UDC 621.882.6 August 1971
Bolted connections with waisted shank
Stud bolts
Schraubenverbindungen mit Dehnechaft; Schraubenbolsen
Dimensions in me
Lwith long threa
up to M52 DIN 2510
mera ¥
Contring for bole 44?)
gi. 8
as
‘Twpe K with short thread
up to M 56 DIN 2510 for M 64 DIN 2510 and upwards
(only for
upto Hse
other dimensions and detaile as for Type L and K
Z with long thread
up to M56 DIN 2510 for M 64 DIN 2510 and upwards
other dimensions and details as for Type L and
Yor Explanations see DIN 2510 Part 1 Continued on pages 2 and 3
250Page 2 DIN 2510 Part 3
‘ype 2 with long trend and spacer point
(only for use with cap mute at both ends)
pt A'56 BIN 2540 for H €4 DIN 2540 and upwards
t t
e .
ry + t
efede—by by +
49
other dimensions and details as for Type L and K
Designation of = atud-bolt Type L with thread dy = M 30 and nominal length = 200 an!) in
2icrHos (code letter Ge)):
Stud-volt LM 30 x 200 DIN 2510 - 24Crtos
aa] T T
iN 2510] wiz | sare | mao | ze | mar | mao | man | mae | man | maz | mas | man | sz | se
Pare 2
4 |» |e a zs | = vs
4 + pe 7 Bm 2
» os @
= [» =
= 7 | 8
i aa Fy
a a4 =a
wpa faa oe
a wpe fw
mro0x6 | mri0xe |at 120%] me128.8 | MaDe | soxa)| M1408 | OEY] MBO.
w>e > «| as | | w [ow | @ | mw [we | we
o> a] = s | «| «| «| 6
[sf %_ [sp
2s] = aja] ss] @
yf} Fe «|e | # a [a
ae a 7 = =
=~-[ = 7 = =
= [= [= ie |e)
als | = 2 [= [= [| 2
apal« s | s | ss ss
aalecen eee ‘ 7 7 ’
a = = = S
wp =p = 2 = =
(aL a T
Bracketed sizes should be avoided where possible.
1), 2) and 3) ove on page 3
251DIN 2510 Part 3 Page 3
Technice) conditions of delivery and asterials according to DIN 267 Part 13
1m according to DIN 267 Part 13
£ only to special order. The designation in this case rea:
Stud-polt LM 30 10 = f=
according to DIN 267 Part 13
agreed to the contrary when ordering, the marking should be applied to the end face
Vale:
of the point 22.
If stud-bolte of Types K, KU, Z or 2U for M G4 DIN 2510 and upwards are required without
hole dy, then the letter'O should be inserted in the designation, e-€.!
Stud-bolt KOM 6 DIN 2510 — 24Crto}
4) wominal lengtn (y to
fod when ordering (ave alao DIM! 2510 Part 1)
code letter of the material aay also be stated in the
Stud-boit LM 30 x 200 pIM 2510 - a
3) centring according to DIM 352 and detail T oaly for stud-Dolte of type f.
252UDC 621.882.626 August 1971
Bolted connections with waisted shank
Studs
Schraubenverbindungen mit Dehnachaft; Stiftschrauben
Dimensions in ms
ona Nut ena
eG with fat bearis Type P with long thread
14522
te
x
4]
bs
-—§t
Dype Q with short thread
bg
ia
other dimensions and details as for gther dimensions and details as for
‘Type G Type F
ye R with lone thre int
Heating hole for M 6% DIN 25105)
eran Y y ie ees cok eked oe
seating te bee 60 eee
S with short thresd and point
2eate
sw
other dimensions and details as for
a Type
For Explanations eee DIN 2510 Part 1 continued on pages 2 and 3
1) to 5) eee on pas
253Page 2 DIN 2510 Part 4
ecigusetia ocd va vans useat tau cal cips'0lsoa sue onal cg pela ave earuus 49
Degtenatton of e,cht vise seta tnt of we cane aur cmeags, 4
Stud GR M 30 x 150 DIN 2510 - 2xcrios
geude, | Miz | mie | m20 | M26 | maz | mao | maa | mas ma | maz | Mas
Part 2
Trread ds
ead | mas | M52 | mse | moa [M72x6/M90x6/M90%6] M100%6 | M110%6 | (M120x6)
Part 2 |
a ms] 4 |
0 » | 9 | 9
= a a
= 2 2 | 2
= vp oy»
6 wo | @ | 7
EI 7 | 0 | 9
7 96 | ia] 5
465 os | 675 | 765
7 v5 | ios | 195 | nes | ims | 1365
3 7
& 2
35 35
2 4
55 6
i
us| i535] 15
=| 85| es [ms [|e
se [sca [ odes eases esas
leat nate ARS
The bracketed size should be avoided where possible.
1), 2) ad 3) aoe on pase 3
254DIN 2510 Part 4 Page 3
Technical conditions of delivery ond aateriale according to DIN 267 Part 13
Type: m according to DIN 267 Part 13
f only to special order. The designation in this case r
‘Stua GR M 30 x 150 DIN 2510 - f— 24crtios
Marking: according to DIN 267 Part 13
Unlese agreed to the contrary when ordering, the marking should be applied to the end face
of the point 22 or to the end face at the mut end.
1) Wominal Length (4 to be atated when ordering (ore also DIM 2510 Part 1)
Stud GR M 30x 150 DIN 2510 - ¢
3) Centeing according to DIN 332 and detail ¥ only for studs of type f.
4) For M 64 DIN 2510 and upwards the angle te 150?
5) af atude for M64 DIN 2570 and upwards are required without nole dy, the Letter O should
ted
in the
‘Stud GRO M 64 x 400 DIN 2510 = 24crMos
255