Professional Documents
Culture Documents
5G2
WDX8G2
WDX10G2
USER MANUAL
Installation Instructions | Owners Manual
Due to continuous improvement of the product, specifications are subject to change without notice.
Introduction
Congratulations on your purchase of a DB Drive state-of-the-art subwoofer. Your selection of a
DB Drive car audio product indicates a true appreciation of fine musical reproduction. Whether
adding to an existing system or including your DB Drive subwoofer in a new system, you are
certain to notice immediate performance benefits.
Recommendation
A power subwoofer’s performance is only as good as its installation. Proper installation will max-
imize the system’s overall performance. It is recommended that you have our product installed
by an authorized DB Drive retailer. However, if you decide to install it yourself, please carefully
read through this manual and take your time to do a quality installation.
IMPORTANT!
Before making any connections, disconnect the car’s battery until the installation is
completed to avoid possible damage to the electrical system.
WARNING!
Exposure to high power sound system can cause hearling loss or damange. Listening
to your system at loud levels while driving will impair your ability to hear traffic sounds
and emergency vehicles. Use common sense when listening to your system.
2
PRODUCT SPECIFICATIONS
TS SPECS WDX6.5G2 WDX8G2 WDX10G2
FS......................................................52.4Hz............................. 44.3Hz...........................46.1Hz
Res.................................................... 43.6 Ω...............................88.9 Ω.............................95.0 Ω
Re.........................................................6.4 Ω..................................6.4 Ω............................... 6.4 Ω
Qms......................................................4.33...................................5.02................................ 5.48
Qes........................................................0.71...................................0.59................................ 0.62
Qts.........................................................0.61...................................0.53................................ 0.56
Rms.................................................7.2kg/s.......................... 10.5kg/s.......................10.8 kg/s
Cms..........................................0.10mm/N......................0.07mm/N.................. 0.06 mm/N
Mms................................................94.2 gr............................190.1gr.........................203.9 gr
BL.................................................. 16.7N/A...........................23.9N/A........................24.7 N/A
SPL.................................................. 79.4dB............................. 79.3dB...........................83.3dB
VAS........................................................ 2.8L...................................3.9L.................................8.9L
Rp...................................................... 35.7 Ω...............................50.1 Ω.............................50.8 Ω
Lp....................................................24.1mH...........................31.6 mH........................ 31.0 mH
Cp.................................................. 624.7uF.......................... 537.0 uF........................532.8 uF
Le....................................................2.68mH...........................3.57 mH........................ 3.65 mH
Xmax................................................15mm...........................17.5mm............................20mm
SD.............................................. 21.65sq.in......................33.18 sq.in................... 53.46sq.in.
Driver Displacement.............. 0.05cuft............................0.08cuft........................0.14cuft.
CALCULATING ENCLOSURES
It is recommended to build your enclosure from at least 3/ 4” thick MDF (medium density
fiberboard). Make sure the enclosure is sealed airtight.
Next subtract 1.5 from each of the outside measurements of the box.
Width Height Depth
12 - 1.5 = 10.5 14 - 1.5 = 12.5 9 - 1.5 = 7.5
Multiple the new totals (H x W x D) Example: 10.5 x 12.5 x 7.5 = .5696
Next you must convert cubic inches into cubic feet. To do this, you must
divide the cubic inch total by 1728”. Example 984.375 ÷ 1728=.5696 cubic feet.
RECOMMENDED ENCLOSURES
Sealed Ported
WDX6.5G2
Woofer Cut-out: 5.98 in. (152 mm.)
Mounting Depth: 4.55 in. (115.5 mm.)
Recommended Sealed Box: 0.69cuft.
Recommended Vented Box: 0.88 cuft.
• Vent Area: 2.5” round vent or 5 square inches
• Vent Length: 11” long
• Tuning: 36Hz
Dynamic Power Handling : 1500 Watts
Nominal Power Handling : 750 Watts
WDX8G2
Woofer Cut-out: 7.32 in. (186 mm.)
Mounting Depth: 5.63 in. (143 mm.)
Recommended Sealed Box: 0.9 cuft.
Recommended Vented Box: 1.13 cuft
• Vent Area: 3.5” round vent or 10 square inches
• Vent Length: 22” long
• Tuning: 33Hz
Dynamic Power Handling : 1500 Watts
Nominal Power Handling : 750 Watts
WDX10G2
Woofer Cut-out: 9.40 in. (239 mm.)
Mounting Depth: 6.38 in. (162 mm.)
Recommended Sealed Box: 1.38cuft.
Recommended Vented Box: 1.77cuft
• Vent Area: 4” round vent or 17 square inches
• Vent Length: 17” long
• Tuning: 33Hz
Dynamic Power Handling : 2000 Watts
Nominal Power Handling : 1000 Watts