Professional Documents
Culture Documents
ASTM A351 Castings, Austenitic, Austenitic-Ferritic (Duplex)
ASTM A351 Castings, Austenitic, Austenitic-Ferritic (Duplex)
This standard has been approved for use by agencies of the Department of Defense.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
--`,`,,``````````,,,`,,,`,`,``,-`-`,,`,,`,`,,`---
--`,`,,``````````,,,`,,,`,`,``,-`-`,,`,,`,`,,`---
A 351/A 351M
Vanadium ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.10– ... ... ... ... ... ... ...
0.30
Nitrogen ... ... ... ... 0.10– . . . ... ... ... ... ... ... ... ... ... ... ... 0.18– . . . 0.10– 0.20– ... 0.08– ... 0.18– 0.08– . . . 0.20–
3
Copper ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 3.0– 0.75 2.75– . . . ... ... ... ... 0.50– . . . ... 0.5–
4.0 max 3.25 1.00 1.0
Tungsten ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.5–
1.0
Iron ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Bal ... ...
A
% Cr + 3.3 % Mo + 16 % N $ 40.
B
Grade CF8C shall have a columbium content of not less than 8 times the carbon content but not over 1.00 %.
C
Grade CF10MC shall have a columbium content of not less than 10 times the carbon content but not over 1.20 %.
TABLE 3 Tensile Requirements
CF3 CF- CF8 CF- CF- CF- CF- CF- CF- CF10 CF- CH8 CH10 CH20 CK20 HK30 HK40 HT30 CF- CN- CN- CD- CE- CG CG- CF10S- CT- CK- CE20N CG- CD3M-
3A 8A 3M 3MA 8M 3MN 8C 10M 10MC 7M 3MN 4MCu 8MN 6M- 8M MnN 15C 3M- 3M WCuN
(J92- MN CuN (J92-
901) 999)
4
A 351/A 351M
SUPPLEMENTARY REQUIREMENTS
The following supplementary requirements shall not apply unless specified in the purchase order. A
list of standardized supplementary requirements for use at the option of the purchaser is included in
Specification A 703/A 703M. Those which are ordinarily considered suitable for use with this
specification are given below. Others enumerated in Specification A 703/A 703M may be used with
this specification upon agreement between the manufacturer and purchaser.
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection
with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such
patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible
--`,`,,``````````,,,`,,,`,`,``,-`-`,,`,,`,`,,`---
technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your
views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at
610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website (www.astm.org).