn out the engine. And such operation of the vehicle. So, if the
defects due to the shortage of proper non-genuine spare parts are used, or they Overloading or excessively pressing
examination and maintenance, Chery will are genuine spare parts, but not applicable chassis spring.
not be liable for the warranty service. to the vehicle, or the grease not specified
Engine failure caused by the operation
in the manual is employed, all of these
The instruction manual specifies the with overload, and the excess of the
may influence the vehicle’s original
necessary maintenance items. After such transmission limit specified in the manua l
items are executed, please record the performance and decreases its durability.
when the vehicle travels at high speed.
results in the manual, and keep it carefully. For example, the oil cleaner not specified
2. The following symptoms will not be
When accepting warranty service, you by Chery is utilized and then it leads to the
deemed as defects with the warranty.
must bring forth the manual. cleaner jammed and the bearing burnt.
1) The symptoms caused by the wear or
5) Severe defects result from the 7) Defects caused by the malfunction of
the long period of service. (Natural
problems that owner should have the vehicle and improper use of the
fading or degeneration of painted
discovered and handled, but ignored. M anual or the overuse of the vehicle
surface, plating surface, resin parts,
Note: Fox example, although it has been that exceeds the vehicle’s capabilities
etc.)
specified in the specification (the
found that engine oil alarm lamp gives a
vehicle travels as a racing vehicle with Note: Among parts consisting of an
warning, or the driver feels something
the overload, the engine overload, automobile, some of them (e.g. clutch disc)
abnormal (noise, vibration), the vehicle
excessive loading capacity, passenger are subject to be continuously worn with
has not been overhauled in time during
overload, excessive driving speed, the driving and repeated operation.
routine inspection. And it continues in
etc).
service and makes failures worse. In addition, the brake lining and other
Note: The malfunction of the vehicle and parts which fulfill their functions by
6) Defects caused by the use of products
improper use of the M anual or the overuse wearing themselves, those consumptive
other than the genuine spare parts and
of the vehicle that exceeds the vehicle’s parts for daily running and the grease such
specified grease (includ ing engine oil,
capabilities specified in the specification as engine oil or coolant which plays the
brake fluid, transmission oil, and fuel).
are mainly as follows: role of lubricating and cooling, will be
119
Quality Warranty Service
substantially consumed and degenerated 1) Defects caused by exterior reasons daily driving. Owners shall pay the costs
with the traveling of vehicle. The painted such as coal smoke, medicine, bird for the replacement and supplement of
surface of exterior plate and interior droppings, oil acid rain, gravel, scrap such products by themselves.
instrument panel surface would gradually iron, ash falls and salt and so on.
2) Expenditure for overhaul and regular
tarnish and slowly fade.
Note: Defects caused by exterior reasons replacement of parts and component s
The consumption generated due to daily such as glass broken by splashing grovels specified by Chery.
running and operating as well as the during traveling, compartment scratched,
Note: The consumption and degeneration
fading symptom will not be covered by the paintwork fading resulted due to the bird
are inevitable during the use of vehicle. So
warranty. dropping or acid rain attaching.
the proper overhaul and daily/ regular
2) In general, those perceived 2) Defects caused du e to natural disasters inspection must be done on schedule
occurrences that will not affect the such as earthquake, windstorm, flood, according to the service condition.
vehicle quality and functions. fire or other accidents.
3) Expenditure for your vehicle repaired
(Operation fee, noise, etc.)
4. Chery will not be liable for the in service stations other than Chery’s
Note: Noise and vibration sometimes are expenditures in case of the following special service station.
caused by abnormal vehicle’s condition conditions.
Chery will not be liable for the repair cost
while it is possible that normal operation
1) Some parts of vehicle are wearing in the service stations other than Chery’s
also causes noise and vibration
parts such as friction lining, wiper special service station.
occasionally. In the case, the vehicle’s
blade, spark plug, cleaner, tire, bulb,
quality and function have no problem. For 4) Expenditure caused by normal
lubricating oil (grease), brake fluid,
example, the noise caused when the brake inspection and adjustment (fuel
low power battery, engine coolant,
pedal is stepped on mostly comes from consumption, CO content, lighting,
power steering fluid, oil. The costs
friction (usually called the braking noise) inspection and adjustment of
generated due to normal consumption
while it is not the functional problem. four-wheel calibrating mechanism,
of these parts and the expenditures
dy namic balance of tires, etc.)
3. The following defects caused by spent on replacement and supplement
exterior reasons are not the material of grease or oil. 5. Additional expenses
and manufacturing problems, without
Note: Wearing parts and grease will be The economic loss or additional expenses
the warranty.
consumed and degenerated along with caused due to the vehicle failed being
120
Quality Warranty Service
service are not covered in the quality whichever is first.
warranty. For instance, it includes:
Warranty coverage and items not covered
The economic loss and time loss caused by the warranty refers to the regulations of
by the vehicle failed being service warranty for a complete vehicle.
Expense on the vehicle storage In the quality warranty period for a
Expense on the vehicle rent or lease complete vehicle, parts are replaced and
installed by Chery’s special service station
Expense on accommodation, food or other for free. The quality warranty period of
items concerned replaced parts is the remaining time of
Other related loss warranty for the complete vehicle, which
will be ended with the warranty for the
complete vehicle ended.
Spare Parts Warranty
Please consult local Chery’s special
service station if you have any doubts on
Spare parts that are bought and installed in the above regulations.
Chery’s special service station and
supplied by Chery Automobile Co., Ltd.,
the warranty period is 6 months or 20,000
accumulated road mileage, calculated
from the date of purchasing and
installation. Among them, the warranty
period for wearing parts (bulb, glass
products, air cleaner element, fuel cleaner,
oil cleaner, wiper blade, tire, clutch lining/
brake shoe, spark plug and high-voltage
cable) is 3 months or 5,000km
accumulated road mileage. All warranty
period listed above is subject to the one
121
Capacity and Specification Parameters
123
Capacity and Specification Parameters
Vehicle Identification Description
124
Capacity and Specification Parameters
VIN Vehicle Nameplate in case of refueling. The fuel additives
can prevent the engine from corrosion
The VIN code of Chery Riich 2 vehicle and encrustation and clean the fuel
is printed on the right side of the front system.
panel upper roof drip channel (as The Chery authorized service station
shown in the above figure). has the fuel additives authorized by the
Chery Company, and the personnel in
Engine Number the station are familiar with the use of
the additives and the engine
The SQR473F series engine number is encrustation treatment method, and
located on cylinder block flange beside offer you the best service with all our
the oil filter of the engine exhaust side, heart.
(as shown in the following figure). The vehicle nameplate is fixed as
shown in the above figure. The fizzle sound can be heard when the
furl filler cap opens. This is normal.
127
Capacity and Specification Parameters
Capacity
Capacity (L)
128
Capacity and Specification Parameters
Mass Parameters
Items Parameters
129
Capacity and Specification Parameters
Wheel and Tire Tightening torque of wheel bolt
The tightening torque of wheel bolt is 110±10 Nm.
Tire pressure
Wheel
Before your journey begins, check the tire pressure (cold state)
(DO NOT forget to check the pressure of spare tire).
M odel
Tire pressure (cold tire) (kPa)
Wheel rim 5J 14
Items Front Rear Wheel Spare Tire Tire 165/70R14×85H
Wheel
Half-load 250 250 400
Full load 220 280
Engine Data
M odel SQR473F
Type In-line, water cooling, four-stroke, in-line DOHC, 16 valves and multipoint EFI
Cylinder Diameter mm 73
Piston Stroke mm 77.5
Displacement ml 1,297
Compression Ratio 10 : 1
Rated power (net power) 61
kW
Rated RPM r/min 6,000
M ax. Torque N·m 114
M ax. Torque Speed r/min 3,800-4,500
M in. Fuel Consumption 280
g/kw·h
131
Capacity and Specification Parameters
Vehicle Dimension
132