UDC 621.882.215.3.091.2 January 1994
Product grade A cross recessed
pan head screws with collar
Linsenkoptschrauben mit Bund und Kreuzschiitz; Produktklasse A
In keeping with current practice in standards published by the International Organization for Standardization (ISO)
‘a comma has been used throughout as the decimal marker.
Dimensions in mm
1. Scope and field of application
This standard specifies requirements for M3 to M8 cross recessed pan head screws assigned to product grade
A See DIN 962 (or the standards referred to therein) for special screw types or finishes.
Hf, in special cases, screws are 10 comply with specifications other than those given in this standard (e.g. regarding
property class or material), these shall be selected in accordance with the relevant standards.
2 Dimensions
See figure 1 and table 1
NOTE: See DIN EN 20225 for notation.
As-rolled end
Cross recess
The diameter of the unthreaded shank Is equal to the thread diamoter or approximately equal to the pitch
diameter,
Figure 1
Continued on pages 2 to 4
229Page 2 DIN987
Table 1
Thread size (a) wa | 35) | Ma MS Me we
Py 05 06 o7 08 7 125
a monjaen 12 | 16 2 25
m |i | 3 | 38 | 38 38 38
dy om | 36 aa 47 57 68 | 92
4 75 90 00 | 118 145, 190)
es2 | ea2 | 042 | 108 | 198 | 18,6
i zis | 26 | 305 | 55 | «55 | 50
mm | 210 | 295 | 275 | 925 | 2s | 56
aa | ts 22
¢ seaeeeEereeiea
09 1.05 18
5 02 02 025 | oa
58 66 e2 | 10
eee 2 25 32
Sze 1 3 4
‘™m (auxiliary dimension) | 4a a6 7A 90
pa Hea 1 a ee eT
cross fear een : cael aac lieaes
‘m (auxiliary dimension) aa | az Cae
TyPeZ penewration ™ | _* “188 228 3.02 406
depth max 183 234 274 34a | 452
ae ‘Approximate mass (0 =7,85 kg/cm) per 1000 units, n kg
Nominal sizo| mn i
aaa 0
iitis 476 103 | 189
6 576 109 | 160 | 250
aiaiiaiien a a
10 on | 133 | tao | 298 | 588 |S
12 1165 | 145 | 208 19
4) 1365 as7 | 218 125
16 1565 18] 208 134
20 1958 193_| 262 144
2 | (2458 223 298 159)
ee) 253 | 308 175
35 m5 a3 | avi 190
40 385 1 408 206
| 45 445 eee eee eee [wry
50 495 | 237 |
(55) 54, [ 252
sai | eoost | =o
‘Commercial lengths are gen between stopped ines
") Use of sizes given in brackets should be avoided where possible.
2) P=pitch of thread
2) Sizes given above the dashed line are threaded up tothe head (i. thread length, b= ~a).3. Technical delivery conditions
DIN967 Page 3
Suracefinish
Table 2
Material ‘Steel Stainless steel
General requirements As specified in 180 8992.
Screw recess As specified in 180 4757")
Tolerance 69
Screw thread
AAs speaitied in DIN 13 Parts 19 and 15.
Property class :
Mechanical (material) 48 A2-70
properties?) — ap fe oo
‘As specified in DIN EN 20898 Part 1. 180 3506.
Limit deviations and peen ee 2
Geometrical tolerances As specified in 180 4759 Pan 1
Bright
Requirements for electroplating as in ISO 4042.
‘Other types of surtace protection shallbe the subjectof agreement
‘between customer and supplier.
Limit deviations for surface discontinuities as in DIN EN 26157
Patt 1
Acceptance inspection
1SO 3269 shall apply with regard to acceptance inspection.
+) Considered for adoption as a DIN EN Standard,
For), see page 2
4 Designation
Designation of an M5 pan head screw with collar, with a type Z cross recess and a length, /, of 20 mm, assigned to
Property class 4.8:
Pan head screw DIN 967-M5 x 20-4.8-Z
‘The DIN 4000-2-1 tabular layout of article characteristics shall apply to screws as covered in this standard,
231Page 4 DIN967
‘Standards referred to
DIN 13 Part 13, ISO metric screw threads; series of preferred sizes for screws, bolts and nuts from 1mm to
52 mm diameter and limits of size
DIN 13 Part 15 ISO metric screw threads; fundamental deviations and tolerances for screw threads of 1mm
diameter and larger
DIN 962 Designation system for fasteners
DIN 4000 Part 2 ‘Tabular layouts of article characteristics for screws and nuts
DIN EN 20225 Bolts, screws, studs and nuts; symbols and designations for dimensioning (ISO 225 : 1983)
DIN EN 20898 Part 1
DIN EN 26 157 Part 1
10 3269: 1988,
180 3506 : 1979
1S0 4042: 1989,
10 4757: 1983
180 4759-1:1978
10 8992: 1986
Machanical properties of fasteners; bolts, screws and studs (ISO 898-1 :1988)
Fasteners; surface discontinuities; bolts, screws and studs for general requirements
(ISO 6157-1 :1988)
Fasteners; acceptance inspection
Corrosion- resistant stainless steel fasteners; specifications
Threaded components; electroplated coatings
Cross recesses for screws
Tolerances for fasteners; bolts, screws and nuts with thread diameters from 1,6 to 150 mm;
product grades A, B and C
Fasteners; general requirements for bolts, screws, studs and nuts
International Patent Classification
F 16B.023/00
F 16B 035/00
232