Professional Documents
Culture Documents
com
PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE OT AND
MUST BE RETURNED TO BOE HF UPON ITS REQUEST.
TITLE : HV320WXC
HV320WXC-100
100
Product Specification
Rev. A
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
REVISION HISTORY
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Contents
No ITEM Page
REVISIONS HISTORY 2
CONTENTS 3
1 GENERAL DESCRIPTION 4
1.1 Introduction
1.2 Features
1.3 Applications
1.4 General Specification
2 ABSOLUTE MAXIMUM RATINGS 6
3 ELECTRICAL SPECIFICATIONS 7
3.1 TFT LCD Module
3.2 Inverter
4 INTERFACE CONNECTION 9
4.1 Module Input
p Signal
g & ppower
4.2 LVDS Interface
4.3 Inverter Input Signal & Power
5 SIGNAL TIMING SPECIFICATIONS 12
5.1 Timing Parameter
5.2 Signal Timing Waveform
5.3 Input Signals, Basic Display Colors & Cray Scale Of Colors
5.4 Power Sequence for LCD
5.5 Power Sequence for Inverter
6 OPTICAL SPECIFICATIONS 17
7 MECHANICAL CHARACTERISTICS 19
8 RELIABLITY 20
9 PRODUCT SERIAL NUMBER 21
10 PACKING INFORMATION 22
11 HANDING & CAUTIONS 24
12 APPENDIX 25
B2010-6011-O(3/3) A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1.1 Introduction
HV320WXC-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 31.51 inch diagonally
measured active area with WXGA resolutions (1366 horizontal by 768 vertical pixel array).
Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and
this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a
low reflection and higher color type.
RGB(Mini-LVDS)
Source Driver Circuit
S1 S1366
G1
+12.0V
Gate Driver Cirrcuit
Timing Controller
LVDS CN1
5pair
[LVDS Rx & Mini-LVDS
(30pin) Tx integrated]
Option TFT - LCD Panel
#9 (1366 Ý RGB Ý 768 pixels)
+24.0V
Inverter Back light Assembly
2pin x 4CNs (High)
+24.0V (CN2) (4 U_CCFL)
1.2 Features
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1.3 Application
Parameter Specification
p Unit Remarks
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. LCD Module Electrical Specifications > [VSS=GND=0V]
Note : 1) Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ć max. and no condensation of water.
ڀڋړ
ڋڑ
ڀڋڑ
ڋڐ ۀۂڼۍۊۏڮ
ڸڣڭڄڀڃڶٻ۔ۏۄڿۄۈېڣ
ڽۇېڝٻۏۀڲ
ڸڞڶٻۀۍېۏڼۍۀۋۈۀگ
ڋڏ
ڀڋڏ
ۉۊۄۏڼۍۀۋڪ
ڋڎ
ڋڍ
ڋڌ
ڋ
ڀڋڌ
ڋڍڈ ڋ ڋڌ ڋڍ ڋڎ ڋڏ ڋڐ ڋڑ ڋڒ ڋړ
¶ڶٻۀۍېۏڼۍۀۋۈۀگٻڽۇېڝٻ۔ۍڟCڸ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Values
Parameter Symbol Unit Notes
Min Typ Max
Power Supply Input Voltage VDD 10.8 12 13.2 Vdc
Power Supply Ripple Voltage VRP 300 mV
Power Supply Current IDD 200 250 350 mA 1
Power Consumption PLCD 2 3 5 Watt
Rush current IRUSH - - 2.0 A 2
Differential Input High
VLVTH +100 mV
Threshold Voltage
LVDS
Differential Input Low
Interface VLVTL -100 mV
Threshold Voltage
Common Input Voltage VLVC 1.0 1.2 1.4 V
Input High Threshold
VIH 2.7 - 3.3 V
CMOS Voltage
Interface Input Low Threshold
VIL 0 - 0.7 V
Voltage
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=12.0V, Frame rate=60Hz and
Clock frequency = 73.9MHz. Test Pattern of power supply current
a) Typ : Black Pattern
b) Max : Sub Dot Pattern
2. The duration of rush current is about 2ms and rising time of Power Input is 1ms(min)
White : 255Gray
Black : 0Gray
Mosaic Pattern(8 x 6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
3.2 Inverter
< Table 4. Inverter Electrical Specifications >
Values Note
Parameter Symbol Condition Unit
Min. Typ. Max. s
I
Input
tVVoltage
lt VBL 22 8
22.8 24 0
24.0 25 2
25.2 V
Input Current IBL Vadim=3.3V - 3.2 3.5 A 1
Rush current IRUSH VBL= 24V - - 6 A
Power
PBL Typ Luminance - 77 85 Watt
Consumption
Lamp ON = High 2 33
3.3 5 V
B/L on/off control VON/OFF
Lamp OFF =Low 0 - 0.8 V
Min. Luminance 0
Analog Dimming ADIM V
Max. Luminance 3.3
PWM Frequency FPWM 140 190 240 Hz
High Level 3.0 3.3 3.6 V
PWM Level
Low Level 0 - 0.3 V
PWM Duty DPWM 10 - 100 % 2
Life Time 50,000 - - Hrs 3
Notes: 1.The specified current and power consumption are under the typical supply Input voltage,
24V. It is total power consumption.
2. High-duty = On/(On+Off) * 100
v v
3. The life time of a Lamp, 50,000Hrs, is determined as the time at which luminance of the
lamp is 50% compared to that of initial value at the typical lamp current on condition of
continuous operating at 25 r 2¶C.
B2010-6011-O(3/3) A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
< Table
T bl 55. LCM Module
M d l IInput C
Connector Pi
Pin C
Configuration
fi i >
Pin No Symbol Description Pin No Symbol Description
1 VDD Power Supply +12.0V 16 RX1+ LVDS Receiver Signal(+)
2 VDD Power Supply +12.0V 17 GND Ground
3 VDD Power Supply +12.0V 18 RX2- LVDS Receiver Signal(-)
4 VDD Power Supply +12.0V 19 RX2+ LVDS Receiver Signal(+)
5 GND Ground 20 GND Ground
6 GND Ground 21 RCLK- LVDS Receiver Clock Signal(-)
7 GND Ground 22 RCLK+ LVDS Receiver Clock Signal(+)
8 GND Ground 23 GND Ground
9 LVDS_SEL ‘H’=JEIDA , ‘L’or NC= VESA 24 RX3- LVDS Receiver Signal(-)
10 NC No Connection 25 RX3+ LVDS Receiver Signal(+)
11 GND Ground 26 GND Ground
12 RX0- LVDS
V S Receiver
ece ve Signal(-)
Sg () 277 NC
C Noo Co
Connection
ec o
13 RX0+ LVDS Receiver Signal(+) 28 NC No Connection
14 GND Ground 29 GND Ground
15 RX1- LVDS Receiver Signal(-) 30 GND Ground
Notes : 1. NC(Not Connected) : This pins are only used for BOE internal operations.
2. Input Level of LVDS signal is based on the IEA 664 Standard.
3. LVDS_SEL : This pin is used for selecting LVDS signal data format.
If this Pin : Low (GND) or Open (NC) Æ Normal NS LVDS format
Otherwise : High (3.3V) Æ JEIDA LVDS format
Sequence : On = Vdd LVDS Option Interface signal
Off = Interface signal LVDS Option Vdd
Rea view
Rear ie of LCM
1 IS100-L30B-C23 (UJU) 30
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ITEM S b l
Symbol Mi
Min T
Typ M
Max U it
Unit N t
Note
Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
tCLK
DCLK 0.5 VDD
Valid data
First data Invalid data Pixel data Pixel data Invalid data
Valid data
Second data Invalid data Pixel data Pixel data Invalid data
DE(Data Enable)
tHP
HSync
tHV
DE(Data Enable)
tVP
VSync
tVV
DE(Data Enable)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
5.3 Input Signals, Basic Display Colors & Gray Scale Of Colors
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
shall be as shown in below
WU`}kk WU`}kk
wGz WUX}kk WUX}kk
}kk W}
{X
{\ {]
{Y
}
p z
O p k P W}
{Z {[
is|GvuVvmmG
OG}vuVvmmGP W}
Values
Parameter Units
Min Typ Max
T1 0.5 - 30 ms
T2 0.1 - 150 ms
T3 200 - - ms
T4 0 - - ms
T5 0 - 300 ms
T6 1 - - s
Notes:
1. When the power supply VDD is 0V, Keep the level of input signals on
the low or keep high impedance.
2. Do not keep the interface signal high impedance when power is on.
3. Back Light must be turn on after power for logic and interface signal are valid.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
WU`}kk WU`}kk
wGz
w z WU_}isO P
WUX}kk
}is W}
{]
{X
{\
{Y
}
kGz
}kpt W}
{Z {[
is|GvuVvmmG
OG}vuVvmmGP W}
Values
Parameter Units
Min Typ Max
T1 20 - - ms
T2 500 - - ms
T3 0 - - ms
T4 0 - - ms
T5 10 - - ms
T6 - - 10 ms
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of T= 0q and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then
to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR)
is defined mathematically.
3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with
all pixels in the view field set first to white. This measurement shall be taken at the locations
shown in FIGURE 2 for a total of the measurements per display.
4. The White luminance uniformity on LCD surface is then expressed as :
ԩY = ( Minimum Luminance of 5points / Maximum Luminance of 5points ) * 100
(See FIGURE 2 shown in Appendix).
5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral
data measured with all pixels first in red, green, blue and white. Measurements shall be made
at the center of the panel.
6. The electro-optical response time measurements shall be made as FIGURE 3 shown in
Appendix by switching the “data” input signal ON and OFF. The times needed for the
luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
FIGURE 4 (located in Appendix) shows mechanical outlines for the model HV320WXC-100.
Other parameters are shown in Table 12.
7.2 Mounting
See FIGURE 5. (shown in Appendix)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
The Reliability test items and its conditions are shown in below.
Period : X, Y, Z 30 min
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ڋڋڌڈڞڳڲڋڍڎڱڣ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Seal the box and stick label to the Put cover pad on top of
assigned area the box
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
HV320WXC- 100 [
WWWWWWWWWWWWW YWXWUW[UY_U
WW W W WW W W WWWWW
{ n s t p{ltTjvkl z
FG CODE
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
12.0 APPENDIX
ٻڄ ۈ ھ ڋ ڐٻ ژٻ ڧڃ
1/2V
3/4V
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
گ
ۍگ ہگ
ۇڼھۄۏ ۋ ڪ ڈ ۊۍۏ ھۀۇ ڠ
ۀێۉ ۊ ۋێۀۀ ڭ
ڀڋڋڌ
ڀڋڔ
ڀڋڌ
ڀڋ
ۀ ۈۄگ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com