Professional Documents
Culture Documents
www.Jameco.com ✦ 1-800-831-4242
The content and copyrights of the attached
material are the property of its owner.
DG202/DG212
The DG202/DG212 are normally open, quad single- ♦ Guaranteed ±4.5V to ±18V Operation
pole single-throw (SPST) analog switches. These ♦ No VL Supply Required
CMOS switches can be continuously operated with
power supplies ranging from ±4.5V to ±18V. Maxim ♦ Nonlatching with Supplies Turned Off and Input
guarantees that these switches will not latch up if the Signals Present
power supplies are disconnected with input signals still ♦ CMOS and TTL Logic Compatible
connected. ♦ Monolithic, Low-Power CMOS Design
The DG202/DG212 are similar to the DG201/DG211
except for inverted control inputs. All devices have Ordering Information
guaranteed break-before-make switching, as well as PART TEMP RANGE PIN-PACKAGE
essentially constant on-resistance over the analog
DG202CUE 0°C to +70°C 16 TSSOP
signal range. All switches conduct current in either
direction and add no offset to the output signal. DG202CSE 0°C to +70°C 16 SO
Compared to the original manufacturer’s products, DG202CJ 0°C to +70°C 16 Plastic DIP
Maxim’s DG202/DG212 consume very little power, DG202C/D 0°C to +70°C Dice
making them better suited for portable applications. DG202AEGE -40°C to +85°C 16 QFN (5mm x 5mm)
Maxim has also eliminated the need for the third logic DG202AEUE -40°C to +85°C 16 TSSOP
power supply (VL) that is required for the operation of
the original manufacturer’s DG212 without sacrificing DG202ADY -40°C to +85°C 16 SO
compatibility. DG202ADJ -40°C to +85°C 16 Plastic DIP
DG202AK -55°C to +125°C 16 CERDIP
Applications DG212CUE 0°C to +70°C 16 TSSOP
IN1 1 16 IN2
5kΩ D1 2 15 D2
5kΩ * 1 16 *
40kΩ S1 3 14 S2
VIN x 10V 2 15
V- 4 13 V+
3 14
VOUT GND 5 DG202 12 V L
-15V 4 DG202 13 +15V DG212
DG212 S4 6 11 S3
5 12
6 11 D4 7 10 D3
7 10 IN4 8 9 IN3
10kΩ 20kΩ
* 8 9 *
DIP/SO
LOGIC SWITCH
0 OFF
PROGRAMMABLE GAIN AMPLIFIER
1 ON
NOTE: *PINS 1, 8, 9, AND 16 ARE LOGIC CONTROL INPUTS
SWITCHES SHOWN FOR LOGIC “0” INPUT
Pin Configurations continued at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Quad SPST CMOS Analog Switches
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2 _______________________________________________________________________________________
Quad SPST CMOS Analog Switches
DG202/DG212
(V+ = +15V, V- = -15V, GND = 0, TA = +25°C, unless otherwise noted.) (For more information on TYP values see Note 2.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
SUPPLY
Positive Supply Current I+ 0.02 0.4
Negative Supply Current I- VIN = 0 and 2.4V (all) 0.01 0.4 mA
Logic Supply Current IL 0 0
Power-Supply Range
VOP ±4.5 ±18.0 V
for Continous Operation
Note 2: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
Note 3: ID(ON) is leakage from driver into “ON” switch.
Note 4: OFF-Isolation = 20 log VS/VD, VS = input to OFF switch, VD = output.
Note 1: Signals on S_, D_, or IN_ exceeding V+ or V- on Maxim’s DG202 will be clamped by internal diodes, and are also internally cur-
rent limited to 25mA.
Note 2: Device mounted with all leads soldered to PC board.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
_______________________________________________________________________________________ 3
Quad SPST CMOS Analog Switches
(V+ = +15V, V- = -15V, GND = 0, TA = +25°C, unless otherwise noted.) (For more information on TYP values see Note 3.)
DG202A DG202C, D, E
PARAMETER SYMBOL CONDITIONS UNITS
MIN TYP MAX MIN TYP MAX
INPUT
Input Current with Input VIN = 2.4V -1.0 -0.0004 -1.0 -0.0004
IINH
Voltage High VIN = 15V 0.003 1.0 0.003 1.0
µA
Input Current with Input
IINL VIN = 0 -1.0 -0.0004 -1.0 -0.0004
Voltage Low
DYNAMIC
Turn-ON Time tON See Figure 1 Switching Time 480 600 480 600
ns
Turn-OFF Time tOFF1 Test Circuit 370 450 370 450
CL = 1000pF, VGEN = 0,
Charge Injection Q 20 20 pC
RGEN = 0
Source OFF-Capacitance CS (OFF) VS = 0, 5 5
Drain OFF-Capacitance CD (OFF) VIN = 0 5 5
f = 140kHz pF
CD (ON) VD = VS = 0,
Channel ON-Capacitance 16 16
+ CS (ON) VIN = 5V
OFF-Isolation VIN = 0, ZL = 75Ω 70 70
Crosstalk dB
VS = 2.0V, f = 100kHz 90 90
(Channel to Channel)
SUPPLY
Positive Supply Current I+ All channels ON or OFF 0.02 0.1 0.02 0.1
mA
Negative Supply Current I- All channels ON or OFF -0.1 -0.01 -0.1 -0.01
Power-Supply Range for
VOP ±4.5 ±18 ±4.5 ±18.0 V
Continuous Operation
Note 3: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
Note 4: ID (ON) is leakage from driver into “ON” switch.
4 _______________________________________________________________________________________
Quad SPST CMOS Analog Switches
DG202/DG212
(V+ = +15V, V- = -15V, GND = 0, TA = full opearting temperature range, unless otherwise noted.) (For more information on TYP
values see Note 3.)
DG202A DG202C, D, E
PARAMETER SYMBOL CONDITIONS UNITS
MIN TYP MAX MIN TYP MAX
SWITCH
Analog Signal Range VANALOG -15 +15 -15 +15 V
Drain-Source ON Resistance
RDS (ON) VD = ±10V, VIN = 2.4V, IS = 1mA 250 250 Ω
(Note 5)
VS = 14V, VD = -14V 100 100
Source OFF-Leakage Current IS (OFF) VIN = 0.8V
VS = -14V, VD = 14V -100 -100
VS = 14V, VD = -14V 100 100
Drain OFF-Leakage Current ID (OFF) VIN = 0.8V nA
VS = -14V, VD = 14V -100 -100
Drain ON-Leakage Current VS = -14V 200 200
ID (ON) VIN = 2.4V
(Note 6) VD = 14V -200 -200
INPUT
Input Current with Input VIN = 2.4V -1.0 -1.0
IINH
Voltage High VIN = 15V 1.0 1.0
µA
Input Current with Input
IINL VIN = 0 -1.0 -1.0
Voltage Low
Note 5: Electrical characteristics, such as On-Resistance, will change when power supplies other than ±15V, are used.
Note 6: ID (ON) is leakage from driver into “ON” switch.
Pin Description
PIN
NAME FUNCTION
DIP/SO/TSSOP QFN/TQFN
1, 16, 9, 8 15, 14, 7, 6 IN1–IN4 Input
2, 15, 10, 7 16, 13, 8, 5 D1–D4 Analog Switch Drain Terminal
3, 14, 11, 6 1, 12, 9, 4 S1–S4 Analog Switch Source Terminal
4 2 V- Negative-Supply Voltage Input
5 3 GND Ground
12 10 N.C. No Connection
13 11 V+ Positive-Supply Voltage Input—Connected to Substrate
— EP EP Exposed Pad. Connect exposed pad to V+ or leave EP unconnected.
_______________________________________________________________________________________ 5
Quad SPST CMOS Analog Switches
DG202/DG212
RL
LOGIC VO = VS
RL + rDS(ON)
INPUT LOGIC 1 SW ON +15V
3V
t r < 20ns SWITCH V+
50% INPUT SWITCH
t f < 20ns
0 S1 D1 OUTPUT
VS = +2V VO
SWITCH LOGIC
INPUT VS INPUT IN1 RL CL
VO 0.9 VO 0.9 1kΩ 35pF
SWITCH 0 VO 0.1
OUTPUT tOFF tOFF1 GND V- (REPEAT TEST FOR IN2, IN3, AND IN4)
tOFF2
0V -15V
Typical RDS(ON) vs. Power Supplies for Maxim’s DG202, and DG212
RDS(ON) AT ANALOG SIGNAL LEVEL
POWER SUPPLIES
-5V +5V -10V +10V -15V +15V
±5V 350Ω 380Ω — — — —
±10V — — 165Ω 250Ω — —
±15V — — 125Ω 160Ω 135Ω 155Ω
8 9
S1 1 12 S2
V- 2 11 V+
DG202
DG212
GND 3 10 N.C.
*EP
S4 4 9 S3
5 6 7 8
D4 IN4 IN3 D3
TQFN*
*EXPOSED PAD. CONNECT EXPOSED PAD TO V+
OR LEAVE EXPOSED PAD UNCONNECTED.
6 _______________________________________________________________________________________
Quad SPST CMOS Analog Switches
Package Information
DG202/DG212
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
SOICN .EPS
INCHES MILLIMETERS
DIM MIN MAX MIN MAX
A 0.053 0.069 1.35 1.75
N A1 0.004 0.010 0.10 0.25
B 0.014 0.019 0.35 0.49
C 0.007 0.010 0.19 0.25
e 0.050 BSC 1.27 BSC
E 0.150 0.157 3.80 4.00
E H H 0.228 0.244 5.80 6.20
L 0.016 0.050 0.40 1.27
VARIATIONS:
1
INCHES MILLIMETERS
TOP VIEW DIM MIN MAX MIN MAX N MS012
D 0.189 0.197 4.80 5.00 8 AA
D 0.337 0.344 8.55 8.75 14 AB
D 0.386 0.394 9.80 10.00 16 AC
A C
e B A1 0∞-8∞
L
FRONT VIEW SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
_______________________________________________________________________________________ 7
Quad SPST CMOS Analog Switches
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PDIPN.EPS
8 _______________________________________________________________________________________
Quad SPST CMOS Analog Switches
DG202/DG212
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
CDIPS.EPS
_______________________________________________________________________________________ 9
Quad SPST CMOS Analog Switches
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
PACKAGE OUTLINE, TSSOP 4.40mm BODY
1
21-0066 G 1
10 ______________________________________________________________________________________
Quad SPST CMOS Analog Switches
DG202/DG212
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
32L QFN.EPS
______________________________________________________________________________________ 11
Quad SPST CMOS Analog Switches
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
QFN THIN.EPS
Revision History
Pages changed at Rev3: 1–6, 11
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.