Professional Documents
Culture Documents
Reporting Problems
This document lists the technical specifications, operating limits, and shipping and storage
requirements for a DAE8S, which is a drawer-type disk array enclosure (DAE) that holds up
to 120 disks.
Topics include:
l Technical specifications.............................................................................................2
l System operating limits............................................................................................. 4
l Shipping and storage requirements........................................................................... 7
Technical specifications
Technical specifications include system power requirements, size, drive, and cabling
information.
Power requirements
The input current, power (VA), and dissipation per enclosure listed in this document are
based on measurements of fully configured enclosures under worst-case operating
conditions. Use the operating maximum values to plan the configuration of your storage
system. These values represent either:
l values for a single power supply line cord, or
l the sum of the values shared by the line cords of the combined power supplies in the
same enclosure, with the division between the line cords and supplies at the current
sharing ratio (approximately 50% each).
A failure of one of the combined power supplies per enclosure results in the remaining
power supply supporting the full load. You must use a rackmount cabinet or rack with
appropriate power distribution, and have main branch AC distribution that can handle
these values for each enclosure in the cabinet.
EMC provides a power and weight calculator. Use this calculator to refine the power and
heat values in Table 1 on page 2 to more-closely match the hardware configuration for
your system.
Requirement Description
AC line voltage 200 to 240 V AC ± 10%, single-phase, 47 to 63 Hz
In-rush current 30 A max for ½ line cycle, per line cord at 240 V AC
Startup surge current 25 A rms max for 100 ms, per line cord at any line voltage
Note: Ratings assume a fully configured DAE8S that includes 4 power supplies, 2 LCCs, and 120
disk drives.
2
Technical Specifications and Operating Limits
Notes
1. Ratings assume a fully loaded DAE that includes four power supplies, 2 LCC's and
120 disk drives (10W DC per disk drive) . For specific product configuration power
numbers, refer to the EMC power calculator at https://powercalculator.emc.com. The
power calculator only supports products with an input voltage of 200-240 VAC.
2. All power figures shown represent max normal operating numbers with the chassis
running in a normal 20°C to 25°C ambient temperature environment.
3. This chassis is equipped with adaptive cooling. The adaptive cooling feature
increases the overall power consumption of the chassis by the following values listed
when the ambient temperature is above 35°C. .
l Power increase = 250VA (225W);
l Heat dissipation increase = 8.99 x 105 J/hr., (853 Btu/hr.) max;
l The adaptive cooling additional power increase should be added to the overall power
consumption when the ambient operating temperature is above 35°C.
Requirement Description
Height 5.2 in (20.0 cm)
Note
l Full system weight. Weight does not include mounting rails. Allow 2.3-4.5 kg (5-10 lb)
for a rail set.
l Dimensions are of enclosure chassis only. Dimensions do not include bezel mounting
hardware.
Requirement Description
Ambient temperature 50°F to 95°F (10°C to 35°C)
Note
The allowable relative humidity level is 20 to 80% noncondensing. However, the recommended
operating environment range is 40 to 55%. To minimize the risk of hardware corrosion and
degradation, we recommend lower temperatures and humidity for data centers with gaseous
contamination such as high sulfur content. In general, the humidity fluctuations within the data
center should be minimized. We also recommend that the data center be positively pressured
and have air curtains on entry ways to prevent outside air contaminants and humidity from
entering the facility. For facilities below 40% relative humidity, we recommend grounding straps
when contacting the equipment to avoid the risk of Electrostatic discharge (ESD), which can harm
electronic equipment.
NOTICE
For systems mounted in a cabinet, the operating limits listed above must not be
exceeded inside the closed cabinet. Equipment mounted directly above or below an
enclosure must not restrict the front-to-rear airflow of the storage system. Cabinet doors
must not impede the front-to-rear airflow. The cabinet must exhaust air at a rate that is
equal to or greater than the sum of the exhaust rates of all the equipment mounted in the
cabinet.
Airflow
The enclosure uses an adaptive cooling algorithm that increases/decreases fan speed as
the unit senses changes to the external ambient temperature. Exhaust increases with
ambient temperature and fan speed, and is roughly linear within recommended operating
parameters. Note that the data points in the table below are typical, and were measured
without cabinet front/rear doors that would potentially reduce front-to-back air flow.
4
Technical Specifications and Operating Limits
Environmental recovery
The DAE uses two temperature thresholds to trigger automatic shutdown events.
If the system detects three ...then the system does The system restores power
or more disk drives: this: to the disk drives when...
≥141.8°F (61°C) for 18 hours the LCC performs an orderly The system ambient
+ 5 minutes, shutdown that saves cached temperature ≤104°F (40°C)
data before shutting down
≥149°F (65°C) for ≥ 5 minutes,
power to all disk drives. LCCs
remain powered on.
Environmental recovery 5
reactivity rate of the coupons should be less than 300 Angstroms. When monitored
reactivity rate is exceeded, the coupon should be analyzed for material species and a
corrective mitigation process put in place.
Storage time (unpowered) recommendation: do not exceed 6 consecutive months of
unpowered storage.
Note
6
Technical Specifications and Operating Limits
Systems and components must not experience changes in temperature and humidity that
are likely to cause condensation to form on or in that system or component. Do not
exceed the shipping and storage temperature gradient of 45°F/hr (25°C/hr).
Requirement Description
Ambient temperature -40° F to 149°F (-40°C to 65°C)
EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without
notice.
The information in this publication is provided as is. EMC Corporation makes no representations or warranties of any kind with
respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a
particular purpose. Use, copying, and distribution of any EMC software described in this publication requires an applicable software
license.
EMC², EMC, and the EMC logo are registered trademarks or trademarks of EMC Corporation in the United States and other countries.
All other trademarks used herein are the property of their respective owners.
For the most up-to-date regulatory document for your product line, go to EMC Online Support (https://support.emc.com).